If the primary gets marked as disabled while the pipe is off for
instance, we should still re-enable it when the pipe is turned on,
unless the sprite covers it fully also in that configuration.
Unfortunately we do the plane visibility checks only in the sprite code,
which is executed after the primary enabling when turning the pipe off.
Ideally we should compute the plane visibility before touching the
hardware at all, but for now just set the primary_disabld flag
in intel_{enable,disable}_plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If channel equalization succeeds, there's no indication something went
wrong in clock recovery (unless debug is enabled). We should shout about
the failures and fix them instead of hiding them under the carpet.
This has allowed bugs like [1] stay dormant for a long time.
[1] https://bugs.freedesktop.org/show_bug.cgi?id=70117
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The VGACNTRL register contains a bunch of other stuff besides
the VGA_DISP_DISABLE bit. When we write the register we always set those
other bits to zero, so normally the current check would work.
However on HSW disabling and re-enabling the power well will reset the
VGACNTRL register to its default value, which has several of the other
bits set as well.
So only look at the VGA_DISP_DISABLE bit when checking whether the VGA
plane needs re-disabling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Everyone else uses intel_PLL_is_valid(), so make VLV use it as well.
We don't have any special p and m limits on VLV, so skip those tests,
and we also need to skip the m1<=m2 test line PNV.
Reorganize the function a bit to move the n check alongside the rest of
the test for the non-derived dividers, and check the derived values
afterwards.
Note that this changes vlv_find_best_dpll() in two ways:
- The .vco comparison is now >max instead of >=max, and since we round
down when calculating that stuff, we may now allow frequencies slightly
above the max as we do on other platforms. The previous method
disallowed exactly max and anything above it.
- We now check the .dot frequency against the data rate limits, which we
didn't do before.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If vlv_find_best_dpll() couldn't find suitable PLL settings,
just say so instead of lying to caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After aligning the p1 divider limits, and removing the unused p and m
limits, intel_limits_vlv_dac and intel_limits_vlv_hdmi are identical.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't use .dot_limit for anything on VLV, so don't populate it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never check the p and m limits (which according to comments are
based on someone's guesswork), so just remove them.
VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm has no p and m
limits listed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm tells us that the
minimum p2 divider is 2. Use that limit on the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm p1
can be 2-3 always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some reason there's a sort of off by one issue with the p1 divider.
The actual p1 limits according to
VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm is 2-3, so we should
just say that instead of saying 1-3 and avoiding the 1 via the choice of
comparison operator.
I don't know why we're using different p1 limits for intel_limits_vlv_dac
and intel_limits_vlv_hdmi, but let's preserve that for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We limit the maximum n divider value in order to make sure the PLL's
reference inout is at least 19.2 MHz. I assume that is done to satisfy
some hardware requirement.
However we never check whether that calculated limit is below the
maximum supoorted N divider value (7). In practice that is always true
since we only support 100 MHz reference clock, but making the code
safe against higher reference clocks seems like a reasoanble thing to
do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The p2 divider on VLV needs to be even when it's > 10. The current code
to make that happen is rather weird. Just make the step size adjustement
in the for loop decrement step.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite vlv_find_best_dpll() to use intel_clock_t rather than
an army of local variables.
Also extract the code to calculate the derived values into
vlv_clock().
v2: Split up the earlier fixes, extract vlv_clock()
v3: Initialize best_clock
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We do 'bestppm - 10' in vlv_find_best_dpll() but never check whether
that might underflow. Add such a check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use div_u64() to make the ppm calculation in vlv_find_best_dpll() safe
against interger overflows.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The interface uses an unsigned long, and we can use the unsigned counter
throughout our code, so do so. In the process, we notice one instance
where the shrink count is based on a heuristic rather than the result,
and another where we ask for too many pages to be purged.
v2: nr_to_scan needs to be promoted to a long as well, so just use
sc->nr_to_scan directly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we are waiting upon IO completion, inform the kernel through use
of the io_schedule() call rather than the regular schedule(). This
should allow the kernel to make better decisions regarding scheduling
and power management.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These checks should be ">=" instead of ">". j is used as an offset into
the table->mc_reg_address[] array and that has
SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE (16) elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
It should be ">=" instead of ">" here. The table->mc_reg_address[]
array has SMC_EVERGREEN_MC_REGISTER_ARRAY_SIZE (16) elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The error path does this:
for (--i; i >= 0; --i) {
which is a forever loop because "i" is unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Always use the regular UVD state for now. This fixes
a performance regression with UVD playback on certain APUs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the hw generated values rather than calculating
them in the driver. There may be some older r6xx
asics where this doesn't work correctly. This remains
to be seen.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The drm code that calculates the 1001 clocks rounds up
rather than truncating. This allows the table to match
properly on those modes.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Disable MSIs for now until we can fix them up
* nouveau/drm-nouveau-next:
drm/nouveau/mc: disable msi support by default, it's busted in tons of places
Commit 8b9ba7a3 'drm/gma500: use gem get/put page helpers' was missing a
line, which resulted in garbled screen.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Guillaume CLÉMENT <gclement@baobob.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The user of these counters was killed in
commit d79cdc8312
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Aug 8 15:41:32 2013 +0200
drm: no-op out GET_STATS ioctl
so clean up the leftovers as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can get the PCI vendor and device IDs via dev->pdev. So we can drop
the duplicated information.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The only user of ctx_count is the via driver, and we can replace that
use with list_is_singular().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
irq_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_vblank_init() is too ugly. Make it a bit easier on the eye by
collecting all the per-crtc vblank counters, timestamps etc. to
a structure and just allocate an array of those.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vblank_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vblank_disable_allowed is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_helper_probe_single_connector_modes() can be used to implement
->fill_modes(), not ->probe().
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the firmware is not builtin and userspace is not yet running, we can
stall the boot process for a minute whilst the firmware loader times
out. This is contrary to expectations of providing a builtin EDID!
In the process, we can rearrange the code to make the error handling
more resilient and prevent gcc warning about unitialised variables along
the error paths.
v2: Load builtins first, fix gcc second (Jani) and cosmetics (Ville).
v3: Verify that we do not read beyond the end of the fwdata (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Analog to drm_dev_register(), we now provide drm_dev_unregister() which
does the reverse. drm_dev_put() is still in place and combines the calls
to drm_dev_unregister() and drm_dev_free() so buses don't have to change.
*_get() and *_put() are used for reference-counting in the kernel.
However, drm_dev_put() definitely does not do any kind of ref-counting.
Hence, use the more appropriate *_register(), *_unregister(), *_alloc()
and *_free() names.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The error paths in DRM bus drivers currently leak memory as they don't
correctly revert drm_dev_alloc(). Introduce drm_dev_free() to free DRM
devices which haven't been registered, yet.
We must be careful not to introduce any side-effects with cleanups done in
drm_dev_free(). drm_ht_remove(), drm_ctxbitmap_cleanup() and
drm_gem_destroy() are all fine in that regard.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Try to keep all functions that handle DRM file_operations in drm_fops.c
so internal helpers can be marked static later.
This makes the split between the 3 core files more obvious:
- drm_stub.c: DRM device allocation/destruction and management
- drm_fops.c: DRM file_operations (except for ioctl)
- drm_drv.c: Global DRM init + ioctl handling
Well, ioctl handling is still spread throughout hundreds of source files,
but at least the others are clearly defined this way.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All bus drivers do device setup themselves. This requires us to adjust all
of them if we introduce new core features. Thus, merge all these into a
uniform drm_dev_register() helper.
Note that this removes the drm_lastclose() error path for AGP as it is
horribly broken. Moreover, no bus driver called this in any other error
path either. Instead, we use the recently introduced AGP cleanup helpers.
We also keep a DRIVER_MODESET condition around pci_set_drvdata() to keep
semantics.
[airlied: keep passing flags through so drivers don't oops on load]
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of managing device allocation+initialization in each bus-driver,
we should do that in a central place. drm_fill_in_dev() already does most
of it, but also requires the global drm lock for partial AGP device
registration.
Split both apart so we have a clean device initialization/allocation
phase, and a registration phase.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is no reason to keep the gem object separately allocated. nouveau is
the last user of gem_obj->driver_private, so if we embed it, we can get
rid of 8bytes per gem-object.
The implementation follows the radeon driver. bo->gem is only valid, iff
the bo was created via the gem helpers _and_ iff the user holds a valid
gem reference. That is, as the gem object holds a reference to the
nouveau_bo. If you use nouveau_ref() to gain a bo reference, you are not
guaranteed to also hold a gem reference. The gem object might get
destroyed after the last user drops the gem-ref via
drm_gem_object_unreference(). Use drm_gem_object_reference() to gain a
gem-reference.
For debugging, we can use bo->gem.filp != NULL to test whether a gem-bo is
valid. However, this shouldn't be used for real functionality to avoid
gem-internal dependencies.
Note that the implementation follows the previous style. However, we no
longer can check for bo->gem != NULL to test for a valid gem object. This
wasn't done before, so we should be safe now.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When booting with i915.fastboot=1, we always take tha code path and end
up undoing what we're trying to do with adjusted_mode.
Hopefully, as the fastboot hardware readout code is using adjusted_mode
as well, it should be equivalent.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of it just being on the mailing list, let's put Jesse's
explanation next to the code in question.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During system boot up, by default, the power gate for render, media and
display well still power gated. Normally, BIOS will turn off the power
gate. In the BIOS-less system, the driver need to turn off the power
gate very early during driver load.
v2: Move this to intel_uncore_sanitize to allow it to get call during
resume path. (Daniel)
v3: Remove redundant write 0 to DPIO_CTL, and use DPIO_RESET instead of
just 0x1 (Ville)
Add turn of power gate for display 2d/render well/media well.
v4: Remove toggle cmnreset in intel_uncore_sanitize. Cmnreset should
toggle after CRI clock source has been selected. Jesse DPIO reset patch
which toggle the cmnreset in intel_modeset_init_hw() should handle it.
(Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DPIO needs to have common reset de-asserted on soft resets like boot and
S3. In some cases, the BIOS will have done this for us, but it should
be safe to do at runtime as well, as long as we do it when the pipes are
otherwise off.
v2: update bit name to match docs better (Ville)
reset after CRI clock select (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69166
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
for igt test case.
v2: remove trailing spaces and fix conflicts
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet:
- make it comipile
- s/IS_HASWELL/HAS_PSR/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power Well in use forces constantly PSR to exit.
On recent Kernel I noticed that PSR Performance Counter was always 0
indicating that PSR was never really achieved.
By masking LPSP, PSR can work normally and save power on Haswell.
Two bugs had been raised with PSR flag enabled:
- "Screen flickers when booted by enabling PSR in the kernel (i915.enable_psr=1) , the system is booting to a gray screen."
- "When booting the DUT with PSR feature enabled in the kernel (i915.enable_psr=1) , the system is booting to a gray screen."
Both bugs has been fixed by this patch.
v2: proper comment for -fixes
Tested-by: Selvaraj, Elavarasan <elavarasanx.selvaraj@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After applying wait-boost we often find ourselves stuck at higher clocks
than required. The current threshold value requires the GPU to be
continuously and completely idle for 313ms before it is dropped by one
bin. Conversely, we require the GPU to be busy for an average of 90% over
a 84ms period before we upclock. So the current thresholds almost never
downclock the GPU, and respond very slowly to sudden demands for more
power. It is easy to observe that we currently lock into the wrong bin
and both underperform in benchmarks and consume more power than optimal
(just by repeating the task and measuring the different results).
An alternative approach, as discussed in the bspec, is to use a
continuous threshold for upclocking, and an average value for downclocking.
This is good for quickly detecting and reacting to state changes within a
frame, however it fails with the common throttling method of waiting
upon the outstanding frame - at least it is difficult to choose a
threshold that works well at 15,000fps and at 60fps. So continue to use
average busy/idle loads to determine frequency change.
v2: Use 3 power zones to keep frequencies low in steady-state mostly
idle (e.g. scrolling, interactive 2D drawing), and frequencies high
for demanding games. In between those end-states, we use a
fast-reclocking algorithm to converge more quickly on the desired bin.
v3: Bug fixes - make sure we reset adj after switching power zones.
v4: Tune - drop the continuous busy thresholds as it prevents us from
choosing the right frequency for glxgears style swap benchmarks. Instead
the goal is to be able to find the right clocks irrespective of the
wait-boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.
This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.
In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)
Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.
Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.
v2: Limit each client to receiving a single boost for each active period.
Tested by QA to only marginally increase power, and to demonstrably
increase throughput in games. No latency measurements yet.
v3: Cater for front-buffer rendering with manual throttling.
v4: Tidy up.
v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we switched to always using a timeout in conjunction with
wait_seqno, we lost the ability to detect missed interrupts. Since, we
have had issues with interrupts on a number of generations, and they are
required to be delivered in a timely fashion for a smooth UX, it is
important that we do log errors found in the wild and prevent the
display stalling for upwards of 1s every time the seqno interrupt is
missed.
Rather than continue to fix up the timeouts to work around the interface
impedence in wait_event_*(), open code the combination of
wait_event[_interruptible][_timeout], and use the exposed timer to
poll for seqno should we detect a lost interrupt.
v2: In order to satisfy the debug requirement of logging missed
interrupts with the real world requirments of making machines work even
if interrupts are hosed, we revert to polling after detecting a missed
interrupt.
v3: Throw in a debugfs interface to simulate broken hw not reporting
interrupts.
v4: s/EGAIN/EAGAIN/ (Imre)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Don't use the struct typedef in new code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We missed adding a few cleanup steps for recent additions.
Reviewer: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch attempts to clean up the ring/IA scaling programming in the
following ways.
1. Fix the comment about the DDR frequency. The math is 266MHz, not
133MHz. Formula was right, docs are wrong.
2. Mask the DCLK register since I don't know how it is defined on future
platforms.
3. use mult_frac instead of magic math.
This helps for future platform enabling.
v2: Actually use the right patch. The v1 was a mix of things, none of
which was right. Note that due to rounding, we actually get different
values (slightly higher) for the effective ring frequency.
v3: Use 1.25 instead of 1.33 as the original code did. (Jesse)
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we ever end up doing the retry loop due to bandwidth constraints, we
would rewrite pipe_src_{w,n} based on adjusted_mode timings. But by that
time the encoder may have already replaced the adjusted_mode with a
fixed panel mode, which would then corrupt pipe_src_{w,h}.
v2: Use requested_mode and slap on a big comment from Daniel
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This workaround is described in the mode set sequence documentation.
When enabling planes for the second pipe, we need to wait for 2
vblanks on the first pipe. This should solve "a flash of screen
corruption if planes are enabled on second/third pipe during the time
that big FIFO mode is exiting". Watermarks are fun :)
v2: Save indentation levels
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refactor the plane enabling/disabling into helper functions and move
the calls to happen as the first thing during .crtc_disable, and the
last thing during .crtc_enable.
Those are the two clear points where we are sure that the pipe is
actually running regardless of the encoder type or hardware
generation.
v2: Made by Paulo:
Remove the code touching everything but the Haswell functions. We
need this change on Haswell right now since it fixes a FIFO underrun
that we get on pipe A while we enable pipe B (see the workaround
notes on the Haswell mode set sequence documentation). We can bring
back the code to gens 2-7 later, once they're tested.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The global integrated clock source bit resides in DPLL B on VLV, but we
were treating it as a per-pipe resource. It needs to be set whenever
any PLL is active, so pull setting the bit out of vlv_update_pll and
into vlv_enable_pll. Also add a vlv_disable_pll to prevent disabling it
when pipe B shuts down.
I'm guessing on the references here, I expect this to bite any config
where multiple displays are active or displays are moved from pipe to
pipe.
v2: re-add bits in vlv_update_pll to keep from confusing the state checker
v3: use enum pipe checks (Daniel)
set CRI clock source early (Ville)
consistently set CRI clock source everywhere (Ville)
v4: drop unnecessary setting of bit in vlv enable pll (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67245
References: https://bugs.freedesktop.org/show_bug.cgi?id=69693
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/1/PIPE_B/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise using any atomic memory operation will lock up the GPU due
to a Haswell hardware bug.
v2: Use the _MASKED_BIT_ENABLE macro. Drop drm parameter definition.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: <stable@vger.kernel.org>
[danvet: Fix checkpatch fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During driver loading we are initializing rps.vlv_work in
valleyview_enable_rps() via the rps.delayed_resume_work delayed work.
This is too late since we are using vlv_work already via
i915_driver_load()->intel_uncore_sanitize()->
intel_disable_gt_powersave(). This at least leads to the following
kernel warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Fix this by initialzing vlv_work before we call intel_uncore_sanitize().
The regression was introduced in
commit 7dcd2677ea
Author: Konstantin Khlebnikov <khlebnikov@openvz.org>
Date: Wed Jul 17 10:22:58 2013 +0400
drm/i915: fix long-standing SNB regression in power consumption
after resume
though there was no good reason to initialize the static vlv_work from
another delayed work to begin with (especially since this will happen
multiple times).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69397
Tested-by: shui yangwei <yangweix.shui@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some reason, every single time I try to run module_reload
something tries to read the connector sysfs files. This happens
after we destroy the encoders and before we destroy the connectors, so
when the sysfs read triggers the connector detect() function,
intel_conector->encoder points to memory that was already freed.
The bad backtrace is just:
[<ffffffff8163ca9a>] dump_stack+0x54/0x74
[<ffffffffa00c2c8e>] intel_dp_detect+0x1e/0x4b0 [i915]
[<ffffffffa001913d>] status_show+0x3d/0x80 [drm]
[<ffffffff813d5340>] dev_attr_show+0x20/0x60
[<ffffffff81221f50>] ? sysfs_read_file+0x80/0x1b0
[<ffffffff81221f79>] sysfs_read_file+0xa9/0x1b0
[<ffffffff811aaf1e>] vfs_read+0x9e/0x170
[<ffffffff811aba4c>] SyS_read+0x4c/0xa0
[<ffffffff8164e392>] system_call_fastpath+0x16/0x1b
But if you add tons of memory checking debug options to your Kernel
you'll also see:
- general protection fault: 0000
- BUG kmalloc-4096 (Tainted: G D W ): Poison overwritten
- INFO: Allocated in intel_ddi_init+0x65/0x270 [i915]
- INFO: Freed in intel_dp_encoder_destroy+0x69/0xb0 [i915]
Among a bunch of other error messages.
So this commit just destroys the sysfs files before both the encoder
and connectors are freed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Neither the DP spec nor the compliance test spec state or imply that we
should write the DP_TRAINING_PATTERN_SET at every voltage swing and
pre-emphasis change. Indeed we probably shouldn't. So don't.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Smoke-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per DP1.2 spec.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It indicates a probable BIOS bug, but it appears to be harmless, and
there's nothing the user can do about it anyway, so reduce to a debug
msg. I've filed a bug with the BIOS folks about it anyway, so hopefully
they'll fix whatever GT SB read they were doing when the GT was off.
References: https://bugs.freedesktop.org/show_bug.cgi?id=69396
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The kernel shouldn't accept invalid modes, just say No.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the coding of stereo layout has changed from a bit field to an
enum, we need remove that check.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to use fewer bits in the mode structure, leaving room for
future work while allowing more stereo layouts types than we could have
ever dreamt of.
I also exposed the previously private DRM_MODE_FLAG_3D_MASK to set in
stone that we are using 5 bits for the stereo layout enum, reserving 32
values.
Even with that reservation, we gain 3 bits from the previous encoding.
The code adding the mandatory stereo modes needeed to be adapted as it was
relying or being able to or stereo layouts together.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to use the clock control reg to figure out how many CZ clks are in
30ns and use that as the basis for our RC6 residency calculations.
v2: use ULL everywhere for consistency (Chris)
factor out bias for clarity (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69692
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And add some reg defines while we're at it. Since the units of the RC6
residency counter are actually in CZ clocks, we want to just use the
high bits or we'll overflow too frequently.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_find_best_dpll() has an open coded DIV_ROUND_CLOSEST(). Replace it
with the real thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use 'continue' to get rid of one indent level in vlv_find_best_dpll()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CDCLK is used to generate the gmbus clock. This is normally done by
BIOS. Program the value if the BIOS-less system doesn't do it.
v2: Move this to intel_i2c_reset to allow reprogram the gmbus frequency
during resume. (Daniel)
v3: Change GMBUS_FREQ to GMBUSFREQ_VLV, and use VLV_DISPLAY_BASE.
(Ville).
Remove cdclk_ratio[] table, and calculate the cdclk ratio instead.
(Ville).
Change the shift then mask for reg read, to mask first, then shift.
(Ville).
Remove the gmbus frequency calculation = cdclk/1.01. Based on BIOS
programming, gmbus frequency = cdclk frequency. (Ville)
Add get_disp_clk_div, which can use to get cdclk/czclk divide.
v4: Fix the mmio_offset base for CZCLK_CDCLK_FREQ_RATIO, gmbus_freq
calculation, and duplicate check for gmbus_freq. (Ville)
In VLV, the spec is wrong about 4Mhz reference frequency for GMBUS. It
should be 1Mhz.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Add the comment Ville suggested. Also appease checkpatch a
bit.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Still digging up the actual VBT info for this, but wanted to get this
out there for testing, or in case others are also bugged by this.
This can happen if you boot with an external display connected. In that
case, the attached eDP backlight modulation frequency may not be
programmed, so we need to use something (in this case the value my BIOS
normally programs with just the internal display enabled).
v2: fix masking and magic value in read_blc_pwm_ctl (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67732
Tested-by: shui yangwei <yangweix.shui@intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we ask to adjust the crtc timings for stereo modes, the correct
pipe_src_w and pipe_src_h can be found in crtc_vdisplay and crtc_hdisplay.
v2: Add comment about why pipe_src_w/h need to be set afert
set_crtcinfo() (Daniel Vetter)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out big stereo buffers that are actually bigger that their
natural 2D counterpart, we need to blow up the crtc timings as well.
Not that this is only done for frame packing as this is the only stereo
mode currently exposed needing this kind of ajdustements.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to dump the parameters given to the hardware, so let's use
crtc_clock here.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some stereo modes, like frame packing, need a larger CRTC viewport than
the "natural" underlying 2D mode and thus drm_crtc_check_viewport()
needs to query the adjusted mode to use the correct h/vdisplay.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both setcrtc and page_flip are checking that the framebuffer is big
enough for the defined crtc viewport (x, y, hdisplay, vdisplay). Factor
that code out in a single function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using the frame packing and a single big framebuffer, some hardware
requires that we do everything like if we were scanning out the big
buffer itself. Let's instrument drm_mode_set_crtcinfo() to be able to do
this adjustement if the driver is asking for it.
v2: Use crtc_vtotal and multiply the clock by 2 instead of
reconstructing it (Ville Syrjälä)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like the various timings, make it possible to have a clock field
what we can tweak before giving it to hardware.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This field was only accessed by the nouveau driver, but never set. So
concluded we can rid of this one.
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like with interlaced or double scan modes, make stereo modes a
per-connector opt-in to give a chance to driver authors to make it work
before enabling it.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows to expose the alternate clock versions of the stereo modes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out a stereo mode, the AVI infoframe vic field has to be
the underlyng 2D VIC. Before that commit, we weren't matching the CEA
mode because of the extra stereo flag and then were setting the VIC
field in the AVI infoframe to 0.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out a 3D mode on HDMI, we need to send an HDMI infoframe
with the corresponding layout to the sink.
v2: Make s3d_structure_from_display_mode() less subtle (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When setting a stereo 3D mode, there can be only one bit set describing
the layout of the frambuffer(s). So reject invalid modes early.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we respect a nice design of having similar functions at the same
level, in this case:
do_hdmi_vsdb_modes()
- add_hdmi_mandatory_stereo_modes()
- add_hdmi_mode()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now, let's just look at the 3D_present flag of the CEA HDMI vendor
block to detect if the sink supports a small list of then mandatory 3D
formats.
See the HDMI 1.4a 3D extraction for detail:
http://www.hdmi.org/manufacturer/specification.aspx
v2: Rename freq to vrefresh, make the mandatory structure a bit more
compact, fix some white space issues and add a couple of const
(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This capability allows user space to control the delivery of modes with
the 3D flags set. This is to not play games with current user space
users not knowing anything about stereo 3D flags and that could try
to set a mode with one or several of those bits set.
So, the plan is to remove the stereo modes from the list of modes we
give to DRM clients by default, and let them through if we are being
told otherwise.
stereo_allowed is bound to the drm_file structure to make it a
per-client setting, not a global one.
v2: Replace clearing 3D flags by discarding the stereo modes now that
they are regular modes.
v3: SET_CAP -> SET_CLIENT_CAP rename (Chris Wilson)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This ioctl can be used to turn some knobs in a DRM driver. The client
can ask the DRM core for an alternate view of the reality: it can be
useful to be able to instruct the core that the DRM client can handle
new functionnality that would otherwise break current ABI.
v2: Rename to ioctl from SET_CAP to SET_CLIENT_CAP (Chris Wilson)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With some divider values we end up with the wrong result. So remove the
intermediates (like Ville suggested in the first place) to get the right
answer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calculation is a little different than other platforms.
v2: update to use port_clock instead
rebase on top of Ville's changes
v3: update to new port_clock semantics - don't divide by
pixel_multiplier (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67345
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that we can find the callers who introduce a ring stall. A single
ring stall is not too unwelcome, the right issue becomes when they start
to interlock and prevent any concurrent work. That, however, is a little
tricker to detect with a mere tracepoint!
v2: Rebrand it as a ring event, rather than an object event.
v3: Include the seqno in the tracepoint for posterity or something.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the missing cache-level to the describe_obj() function for debug and
error reporting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the typo in previous commit for DP 1.62 divisor.
drm/i915: Move Valleyview DP DPLL divisor calc to intel_dp_set_clock v2
v2: sigh, the m1 div is 3.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only wish to know the value of seqno when emitting the tracepoint, so
move the query from a parameter to the macro to inside the conditional
macro body so that the query is only evaluated when required.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though we track object activity and not VMA, because we have the
active_list be based on the VM, it makes the most sense to use VMAs in
the APIs.
NOTE: Daniel intends to eventually rip out active/inactive LRUs, but for
now, leave them be.
v2: Remove leftover hunk from the previous patch which didn't keep
i915_gem_object_move_to_active. That patch had to rely on the ring to
get the dev instead of the obj. (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"We do fairly often lookup the ggtt vma for an obj." - Chris Wilson. As
such, provide a function to offer slightly cheaper access to the vma.
Not performance tested. By my quick estimation it saves at least 3
pointer dereferences from the existing mechanism.
This patch mostly matches code from Chris in
<20130911221430.GB7825@nuc-i3427.alporthouse.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tracing vm eviction is really the event we care about. For the cases we
evict everything, we still will get the trace.
v2: Add the drm device to the trace since we might not be the only
device in the system. (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I already reorganized the header file, Daniel requested me to
remove those keywords. It seems "checkpath.pl --strict" also doesn't
like "extern" on header files.
At least now we're consistent :)
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions were added before the final PC8 implementation, and
their callers moved to intel_display.c during the code review.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And move it so it doesn't need a forward declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also move it to the top of the file so we can remove the forward
declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel complained that we keep adding stuff to the bottom of the file,
so we constantly have conflicts. So reorganize everything and split
them file-by-file, also sorting the files in alphabetical order. This
way, patches touching different files will have a smaller chance of
conflicting. Of course, this commit will conflict with everybody on
the list :)
Also remove a few useless comments and make some things fit into 80
lines.
v2: - Conflict with intel_ddi_get_config
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not valid for later non-PCH split platforms such as VLV.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Call intel_ddi_get_config() to get the pipe_bpp settings from
DDI.
The sync polarity settings from DDI are irrelevant for CRT
output, so override them with data from the ADPA register.
v2: Extract intel_crt_get_flags()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69691
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Flat out skip anything to do with PLL if we have a DSI encoder (and thus
DSI PLL). Also skip PLL computation if the encoder has already set
clocks. This allows for some tidying up of the code, including a
superfluous call to intel_limit() for LVDS downclock path.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During SDVO initialisation it would be useful to a have a record of the
individual devices we try to enable and later probe - in particular to
be able to see which fail.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Obtaining the forcwake requires expensive and time consuming
serialisation. And we often try to obtain the forcewake multiple times
in very quick succession. We can reduce the overhead of these sequences
by delaying the forcewake release, and so not hammer the hw quite so
hard.
I was hoping this would help with the spurious
[drm:__gen6_gt_force_wake_mt_get] *ERROR* Timed out waiting for forcewake old ack to clear.
found on Haswell. Alas not.
v2: Fix teardown ordering - unmap the regs after turning off forcewake,
and make sure we do turn off forcewake - both found by Ville.
v3: As we introduce intel_uncore_fini(), use it to make sure everything
is disabled before we hand back to the BIOS.
Note: I have no claims for improved performance, stablity or power
comsumption for this patch. We should not be hitting the registers often
enough for this to improve benchmarks, but given the nature of our hw it
is likely to improve long term stability.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The | operation has higher precedence than "?:" so the macro always
returns GT_RENDER_L3_PARITY_ERROR_INTERRUPT_S1.
This regression has been introduce in "drm/i915: Add second slice l3
remapping".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i9xx_crtc_clock_get() no longer populates adjusted_mode.clock, so we
must get the pixel clock from port_clock in intel_crtc_mode_get().
This bug caused Chris's 845g machine to lockup during boot, and it
was introduced in:
commit 18442d0878
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 13 16:00:08 2013 +0300
drm/i915: Fix port_clock and adjusted_mode.clock readout all over
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69713
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Future generations will be changing these registers (thanks to design
for giving us an early heads up). To help abstract, create the
definition of the base of the register block, and define all registers
relative to that.
Design has promised to not change the offsets relative to the base.
v2: Also change IS_HASWELL checks to HAS_PSR
CC: Rodrigo Vivi <rodrigo.vivi@gmail.com>
CC: Intel GFX <intel-gfx@lists.freedesktop.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reduce AUX transactions for non-eDP.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already restore planes during the modeset operation, so no need to do
another loop over the planes and try to restore them again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Call intel_uncore_early_sanitize() first thing during resume to prevent
stale BIOS leftovers from being reported as unclaimed register access.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_restore_state() -> i915_restore_display() will attempt to
re-disable VGA during resume. So the power well needs to be powered on
before that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_modeset_init() will already attempt to disable VGA. In order to do
that, it needs the power well to be on. So move the power well init
to happen before intel_modeset_init() during driver load.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The VGA plane needs to be disabled before we start doing any
modeset operations on resume.
This should also guarantee that the power well will be enabled
when we call i915_redisable_vga() since it gets explicitly powered on
during resume, and will get powered back off during the modeset
operation if no longer needed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VGA registers live inside the power well on HSW, so in order to write
the VGA MSR register we need the power well to be on.
We really must write to the register to properly clear the
VGA_MSR_MEM_EN enable bit, even if all VGA registers get zeroed when
the power well is down. It seems that the implicit zeroing done by
the power well is not enough to propagate the VGA_MSR_MEM_EN bit to
whomever is actually responsible for the memory decode ranges.
If we leave VGA memory decode enabled, and then turn off the power well,
all VGA memory reads will return zeroes. But if we first disable VGA
memory deocde and then turn off the power well, VGA memory reads
return all ones, indicating that the access wasn't claimed by anyone.
For the vga arbiter to function correctly the IGD must not claim the
VGA memory accesses.
Previously we were doing the VGA_MSR register access while the power well
was excplicitly powered up during driver init. But ever since
commit 6e1b4fdad5
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 5 20:40:52 2013 +0300
drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done
we delay the VGA memory disable until fbcon has initialized, and so
there's a possibility that the power well got turned off during the
fbcon modeset. Also vgacon_save_screen() will need the power well to be
on to be able to read the VGA memory.
So immediately after enabling the power well during init grab a refence
for VGA purposes, and after all the VGA handling is done, release it.
v2: Add intel_display_power_put() for the num_pipes==0 case
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix up the patch wiggle screw-up that I've done and which
Paulo catched. Also polish spelling in the patch headline.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It only controls the setting of the vbt.edp_support variable, which in
turn only controls one debug output plus can also force-disable the
lvds output.
Since the value only restricted this logic to mobile ilk there's the
slight risk that this will break lvds on desktop ilk or on snb/ivb
platforms. But with the vbt it's better when we know what's going on
here, so let's rip it out and see what happens.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no reason to init a DP connector if the encoder just supports
HDMI: we'll just waste hundreds and hundreds of cycles trying to do DP
AUX transactions to detect if there's something there. Same goes for a
DP connector that doesn't support HDMI, but I'm not sure these
actually exist.
v2: - Use bit fields
- Remove useless identation level
- Replace DRM_ERROR with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our code makes a lot of assumptions regarding what each DDI port
actually supports, and the VBT should tell us what is really happening
in the hardware. So parse the information provided by the VBT and
check if any of our assumptions is wrong.
Our driver also has a history of not really trusting the VBT, so a
WARN here could mean that:
a) our coding assumptions are wrong
b) the VBT is wrong
c) we're incorrectly parsing the VBT
d) the checks are wrong
But I really hope we won't ever trigger any of those WARNs.
v2: Don't check the redundant "Capabilities" field from byte 24 since
it doesn't seem to be used.
v3: Rebase
v4: Replace WARN with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our code currently assumes that port X will use the DP AUX channel X
and the DDC pin X. The VBT should tell us how things are mapped, so
add some WARNs in case we discover our assumptions are wrong (or in
case the VBT is just wrong, which is also perfectly possible).
Why would someone wire port B to AUX C and DDC D?
v2: Rebase
v3: Convert WARNs to DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently use the recommended values from BSpec, but the VBT
specifies the correct value to use for the hardware we have, so use
it. We also fall back to the recommended value in case we can't find
the VBT.
In addition, this code also provides some infrastructure to parse more
information about the DDI ports. There's a lot more information we
could extract and use in the future.
v2: - Move some code to init_vbt_defaults.
v3: - Rebase
- Clarify the "DVO Port" matching code
v4: - Use I915_MAX_PORTS
- Change the HAS_DDI checks
- Replace DRM_ERROR with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently treat the child_device_config as a simple struct, but
this is not correct: new BDB versions change the meaning of some
offsets, so the struct needs to be adjusted for each version.
Since there are too many changes (today we're in version 170!), making
a big versioned union would be too complicated, so child_device_config
is now a union of 3 things: (i) a "raw" byte array that's safe to use
anywhere; (ii) an "old" structure that's the one we've been using and
should be safe to keep in the SDVO and TV code; and (iii) a "common"
structure that should contain only fields that are common for all the
known VBT versions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never took the lock ourselves and all callers expect the struct_mutex
to be locked upon return (be it success or error), thereore dropping the
lock along the error paths looks to be a vestigial error from
commit db1b76ca6a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 9 16:51:37 2013 +0200
drm/i915: don't frob mm.suspended when not using ums
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's actually no real risk since we already check for stricter
constraints earlier (using UINT_MAX / sizeof (struct
drm_i915_gem_exec_object2) as the limit). But in eb_create we use
signed integers, which steals a factor of 2. Luckily struct
drm_i915_gem_exec_object2 for this to not matter.
Still, be consistent and use unsigned integers.
Similar use unsinged integers when checking for overflows in the
relocation entry processing.
I've also added a new subtests to igt/gem_reloc_overflow to also
test for overflowing args->buffer_count values.
v2: Give the variables again tighter scope to make it clear that the
computation is purely local and doesn't leak out to the 2nd block.
Requested by Chris Wilson.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the gratious overallocation of crtcs. Seems to go back to the ums
days of yonder ...
We also still need it to make the fbdev emulation happy, but I don't
think there's really a need. Especially since the current fbdev
emulation doesn't actually support cloning.
v2: Use sizeof(*pointer) pattern (Jani).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No buffer overflows here, but better safe than sorry.
v2:
- Fixup the sizeof conversion, I've missed the pointer deref (Jani).
- Drop the redundant GFP_ZERO, kcalloc alreads memsets (Jani).
- Use kmalloc_array for the execbuf fastpath to avoid the memset
(Chris). I've opted to leave all other conversions as-is since they
aren't in a fastpath and dealing with cleared memory instead of
random garbage is just generally nicer.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the contentious kmalloc_array hunk in execbuf.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done while reviewing all our allocations for fubar. Also a few errant
cases of lacking () for the sizeof operator - just a bit of OCD.
I've left out all the conversions that also should use kcalloc from
this patch (it's only 2).
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Return -ENOMEM if the allocation fails.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
None of the DP DPCD helpers need to modify the DPCD.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We have some code duplication related to EDID duplication. Add a helper.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We haven't read the downstream port caps for DPCD 1.0, so don't use
them.
v2: use defines for DPCD 1.0 downstream port types
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm-intel-next-2013-09-21:
- clock state handling rework from Ville
- l3 parity handling fixes for hsw from Ben
- some more watermark improvements from Ville
- ban badly behaved context from Mika
- a few vlv improvements from Jesse
- VGA power domain handling from Ville
drm-intel-next-2013-09-06:
- Basic mipi dsi support from Jani. Not yet converted over to drm_bridge
since that was too fresh, but the porting is in progress already.
- More vma patches from Ben, this time the code to convert the execbuffer
code. Now that the shrinker recursion bug is tracked down we can move
ahead here again. Yay!
- Optimize hw context switching to not generate needless interrupts (Chris
Wilson). Also some shuffling for the oustanding request allocation.
- Opregion support for SWSCI, although not yet fully wired up (we need a
bit of runtime D3 support for that apparently, due to Windows design
deficiencies), from Jani Nikula.
- A few smaller changes all over.
[airlied: merge conflict fix in i9xx_set_pipeconf]
* tag 'drm-intel-next-2013-09-21-merged' of git://people.freedesktop.org/~danvet/drm-intel: (119 commits)
drm/i915: assume all GM45 Acer laptops use inverted backlight PWM
drm/i915: cleanup a min_t() cast
drm/i915: Pull intel_init_power_well() out of intel_modeset_init_hw()
drm/i915: Add POWER_DOMAIN_VGA
drm/i915: Refactor power well refcount inc/dec operations
drm/i915: Add intel_display_power_{get, put} to request power for specific domains
drm/i915: Change i915_request power well handling
drm/i915: POSTING_READ IPS_CTL before waiting for the vblank
drm/i915: don't disable ERR_INT on the IRQ handler
drm/i915/vlv: disable rc6p and rc6pp residency reporting on BYT
drm/i915/vlv: honor i915_enable_rc6 boot param on VLV
drm/i915: s/HAS_L3_GPU_CACHE/HAS_L3_DPF
drm/i915: Do remaps for all contexts
drm/i915: Keep a list of all contexts
drm/i915: Make l3 remapping use the ring
drm/i915: Add second slice l3 remapping
drm/i915: Fix HSW parity test
drm/i915: dump crtc timings from the pipe config
drm/i915: register backlight device also when backlight class is a module
drm/i915: write D_COMP using the mailbox
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Pull drm fixes from Dave Airlie:
"Nothing too major, radeon still has some dpm changes for off by
default.
Radeon, intel, msm:
- radeon: a few more dpm fixes (still off by default), uvd fixes
- i915: runtime warn backtrace and regression fix
- msm: iommu changes fallout"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (27 commits)
drm/msm: use drm_gem_dumb_destroy helper
drm/msm: deal with mach/iommu.h removal
drm/msm: Remove iommu include from mdp4_kms.c
drm/msm: Odd PTR_ERR usage
drm/i915: Fix up usage of SHRINK_STOP
drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
drm/i915: preserve pipe A quirk in i9xx_set_pipeconf
drm/i915/tv: clear adjusted_mode.flags
drm/i915/dp: increase i2c-over-aux retry interval on AUX DEFER
drm/radeon/cik: fix overflow in vram fetch
drm/radeon: add missing hdmi callbacks for rv6xx
drm/i915: Use a temporary va_list for two-pass string handling
drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
drm/radeon: disable tests/benchmarks if accel is disabled
drm/radeon: don't set default clocks for SI when DPM is disabled
drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
drm/radeon/dpm: fetch the max clk from voltage dep tables helper
...
A small fix + deal with fallout of iommu changes + use new
drm_gem_dumb_destroy helper.
* 'msm-fixes-3.12-rc2' of git://people.freedesktop.org/~robclark/linux:
drm/msm: use drm_gem_dumb_destroy helper
drm/msm: deal with mach/iommu.h removal
drm/msm: Remove iommu include from mdp4_kms.c
drm/msm: Odd PTR_ERR usage
We still need an API exported by msm iommu driver (but not visible in
any public header anymore). For now, just declare the prototype
ourselves, but when msm iommu driver provides a better option, use that
instead.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The include file has been removed and the file does not
need it anyway, so remove it. Fixes a compile error.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The variable priv->kms is not initialized yet.
Found by "scripts/coccinelle/tests/odd_ptr_err.cocci".
PTR_ERR should access the value just tested by IS_ERR.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
More radeon fixes for 3.12. Kind of all over the place: UVD, DPM,
tiling, etc.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
drm/radeon/cik: fix overflow in vram fetch
drm/radeon: add missing hdmi callbacks for rv6xx
drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
drm/radeon: disable tests/benchmarks if accel is disabled
drm/radeon: don't set default clocks for SI when DPM is disabled
drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
drm/radeon/dpm: fetch the max clk from voltage dep tables helper
drm/radeon: fix missed variable sized access
drm/radeon: Make r100_cp_ring_info() and radeon_ring_gfx() safe (v2)
drm/radeon/cik: Add tiling mode index for 1D tiled depth/stencil surfaces
drm/radeon/cik: Fix encoding of number of banks in tiling configuration info
drm/radeon/cik: Fix printing of client name on VM protection fault
drm/radeon: additional gcc fixes for radeon_atombios.c
drm/radeon: avoid UVD corruption on AGP cards using GPU gart
In
commit 81e49f8114
Author: Glauber Costa <glommer@openvz.org>
Date: Wed Aug 28 10:18:13 2013 +1000
i915: bail out earlier when shrinker cannot acquire mutex
SHRINK_STOP was added to tell the core shrinker code to bail out and
go to the next shrinker since the i915 shrinker couldn't acquire
required locks. But the SHRINK_STOP return code was added to the
->count_objects callback and not the ->scan_objects callback as it
should have been, resulting in tons of dmesg noise like
shrink_slab: i915_gem_inactive_scan+0x0/0x9c negative objects to delete nr=-xxxxxxxxx
Fix discusssed with Dave Chinner.
References: http://www.spinics.net/lists/intel-gfx/msg33597.html
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Glauber Costa <glommer@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This regression has been introduced in
commit 9f11a9e4e5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 13 00:54:58 2013 +0200
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
Ville brough up the idea that this is just the pipe A quirk gone
wrong.
Note that after resume the bios might or might not have enabled pipe A
already. We have a bit of magic to make sure that on resume we set up
a decent mode for pipe A, but I fear if I just smash pipe A to always
on we'd enable it in a bogus state and hang the hw. Hence the
readback.
v2: Clarify the logic a bit as suggested by Chris. Also amend the
commit message to clarify why we don't unconditionally enable the
pipe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66462
References: https://lkml.org/lkml/2013/8/26/238
Cc: Meelis Roos <mroos@ut.ee>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use |= instead of = as suggested by Chris.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The native TV encoder has it's own flags to adjust sync modes and
enabled interlaced modes which are totally irrelevant for the adjusted
mode. This worked out nicely since the input modes used by both the
load detect code and reported in the ->get_modes callbacks all have no
flags set, and we also don't fill out any of them in the ->get_config
callback.
This changed with the additional sanitation done with
commit 2960bc9cce
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Jul 30 13:36:32 2013 +0300
drm/i915: make user mode sync polarity setting explicit
sinc now the "no flags at all" state wouldn't fit through core code
any more. So fix this up again by explicitly clearing the flags in the
->compute_config callback.
Aside: We have zero checking in place to make sure that the requested
mode is indeed the right input mode we want for the selected TV mode.
So we'll happily fall over if userspace tries to pull us. But that's
definitely work for a different patch series. So just add a FIXME
comment for now.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no clear cut rules or specs for the retry interval, as there
are many factors that affect overall response time. Increase the
interval, and even more so on branch devices which may have limited i2c
bit rates.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=60263
Tested-by: Nicolas Suzor <nic@suzor.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix a bug that was introduced in commit c4c11dd160 ("drm/i2c: tda998x:
add video and audio input configuration") when Sebastian cleaned up my
original patch. Without this being fixed, audio is muted when the
display is turned off, never to be re-enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Darren Etheridge <detheridge@ti.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Missing ULL when calculating the amount of vram
leads to an overflow when the amount of vram is >= 4G.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When dpm was merged, I added a new asic struct for
rv6xx, but it never got properly updated when the
hdmi callbacks were added due to the two patch sets
being developed in parallel.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69729
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
In
commit edc3d8848d
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu May 23 13:55:35 2013 +0300
drm/i915: avoid big kmallocs on reading error state
we introduce a two-pass mechanism for splitting long strings being
formatted into the error-state. The first pass finds the length, and the
second pass emits the right portion of the string into the accumulation
buffer. Unfortunately we use the same va_list for both passes, resulting
in the second pass reading garbage off the end of the argument list. As
the two passes are only used for boundaries between read() calls, the
corruption is only rarely seen.
This fixes the root cause behind
commit baf27f9b17
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Jun 29 23:26:50 2013 +0100
drm/i915: Break up the large vsnprintf() in print_error_buffers()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMORAAoJEHm+PkMAQRiGj14H/1bjhtfNjPdX7MVQAzA+WpwX
s7h1IQu2Si9S5S1lBiM2sBTOssVcmfheO9x4yqm7JNOD1RnssWKOM3q+zVOLstwd
GD3gluJPeraD5EyYSqEJ9ILPQ3gbxb4wOlT0Z291TW6E8XhLRr0RTOJPksRsgvLH
Ckm9uJh6ArS6ZXfXiaDQfd+xHAQJkUfW6nMSA0g9ZO9C6KIDRvcbUmrY3m4HhfIk
mK0TXCBs+AXGDIjTEB8JgIQL/5y1Qn0c4R+2uTU/4YWwyLvJTV1e44kGoleukMMT
6Pw/TNlUEN161dbSaqCyF3sfXHDYQ5valycI2PDgitMtPSxbzsU1VDizS8+daRg=
=lEmF
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc2' into drm-intel-next
Backmerge Linux 3.12-rc2 to prep for a bunch of -next patches:
- Header cleanup in intel_drv.h, both changed in -fixes and my current
-next pile.
- Cursor handling cleanup for -next which depends upon the cursor
handling fix merged into -rc2.
All just trivial conflicts of the "changed adjacent lines" type:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting with UVD3 message and feedback buffers have their
own 256MB segment, so no need to force them into VRAM any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The tests are only usable if the acceleration engines have
been successfully initialized.
Based on an initial patch from: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This is a partial revert of c6cf7777a3.
We need to take into account the clk voltage dependencies of the
board. Not doing so can lead to stability issues on certain
boards if the clks exceed the levels in the dep tables.
DPM already takes that into account, so for optimal performance,
use DPM.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds a helper function to fetch the max clock
from the voltage clock dependecy tables. Clocks above that
level tend to be unstable and will require additional driver
tweaks in order to work properly.
This patch implemented the helper function to fetch the max clocks
from the dependency tables. The following patches implement the
per-asic clock filtering.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I missed this when I fixed up this file.
Noticed-by: Mathias Fröhlich <Mathias.Froehlich@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull drm fixes from Dave Airlie:
- some small fixes for msm and exynos
- a regression revert affecting nouveau users with old userspace
- intel pageflip deadlock and gpu hang fixes, hsw modesetting hangs
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
Revert "drm: mark context support as a legacy subsystem"
drm/i915: Don't enable the cursor on a disable pipe
drm/i915: do not update cursor in crtc mode set
drm/exynos: fix return value check in lowlevel_buffer_allocate()
drm/exynos: Fix address space warnings in exynos_drm_fbdev.c
drm/exynos: Fix address space warning in exynos_drm_buf.c
drm/exynos: Remove redundant OF dependency
drm/msm: drop unnecessary set_need_resched()
drm/i915: kill set_need_resched
drm/msm: fix potential NULL pointer dereference
drm/i915/dvo: set crtc timings again for panel fixed modes
drm/i915/sdvo: Robustify the dtd<->drm_mode conversions
drm/msm: workaround for missing irq
drm/msm: return -EBUSY if bo still active
drm/msm: fix return value check in ERR_PTR()
drm/msm: fix cmdstream size check
drm/msm: hangcheck harder
drm/msm: handle read vs write fences
drm/i915/sdvo: Fully translate sync flags in the dtd->mode conversion
drm/i915: Use proper print format for debug prints
...
The lower layers of sysfs will not allow an "offset" of more than
GEN7_L3LOG_SIZE and also l3_access_valid() caps it a second time. But
it's a little easier to audit if we don't have to worry that the
subtraction will result in negative values.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The init and resume codepaths want to handel the power well in slightly
different ways, so pull the power well init out from
intel_modeset_init_hw() which gets called in both cases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VGA registers/memory live inside the the display power well. Add a power
domain for VGA.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We increase/decrease the power well refcount in several places now, and
all of those places need to do the same thing, so pull that code into
a few small helper functions.
v2: Rename the funcs to __intel_power_well_{get,put}
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add APIs to get/put power well references for specific purposes.
v2: Split the i915_request change to another patch
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reorganize the internal i915_request power well handling to use the
reference count just like everyone else. This way all we need to do is
check the reference count and we know whether the power well needs to be
enabled of disabled.
v2: Split he intel_display_power_{get,put} change to another patch.
Add intel_resume_power_well() to make sure we enable the power
well on resume
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent NULL pointer dereference in case when radeon_ring_fini() did it's job.
Reading of r100_cp_ring_info and radeon_ring_gfx debugfs entries will lead to a KP if ring buffer was deallocated, e.g. on failed ring test.
Seen on PA-RISC machine having "radeon: ring test failed (scratch(0x8504)=0xCAFEDEAD)" issue.
v2: agd5f: add some parens around ring->ready check
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There are multiple valid values, not just 0 or 1. Required
to properly support 2D tiling in the userspace drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The string is encoded from the MSB to the LSB of the register.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the user has forced the driver to use the internal GPU gart
rather than AGP on an AGP card, force the buffers to vram
as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Dieter Nützel <Dieter@nuetzel-hh.de>
Cc: stable@vger.kernel.org
Make sure we write to IPS before we actually wait.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently disable the ERR_INT interrupts while running the IRQ
handler because we fear that if we do an unclaimed register access
from inside the IRQ handler we'll keep triggering the IRQ handler
forever.
The problem is that since we always disable the ERR_INT interrupts at
the IRQ handler, when we get a FIFO underrun we'll always print both
messages:
- "uncleared fifo underrun on pipe A"
- "Pipe A FIFO underrun"
Because the "was_enabled" variable from
ivybridge_set_fifo_underrun_reporting will always be false (since we
disable ERR int at the IRQ handler!).
Instead of actually fixing ivybridge_set_fifo_underrun_reporting,
let's just remove the "disable ERR_INT during the IRQ handler" code.
As far as we know we shouldn't really be triggering ERR_INT interrupts
from the IRQ handler, so if we ever get stuck in the endless loop of
interrupts we can git-bisect and revert (and we can even bisect and
revert this patch in case I'm just wrong). As a bonus, our IRQ handler
is now simpler and a few nanoseconds faster.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Byt doesn't have rc6p and rc6pp support and even more important the
the offsets of the residency registers there's something else. So Just
return a constant 0 to avoid upsetting userspace tools like powertop.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Explain a bit in the commit message what's going on.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disabling it isn't really an option on these platforms, but having it
available for power comparisons is useful.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A couple small msm fixes. Plus drop of set_need_resched().
* 'msm-fixes-3.12' of git://people.freedesktop.org/~robclark/linux:
drm/msm: drop unnecessary set_need_resched()
drm/msm: fix potential NULL pointer dereference
drm/msm: workaround for missing irq
drm/msm: return -EBUSY if bo still active
drm/msm: fix return value check in ERR_PTR()
drm/msm: fix cmdstream size check
drm/msm: hangcheck harder
drm/msm: handle read vs write fences
Just small fixes, and code cleanups.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: fix return value check in lowlevel_buffer_allocate()
drm/exynos: Fix address space warnings in exynos_drm_fbdev.c
drm/exynos: Fix address space warning in exynos_drm_buf.c
drm/exynos: Remove redundant OF dependency
Some more dealock fixes around pageflips and gpu hangs, fixes for hsw hangs
when doing modesets/dpms. And a few minor things to rectify issues with our
modeset state tracking which the checker spotted.
* tag 'drm-intel-fixes-2013-09-19' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Don't enable the cursor on a disable pipe
drm/i915: do not update cursor in crtc mode set
drm/i915: kill set_need_resched
drm/i915/dvo: set crtc timings again for panel fixed modes
drm/i915/sdvo: Robustify the dtd<->drm_mode conversions
drm/i915/sdvo: Fully translate sync flags in the dtd->mode conversion
drm/i915: Use proper print format for debug prints
drm/i915: fix wait_for_pending_flips vs gpu hang deadlock
drm/i915: Track pfit enable state separately from size
This reverts commit 7c510133d9.
Well looks like not enough digging was done, libdrm_nouveau before 2.4.33
used contexts,
292da616fe1f936ca78a3fa8e1b1b19883e343b6 nouveau: pull in major libdrm rewrite
got rid of them,
Reported-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We'd only ever used this define to denote whether or not we have the
dynamic parity feature (DPF) and never to determine whether or not L3
exists. Baytrail is a good example of where L3 exists, and not DPF.
This patch provides clarify in the code for future use cases which might
want to actually query whether or not L3 exists.
v2: Add /* DPF == dynamic parity feature */
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On both Ivybridge and Haswell, row remapping information is saved and
restored with context. This means, we never actually properly supported
the l3 remapping because our sysfs interface is asynchronous (and not
tied to any context), and the known faulty HW would be reused by the
next context to run.
Not that due to the asynchronous nature of the sysfs entry, there is no
point modifying the registers for the existing context. Instead we set a
flag for all contexts to load the correct remapping information on the
next run. Interested clients can use debugfs to determine whether or not
the row has been remapped.
One could propose at this point that we just do the remapping in the
kernel. I guess since we have to maintain the sysfs interface anyway,
I'm not sure how useful it is, and I do like keeping the policy in
userspace; (it wasn't my original decision to make the
interface the way it is, so I'm not attached).
v2: Force a context switch when we have a remap on the next switch.
(Ville)
Don't let userspace use the interface with disabled contexts.
v3: Don't force a context switch, just let it nop
Improper context slice remap initialization, 1<<1 instead of 1<<i, but I
rewrote it to avoid a second round of confusion.
Error print moved to error path (All Ville)
Added a comment on why the slice remap initialization happens.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I have implemented this patch before without creating a separate list
(I'm having trouble finding the links, but the messages ids are:
<1364942743-6041-2-git-send-email-ben@bwidawsk.net>
<1365118914-15753-9-git-send-email-ben@bwidawsk.net>)
However, the code is much simpler to just use a list and it makes the
code from the next patch a lot more pretty.
As you'll see in the next patch, the reason for this is to be able to
specify when a context needs to get L3 remapping. More details there.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using LRI for setting the remapping registers allows us to stream l3
remapping information. This is necessary to handle per context remaps as
we'll see implemented in an upcoming patch.
Using the ring also means we don't need to frob the DOP clock gating
bits.
v2: Add comment about lack of worry for concurrent register access
(Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Bikeshed the comment a bit by doing a s/XXX/Note - there's
nothing to fix.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Certain HSW SKUs have a second bank of L3. This L3 remapping has a
separate register set, and interrupt from the first "slice". A slice is
simply a term to define some subset of the GPU's l3 cache. This patch
implements both the interrupt handler, and ability to communicate with
userspace about this second slice.
v2: Remove redundant check about non-existent slice.
Change warning about interrupts of unknown slices to WARN_ON_ONCE
Handle the case where we get 2 slice interrupts concurrently, and switch
the tracking of interrupts to be non-destructive (all Ville)
Don't enable/mask the second slice parity interrupt for ivb/vlv (even
though all docs I can find claim it's rsvd) (Ville + Bryan)
Keep BYT excluded from L3 parity
v3: Fix the slice = ffs to be decremented by one (found by Ville). When
I initially did my testing on the series, I was using 1-based slice
counting, so this code was correct. Not sure why my simpler tests that
I've been running since then didn't pick it up sooner.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell changed the log registers to be WO, so we can no longer read
them to determine the programming (which sucks, see later note). For
now, simply use the cached value, and hope HW doesn't screw us over.
v2: Simplify the logic to avoid an extra !, remove last, and fix the
buffer offset which broke along the rebase (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57441
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I always get royally confused how a modeline with all zeros could
possible pass the paranoid pipe config checker. Until I realize again
that we only check the crtc timings. So dump the crtc timings for the
adjusted mode.
This will be even more important for 3D support where the crtc timings
are markedly different from the input modeline if we have
frame-by-frame 3d output enabled.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville and I were wondering why his laptop was missing the
intel_backlight sysfs interface. Turns out we never register it when
CONFIG_BACKLIGHT_CLASS_DEVICE=m. This has been broken ever since the
i915 native backlight interface was added.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
You can't write it using the MCHBAR mirror, the write will just get
dropped.
This should make us BSpec-compliant, but there's no real bug I could
reproduce that is fixed by this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix spelling mistake in the comment that Damien spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm radeon/nouveau/core fixes from Dave Airlie:
"Mostly radeon fixes, with some nouveau bios parser, ttm fix and a fix
for AST driver"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
drm/fb-helper: don't sleep for screen unblank when an oops is in progress
drm, ttm Fix uninitialized warning
drm/ttm: fix the tt_populated check in ttm_tt_destroy()
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
drm/radeon: avoid UVD corruptions on AGP cards
drm/radeon: fix panel scaling with eDP and LVDS bridges
drm/radeon/dpm: rework auto performance level enable
drm/radeon: Fix hmdi typo
drm/radeon/dpm/rs780: fix force_performance state for same sclks
drm/radeon/dpm/rs780: don't enable sclk scaling if not required
drm/radeon/dpm/rs780: add some sanity checking to sclk scaling
drm/radeon/dpm/rs780: use drm_mode_vrefresh()
drm/udl: rip out set_need_resched
drm/ast: fix the ast open key function
drm/radeon/dpm: add bapm callback for kb/kv
drm/radeon/dpm: add bapm callback for trinity
drm/radeon/dpm: add infrastructure to properly handle bapm
...
Otherwise the system will burn even brighter and worse, leave the user
wondering what's going on exactly.
Since we already have a panic handler which will (try) to restore the
entire fbdev console mode, we can just bail out. Inspired by a patch from
Konstantin Khlebnikov. The callchain leading to this, cut&pasted from
Konstantin's original patch:
callstack:
panic()
bust_spinlocks(1)
unblank_screen()
vc->vc_sw->con_blank()
fbcon_blank()
fb_blank()
info->fbops->fb_blank()
drm_fb_helper_blank()
drm_fb_helper_dpms()
drm_modeset_lock_all()
mutex_lock(&dev->mode_config.mutex)
Note that the entire locking in the fb helper around panic/sysrq and kdbg
is ... non-existant. So we have a decent change of blowing up
everything. But since reworking this ties in with funny concepts like the
fbdev notifier chain or the impressive things which happen around
console_lock while oopsing, I'll leave that as an exercise for braver
souls than me.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix uninitialized warning.
drivers/gpu/drm/ttm/ttm_object.c: In function ‘ttm_base_object_lookup’:
drivers/gpu/drm/ttm/ttm_object.c:213:10: error: ‘base’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
kref_put(&base->refcount, ttm_release_base);
^
drivers/gpu/drm/ttm/ttm_object.c:221:26: note: ‘base’ was declared here
struct ttm_base_object *base;
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After a vmalloc failure in ttm_dma_tt_alloc_page_directory(),
ttm_dma_tt_init() will call ttm_tt_destroy() to cleanup, and end up
inside the driver's unpopulate() hook when populate() has never yet
been called.
On nouveau, the first issue to be hit because of this is that
dma_address[] may be a NULL pointer. After working around this,
ttm_pool_unpopulate() may potentially hit the same issue with
the pages[] array.
It seems to make more sense to avoid calling unpopulate on already
unpopulated TTMs than to add checks to all the implementations.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: stable@vger.kernel.org
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A couple of bios parser fixes (one for ancient chips, another for new ones - important in Optimus configs). Another to make sure KMS is enabled on certain Optimus configs, and a TTM failure path fix.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
On HSW enabling a plane on a disabled pipe may hang the entire system.
And there's no good reason for doing it ever, so just don't.
v2: Move the crtc active checks to intel_crtc_cursor_{set,move} to
avoid confusing people during modeset
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor is disabled before crtc mode set in crtc disable (and we
assert this is the case), and enabled afterwards in crtc enable. Do not
update it in crtc mode set.
On HSW enabling a plane on a disabled pipe may hang the entire system.
And there's no good reason for doing it ever, so just don't.
v2: Add note about HSW hangs - vsyrjala
Cc: stable@vger.kernel.org
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sometimes I see the "non asle set request??" message on my Haswell
machine, so I decided to get the spec and see if some bits are missing
from the mask. We do have some bits missing from the mask, so this
patch adds them, and the corresponding code to print "unsupported"
messages just like we do with the other bits we don't support.
But I still see the "non asle set request??" message on my machine :(
Also use the proper ASLC name to indicate the registers we're talking
about.
v2: - Properly set the new FAILED bits
- Rename the old FAILED bits
- Print everything we don't support
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reduces dmesg noise when there's a glitch on the hpd line, or there
are more than one connectors on the same hpd line and only one of them
changes.
While at it, switch to use the friendly status names instead of numbers.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far we control everything and nothing exceeds the current limits,
but (i) we never think about these limits when reviewing patches, (ii)
not all the callers check the return values and (iii) if we ever hit
any of these messages, we'll have to fix the code that added the bad
message.
The current limit for these messages is 20 since we only have 5 data
registers on all the current gens.
The checks inside intel_dp_aux_native_{write,read} are to prevent
buffer overflows. The check inside intel_dp_aux_ch is to prevent
writing past our 5 data registers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Double wide mode is only available on pipe A, except on GDG where
pipe B is also double wide capable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pipe horizontal source size must be even when either LVDS dual channel
mode, DVO ganged mode, or pipe double wide mode is used.
We must round it down since we can never increase the user specified
viewport size.
The actual error from an odd pipe source width looks like a diagonal
shift, like you might get from a bad stride.
v2: s/ganaged/ganged/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want to try to push the hardware beyond it's capabilities,
so check the pixel clock against the display core clock limit. Do
it for pre-gen4 for now since that's where we alread have the double
wide pixel clock limit check.
Let's assume that when double wide mode is enabled the max
pixel clock limit is also doubled.
FIXME: panel fitter downscaling probably affects the limit on
non-pch platforms too, so we'd need another version of
ilk_pipe_pixel_rate() to figure that out.
FIXME: should check the limits on all platforms. Also sprites
affect the max allowed pixel rate on some platforms, so we need
to eventually tie all the planes and pipes into one check in
the future. But we need plane state pre-compute before that can
happen.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read the double wide pipe information from hardware in
i9xx_get_pipe_config(), and check it in intel_pipe_config_compare()
For gen4+ double_wide is always false so the comparison can be done
on all platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine the need for double wide mode already in compute_config
stage as we need that information to figure out if horizontal
coordinates need to be adjusted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simply inline the 100MHz default we're using. Having gunk around that
has leftover LVDS support on a platform that just doesn't have this
isn't of any use.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First of all we should not be looking at fb->{width,height} as those do
not tell us what the actual pipe size is. Second of all we need to use
>= for the comparison.
So fix the comparison, and make use of the new pipe_src_{w,h} to
determine the real pipe source dimensions.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the cursor x coordinate is exactly -cursor_width, the cursor is
invisible. And obviously the same holds for the y coordinate and
cursor_height.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to clarify the purpose of requested_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Especially intel_gmch_panel_fitting was shifting way too much over the
right edge and also was way too long. So extract two helpers, one for
gen4+ and one for gen2/3. Now the entire thing is again almost
readable ...
Spurred by checkpatch freaking out about a Ville's pipeconfig rework
in intel_panel.c
Otherwise just two lines that needed appropriate breaking.
Not functional change in this patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather that mess about with hdisplay/vdisplay from requested_mode, add
explicit pipe src size information to pipe config.
Now requested_mode is only really relevant for dvo/sdvo output timings.
For everything else either adjusted_mode or pipe src size should be
used.
In many places where we end up using pipe source size, we should
actually use the primary plane size, but we don't currently store
that information explicitly. As long as we treat primaries as full
screen only, we can get away with this. Eventually when we move
primaries over to drm_plane, we need to fix it all up.
v2: Add a comment to explain what pipe_src_{w,h} are
Add a note about primary planes to commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
adjusted_mode contains our real timings, not requested_mode. Use the
correct thing in DSI PLL code.
Also constify adjusted_mode since we don't change it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than dig up the pipe source size from crtc->mode, use
intel_crtc->config.requested_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.
intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().
v2: Copy paste a big comment from danvet's mail explaining
when we can ditch the extra checks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_edp_psr_match_conditions() currently looks at crtc->mode
when it really needs to look at adjusted_mode. Fix it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The clock in crtc->mode doesn't necessarily mean anything. Let's look
at the clock in adjusted_mode instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently most of the watermark code looks at crtc->mode which is the
user requested mode. The only piece of information there that is
relevant is hdisplay, the rest must come from adjusted_mode. Convert
all of the code to use requested_mode and adjusted_mode from
pipe config appropriately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the mode flags from the adjusted_mode, not user requested mode.
The hdisplay/vdisplay check actually checkes the primary plane size,
so those still need to come from the user requested mode.
Extract both modes from pipe config instead of the drm_crtc.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
