SDHCI changed from using a tasklet to finish requests, to using an IRQ
thread i.e. commit c07a48c265 ("mmc: sdhci: Remove finish_tasklet").
Because this increased the latency to complete requests, a preparatory
change was made to complete the request from the IRQ handler if
possible i.e. commit 19d2f695f4 ("mmc: sdhci: Call mmc_request_done()
from IRQ handler if possible"). That alleviated the situation for MMC
block devices because the MMC block driver makes use of mmc_pre_req()
and mmc_post_req() so that successful requests are completed in the IRQ
handler and any DMA unmapping is handled separately in mmc_post_req().
However SDIO was still affected, and an example has been reported with
up to 20% degradation in performance.
Looking at SDIO I/O helper functions, sdio_io_rw_ext_helper() appeared
to be a possible candidate for making use of asynchronous requests
within its I/O loops, but analysis revealed that these loops almost
never iterate more than once, so the complexity of the change would not
be warrented.
Instead, mmc_pre_req() and mmc_post_req() are added before and after I/O
submission (mmc_wait_for_req) in mmc_io_rw_extended(). This still has
the potential benefit of reducing the duration of interrupt handlers, as
well as addressing the latency issue for SDHCI. It also seems a more
reasonable solution than forcing drivers to do everything in the IRQ
handler.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: c07a48c265 ("mmc: sdhci: Remove finish_tasklet")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200903082007.18715-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
- Add a new host cap bit and a corresponding DT property, to support power
cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host:
- Convert a few DT bindings to the json-schema
- mtk-sd: Add support for command queue through cqhci
- mtk-sd: Add support for the MT6779 variant
- renesas_sdhi_internal_dmac: Fix dma unmapping in the error path
- sdhci_am654: Add support for the AM65x PG2.0 variant
- sdhci_am654: Extend support for phys/clocks
- sdhci-cadence: Drop incorrect HW tuning for SD mode
- sdhci-msm: Add support for interconnect bandwidth scaling
- sdhci-msm: Enable internal voltage control
- sdhci-msm: Enable low power state for pinctrls
- sdhci-of-at91: Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli: Improve clock handling for GL975x
- sdhci-pci-o2micro: Add HW tuning for SDR104 mode
- sdhci-pci-o2micro: Fix support for O2 host controller Seabird1
-----BEGIN PGP SIGNATURE-----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=AwwR
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
The commit 5a36d6bcdf ("mmc: core: Add DT-bindings for
MMC_CAP2_FULL_PWR_CYCLE") added the "full-pwr-cycle" property which
is possible to perform a full power cycle of the card at any time.
However, some environment (like r8a77951-salvator-xs) is possible
to perform a full power cycle of the card in suspend via firmware
(PSCI on arm-trusted-firmware). So, in worst case, since we are
not doing a graceful shutdown of the eMMC device (just cut VCCQ
while the eMMC is "sleeping") in suspend, it could lead to internal
data corruptions. So, add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
to do a graceful shutdown which issues Power Off notification
before entering system suspend.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594123122-13156-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Correcting this misspelling squashes the following W=1 build warning(s):
mmc/core/queue.c:212: warning: Function parameter or member 'mq' not described in '__mmc_init_request'
mmc/core/queue.c:212: warning: Excess function parameter 'q' description in '__mmc_init_request'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-8-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remainder of the kerneldoc descriptions look present and correct.
Fixes the following W=1 kernel build warnings:
drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'mmc' not described in 'mmc_regulator_set_vqmmc'
drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'ios' not described in 'mmc_regulator_set_vqmmc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-4-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add missing kerneldoc entry for sdio_set_host_pm_flags()'s 'flag'
function argument.
Fixes the following W=1 kernel build warning:
kernel/drivers/mmc/core/sdio_io.c:722: warning: Function parameter or member 'flags' not described in 'sdio_set_host_pm_flags'
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-3-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all source files which include quirks.h make use of the all of
the available fixup information. When this happens the compiler
complains that some constant variables are defined by never used.
We can fix this by telling the compiler that this intentional by
simply marking them as __maybe_unused.
Fixes the following W=1 kernel build warnings:
In file included from drivers/mmc/core/sdio.c:22:
drivers/mmc/core/quirks.h:105:31: warning: ‘mmc_ext_csd_fixups’ defined but not used [-Wunused-const-variable=]
105 | static const struct mmc_fixup mmc_ext_csd_fixups[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
In file included from drivers/mmc/core/mmc.c:25:
drivers/mmc/core/quirks.h:123:31: warning: ‘sdio_fixup_methods’ defined but not used [-Wunused-const-variable=]
123 | static const struct mmc_fixup sdio_fixup_methods[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
Cc: Andrei Warkentin <andreiw@motorola.com>
Cc: Martin Mares <mj@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-2-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the default power mode, MMC_POWER_UNDEFINED, in mmc_alloc_host() rather
than in mmc_start_host(). This enables host drivers to make use of the
initial state during ->probe().
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link:
https://lore.kernel.org/r/1592919288-1020-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In current code logic, when work in SDR12/SDR25 mode, the final clock
rate is incorrect, just the legancy 400KHz, because the
card->sw_caps.sd3_bus_mode do not has the flag SD_MODE_UHS_SDR12 or
SD_MODE_UHS_SDR25. Besides, SDIO_SPEED_SDR12 is actually value 0, and
every mode need to config the timing and clock rate, so remove the
‘if’ operator.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Tested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1592813959-5914-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 6b5eda369a ("sdio: put active devices into 1-bit mode during
suspend") disabled 4-bit mode during system suspend. After this patch,
commit 7310ece86a ("mmc: implement SD-combo (IO+mem) support") used
new sdio_enable_4bit_bus() instead of sdio_enable_wide() to support
SD-combo cards, also for card resume. However, no corresponding support
added during suspend. That is not correct. Let's fix it.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200609081431.6376-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card type is SD combo(MMC_TYPE_SD_COMBO) and the memory part does
not support wider bus(SD_SCR_BUS_WIDTH_4), nothing will be done except
return 0. However, we should check whether IO part support wider bus or
not. We should use available IO ability if supported.
In addition, there's a duplicated check to MMC_CAP_4_BIT_DATA since
sdio_enable_wide() will include that check. And we can also save one
call site to sdio_enable_wide() after this change.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200608103009.5000-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should return any possible error returned by mmc_io_rw_direct()
rather than only -EIO in sdio_disable_func() failure path.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200604100102.13572-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The approach to allow userspace ~5s to consume the uevent, which is
triggered when a new card is inserted/initialized, currently requires the
mmc host to support system wakeup.
This is unnecessary limiting, especially for an mmc host that relies on a
GPIO IRQ for card detect. More precisely, the mmc host may not support
system wakeup for its corresponding struct device, while the GPIO IRQ still
could be configured as a wakeup IRQ via enable_irq_wake().
To support all various cases, let's simply drop the need for the wakeup
support. Instead let's always register a wakeup source and activate it for
all card detect IRQs by calling __pm_wakeup_event().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200529102341.12529-1-ulf.hansson@linaro.org
The mmc driver doesn't support event notifications, which means
that check_disk_change is a no-op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the call to blk_should_fake_timeout out of blk_mq_complete_request
and into the drivers, skipping call sites that are obvious error
handlers, and remove the now superflous blk_mq_force_complete_rq helper.
This ensures we don't keep injecting errors into completions that just
terminate the Linux request after the hardware has been reset or the
command has been aborted.
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
In this case, use fifo_low, because it only cares about being above
SCHED_NORMAL. Effectively no change in behaviour.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Device/vendor ids from Common CIS (Card Information Structure) may be
different as device/vendor ids from CIS on particular SDIO function.
Kernel currently exports only device/vendor ids from SDIO functions and not
"main" device/vendor ids from Common CIS.
This patch exports "main" device/vendor ids for SDIO and SD combo cards at
top level mmc device in sysfs hierarchy.
Userspace can use e.g. udev rules to correctly match whole SDIO card based
on Common CIS device/vendor id and not only one particular SDIO function.
Having this information in userspace also helps developers to debug whole
SDIO card as e.g. kernel mmc quirks use device/vendor ids from Common CIS
and not from particular SDIO function. Also it allows to write userspace
applications which list all connected SDIO cards based on CIS ids.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO non-combo cards are not handled by mmc_block driver and do not have
accessible CID register which is used for MMC_NAME= construction.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-1-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell SDIO device ID 0x9134 is used in SDIO Common CIS (Card Information
Structure) and not in SDIO wlan function (with ID 1). SDIO Common CIS is
accessed by function ID 0.
So change this misleading macro name to SDIO_DEVICE_ID_MARVELL_8887_F0 as
it does not refer to wlan function. It refers to function 0.
Wlan module on this SDIO card is available at function ID 1 and is
identified by different SDIO device ID 0x9135. Kernel quirks for SDIO
devices are matched against device ID from SDIO Common CIS. Therefore
device ID used in quirk is correct, just has misleading name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Step by step, mmc host drivers and the mmc core have been improved in
regards to support erase/discard/trim operations. We have now reached a
point when it no longer seems reasonable to use an opt-in approach to
enable the functionality. Therefore, let's switch to make the operations
always supported.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508112853.23525-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Following eMMC JEDEC JESD84-B51 standard, an enhanced form of
rpmb is supported. What this enhanced mode supports is in addition
to be able to write one rpmb or two rpmb frames at a time,
32 frames can be written at a time.
Expose this information present in ext csd field so that the
user space application that wants to make use of this can do so.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1588341189-4371-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the comment in mmc_sdio_reinit_card(), some SDIO cards may
require a "[CMD5,5,3,7] init sequence", which isn't always obeyed in
mmc_sdio_init_card(). Especially, when we end up retrying the UHS-I
specific initialization, there is a missing CMD5.
Let's update the code to make the behaviour consistent and let's also take
the opportunity to clean up the code a bit, to avoid open coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-5-ulf.hansson@linaro.org
While initializing an SDIO card in mmc_sdio_init_card(), we may need to
retry the UHS-I specific initialization, in case the first attempt fails.
This leads to resending a CMD8, but also to restart from scratch with the
so called OCR mask negotiations. This is unnecessary as we already have a
negotiated OCR mask, so let's use that instead. In this way, the behaviour
also becomes more consistent with other similar paths.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-4-ulf.hansson@linaro.org
Over the years, the code in mmc_sdio_init_card() has grown to become quite
messy. Unfortunate this has also lead to that several paths are leaking
memory in form of an allocated struct mmc_card, which includes additional
data, such as initialized struct device for example.
Unfortunate, it's a too complex task find each offending commit. Therefore,
this change fixes all memory leaks at once.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-3-ulf.hansson@linaro.org
During some scenarios mmc_sdio_init_card() runs a retry path for the UHS-I
specific initialization, which leads to removal of the previously allocated
card. A new card is then re-allocated while retrying.
However, in one of the corresponding error paths we may end up to remove an
already removed card, which likely leads to a NULL pointer exception. So,
let's fix this.
Fixes: 5fc3d80ef4 ("mmc: sdio: don't use rocr to check if the card could support UHS mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-2-ulf.hansson@linaro.org
Fixes coccicheck warning:
drivers/mmc/core/debugfs.c:222:0-23: WARNING: mmc_clock_fops should be
defined with DEFINE_DEBUGFS_ATTRIBUTE
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files
Fixes: 703aae3d09 ("mmc: add a file to debugfs for changing host clock at runtime")
Fixes: a04c50aaa9 ("mmc: core: no need to check return value of debugfs_create functions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1587633319-19835-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the well defined HIGH_SPEED_BUS_SPEED macro in mmc_sd_switch_hs()
to make code more readable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200410145643.630b0731@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adjust mmc_regulator_set_vqmmc() to return 1 if the voltage switch was
skipped because the regulator voltage was already correct. This allows
drivers to detect such condition and possibly skip various voltage
switching extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-2-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data structure member “rpmb->md” was passed to a call of the function
“mmc_blk_put” after a call of the function “put_device”. Reorder these
function calls to keep the data accesses consistent.
Fixes: 1c87f73578 ("mmc: block: Fix bug when removing RPMB chardev ")
Signed-off-by: Peng Hao <richard.peng@oppo.com>
Cc: stable@vger.kernel.org
[Uffe: Fixed up mangled patch and updated commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
First, it should be noted that the CQE timeout (60 seconds) is substantial
so a CQE request that times out is really stuck, and the race between
timeout and completion is extremely unlikely. Nevertheless this patch
fixes an issue with it.
Commit ad73d6fead ("mmc: complete requests from ->timeout")
preserved the existing functionality, to complete the request.
However that had only been necessary because the block layer
timeout handler had been marking the request to prevent it from being
completed normally. That restriction was removed at the same time, the
result being that a request that has gone will have been completed anyway.
That is, the completion was unnecessary.
At the time, the unnecessary completion was harmless because the block
layer would ignore it, although that changed in kernel v5.0.
Note for stable, this patch will not apply cleanly without patch "mmc:
core: Fix recursive locking issue in CQE recovery path"
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: ad73d6fead ("mmc: complete requests from ->timeout")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200508062227.23144-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Consider the following stack trace
-001|raw_spin_lock_irqsave
-002|mmc_blk_cqe_complete_rq
-003|__blk_mq_complete_request(inline)
-003|blk_mq_complete_request(rq)
-004|mmc_cqe_timed_out(inline)
-004|mmc_mq_timed_out
mmc_mq_timed_out acquires the queue_lock for the first
time. The mmc_blk_cqe_complete_rq function also tries to acquire
the same queue lock resulting in recursive locking where the task
is spinning for the same lock which it has already acquired leading
to watchdog bark.
Fix this issue with the lock only for the required critical section.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Suggested-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588868135-31783-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the request completion path with CQE, request type is being checked
after the request is getting completed. This is resulting in returning
the wrong request type and leading to the IO hang issue.
ASYNC request type is getting returned for DCMD type requests.
Because of this mismatch, mq->cqe_busy flag is never getting cleared
and the driver is not invoking blk_mq_hw_run_queue. So requests are not
getting dispatched to the LLD from the block layer.
All these eventually leading to IO hang issues.
So, get the request type before completing the request.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588775643-18037-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following sparse warning:
drivers/mmc/core/mmc_ops.c:881:5: warning: symbol 'mmc_interrupt_hpi'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Fixes: 55c2b8b9a3 ("mmc: core: Re-work the code for eMMC sanitize")
Link: https://lore.kernel.org/r/20200403034727.11879-1-yanaijie@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path for sanitize operations that completes with -ETIMEDOUT, is
tightly coupled with the internal request handling code of the core. More
precisely, mmc_wait_for_req_done() checks for specific sanitize errors.
This is not only inefficient as it affects all types of requests, but also
hackish.
Therefore, let's improve the behaviour by moving the error path out of the
mmc core. To do that, retuning needs to be held while running the sanitize
operation.
Moreover, to avoid exporting unnecessary symbols to the mmc block module,
let's move the code into the mmc_ops.c file. While updating the actual
code, let's also take the opportunity to clean up some of the mess around
it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200316152152.15122-1-ulf.hansson@linaro.org
Supply a separate sg list for each of the request in non-blocking
IO test cases where two requests will be issued at same time.
Otherwise, sg memory may get unmapped when a request is done while
same memory is being accessed by controller from the other request,
and it leads to iommu errors with below call stack:
__arm_lpae_unmap+0x2e0/0x478
arm_lpae_unmap+0x54/0x70
arm_smmu_unmap+0x64/0xa4
__iommu_unmap+0xb8/0x1f0
iommu_unmap_fast+0x38/0x48
__iommu_dma_unmap+0x88/0x108
iommu_dma_unmap_sg+0x90/0xa4
sdhci_post_req+0x5c/0x78
mmc_test_start_areq+0x10c/0x120 [mmc_test]
mmc_test_area_io_seq+0x150/0x264 [mmc_test]
mmc_test_rw_multiple+0x174/0x1c0 [mmc_test]
mmc_test_rw_multiple_sg_len+0x44/0x6c [mmc_test]
mmc_test_profile_sglen_wr_nonblock_perf+0x6c/0x94 [mmc_test]
mtf_test_write+0x238/0x3cc [mmc_test]
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582714668-17247-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case the host specify a max_busy_timeout, we need to validate that the
needed timeout for the HPI command conforms to that requirement. If that's
not the case, let's convert from a R1B response to a R1 response, as to
instruct the host to avoid HW busy detection.
Additionally, when R1B is used we must also inform the host about the busy
timeout for the command, so let's do that via updating cmd.busy_timeout.
Finally, when R1B is used and in case the host supports HW busy detection,
there should be no need for doing polling, so then skip that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-12-ulf.hansson@linaro.org
Rather than open coding the polling loop in mmc_interrupt_hpi(), let's
convert to use mmc_poll_for_busy().
Note that, moving to mmc_poll_for_busy() for HPI also improves the
behaviour according to below.
- Adds support for polling via the optional ->card_busy() host ops.
- Require R1_READY_FOR_DATA to be set in the CMD13 response before exiting
the polling loop.
- Adds a throttling mechanism to avoid CPU hogging when polling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-11-ulf.hansson@linaro.org
The 'u32 *status' is unused by the caller, so let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-10-ulf.hansson@linaro.org
Rather than open coding the polling loop in mmc_do_erase(), let's convert
to use mmc_poll_for_busy().
To allow a slightly different error parsing during polling, compared to the
__mmc_switch() case, a new in-parameter to mmc_poll_for_busy() is needed,
but other than that the conversion is straight forward.
Besides addressing the open coding issue, moving to mmc_poll_for_busy() for
erase/trim/discard improves the behaviour according to below.
- Adds support for polling via the optional ->card_busy() host ops.
- Returns zero to indicate success when the final polling attempt finds the
card non-busy, even if the timeout expired.
- Exits the polling loop when state moves to R1_STATE_TRAN, rather than
when leaving R1_STATE_PRG.
- Decreases the starting range for throttling to 32-64us.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-9-ulf.hansson@linaro.org
Through mmc_poll_for_busy() a CMD13 may be sent to get the status of the
(e)MMC card. If the state of the card is R1_STATE_PRG, the card is
considered as being busy, which means we continue to poll with CMD13. This
seems to be sufficient, but it's also unnecessary fragile, as it means a
new command/request could potentially be sent to the card when it's in an
unknown state.
To try to improve the situation, but also to move towards a more consistent
CMD13 polling behaviour in the mmc core, let's deploy the same policy we
use for regular I/O write requests. In other words, let's check that card
returns to the R1_STATE_TRAN and that the R1_READY_FOR_DATA bit is set in
the CMD13 response, before exiting the polling loop.
Note that, potentially this changed behaviour could lead to unnecessary
waiting for the timeout to expire, if the card for some reason, moves to an
unexpected error state. However, as we bail out from the polling loop when
R1_SWITCH_ERROR bit is set or when the CMD13 fails, this shouldn't be an
issue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-8-ulf.hansson@linaro.org
To allow subsequent changes to re-use the code from the static function
mmc_blk_in_tran_state(), let's move it to a public header. While at it,
let's also rename it to mmc_ready_for_data(), as to try to better describe
its purpose.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-7-ulf.hansson@linaro.org
To make the code more readable, move the part that gets the busy status of
the card out into a separate function, mmc_busy_status(). Then call it from
mmc_poll_for_busy().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-6-ulf.hansson@linaro.org
The use_busy_signal in-parameter is set true by all callers of
__mmc_switch(), hence it's redundant so drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-5-ulf.hansson@linaro.org
To simplify code, let's extend mmc_switch_status() to cope with needs
addressed in __mmc_switch_status(). Then move all users to the updated
mmc_switch_status() API and drop __mmc_switch_status() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-4-ulf.hansson@linaro.org
The last user of MMC_OPS_TIMEOUT_MS was recently removed, however the
define stayed around. Let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-3-ulf.hansson@linaro.org
In mmc_poll_for_busy() we loop continuously, either by sending a CMD13 or
by invoking the ->card_busy() host ops, as to detect when the card stops
signaling busy. This behaviour is problematic as it may cause CPU hogging,
especially when the busy signal time reaches beyond a few ms.
Let's fix the issue by adding a throttling mechanism, that inserts a
usleep_range() in between the polling attempts. The sleep range starts at
32-64us, but increases for each loop by a factor of 2, up until the range
reaches ~32-64ms. In this way, we are able to keep the loop fine-grained
enough for short busy signaling times, while also not hogging the CPU for
longer times.
Note that, this change is inspired by the similar throttling mechanism that
we already use for mmc_do_erase().
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-2-ulf.hansson@linaro.org
Adrian Hunter