Add a generic /memory node in each Tegra DTSI (with empty reg property,
to be overidden by each DTS) and set proper unit address for /memory
nodes to fix the DTC warnings:
arch/arm/boot/dts/tegra20-harmony.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
The DTB after the change is the same as before except adding
unit-address to /memory node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARM GIC only supports interrupts with either level-high or
rising-edge types for SPIs. The interrupt type for the Palmas PMIC used
for Tegra114 boards is specified as level-low which is invalid for the
GIC. This has gone undetected because until recently, failures to set
the interrupt type when the interrupts are mapped via firmware (such as
device-tree) have not been reported. Since commits 4b357daed6
("genirq: Look-up trigger type if not specified by caller") and
1e2a7d7849 ("irqdomain: Don't set type when mapping an IRQ"), failure
to set the interrupt type will cause the requesting of the interrupt to
fail and exposing incorrectly configured interrupts.
Please note that although the interrupt type was never being set for the
Palmas PMIC, it was still working fine, because the default type setting
for the interrupt, 'level-high', happen to match the correct type for
the interrupt.
Finally, it should be noted that the Palmas interrupt from the PMIC is
actually 'level-low', however, this interrupt signal is inverted by the
Tegra PMC and so the GIC actually sees a 'level-high' interrupt which is
what should be specified in the device-tree interrupt specifier.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This seems to have been copied and pasted since the beginning of time,
though only until Tegra124, likely because that DT was written from
scratch or it was fixed along the way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "nvidia,wakeup-source" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
vddio_sdmmc3 is a vdd_io, and thus should be under the vqmmc-supply
property, not vmmc-supply.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This property was wrong and broke eMMC since commit 52221610d ("mmc:
sdhci: Improve external VDD regulator support"). Align the eMMC
properties to those of other Tegra boards.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are general changes pending to make the /aliases/serial* entries
number the serial ports on the system. On Tegra, so far the ports have
been just numbered dynamically as they are configured so that makes them
change.
To avoid this, add specific aliases per board to keep the old numbers.
This allows us to change the numbering by default on future SoCs while
keeping the numbering on existing boards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra DSI support has been fixed to support continuous clock behavior that
the panel used on SHIELD requires, so finally add its device tree node
since it is functional.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Input had been disabled by mistake on these pins, leading to issues with
SDIO devices like the Wifi module not being probed or random errors
occuring on the SD card.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The pinmux subsystem complained that the nvidia,low-power-mode property
is not supported by the sdio1, sdio3 and gma drive groups. In addition
gma also does not support nvidia,drive-type. Remove these properties so
the pinmux configuration can properly be applied.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA SHIELD is a portable Android console containing a Tegra 4 SoC with
2GB RAM and a 720p panel.
The following hardware is enabled by this device tree: UART, eMMC, USB
(needs external power), PMIC, backlight, joystick, SD card, GPIO keys.
DSI panel, HDMI output, charger, self-powered USB, audio, wifi bluetooth
are not supported yet but might be by future patches (likely in that
order).
Touch panel and sensors will probably never be supported.
Initrd addresses are hardcoded to match the static values used by the
bootloader, since it won't add them for us. All the same, a kernel
command-line is provided to replace the one passed by the
bootloader which is filled with garbage.
NVIDIA SHIELD is typically booted with an appended DTB to avoid
modifications made by the bootloader.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[swarren, fixed gpio-keys child node sort order, patch description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
