The arm64 MMU supports a Contiguous bit which is a hint that the TTE
is one of a set of contiguous entries which can be cached in a single
TLB entry. Supporting this bit adds new intermediate huge page sizes.
The set of huge page sizes available depends on the base page size.
Without using contiguous pages the huge page sizes are as follows.
4KB: 2MB 1GB
64KB: 512MB
With a 4KB granule, the contiguous bit groups together sets of 16 pages
and with a 64KB granule it groups sets of 32 pages. This enables two new
huge page sizes in each case, so that the full set of available sizes
is as follows.
4KB: 64KB 2MB 32MB 1GB
64KB: 2MB 512MB 16GB
If a 16KB granule is used then the contiguous bit groups 128 pages
at the PTE level and 32 pages at the PMD level.
If the base page size is set to 64KB then 2MB pages are enabled by
default. It is possible in the future to make 2MB the default huge
page size for both 4KB and 64KB granules.
Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com>
Reviewed-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: David Woods <dwoods@ezchip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The pmuserenr_el0 register value is architecturally UNKNOWN on reset.
Current kernel code resets that register value iff the core pmu device is
correctly probed in the kernel. On platforms with missing DT pmu nodes (or
disabled perf events in the kernel), the pmu is not probed, therefore the
pmuserenr_el0 register is not reset in the kernel, which means that its
value retains the reset value that is architecturally UNKNOWN (system
may run with eg pmuserenr_el0 == 0x1, which means that PMU counters access
is available at EL0, which must be disallowed).
This patch adds code that resets pmuserenr_el0 on cold boot and restores
it on core resume from shutdown, so that the pmuserenr_el0 setup is
always enforced in the kernel.
Cc: <stable@vger.kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In systems with three levels of cache(PoU at L1 and PoC at L3),
PoC cache flush instructions flushes L2 and L3 caches which could affect
performance.
For cache flushes for I and D coherency, PoU should suffice.
So changing all I and D coherency related cache flushes to PoU.
Introduced a new __clean_dcache_area_pou API for dcache flush till PoU
and provided a common macro for __flush_dcache_area and
__clean_dcache_area_pou.
Also, now in __sync_icache_dcache, icache invalidation for non-aliasing
VIPT icache is done only for that particular page instead of the earlier
__flush_icache_all.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ashok Kumar <ashoks@broadcom.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In paging_init, we allocate the zero page, memset it to zero and then
point TTBR0 to it in order to avoid speculative fetches through the
identity mapping.
In order to guarantee that the freshly zeroed page is indeed visible to
the page table walker, we need to execute a dsb instruction prior to
writing the TTBR.
Cc: <stable@vger.kernel.org> # v3.14+, for older kernels need to drop the 'ishst'
Signed-off-by: Will Deacon <will.deacon@arm.com>
We drop __cpu_setup in .text.init, which ends up being part of .text.
The .text.init section was a legacy section name which has been unused
elsewhere for a long time.
The ".text.init" name is misleading if read as a synonym for
".init.text". Any CPU may execute __cpu_setup before turning the MMU on,
so it should simply live in .text.
Remove the pointless section assignment. This will leave __cpu_setup in
the .text section.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently we treat the alternatives separately from other data that's
only used during initialisation, using separate .altinstructions and
.altinstr_replacement linker sections. These are freed for general
allocation separately from .init*. This is problematic as:
* We do not remove execute permissions, as we do for .init, leaving the
memory executable.
* We pad between them, making the kernel Image bianry up to PAGE_SIZE
bytes larger than necessary.
This patch moves the two sections into the contiguous region used for
.init*. This saves some memory, ensures that we remove execute
permissions, and allows us to remove some code made redundant by this
reorganisation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As pgd_offset{,_k} shift the input address by PGDIR_SHIFT, the sub-page
bits will always be shifted out. There is no need to apply PAGE_MASK
before this.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Take the new memblock attribute MEMBLOCK_NOMAP into account when
deciding whether a certain region is or should be covered by the
kernel direct mapping.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
These functions/variables are not needed after booting, so mark them
as __init or __initdata.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Callees of __create_mapping may decide to create section mappings if
sufficient low bits of the physical and virtual addresses they were
passed are zero. While __create_mapping rounds the virtual base address
down, it does not similarly round the physical base address down, and
hence non-zero bits in the physical address can prevent use of a section
mapping, even where a whole next-level table would be used instead.
Round down the physical base address in __create_mapping to enable all
callees to always create section mappings when such a mapping is
possible.
Cc: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If a caller of __create_mapping provides a PA and VA which have
different sub-page offsets, it is not clear which offset they expect to
apply to the mapping, and is indicative of a bad caller.
In some cases, the region we wish to map may validly have a sub-page
offset in the physical and virtual addresses. For example, EFI runtime
regions have 4K granularity, yet may be mapped by a 64K page kernel. So
long as the physical and virtual offsets are the same, the region will
be mapped at the expected VAs.
Disallow calls with differing sub-page offsets, and WARN when they are
encountered, so that we can detect and fix such cases.
Cc: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This reverts commit 348a65cdcb.
Incorrect page table manipulation that does not respect the ARM ARM
recommended break-before-make sequence may lead to TLB conflicts. The
contiguous PTE patch makes the system even more susceptible to such
errors by changing the mapping from a single page to a contiguous range
of pages. An additional TLB invalidation would reduce the risk window,
however, the correct fix is to switch to a temporary swapper_pg_dir.
Once the correct workaround is done, the reverted commit will be
re-applied.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Under some unusual context-switching patterns, it is possible to end up
with multiple threads from the same mm running concurrently with
different ASIDs:
1. CPU x schedules task t with mm p containing ASID a and generation g
This task doesn't block and the CPU doesn't context switch.
So:
* per_cpu(active_asid, x) = {g,a}
* p->context.id = {g,a}
2. Some other CPU generates an ASID rollover. The global generation is
now (g + 1). CPU x is still running t, with no context switch and
so per_cpu(reserved_asid, x) = {g,a}
3. CPU y schedules task t', which shares mm p with t. The generation
mismatches, so we take the slowpath and hit the reserved ASID from
CPU x. p is then updated so that p->context.id = {g + 1,a}
4. CPU y schedules some other task u, which has an mm != p.
5. Some other CPU generates *another* CPU rollover. The global
generation is now (g + 2). CPU x is still running t, with no context
switch and so per_cpu(reserved_asid, x) = {g,a}.
6. CPU y once again schedules task t', but now *fails* to hit the
reserved ASID from CPU x because of the generation mismatch. This
results in a new ASID being allocated, despite the fact that t is
still running on CPU x with the same mm.
Consequently, TLBIs (e.g. as a result of CoW) will not be synchronised
between the two threads.
This patch fixes the problem by updating all of the matching reserved
ASIDs when we hit on the slowpath (i.e. in step 3 above). This keeps
the reserved ASIDs in-sync with the mm and avoids the problem.
Reported-by: Tony Thompson <anthony.thompson@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We are missing descriptions for some valid xFSC values in the fault info
table (e.g. "TLB conflict abort"), and have erroneous descriptions for
reserved values (e.g. "asynchronous external abort", "debug event").
This patch adds the missing xFSC values, and removes erroneous decoding
of values reserved by the architecture, as described in ARM DDI 0487A.h.
At the same time, fixed the unbalanced brackets for the synchronous
parity error strings in the table.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In early_alloc we check if the memblock_alloc failed by checking
the virtual address of the result, which will never fail. This patch
fixes it to check the actual result for failure.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The permissions in mark_rodata_ro trigger a build error
with STRICT_MM_TYPECHECKS. Fix this by introducing
PAGE_KERNEL_ROX for the same reasons as PAGE_KERNEL_RO.
From Ard:
"PAGE_KERNEL_EXEC has PTE_WRITE set as well, making the range
writeable under the ARMv8.1 DBM feature, that manages the
dirty bit in hardware (writing to a page with the PTE_RDONLY
and PTE_WRITE bits both set will clear the PTE_RDONLY bit in that case)"
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Including linux/acpi.h from asm/dma-mapping.h causes tons of compile-time
warnings, e.g.
drivers/isdn/mISDN/dsp_ecdis.h:43:0: warning: "FALSE" redefined
drivers/isdn/mISDN/dsp_ecdis.h:44:0: warning: "TRUE" redefined
drivers/net/fddi/skfp/h/targetos.h:62:0: warning: "TRUE" redefined
drivers/net/fddi/skfp/h/targetos.h:63:0: warning: "FALSE" redefined
However, it looks like the dependency should not even there as
I do not see why __generic_dma_ops() cares about whether we have
an ACPI based system or not.
The current behavior is to fall back to the global dma_ops when
a device has not set its own dma_ops, but only for DT based systems.
This seems dangerous, as a random device might have different
requirements regarding IOMMU or coherency, so we should really
never have that fallback and just forbid DMA when we have not
initialized DMA for a device.
This removes the global dma_ops variable and the special-casing
for ACPI, and just returns the dma ops that got set for the
device, or the dummy_dma_ops if none were present.
The original code has apparently been copied from arm32 where we
rely on it for ISA devices things like the floppy controller, but
we should have no such devices on ARM64.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[catalin.marinas@arm.com: removed acpi_disabled check in arch_setup_dma_ops()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When booting a 64k pages kernel that is built with CONFIG_DEBUG_RODATA
and resides at an offset that is not a multiple of 512 MB, the rounding
that occurs in __map_memblock() and fixup_executable() results in
incorrect regions being mapped.
The following snippet from /sys/kernel/debug/kernel_page_tables shows
how, when the kernel is loaded 2 MB above the base of DRAM at 0x40000000,
the first 2 MB of memory (which may be inaccessible from non-secure EL1
or just reserved by the firmware) is inadvertently mapped into the end of
the module region.
---[ Modules start ]---
0xfffffdffffe00000-0xfffffe0000000000 2M RW NX ... UXN MEM/NORMAL
---[ Modules end ]---
---[ Kernel Mapping ]---
0xfffffe0000000000-0xfffffe0000090000 576K RW NX ... UXN MEM/NORMAL
0xfffffe0000090000-0xfffffe0000200000 1472K ro x ... UXN MEM/NORMAL
0xfffffe0000200000-0xfffffe0000800000 6M ro x ... UXN MEM/NORMAL
0xfffffe0000800000-0xfffffe0000810000 64K ro x ... UXN MEM/NORMAL
0xfffffe0000810000-0xfffffe0000a00000 1984K RW NX ... UXN MEM/NORMAL
0xfffffe0000a00000-0xfffffe00ffe00000 4084M RW NX ... UXN MEM/NORMAL
The same issue is likely to occur on 16k pages kernels whose load
address is not a multiple of 32 MB (i.e., SECTION_SIZE). So round to
SWAPPER_BLOCK_SIZE instead of SECTION_SIZE.
Fixes: da141706ae ("arm64: add better page protections to arm64")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The iommu-dma layer does its own size-alignment for coherent DMA
allocations based on IOMMU page sizes, but we still need to consider
CPU page sizes for the cases where a non-cacheable CPU mapping is
created. Whilst everything on the alloc/map path seems to implicitly
align things enough to make it work, some functions used by the
corresponding unmap/free path do not, which leads to problems freeing
odd-sized allocations. Either way it's something we really should be
handling explicitly, so do that to make both paths suitably robust.
Reported-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- __cmpxchg_double*() return type fix to avoid truncation of a long to
int and subsequent logical "not" in cmpxchg_double() misinterpreting
the operation success/failure
- BPF fixes for mod and div by zero
- Fix compilation with STRICT_MM_TYPECHECKS enabled
- VDSO build fix without libgcov
- Some static and __maybe_unused annotations
- Kconfig clean-up (FRAME_POINTER)
- defconfig update for CRYPTO_CRC32_ARM64
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ApkD
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes and clean-ups from Catalin Marinas:
"Here's a second pull request for this merging window with some
fixes/clean-ups:
- __cmpxchg_double*() return type fix to avoid truncation of a long
to int and subsequent logical "not" in cmpxchg_double()
misinterpreting the operation success/failure
- BPF fixes for mod and div by zero
- Fix compilation with STRICT_MM_TYPECHECKS enabled
- VDSO build fix without libgcov
- Some static and __maybe_unused annotations
- Kconfig clean-up (FRAME_POINTER)
- defconfig update for CRYPTO_CRC32_ARM64"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: suspend: make hw_breakpoint_restore static
arm64: mmu: make split_pud and fixup_executable static
arm64: smp: make of_parse_and_init_cpus static
arm64: use linux/types.h in kvm.h
arm64: build vdso without libgcov
arm64: mark cpus_have_hwcap as __maybe_unused
arm64: remove redundant FRAME_POINTER kconfig option and force to select it
arm64: fix R/O permissions of FDT mapping
arm64: fix STRICT_MM_TYPECHECKS issue in PTE_CONT manipulation
arm64: bpf: fix mod-by-zero case
arm64: bpf: fix div-by-zero case
arm64: Enable CRYPTO_CRC32_ARM64 in defconfig
arm64: cmpxchg_dbl: fix return value type
split_pud and fixup_executable are only called from within mmu.c, so
they can be declared static.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The mapping permissions of the FDT are set to 'PAGE_KERNEL | PTE_RDONLY'
in an attempt to map the FDT as read-only. However, not only does this
break at build time under STRICT_MM_TYPECHECKS (since the two terms are
of different types in that case), it also results in both the PTE_WRITE
and PTE_RDONLY attributes to be set, which means the region is still
writable under ARMv8.1 DBM (and an attempted write will simply clear the
PT_RDONLY bit).
So instead, define PAGE_KERNEL_RO (which already has an established
meaning across architectures) and use that instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The new page table code that manipulates the PTE_CONT flags does so
in a way that is inconsistent with STRICT_MM_TYPECHECKS. Fix it by
using the correct combination of __pgprot() and pgprot_val().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
__GFP_WAIT was renamed for __GFP_RECLAIM and the gfpflags_allow_blocking()
helper was added.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This time including:
* A new IOMMU driver for s390 pci devices
* Common dma-ops support based on iommu-api for ARM64. The plan is to
use this as a basis for ARM32 and hopefully other architectures as
well in the future.
* MSI support for ARM-SMMUv3
* Cleanups and dead code removal in the AMD IOMMU driver
* Better RMRR handling for the Intel VT-d driver
* Various other cleanups and small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=jLlB
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"This time including:
- A new IOMMU driver for s390 pci devices
- Common dma-ops support based on iommu-api for ARM64. The plan is
to use this as a basis for ARM32 and hopefully other architectures
as well in the future.
- MSI support for ARM-SMMUv3
- Cleanups and dead code removal in the AMD IOMMU driver
- Better RMRR handling for the Intel VT-d driver
- Various other cleanups and small fixes"
* tag 'iommu-updates-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/vt-d: Fix return value check of parse_ioapics_under_ir()
iommu/vt-d: Propagate error-value from ir_parse_ioapic_hpet_scope()
iommu/vt-d: Adjust the return value of the parse_ioapics_under_ir
iommu: Move default domain allocation to iommu_group_get_for_dev()
iommu: Remove is_pci_dev() fall-back from iommu_group_get_for_dev
iommu/arm-smmu: Switch to device_group call-back
iommu/fsl: Convert to device_group call-back
iommu: Add device_group call-back to x86 iommu drivers
iommu: Add generic_device_group() function
iommu: Export and rename iommu_group_get_for_pci_dev()
iommu: Revive device_group iommu-ops call-back
iommu/amd: Remove find_last_devid_on_pci()
iommu/amd: Remove first/last_device handling
iommu/amd: Initialize amd_iommu_last_bdf for DEV_ALL
iommu/amd: Cleanup buffer allocation
iommu/amd: Remove cmd_buf_size and evt_buf_size from struct amd_iommu
iommu/amd: Align DTE flag definitions
iommu/amd: Remove old alias handling code
iommu/amd: Set alias DTE in do_attach/do_detach
iommu/amd: WARN when __[attach|detach]_device are called with irqs enabled
...
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWOkmIAAoJEGvWsS0AyF7x4GgQAINU3NePjFFvWZNCkqobeH9+
jFKwtXamIudhTSdnXNXyYWmtRL9Krg3qI4zDQf68dvDFAZAze2kVuOi1yPpCbpFZ
/j/afNyQc7+PoyqRAzmT+EMPZlcuOA84Prrl1r3QWZ58QaFeVk/6ZxrHunTHxN0x
mR9PIXfWx73MTo+UnG8FChkmEY6LmV4XpemgTaMR9FqFhdT51OZSxDDAYXOTm4JW
a5HdN9OWjjJ2rhLlFEaC7tszG9B5doHdy2tr5ge/YERVJzIPDogHkMe8ZhfAJc+x
SQU5tKN6Pg4MOi+dLhxlk0/mKCvHLiEQ5KVREJnt8GxupAR54Bat+DQ+rP9cSnpq
dRQTcARIOyy9LGgy+ROAsSo+NiyM5WuJ0/WJUYKmgWTJOfczRYoZv6TMKlwNOUYb
tGLCZHhKPM3yBHJlWbQykl3xmSuudxCMmjlZzg7B+MVfTP6uo0CRSPmYl+v67q+J
bBw/Z2RYXWYGnvlc6OfbMeImI6prXeE36+5ytyJFga0m+IqcTzRGzjcLxKEvdbiU
pr8n9i+hV9iSsT/UwukXZ8ay6zH7PrTLzILWQlieutfXlvha7MYeGxnkbLmdYcfe
GCj374io5cdImHcVKmfhnOMlFOLuOHphl9cmsd/O2LmCIqBj9BIeNH2Om8mHVK2F
YHczMdpESlJApE7kUc1e
=3six
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
arm64/efi: fix libstub build under CONFIG_MODVERSIONS
ARM64: Enable multi-core scheduler support by default
arm64/efi: move arm64 specific stub C code to libstub
arm64: page-align sections for DEBUG_RODATA
arm64: Fix build with CONFIG_ZONE_DMA=n
arm64: Fix compat register mappings
arm64: Increase the max granular size
arm64: remove bogus TASK_SIZE_64 check
arm64: make Timer Interrupt Frequency selectable
arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
arm64: cachetype: fix definitions of ICACHEF_* flags
arm64: cpufeature: declare enable_cpu_capabilities as static
genirq: Make the cpuhotplug migration code less noisy
arm64: Constify hwcap name string arrays
arm64/kvm: Make use of the system wide safe values
arm64/debug: Make use of the system wide safe value
arm64: Move FP/ASIMD hwcap handling to common code
arm64/HWCAP: Use system wide safe values
arm64/capabilities: Make use of system wide safe value
arm64: Delay cpu feature capability checks
...
Trying to build with CONFIG_ZONE_DMA=n leaves visible references
to the now-undefined ZONE_DMA, resulting in a syntax error.
Hide the references behind an #ifdef instead of using IS_ENABLED.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The <linux/mm.h> already provides the PAGE_ALIGNED macro. Let's
use this macro instead of IS_ALIGNED and passing PAGE_SIZE directly.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Acked-by: Laura Abbott <laura@labbott.name>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
At the moment we run through the arm64_features capability list for
each CPU and set the capability if one of the CPU supports it. This
could be problematic in a heterogeneous system with differing capabilities.
Delay the CPU feature checks until all the enabled CPUs are up(i.e,
smp_cpus_done(), so that we can make better decisions based on the
overall system capability. Once we decide and advertise the capabilities
the alternatives can be applied. From this state, we cannot roll back
a feature to disabled based on the values from a new hotplugged CPU,
due to the runtime patching and other reasons. So, for all new CPUs,
we need to make sure that they have the established system capabilities.
Failing which, we bring the CPU down, preventing it from turning online.
Once the capabilities are decided, any new CPU booting up goes through
verification to ensure that it has all the enabled capabilities and also
invokes the respective enable() method on the CPU.
The CPU errata checks are not delayed and is still executed per-CPU
to detect the respective capabilities. If we ever come across a non-errata
capability that needs to be checked on each-CPU, we could introduce them via
a new capability table(or introduce a flag), which can be processed per CPU.
The next patch will make the feature checks use the system wide
safe value of a feature register.
NOTE: The enable() methods associated with the capability is scheduled
on all the CPUs (which is the only use case at the moment). If we need
a different type of 'enable()' which only needs to be run once on any CPU,
we should be able to handle that when needed.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com>
[catalin.marinas@arm.com: static variable and coding style fixes]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch turns on the 16K page support in the kernel. We
support 48bit VA (4 level page tables) and 47bit VA (3 level
page tables).
With 16K we can map 128 entries using contiguous bit hint
at level 3 to map 2M using single TLB entry.
TODO: 16K supports 32 contiguous entries at level 2 to get us
1G(which is not yet supported by the infrastructure). That should
be a separate patch altogether.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We use section maps with 4K page size to create the swapper/idmaps.
So far we have used !64K or 4K checks to handle the case where we
use the section maps.
This patch adds a new symbol, ARM64_SWAPPER_USES_SECTION_MAPS, to
handle cases where we use section maps, instead of using the page size
symbols.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With iommu_dma_ops in place, hook them up to the configuration code, so
IOMMU-fronted devices will get them automatically.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Taking some inspiration from the arch/arm code, implement the
arch-specific side of the DMA mapping ops using the new IOMMU-DMA layer.
Since there is still work to do elsewhere to make DMA configuration happen
in a more appropriate order and properly support platform devices in the
IOMMU core, the device setup code unfortunately starts out carrying some
workarounds to ensure it works correctly in the current state of things.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Sparse reports some new issues introduced by the kasan patches:
arch/arm64/mm/kasan_init.c:91:13: warning: no previous prototype for
'kasan_early_init' [-Wmissing-prototypes] void __init kasan_early_init(void)
^
arch/arm64/mm/kasan_init.c:91:13: warning: symbol 'kasan_early_init'
was not declared. Should it be static? [sparse]
This patch resolves the problem by adding a prototype for
kasan_early_init and marking the function as asmlinkage, since it's only
called from head.S.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds arch specific code for kernel address sanitizer
(see Documentation/kasan.txt).
1/8 of kernel addresses reserved for shadow memory. There was no
big enough hole for this, so virtual addresses for shadow were
stolen from vmalloc area.
At early boot stage the whole shadow region populated with just
one physical page (kasan_zero_page). Later, this page reused
as readonly zero shadow for some memory that KASan currently
don't track (vmalloc).
After mapping the physical memory, pages for shadow memory are
allocated and mapped.
Functions like memset/memmove/memcpy do a lot of memory accesses.
If bad pointer passed to one of these function it is important
to catch this. Compiler's instrumentation cannot do this since
these functions are written in assembly.
KASan replaces memory functions with manually instrumented variants.
Original functions declared as weak symbols so strong definitions
in mm/kasan/kasan.c could replace them. Original functions have aliases
with '__' prefix in name, so we could call non-instrumented variant
if needed.
Some files built without kasan instrumentation (e.g. mm/slub.c).
Original mem* function replaced (via #define) with prefixed variants
to disable memory access checks for such files.
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This will be used by KASAN latter.
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For more control over which functions are called with the MMU off or
with the UEFI 1:1 mapping active, annotate some assembler routines as
position independent. This is done by introducing ENDPIPROC(), which
replaces the ENDPROC() declaration of those routines.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With 64k pages, the next larger segment size is 512M. The linux
kernel also uses different protection flags to cover its code and data.
Because of this requirement, the vast majority of the kernel code and
data structures end up being mapped with 64k pages instead of the larger
pages common with a 4k page kernel.
Recent ARM processors support a contiguous bit in the
page tables which allows the a TLB to cover a range larger than a
single PTE if that range is mapped into physically contiguous
ram.
So, for the kernel its a good idea to set this flag. Some basic
micro benchmarks show it can significantly reduce the number of
L1 dTLB refills.
Add boot option to enable/disable CONT marking, as well as fix a
bug found by Steve Capper.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
[catalin.marinas@arm.com: remove CONFIG_ARM64_CONT_PTE altogether]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The kernel page dump utility needs to be aware of the CONT bit before
it will break up pages ranges for display.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
mm_cpumask isn't actually used for anything on arm64, so remove all the
code trying to keep it up-to-date.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
switch_mm performs some checks to try and avoid entering the ASID
allocator:
(1) If we're switching to the init_mm (no user mappings), then simply
set a reserved TTBR0 value with no page table (the zero page)
(2) If prev == next *and* the mm_cpumask indicates that we've run on
this CPU before, then we can skip the allocator.
However, there is plenty of redundancy here. With the new ASID allocator,
if prev == next, then we know that our ASID is valid and do not need to
worry about re-allocation. Consequently, we can drop the mm_cpumask check
in (2) and move the prev == next check before the init_mm check, since
if prev == next == init_mm then there's nothing to do.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Our current switch_mm implementation suffers from a number of problems:
(1) The ASID allocator relies on IPIs to synchronise the CPUs on a
rollover event
(2) Because of (1), we cannot allocate ASIDs with interrupts disabled
and therefore make use of a TIF_SWITCH_MM flag to postpone the
actual switch to finish_arch_post_lock_switch
(3) We run context switch with a reserved (invalid) TTBR0 value, even
though the ASID and pgd are updated atomically
(4) We take a global spinlock (cpu_asid_lock) during context-switch
(5) We use h/w broadcast TLB operations when they are not required
(e.g. in flush_context)
This patch addresses these problems by rewriting the ASID algorithm to
match the bitmap-based arch/arm/ implementation more closely. This in
turn allows us to remove much of the complications surrounding switch_mm,
including the ugly thread flag.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There are a number of places where a single CPU is running with a
private page-table and we need to perform maintenance on the TLB and
I-cache in order to ensure correctness, but do not require the operation
to be broadcast to other CPUs.
This patch adds local variants of tlb_flush_all and __flush_icache_all
to support these use-cases and updates the callers respectively.
__local_flush_icache_all also implies an isb, since it is intended to be
used synchronously.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When cold-booting a CPU, we must invalidate any junk entries from the
local TLB prior to enabling the MMU. This doesn't require broadcasting
within the inner-shareable domain, so de-scope the operation to apply
only to the local CPU.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This is the arm64 portion of commit 45cac65b0f ("readahead: fault
retry breaks mmap file read random detection"), which was absent from
the initial port and has since gone unnoticed. The original commit says:
> .fault now can retry. The retry can break state machine of .fault. In
> filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
> try, since the page is in page cache now, ra->mmap_miss is decreased. And
> these are done in one fault, so we can't detect random mmap file access.
>
> Add a new flag to indicate .fault is tried once. In the second try, skip
> ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
With this change, Mark reports that:
> Random read improves by 250%, sequential read improves by 40%, and
> random write by 400% to an eMMC device with dm crypto wrapped around it.
Cc: Shaohua Li <shli@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Riley Andrews <riandrews@android.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If CMA is turned on and CMA size is set to zero, kernel should
behave as if CMA was not enabled at compile time.
Every dma allocation should check existence of cma area
before requesting memory.
Arm has done this by commit e464ef16c4 ("arm: dma-mapping: add
checking cma area initialized"), also do this for arm64.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We don't want to expose the DCC to userspace, particularly as there is
a kernel console driver for it.
This patch resets mdscr_el1 to disable userspace access to the DCC
registers on the cold boot path.
Signed-off-by: Will Deacon <will.deacon@arm.com>
UEFI spec 2.5 section 2.3.6.1 defines that
EFI_MEMORY_[UC|WC|WT|WB] are possible EFI memory types for
AArch64.
Each of those EFI memory types is mapped to a corresponding
AArch64 memory type. So we need to define PROT_DEVICE_nGnRnE
and PROT_NORMWL_WT additionaly.
MT_NORMAL_WT is defined, and its encoding is added to MAIR_EL1
when initializing the CPU.
Signed-off-by: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438936621-5215-6-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The arm64 booting document requires that the bootloader has cleaned the
kernel image to the PoC. However, when a CPU re-enters the kernel due to
either a CPU hotplug "on" event or resuming from a low-power state (e.g.
cpuidle), the kernel text may in-fact be dirty at the PoU due to things
like alternative patching or even module loading.
Thanks to I-cache speculation with the MMU off, stale instructions could
be fetched prior to enabling the MMU, potentially leading to crashes
when executing regions of code that have been modified at runtime.
This patch addresses the issue by ensuring that the local I-cache is
invalidated immediately after a CPU has enabled its MMU but before
jumping out of the identity mapping. Any stale instructions fetched from
the PoC will then be discarded and refetched correctly from the PoU.
Patching kernel text executed prior to the MMU being enabled is
prohibited, so the early entry code will always be clean.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since __get_dma_pgprot() does The Right Thing(TM) in the non-coherent
case, and the non-cacheable alias for DMA buffers is private to the
kernel anyway, we can simplify things slightly and make the code more
readable by just using PAGE_KERNEL as the base pgprot.
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently create_mapping is marked with __ref, apparently because it
refers to early_alloc. However, create_mapping has no logic to prevent
erroneous use of early_alloc after it has been freed, and is only ever
called by __init functions anyway. Thus the __ref marker is misleading
and unnecessary.
Instead, this patch marks create_mapping as __init, resulting in
warnings if it is used from a a non __init functions, and allowing its
memory to be reclaimed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It is not needed after booting, this patch moves the
free_initrd_mem() function to the __init section.
This patch also make keep_initrd __initdata, to reduce kernel
size.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, the minimal default BUG() implementation from asm-
generic is used for arm64.
This patch uses the BRK software breakpoint instruction to generate
a trap instead, similarly to most other arches, with the generic
BUG code generating the dmesg boilerplate.
This allows bug metadata to be moved to a separate table and
reduces the amount of inline code at BUG and WARN sites. This also
avoids clobbering any registers before they can be dumped.
To mitigate the size of the bug table further, this patch makes
use of the existing infrastructure for encoding addresses within
the bug table as 32-bit offsets instead of absolute pointers.
(Note that this limits the kernel size to 2GB.)
Traps are registered at arch_initcall time for aarch64, but BUG
has minimal real dependencies and it is desirable to be able to
generate bug splats as early as possible. This patch redirects
all debug exceptions caused by BRK directly to bug_handler() until
the full debug exception support has been initialised.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
'Privileged Access Never' is a new arm8.1 feature which prevents
privileged code from accessing any virtual address where read or write
access is also permitted at EL0.
This patch enables the PAN feature on all CPUs, and modifies {get,put}_user
helpers temporarily to permit access.
This will catch kernel bugs where user memory is accessed directly.
'Unprivileged loads and stores' using ldtrb et al are unaffected by PAN.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
[will: use ALTERNATIVE in asm and tidy up pan_enable check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the dynamic patching for ARM64_WORKAROUND_CLEAN_CACHE over to
the newly added alternative assembler macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Remove paragraph about writing to the Free Software Foundation's
mailing address from GPL notice.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The default dma_common_get_sgtable() implementation relies on the CPU
address of the buffer being a regular lowmem address. This is not always
the case on arm64, since allocations from the various DMA pools may have
remapped vmalloc addresses, rendering the use of virt_to_page() invalid.
Fix this by providing our own implementation based on the fact that we
can safely derive a physical address from the DMA address in both cases.
CC: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: made static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Nobody seems to be producing !SMP systems anymore, so this is just
becoming a source of kernel bugs, particularly if people want to use
coherent DMA with non-shared pages.
This patch forces CONFIG_SMP=y for arm64, removing a modest amount of
code in the process.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARMv8.1 architecture extensions introduce support for hardware
updates of the access and dirty information in page table entries. With
TCR_EL1.HA enabled, when the CPU accesses an address with the PTE_AF bit
cleared in the page table, instead of raising an access flag fault the
CPU sets the actual page table entry bit. To ensure that kernel
modifications to the page tables do not inadvertently revert a change
introduced by hardware updates, the exclusive monitor (ldxr/stxr) is
adopted in the pte accessors.
When TCR_EL1.HD is enabled, a write access to a memory location with the
DBM (Dirty Bit Management) bit set in the corresponding pte
automatically clears the read-only bit (AP[2]). Such DBM bit maps onto
the Linux PTE_WRITE bit and to check whether a writable (DBM set) page
is dirty, the kernel tests the PTE_RDONLY bit. In order to allow
read-only and dirty pages, the kernel needs to preserve the software
dirty bit. The hardware dirty status is transferred to the software
dirty bit in ptep_set_wrprotect() (using load/store exclusive loop) and
pte_modify().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 68234df4ea ("arm64: kill flush_cache_all()") removed
soft_reset() from the kernel. This was the only caller of
setup_mm_for_reboot(), so remove that also.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit 9d3bfbb4df ("arm64: Combine coherent and non-coherent
swiotlb dma_ops"), __dma_common_mmap is no longer shared between two
callers, so roll it into the remaining one.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Patch 63a4aea556 ("of: clean-up unnecessary libfdt include paths")
removed all explicit libfdt include paths, since those are no longer
necessary after the latest dtc upgrade. However, this one snuck in
during the same merge window. Remove it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- suspicious RCU usage warning
- BPF (out of bounds array read and endianness conversion)
- perf (of_node usage after of_node_put, cpu_pmu->plat_device
assignment)
- huge pmd/pud check for value 0
- rate-limiting should only take unhandled signals into account
Clean-up:
- incorrect use of pgprot_t type
- unused header include
- __init annotation to arm_cpuidle_init
- pr_debug instead of pr_error for disabled GICC entries in ACPI/MADT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R+XU
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes (and cleanups) from Catalin Marinas:
"Various arm64 fixes:
- suspicious RCU usage warning
- BPF (out of bounds array read and endianness conversion)
- perf (of_node usage after of_node_put, cpu_pmu->plat_device
assignment)
- huge pmd/pud check for value 0
- rate-limiting should only take unhandled signals into account
Clean-up:
- incorrect use of pgprot_t type
- unused header include
- __init annotation to arm_cpuidle_init
- pr_debug instead of pr_error for disabled GICC entries in
ACPI/MADT"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix show_unhandled_signal_ratelimited usage
ARM64 / SMP: Switch pr_err() to pr_debug() for disabled GICC entry
arm64: cpuidle: add __init section marker to arm_cpuidle_init
arm64: Don't report clear pmds and puds as huge
arm64: perf: fix unassigned cpu_pmu->plat_device when probing PMU PPIs
arm64: perf: Don't use of_node after putting it
arm64: fix incorrect use of pgprot_t variable
arm64/hw_breakpoint.c: remove unnecessary header
arm64: bpf: fix endianness conversion bugs
arm64: bpf: fix out-of-bounds read in bpf2a64_offset()
ARM64: smp: Fix suspicious RCU usage with ipi tracepoints
Commit 86dca36e6b introduced ratelimited usage for
'unhandled_signal' messages.
The commit checks the ratelimit irrespective of whether
the signal is handled or not, which is wrong and leads
to false reports like the below in dmesg :
__do_user_fault: 127 callbacks suppressed
Do the ratelimit check only if the signal is unhandled.
Fixes: 86dca36e6b ("arm64: use private ratelimit state along with show_unhandled_signals")
Cc: Vladimir Murzin <Vladimir.Murzin@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The current pmd_huge() and pud_huge() functions simply check if the table
bit is not set and reports the entries as huge in that case. This is
counter-intuitive as a clear pmd/pud cannot also be a huge pmd/pud, and
it is inconsistent with at least arm and x86.
To prevent others from making the same mistake as me in looking at code
that calls these functions and to fix an issue with KVM on arm64 that
causes memory corruption due to incorrect page reference counting
resulting from this mistake, let's change the behavior.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Fixes: 084bd29810 ("ARM64: mm: HugeTLB support.")
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This fixes a build failure under STRICT_MM_TYPECHECKS, by adding
a missing pgprot_val() around a pgport_t reference.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently we have many duplicates in definitions of huge_pmd_unshare. In
all architectures this function just returns 0 when
CONFIG_ARCH_WANT_HUGE_PMD_SHARE is N.
This patch puts the default implementation in mm/hugetlb.c and lets these
architectures use the common code.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Rientjes <rientjes@google.com>
Cc: James Yang <James.Yang@freescale.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fixing another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YeGl
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Mostly refactoring/clean-up:
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fix another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
arm64: use private ratelimit state along with show_unhandled_signals
arm64: show unhandled SP/PC alignment faults
arm64: vdso: work-around broken ELF toolchains in Makefile
arm64: kernel: rename __cpu_suspend to keep it aligned with arm
arm64: compat: print compat_sp instead of sp
arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP
arm64: entry: fix context tracking for el0_sp_pc
arm64: defconfig: enable memtest
arm64: mm: remove reference to tlb.S from comment block
arm64: Do not attempt to use init_mm in reset_context()
arm64: KVM: Switch vgic save/restore to alternative_insn
arm64: alternative: Introduce feature for GICv3 CPU interface
arm64: psci: fix !CONFIG_HOTPLUG_CPU build warning
arm64: fix bug for reloading FPSIMD state after CPU hotplug.
arm64: kernel thread don't need to save fpsimd context.
arm64: fix missing syscall trace exit
arm64: alternative: Work around .inst assembler bugs
arm64: alternative: Merge alternative-asm.h into alternative.h
arm64: alternative: Allow immediate branch as alternative instruction
arm64: Rework alternate sequence for ARM erratum 845719
...
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
printk_ratelimit() shares the ratelimiting state with other callers what
may lead to scenarios where at the time we want to print out debug
information we already limited, so nothing appears in the dmesg - this
makes exception-trace quite poor helper in debugging.
Additionally, we have imbalance with some messages limited with global
ratelimit state and other messages limited with their private state
defined via pr_*_ratelimited().
To address this inconsistency show_unhandled_signals_ratelimited()
macro is introduced and caller sites are converted to use it.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Report unhandled SP/PC alignment faults if the show_unhandled_signals
variable is set (via /proc/sys/debug/exception-trace).
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The memmap freeing code in free_unused_memmap() computes the end of
each memblock by adding the memblock size onto the base. However,
if SPARSEMEM is enabled then the value (start) used for the base
may already have been rounded downwards to work out which memmap
entries to free after the previous memblock.
This may cause memmap entries that are in use to get freed.
In general, you're not likely to hit this problem unless there
are at least 2 memblocks and one of them is not aligned to a
sparsemem section boundary. Note that carve-outs can increase
the number of memblocks by splitting the regions listed in the
device tree.
This problem doesn't occur with SPARSEMEM_VMEMMAP, because the
vmemmap code deals with freeing the unused regions of the memmap
instead of requiring the arch code to do it.
This patch gets the memblock base out of the memblock directly when
computing the block end address to ensure the correct value is used.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
section 6.2.17 _CCA states that ARM platforms require ACPI _CCA
object to be specified for DMA-cabpable devices. Therefore, this patch
specifies ACPI_CCA_REQUIRED in arm64 Kconfig.
In addition, to handle the case when _CCA is missing, arm64 would assign
dummy_dma_ops to disable DMA capability of the device.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After secondary CPU boot or hotplug, the active_mm of the idle thread is
&init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1
and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the
TTBR0_EL1 is already set to the reserved value, there is no need to
perform any context reset.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
asm/alternative-asm.h and asm/alternative.h are extremely similar,
and really deserve to live in the same file (as this makes further
modufications a bit easier).
Fold the content of alternative-asm.h into alternative.h, and
update the few users.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, the FDT blob needs to be in the same 512 MB region as
the kernel, so that it can be mapped into the kernel virtual memory
space very early on using a minimal set of statically allocated
translation tables.
Now that we have early fixmap support, we can relax this restriction,
by moving the permanent FDT mapping to the fixmap region instead.
This way, the FDT blob may be anywhere in memory.
This also moves the vetting of the FDT to mmu.c, since the early
init code in head.S does not handle mapping of the FDT anymore.
At the same time, fix up some comments in head.S that have gone stale.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This splits off the reservation of the memory occupied by the FDT
binary itself from the processing of the memory reservations it
contains. This is necessary because the physical address of the FDT,
which is needed to perform the reservation, may not be known to the
FDT driver core, i.e., it may be mapped outside the linear direct
mapping, in which case __pa() returns a bogus value.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The documented semantics of flush_cache_all are not possible to provide
for arm64 (short of flushing the entire physical address space by VA),
and there are currently no users; KVM uses VA maintenance exclusively,
cpu_reset is never called, and the only two users outside of arch code
cannot be built for arm64.
While cpu_soft_reset and related functions (which call flush_cache_all)
were thought to be useful for kexec, their current implementations only
serve to mask bugs. For correctness kexec will need to perform
maintenance by VA anyway to account for system caches, line migration,
and other subtleties of the cache architecture. As the extent of this
cache maintenance will be kexec-specific, it should probably live in the
kexec code.
This patch removes flush_cache_all, and related unused components,
preventing further abuse.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Introduce faulthandler_disabled() and use it to check for irq context and
disabled pagefaults (via pagefault_disable()) in the pagefault handlers.
Please note that we keep the in_atomic() checks in place - to detect
whether in irq context (in which case preemption is always properly
disabled).
In contrast, preempt_disable() should never be used to disable pagefaults.
With !CONFIG_PREEMPT_COUNT, preempt_disable() doesn't modify the preempt
counter, and therefore the result of in_atomic() differs.
We validate that condition by using might_fault() checks when calling
might_sleep().
Therefore, add a comment to faulthandler_disabled(), describing why this
is needed.
faulthandler_disabled() and pagefault_disable() are defined in
linux/uaccess.h, so let's properly add that include to all relevant files.
This patch is based on a patch from Thomas Gleixner.
Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bigeasy@linutronix.de
Cc: borntraeger@de.ibm.com
Cc: daniel.vetter@intel.com
Cc: heiko.carstens@de.ibm.com
Cc: herbert@gondor.apana.org.au
Cc: hocko@suse.cz
Cc: hughd@google.com
Cc: mst@redhat.com
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: schwidefsky@de.ibm.com
Cc: yang.shi@windriver.com
Link: http://lkml.kernel.org/r/1431359540-32227-7-git-send-email-dahi@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This fix the below build error:
arch/arm64/mm/dump.c: In function ‘ptdump_init’:
arch/arm64/mm/dump.c:331:18: error: ‘VMEMMAP_START_NR’ undeclared (first use in this function)
address_markers[VMEMMAP_START_NR].start_address =
^
arch/arm64/mm/dump.c:331:18: note: each undeclared identifier is reported only once for each
function it appears in
arch/arm64/mm/dump.c:333:18: error: ‘VMEMMAP_END_NR’ undeclared (first use in this function)
address_markers[VMEMMAP_END_NR].start_address =
^
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jungseung Lee <js07.lee@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
__dma_alloc() does a PAGE_ALIGN() on the passed in size argument before
doing anything else. __dma_free() does not. And because it doesn't, it is
possible to leak memory should size not be an integer multiple of PAGE_SIZE.
The solution is to add a PAGE_ALIGN() to __dma_free() like is done in
__dma_alloc().
Additionally, this patch removes a redundant PAGE_ALIGN() from
__dma_alloc_coherent(), since __dma_alloc_coherent() can only be called
from __dma_alloc(), which already does a PAGE_ALIGN() before the call.
Cc: stable@vger.kernel.org
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Buffers allocated by dma_alloc_coherent() are always zeroed on Alpha,
ARM (32bit), MIPS, PowerPC, x86/x86_64 and probably other architectures.
It turned out that some drivers rely on this 'feature'. Allocated buffer
might be also exposed to userspace with dma_mmap() call, so clearing it
is desired from security point of view to avoid exposing random memory
to userspace. This patch unifies dma_alloc_coherent() behavior on ARM64
architecture with other implementations by unconditionally zeroing
allocated buffer.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The main change here is a significant head.S rework that allows us to
boot on machines with physical memory at a really high address without
having to increase our mapped VA range. Other changes include:
- AES performance boost for Cortex-A57
- AArch32 (compat) userspace with 64k pages
- Cortex-A53 erratum workaround for #845719
- defconfig updates (new platforms, PCI, ...)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVLnQpAAoJELescNyEwWM03RIH/iwcDc0MBZgkwfD5cnY+29p4
m89lMDo3SyGQT4NynHSw7P3R7c3zULmI+9hmJMw/yfjjjL6m7X+vVAF3xj1Am4Al
OzCqYLHyFnlRktzJ6dWeF1Ese7tWqPpxn+OCXgYNpz/r5MfF/HhlyX/qNzAQPKrw
ZpDvnt44DgUfweqjTbwQUg2wkyCRjmz57MQYxDcmJStdpHIu24jWOvDIo3OJGjyS
L49I9DU6DGUhkISZmmBE0T7vmKMD1BcgI7OIzX2WIqn521QT+GSLMhRxaHmK1s1V
A8gaMTwpo0xFhTAt7sbw/5+2663WmfRdZI+FtduvORsoxX6KdDn7DH1NQixIm8s=
=+F0I
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Here are the core arm64 updates for 4.1.
Highlights include a significant rework to head.S (allowing us to boot
on machines with physical memory at a really high address), an AES
performance boost on Cortex-A57 and the ability to run a 32-bit
userspace with 64k pages (although this requires said userspace to be
built with a recent binutils).
The head.S rework spilt over into KVM, so there are some changes under
arch/arm/ which have been acked by Marc Zyngier (KVM co-maintainer).
In particular, the linker script changes caused us some issues in
-next, so there are a few merge commits where we had to apply fixes on
top of a stable branch.
Other changes include:
- AES performance boost for Cortex-A57
- AArch32 (compat) userspace with 64k pages
- Cortex-A53 erratum workaround for #845719
- defconfig updates (new platforms, PCI, ...)"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (39 commits)
arm64: fix midr range for Cortex-A57 erratum 832075
arm64: errata: add workaround for cortex-a53 erratum #845719
arm64: Use bool function return values of true/false not 1/0
arm64: defconfig: updates for 4.1
arm64: Extract feature parsing code from cpu_errata.c
arm64: alternative: Allow immediate branch as alternative instruction
arm64: insn: Add aarch64_insn_decode_immediate
ARM: kvm: round HYP section to page size instead of log2 upper bound
ARM: kvm: assert on HYP section boundaries not actual code size
arm64: head.S: ensure idmap_t0sz is visible
arm64: pmu: add support for interrupt-affinity property
dt: pmu: extend ARM PMU binding to allow for explicit interrupt affinity
arm64: head.S: ensure visibility of page tables
arm64: KVM: use ID map with increased VA range if required
arm64: mm: increase VA range of identity map
ARM: kvm: implement replacement for ld's LOG2CEIL()
arm64: proc: remove unused cpu_get_pgd macro
arm64: enforce x1|x2|x3 == 0 upon kernel entry as per boot protocol
arm64: remove __calc_phys_offset
arm64: merge __enable_mmu and __turn_mmu_on
...
Add support for memtest command line option.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an architecture fully supports randomizing the ELF load location,
a per-arch mmap_rnd() function is used to find a randomized mmap base.
In preparation for randomizing the location of ET_DYN binaries
separately from mmap, this renames and exports these functions as
arch_mmap_rnd(). Additionally introduces CONFIG_ARCH_HAS_ELF_RANDOMIZE
for describing this feature on architectures that support it
(which is a superset of ARCH_BINFMT_ELF_RANDOMIZE_PIE, since s390
already supports a separated ET_DYN ASLR from mmap ASLR without the
ARCH_BINFMT_ELF_RANDOMIZE_PIE logic).
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for splitting out ET_DYN ASLR, this refactors the use of
mmap_rnd() to be used similarly to arm and x86. This additionally
enables mmap ASLR on legacy mmap layouts, which appeared to be missing
on arm64, and was already supported on arm. Additionally removes a
copy/pasted declaration of an unused function.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We would want to use number of page table level to define mm_struct.
Let's expose it as CONFIG_PGTABLE_LEVELS.
ARM64_PGTABLE_LEVELS is renamed to PGTABLE_LEVELS and defined before
sourcing init/Kconfig: arch/Kconfig will define default value and it's
sourced from init/Kconfig.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The page size and the number of translation levels, and hence the supported
virtual address range, are build-time configurables on arm64 whose optimal
values are use case dependent. However, in the current implementation, if
the system's RAM is located at a very high offset, the virtual address range
needs to reflect that merely because the identity mapping, which is only used
to enable or disable the MMU, requires the extended virtual range to map the
physical memory at an equal virtual offset.
This patch relaxes that requirement, by increasing the number of translation
levels for the identity mapping only, and only when actually needed, i.e.,
when system RAM's offset is found to be out of reach at runtime.
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Current implementation doesn't zero out the pages allocated.
Honor the __GFP_ZERO flag and zero out if set.
Cc: <stable@vger.kernel.org> # v3.14+
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixmap indices are in the interval (FIX_HOLE, __end_of_fixed_addresses),
but in __set_fixmap we only check idx <= __end_of_fixed_addresses, and
therefore indices <= FIX_HOLE are erroneously accepted. If called with
such an idx, __set_fixmap may corrupt page tables outside of the fixmap
region.
This patch ensures that we validate the idx against both endpoints of
the interval.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This effectively unexports set_memory_ro and set_memory_rw functions from
commit 11d91a770f ("arm64: Add CONFIG_DEBUG_SET_MODULE_RONX support").
No module user of those is in mainline kernel and we explicitly do not want
modules to use these functions, as they i.e. RO-protect eBPF (interpreted and
JIT'ed) images from malicious modifications/bugs.
Outside of eBPF scope, I believe also other set_memory_* functions should
be unexported on arm64 due to non-existant mainline module user. Laura
mentioned that they have some uses for modules doing set_memory_*, but
none that are in mainline and it's unclear if they would ever get there.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The set_memory_* functions currently only support module
addresses. The addresses are validated using is_module_addr.
That function is special though and relies on internal state
in the module subsystem to work properly. At the time of
module initialization and calling set_memory_*, it's too early
for is_module_addr to work properly so it always returns
false. Rather than be subject to the whims of the module state,
just bounds check against the module virtual address range.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With commit 3690951fc6 (arm64: Use swiotlb late initialisation), the
swiotlb buffer size is limited to MAX_ORDER_NR_PAGES. However, there are
platforms with 32-bit only devices that require bounce buffering via
swiotlb. This patch changes the swiotlb initialisation to an early 64MB
memblock allocation. In order to get the swiotlb buffer correctly
allocated (via memblock_virt_alloc_low_nopanic), this patch also defines
ARCH_LOW_ADDRESS_LIMIT to the maximum physical address capable of 32-bit
DMA.
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Merge second set of updates from Andrew Morton:
"More of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (83 commits)
mm/nommu.c: fix arithmetic overflow in __vm_enough_memory()
mm/mmap.c: fix arithmetic overflow in __vm_enough_memory()
vmstat: Reduce time interval to stat update on idle cpu
mm/page_owner.c: remove unnecessary stack_trace field
Documentation/filesystems/proc.txt: describe /proc/<pid>/map_files
mm: incorporate read-only pages into transparent huge pages
vmstat: do not use deferrable delayed work for vmstat_update
mm: more aggressive page stealing for UNMOVABLE allocations
mm: always steal split buddies in fallback allocations
mm: when stealing freepages, also take pages created by splitting buddy page
mincore: apply page table walker on do_mincore()
mm: /proc/pid/clear_refs: avoid split_huge_page()
mm: pagewalk: fix misbehavior of walk_page_range for vma(VM_PFNMAP)
mempolicy: apply page table walker on queue_pages_range()
arch/powerpc/mm/subpage-prot.c: use walk->vma and walk_page_vma()
memcg: cleanup preparation for page table walk
numa_maps: remove numa_maps->vma
numa_maps: fix typo in gather_hugetbl_stats
pagemap: use walk->vma instead of calling find_vma()
clear_refs: remove clear_refs_private->vma and introduce clear_refs_test_walk()
...
- reimplementation of the virtual remapping of UEFI Runtime Services in
a way that is stable across kexec
- emulation of the "setend" instruction for 32-bit tasks (user
endianness switching trapped in the kernel, SCTLR_EL1.E0E bit set
accordingly)
- compat_sys_call_table implemented in C (from asm) and made it a
constant array together with sys_call_table
- export CPU cache information via /sys (like other architectures)
- DMA API implementation clean-up in preparation for IOMMU support
- macros clean-up for KVM
- dropped some unnecessary cache+tlb maintenance
- CONFIG_ARM64_CPU_SUSPEND clean-up
- defconfig update (CPU_IDLE)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X5x/
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"arm64 updates for 3.20:
- reimplementation of the virtual remapping of UEFI Runtime Services
in a way that is stable across kexec
- emulation of the "setend" instruction for 32-bit tasks (user
endianness switching trapped in the kernel, SCTLR_EL1.E0E bit set
accordingly)
- compat_sys_call_table implemented in C (from asm) and made it a
constant array together with sys_call_table
- export CPU cache information via /sys (like other architectures)
- DMA API implementation clean-up in preparation for IOMMU support
- macros clean-up for KVM
- dropped some unnecessary cache+tlb maintenance
- CONFIG_ARM64_CPU_SUSPEND clean-up
- defconfig update (CPU_IDLE)
The EFI changes going via the arm64 tree have been acked by Matt
Fleming. There is also a patch adding sys_*stat64 prototypes to
include/linux/syscalls.h, acked by Andrew Morton"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (47 commits)
arm64: compat: Remove incorrect comment in compat_siginfo
arm64: Fix section mismatch on alloc_init_p[mu]d()
arm64: Avoid breakage caused by .altmacro in fpsimd save/restore macros
arm64: mm: use *_sect to check for section maps
arm64: drop unnecessary cache+tlb maintenance
arm64:mm: free the useless initial page table
arm64: Enable CPU_IDLE in defconfig
arm64: kernel: remove ARM64_CPU_SUSPEND config option
arm64: make sys_call_table const
arm64: Remove asm/syscalls.h
arm64: Implement the compat_sys_call_table in C
syscalls: Declare sys_*stat64 prototypes if __ARCH_WANT_(COMPAT_)STAT64
compat: Declare compat_sys_sigpending and compat_sys_sigprocmask prototypes
arm64: uapi: expose our struct ucontext to the uapi headers
smp, ARM64: Kill SMP single function call interrupt
arm64: Emulate SETEND for AArch32 tasks
arm64: Consolidate hotplug notifier for instruction emulation
arm64: Track system support for mixed endian EL0
arm64: implement generic IOMMU configuration
arm64: Combine coherent and non-coherent swiotlb dma_ops
...
Currently we have many duplicates in definitions around
follow_huge_addr(), follow_huge_pmd(), and follow_huge_pud(), so this
patch tries to remove the m. The basic idea is to put the default
implementation for these functions in mm/hugetlb.c as weak symbols
(regardless of CONFIG_ARCH_WANT_GENERAL_HUGETL B), and to implement
arch-specific code only when the arch needs it.
For follow_huge_addr(), only powerpc and ia64 have their own
implementation, and in all other architectures this function just returns
ERR_PTR(-EINVAL). So this patch sets returning ERR_PTR(-EINVAL) as
default.
As for follow_huge_(pmd|pud)(), if (pmd|pud)_huge() is implemented to
always return 0 in your architecture (like in ia64 or sparc,) it's never
called (the callsite is optimized away) no matter how implemented it is.
So in such architectures, we don't need arch-specific implementation.
In some architecture (like mips, s390 and tile,) their current
arch-specific follow_huge_(pmd|pud)() are effectively identical with the
common code, so this patch lets these architecture use the common code.
One exception is metag, where pmd_huge() could return non-zero but it
expects follow_huge_pmd() to always return NULL. This means that we need
arch-specific implementation which returns NULL. This behavior looks
strange to me (because non-zero pmd_huge() implies that the architecture
supports PMD-based hugepage, so follow_huge_pmd() can/should return some
relevant value,) but that's beyond this cleanup patch, so let's keep it.
Justification of non-trivial changes:
- in s390, follow_huge_pmd() checks !MACHINE_HAS_HPAGE at first, and this
patch removes the check. This is OK because we can assume MACHINE_HAS_HPAGE
is true when follow_huge_pmd() can be called (note that pmd_huge() has
the same check and always returns 0 for !MACHINE_HAS_HPAGE.)
- in s390 and mips, we use HPAGE_MASK instead of PMD_MASK as done in common
code. This patch forces these archs use PMD_MASK, but it's OK because
they are identical in both archs.
In s390, both of HPAGE_SHIFT and PMD_SHIFT are 20.
In mips, HPAGE_SHIFT is defined as (PAGE_SHIFT + PAGE_SHIFT - 3) and
PMD_SHIFT is define as (PAGE_SHIFT + PAGE_SHIFT + PTE_ORDER - 3), but
PTE_ORDER is always 0, so these are identical.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 523d6e9fae (arm64:mm: free the useless initial page table)
introduced a BUG_ON checking for the allocation type but it was
referring the early_alloc() function in the __init section. This patch
changes the check to slab_is_available() and also relaxes the BUG to a
WARN_ON_ONCE.
Reported-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The {pgd,pud,pmd}_bad family of macros have slightly fuzzy
cross-architecture semantics, and seem to imply a populated entry that
is not a next-level table, rather than a particular type of entry (e.g.
a section map).
In arm64 code, for those cases where we care about whether an entry is a
section mapping, we can instead use the {pud,pmd}_sect macros to
explicitly check for this case. This helps to document precisely what we
care about, making the code easier to read, and allows for future
relaxation of the *_bad macros to check for other "bad" entries.
To that end this patch updates the table dumping and initial table setup
to check for section mappings with {pud,pmd}_sect, and adds/restores
BUG_ON(*_bad((*p)) checks after we've handled the *_sect and *_none
cases so as to catch remaining "bad" cases.
In the fault handling code, show_pte is left with *_bad checks as it
only cares about whether it can walk the next level table, and this path
is used for both kernel and userspace fault handling. The former case
will be followed by a die() where we'll report the address that
triggered the fault, which can be useful context for debugging.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Steve Capper <steve.capper@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In paging_init, we call flush_cache_all, but this is backed by Set/Way
operations which may not achieve anything in the presence of cache line
migration and/or system caches. If the caches are already in an
inconsistent state at this point, there is nothing we can do (short of
flushing the entire physical address space by VA) to empty architected
and system caches. As such, flush_cache_all only serves to mask other
potential bugs. Hence, this patch removes the boot-time call to
flush_cache_all.
Immediately after the cache maintenance we flush the TLBs, but this is
also unnecessary. Before enabling the MMU, the TLBs are invalidated, and
thus are initially clean. When changing the contents of active tables
(e.g. in fixup_executable() for DEBUG_RODATA) we perform the required
TLB maintenance following the update, and therefore no additional
maintenance is required to ensure the new table entries are in effect.
Since activating the MMU we will not have modified system register
fields permitted to be cached in a TLB, and therefore do not need
maintenance for any cached system register fields. Hence, the TLB flush
is unnecessary.
Shortly after the unnecessary TLB flush, we update TTBR0 to point to an
empty zero page rather than the idmap, and flush the TLBs. This
maintenance is necessary to remove the global idmap entries from the
TLBs (as they would conflict with userspace mappings), and is retained.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Steve Capper <steve.capper@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For 64K page system, after mapping a PMD section, the corresponding initial
page table is not needed any more. That page can be freed.
Signed-off-by: Zhichang Yuan <zhichang.yuan@linaro.org>
[catalin.marinas@arm.com: added BUG_ON() to catch late memblock freeing]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM64_CPU_SUSPEND config option was introduced to make code providing
context save/restore selectable only on platforms requiring power
management capabilities.
Currently ARM64_CPU_SUSPEND depends on the PM_SLEEP config option which
in turn is set by the SUSPEND config option.
The introduction of CPU_IDLE for arm64 requires that code configured
by ARM64_CPU_SUSPEND (context save/restore) should be compiled in
in order to enable the CPU idle driver to rely on CPU operations
carrying out context save/restore.
The ARM64_CPUIDLE config option (ARM64 generic idle driver) is therefore
forced to select ARM64_CPU_SUSPEND, even if there may be (ie PM_SLEEP)
failed dependencies, which is not a clean way of handling the kernel
configuration option.
For these reasons, this patch removes the ARM64_CPU_SUSPEND config option
and makes the context save/restore dependent on CPU_PM, which is selected
whenever either SUSPEND or CPU_IDLE are configured, cleaning up dependencies
in the process.
This way, code previously configured through ARM64_CPU_SUSPEND is
compiled in whenever a power management subsystem requires it to be
present in the kernel (SUSPEND || CPU_IDLE), which is the behaviour
expected on ARM64 kernels.
The cpu_suspend and cpu_init_idle CPU operations are added only if
CPU_IDLE is selected, since they are CPU_IDLE specific methods and
should be grouped and defined accordingly.
PSCI CPU operations are updated to reflect the introduced changes.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since dev_archdata now has a dma_coherent state, combine the two
coherent and non-coherent operations and remove their declaration,
together with set_dma_ops, from the arch dma-mapping.h file.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We initialise the SCTLR_EL1 value by read-modify-writeback
of the desired bits, leaving the other bits (including reserved
bits(RESx)) untouched. However, sometimes the boot monitor could
leave garbage values in the RESx bits which could have different
implications. This patch makes sure that all the bits, including
the RESx bits, are set to the proper state, except for the
'endianness' control bits, EE(25) & E0E(24)- which are set early
in the el2_setup.
Updated the state of the Bit[6] in the comment to RES0 in the
comment.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The arm64 dump code is currently relying on some definitions which are
pulled in via transitive dependencies. It seems we have implicit
dependencies on the following definitions:
* MODULES_VADDR (asm/memory.h)
* MODULES_END (asm/memory.h)
* PAGE_OFFSET (asm/memory.h)
* PTE_* (asm/pgtable-hwdef.h)
* ENOMEM (linux/errno.h)
* device_initcall (linux/init.h)
This patch ensures we explicitly include the relevant headers for the
above items, fixing the observed build issue and hopefully preventing
future issues as headers are refactored.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Mark Brown <broonie@kernel.org>
Acked-by: Steve Capper <steve.capper@linaro.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
PCI IO space was intended to be 16MiB, at 32MiB below MODULES_VADDR, but
commit d1e6dc91b5 ("arm64: Add architectural support for PCI")
extended this to cover the full 32MiB. The final 8KiB of this 32MiB is
also allocated for the fixmap, allowing for potential clashes between
the two.
This change was masked by assumptions in mem_init and the page table
dumping code, which assumed the I/O space to be 16MiB long through
seaparte hard-coded definitions.
This patch changes the definition of the PCI I/O space allocation to
live in asm/memory.h, along with the other VA space allocations. As the
fixmap allocation depends on the number of fixmap entries, this is moved
below the PCI I/O space allocation. Both the fixmap and PCI I/O space
are guarded with 2MB of padding. Sites assuming the I/O space was 16MiB
are moved over use new PCI_IO_{START,END} definitions, which will keep
in sync with the size of the IO space (now restored to 16MiB).
As a useful side effect, the use of the new PCI_IO_{START,END}
definitions prevents a build issue in the dumping code due to a (now
redundant) missing include of io.h for PCI_IOBASE.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: reorder FIXADDR and PCI_IO address_markers_idx enum]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since c9465b4ec3 (arm64: add support to dump the kernel page tables)
allmodconfig has failed to build on arm64 as a result of:
../arch/arm64/mm/dump.c:55:20: error: 'PCI_IOBASE' undeclared here (not in a function)
Fix this by explicitly including io.h to ensure that a definition is
present.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the create_mapping() code in mm/mmu.c is able to support
setting up kernel page tables at initcall time, we can move the whole
virtmap creation to arm64_enable_runtime_services() instead of having
a distinct stage during early boot. This also allows us to drop the
arm64-specific EFI_VIRTMAP flag.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add page protections for arm64 similar to those in arm.
This is for security reasons to prevent certain classes
of exploits. The current method:
- Map all memory as either RWX or RW. We round to the nearest
section to avoid creating page tables before everything is mapped
- Once everything is mapped, if either end of the RWX section should
not be X, we split the PMD and remap as necessary
- When initmem is to be freed, we change the permissions back to
RW (using stop machine if necessary to flush the TLB)
- If CONFIG_DEBUG_RODATA is set, the read only sections are set
read only.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When booting with EFI, we acquire the EFI memory map after parsing the
early params. This unfortuantely renders the option useless as we call
memblock_enforce_memory_limit (which uses memblock_remove_range behind
the scenes) before we've added any memblocks. We end up removing
nothing, then adding all of memory later when efi_init calls
reserve_regions.
Instead, we can log the limit and apply this later when we do the rest
of the memblock work in memblock_init, which should work regardless of
the presence of EFI. At the same time we may as well move the early
parameter into arm64's mm/init.c, close to arm64_memblock_init.
Any memory which must be mapped (e.g. for use by EFI runtime services)
must be mapped explicitly reather than relying on the linear mapping,
which may be truncated as a result of a mem= option passed on the kernel
command line.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch partially reverts commit 421520ba98
(only the arm64 part). There is no guarantee that the boot-loader places other
images like dtb in a different page than initrd start/end, especially when the
kernel is built with 64KB pages. When this happens, such pages must not be
freed. The free_reserved_area() already takes care of rounding up "start" and
rounding down "end" to avoid freeing partially used pages.
Cc: <stable@vger.kernel.org> # 3.17+
Reported-by: Peter Maydell <Peter.Maydell@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we have common ESR_ELx_* macros, move the core arm64 code over
to them.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
The cachepolicy kernel parameter was intended to aid in the debugging of
coherency issues, but it is fundamentally broken for several reasons:
* On SMP platforms, only the boot CPU's tcr_el1 is altered. Secondary
CPUs may therefore use differ w.r.t. the attributes they apply to
MT_NORMAL memory, resulting in a loss of coherency.
* The cache maintenance using flush_dcache_all (based on Set/Way
operations) is not guaranteed to empty a given CPU's cache hierarchy
while said CPU has caches enabled, it cannot empty the caches of
other coherent PEs, nor is it guaranteed to flush data to the PoC
even when caches are disabled.
* The TLBs are not invalidated around the modification of MAIR_EL1 and
TCR_EL1, as required by the architecture (as both are permitted to be
cached in a TLB). This may result in CPUs using attributes other than
those expected for some memory accesses, resulting in a loss of
coherency.
* Exclusive accesses are not architecturally guaranteed to function as
expected on memory marked as Write-Through or Non-Cacheable. Thus
changing the attributes of MT_NORMAL away from the (architecurally
safe) defaults may cause uses of these instructions (e.g. atomics) to
behave erratically.
Given this, the cachepolicy code cannot be used for debugging purposes
as it alone is likely to cause coherency issues. This patch removes the
broken cachepolicy code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we have moved the call to SetVirtualAddressMap() to the stub,
UEFI has no use for the ID map, so we can drop the code that installs
ID mappings for UEFI memory regions.
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
For UEFI, we need to install the memory mappings used for Runtime Services
in a dedicated set of page tables. Add create_pgd_mapping(), which allows
us to allocate and install those page table entries early.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Currently, swapper_pg_dir and idmap_pg_dir share the init_mm mm_struct
instance. To allow the introduction of other pg_dir instances, for instance,
for UEFI's mapping of Runtime Services, make the struct_mm instance an
explicit argument that gets passed down to the pmd and pte instantiation
functions. Note that the consumers (pmd_populate/pgd_populate) of the
mm_struct argument don't actually inspect it, but let's fix it for
correctness' sake.
Acked-by: Steve Capper <steve.capper@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
If the final page table entry we walk is a valid mapping, the page table
dumping code will not log the region this entry is part of, as the final
note_page call in ptdump_show will trigger an early return. Luckily this
isn't seen on contemporary systems as they typically don't have enough
RAM to extend the linear mapping right to the end of the address space.
In note_page, we log a region when we reach its end (i.e. we hit an
entry immediately afterwards which has different prot bits or is
invalid). The final entry has no subsequent entry, so we will not log
this immediately. We try to cater for this with a subsequent call to
note_page in ptdump_show, but this returns early as 0 < LOWEST_ADDR, and
hence we will skip a valid mapping if it spans to the final entry we
note.
Unlike 32-bit ARM, the pgd with the kernel mapping is never shared with
user mappings, so we do not need the check to ensure we don't log user
page tables. Due to the way addr is constructed in the walk_* functions,
it can never be less than LOWEST_ADDR when walking the page tables, so
it is not necessary to avoid dereferencing invalid table addresses. The
existing checks for st->current_prot and st->marker[1].start_address are
sufficient to ensure we will not print and/or dereference garbage when
trying to log information.
This patch removes the unnecessary check against LOWEST_ADDR, ensuring
we log all regions in the kernel page table, including those which span
right to the end of the address space.
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When building with 48-bit VAs, it's possible to get the following
warning when building the arm64 page table dumping code:
arch/arm64/mm/dump.c: In function ‘walk_pgd’:
arch/arm64/mm/dump.c:266:2: warning: right shift count >= width of type
pgd_t *pgd = pgd_offset(mm, 0);
^
As pgd_offset is a macro and the second argument is not cast to any
particular type, the zero will be given integer type by the compiler.
As pgd_offset passes the pargument to pgd_index, we then try to shift
the 32-bit integer by at least 39 bits (for 4k pages).
Elsewhere the pgd_offset is passed a second argument of unsigned long
type, so let's do the same here by passing '0UL' rather than '0'.
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The commit 3690951fc6
(arm64: Use swiotlb late initialisation)
switches the DMA mapping code to swiotlb_tlb_late_init_with_default_size(),
the arm64_swiotlb_init() will not used anymore, so remove this function.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Update handling of cacheflush syscall with changes made in arch/arm
counterpart:
- return error to userspace when flushing syscall fails
- split user cache-flushing into interruptible chunks
- don't bother rounding to nearest vma
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
[will: changed internal return value from -EINTR to 0 to match arch/arm/]
Signed-off-by: Will Deacon <will.deacon@arm.com>
In a similar manner to arm, it's useful to be able to dump the page
tables to verify permissions and memory types. Add a debugfs file
to check the page tables.
Acked-by: Steve Capper <steve.capper@linaro.org>
Tested-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
[will: s/BUFFERABLE/NORMAL-NC/]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The fixmap API was originally added for arm64 for
early_ioremap purposes. It can be used for other purposes too
so move the initialization from ioremap to somewhere more
generic. This makes it obvious where the fixmap is being set
up and allows for a cleaner implementation of __set_fixmap.
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARM errata 819472, 826319, 827319 and 824069 define the same
workaround for these hardware issues in certain Cortex-A53 parts.
Use the new alternatives framework and the CPU MIDR detection to
patch "cache clean" into "cache clean and invalidate" instructions if
an affected CPU is detected at runtime.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[will: add __maybe_unused to squash gcc warning]
Signed-off-by: Will Deacon <will.deacon@arm.com>
With a blatant copy of some x86 bits we introduce the alternative
runtime patching "framework" to arm64.
This is quite basic for now and we only provide the functions we need
at this time.
This is connected to the newly introduced feature bits.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Translation faults that occur due to the input address being outside
of the address range mapped by the relevant base register are reported
as level 0 faults in ESR.DFSC.
If the faulting access cannot be resolved by the kernel (e.g. because
it is not mapped by a vma), then we report "input address range fault"
on the console. This was fine until we added support for 48-bit VAs,
which actually place PGDs at level 0 and can trigger faults for invalid
addresses that are within the range of the page tables.
This patch changes the string to report "level 0 translation fault",
which is far less confusing.
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently allocate different levels of page tables with a variety of
differing flags, and the PGALLOC_GFP flags, intended for use when
allocating any level of page table, are only used for ptes in
pte_alloc_one. On x86, PGALLOC_GFP is used for all page table
allocations.
Currently the major differences are:
* __GFP_NOTRACK -- Needed to ensure page tables are always accessible in
the presence of kmemcheck to prevent recursive faults. Currently
kmemcheck cannot be selected for arm64.
* __GFP_REPEAT -- Causes the allocator to try to reclaim pages and retry
upon a failure to allocate.
* __GFP_ZERO -- Sometimes passed explicitly, sometimes zalloc variants
are used.
While we've no encountered issues so far, it would be preferable to be
consistent. This patch ensures all levels of table are allocated in the
same manner, with PGALLOC_GFP.
Cc: Steve Capper <steve.capper@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit 8a0a9bd4db ('random: make get_random_int() more
random'), get_random_int() returns a random value for each call,
so comment and hack introduced in mmap_rnd() as part of commit
1d18c47c73 ('arm64: MMU fault handling and page table management')
are incorrects.
Commit 1d18c47c73 seems to use the same hack introduced by
commit a5adc91a4b ('powerpc: Ensure random space between stack
and mmaps'), latter copied in commit 5a0efea09f ('sparc64: Sharpen
address space randomization calculations.').
But both architectures were cleaned up as part of commit
fa8cbaaf5a ('powerpc+sparc64/mm: Remove hack in mmap randomize
layout') as hack is no more needed since commit 8a0a9bd4db.
So the present patch removes the comment and the hack around
get_random_int() on AArch64's mmap_rnd().
Cc: David S. Miller <davem@davemloft.net>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use phys_addr_t for physical address in alloc_init_pud. Although
phys_addr_t and unsigned long are 64 bit in arm64, it is better
to use phys_addr_t to describe physical addresses.
Signed-off-by: Min-Hua Chen <orca.chen@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With 48-bit VA space, the 64K page configuration uses 3 levels instead
of 2 and PUD_SIZE != PMD_SIZE. Since with 64K pages we only cover
PMD_SIZE with the initial swapper_pg_dir populated in head.S, the
memblock current_limit needs to be set accordingly in map_mem() to avoid
allocating unmapped memory. The memblock current_limit is progressively
increased as more blocks are mapped.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Compiling with STRICT_MM_TYPECHECKS gives the following
arch/arm64/mm/ioremap.c: In function ‘early_ioremap_init’:
arch/arm64/mm/ioremap.c:152:2: warning: passing argument 3 of
‘pud_populate’ from incompatible pointer type
pud_populate(&init_mm, pud, bm_pmd);
The data types for bm_pmd and bm_pud are incorrectly set to pte_t.
This patch corrects these types.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When the pgd size is smaller than PAGE_SIZE, pgd_alloc() uses kzalloc()
to save space. However, this is not always naturally aligned as required
by the architecture. This patch creates a kmem_cache for pgd allocations
with the correct alignment.
The current kernel configurations with 4K pages + 39-bit VA and 64K
pages + 42-bit VA use a full page for the pgd and are not affected. The
patch is required for 48-bit VA with 64K pages where the pgd is 512
bytes.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Activate the RCU fast_gup for ARM64. We also need to force THP splits to
broadcast an IPI s.t. we block in the fast_gup page walker. As THP
splits are comparatively rare, this should not lead to a noticeable
performance degradation.
Some pre-requisite functions pud_write and pud_page are also added.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neither CMA nor noncoherent allocations support atomic allocations.
Add a dedicated atomic pool to support this.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Riley <davidriley@chromium.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ritesh Harjain <ritesh.harjani@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- eBPF JIT compiler for arm64
- CPU suspend backend for PSCI (firmware interface) with standard idle
states defined in DT (generic idle driver to be merged via a different
tree)
- Support for CONFIG_DEBUG_SET_MODULE_RONX
- Support for unmapped cpu-release-addr (outside kernel linear mapping)
- set_arch_dma_coherent_ops() implemented and bus notifiers removed
- EFI_STUB improvements when base of DRAM is occupied
- Typos in KGDB macros
- Clean-up to (partially) allow kernel building with LLVM
- Other clean-ups (extern keyword, phys_addr_t usage)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SAfQ
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- eBPF JIT compiler for arm64
- CPU suspend backend for PSCI (firmware interface) with standard idle
states defined in DT (generic idle driver to be merged via a
different tree)
- Support for CONFIG_DEBUG_SET_MODULE_RONX
- Support for unmapped cpu-release-addr (outside kernel linear mapping)
- set_arch_dma_coherent_ops() implemented and bus notifiers removed
- EFI_STUB improvements when base of DRAM is occupied
- Typos in KGDB macros
- Clean-up to (partially) allow kernel building with LLVM
- Other clean-ups (extern keyword, phys_addr_t usage)
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (51 commits)
arm64: Remove unneeded extern keyword
ARM64: make of_device_ids const
arm64: Use phys_addr_t type for physical address
aarch64: filter $x from kallsyms
arm64: Use DMA_ERROR_CODE to denote failed allocation
arm64: Fix typos in KGDB macros
arm64: insn: Add return statements after BUG_ON()
arm64: debug: don't re-enable debug exceptions on return from el1_dbg
Revert "arm64: dmi: Add SMBIOS/DMI support"
arm64: Implement set_arch_dma_coherent_ops() to replace bus notifiers
of: amba: use of_dma_configure for AMBA devices
arm64: dmi: Add SMBIOS/DMI support
arm64: Correct ftrace calls to aarch64_insn_gen_branch_imm()
arm64:mm: initialize max_mapnr using function set_max_mapnr
setup: Move unmask of async interrupts after possible earlycon setup
arm64: LLVMLinux: Fix inline arm64 assembly for use with clang
arm64: pageattr: Correctly adjust unaligned start addresses
net: bpf: arm64: fix module memory leak when JIT image build fails
arm64: add PSCI CPU_SUSPEND based cpu_suspend support
arm64: kernel: introduce cpu_init_idle CPU operation
...
This patch extends the start and end address of initrd to be page aligned,
so that we can free all memory including the un-page aligned head or tail
page of initrd, if the start or end address of initrd are not page
aligned, the page can't be freed by free_initrd_mem() function.
Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the type of physical address from unsigned long to phys_addr_t,
make valid_phys_addr_range more readable.
Signed-off-by: Min-Hua Chen <orca.chen@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch replaces the static assignment of ~0 to dma_handle with
DMA_ERROR_CODE to be consistent with other platforms.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 6ecba8eb51 (arm64: Use bus notifiers to set per-device coherent
DMA ops) introduced bus notifiers to set the coherent dma ops based on
the 'dma-coherent' DT property. Since the generic of_dma_configure()
handles this property for platform and AMBA devices, replace the
notifiers with set_arch_dma_coherent_ops().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Initializing max_mapnr using set_max_mapnr() helper function instead
of direct reference. Also not adding PHYS_PFN_OFFSET to max_pfn,
since it already contains it.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@caviumnetworks.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Remove '#' from immediate parameter in AARCH64 inline assembly in mmu.
This code now works with both gcc and clang.
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The start address needs to be actually updated after it
is detected to be unaligned. Adjust it and the end address
properly.
Reported-by: Zi Shen Lim <zlim.lnx@gmail.com>
Reviewed-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 86c8b27a01cf:
"arm64: ignore DT memreserve entries when booting in UEFI mode
prevents early_init_fdt_scan_reserved_mem() from being called for
arm64 kernels booting via UEFI. This was done because the kernel
will use the UEFI memory map to determine reserved memory regions.
That approach has problems in that early_init_fdt_scan_reserved_mem()
also reserves the FDT itself and any node-specific reserved memory.
By chance of some kernel configs, the FDT may be overwritten before
it can be unflattened and the kernel will fail to boot. More subtle
problems will result if the FDT has node specific reserved memory
which is not really reserved.
This patch has the UEFI stub remove the memory reserve map entries
from the FDT as it does with the memory nodes. This allows
early_init_fdt_scan_reserved_mem() to be called unconditionally
so that the other needed reservations are made.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
In a similar fashion to other architecture, add the infrastructure
and Kconfig to enable DEBUG_SET_MODULE_RONX support. When
enabled, module ranges will be marked read-only/no-execute as
appropriate.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
[will: fixed off-by-one in module end check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The current soft_restart() and setup_restart implementations incorrectly
assume that compiler will not spill/fill values to/from stack. However
this assumption seems to be wrong, revealed by the disassembly of the
currently existing code (v3.16) built with Linaro GCC 4.9-2014.05.
ffffffc000085224 <soft_restart>:
ffffffc000085224: a9be7bfd stp x29, x30, [sp,#-32]!
ffffffc000085228: 910003fd mov x29, sp
ffffffc00008522c: f9000fa0 str x0, [x29,#24]
ffffffc000085230: 94003d21 bl ffffffc0000946b4 <setup_mm_for_reboot>
ffffffc000085234: 94003b33 bl ffffffc000093f00 <flush_cache_all>
ffffffc000085238: 94003dfa bl ffffffc000094a20 <cpu_cache_off>
ffffffc00008523c: 94003b31 bl ffffffc000093f00 <flush_cache_all>
ffffffc000085240: b0003321 adrp x1, ffffffc0006ea000 <reset_devices>
ffffffc000085244: f9400fa0 ldr x0, [x29,#24] ----> spilled addr
ffffffc000085248: f942fc22 ldr x2, [x1,#1528] ----> global memstart_addr
ffffffc00008524c: f0000061 adrp x1, ffffffc000094000 <__inval_cache_range+0x40>
ffffffc000085250: 91290021 add x1, x1, #0xa40
ffffffc000085254: 8b010041 add x1, x2, x1
ffffffc000085258: d2c00802 mov x2, #0x4000000000 // #274877906944
ffffffc00008525c: 8b020021 add x1, x1, x2
ffffffc000085260: d63f0020 blr x1
...
Here the compiler generates memory accesses after the cache is disabled,
loading stale values for the spilled value and global variable. As we cannot
control when the compiler will access memory we must rewrite the
functions in assembly to stash values we need in registers prior to
disabling the cache, avoiding the use of memory.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
UEFI provides its own method for marking regions to reserve, via the
memory map which is also used to initialise memblock. So when using the
UEFI memory map, ignore any memreserve entries present in the DT.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Changes include:
- Context tracking support (NO_HZ_FULL) which narrowly missed 3.16
- vDSO layout rework following Andy's work on x86
- TEXT_OFFSET fuzzing for bootloader testing
- /proc/cpuinfo tidy-up
- Preliminary work to support 48-bit virtual addresses, but this is
currently disabled until KVM has been ported to use it (the patches
do, however, bring some nice clean-up)
- Boot-time CPU sanity checks (especially useful on heterogenous
systems)
- Support for syscall auditing
- Support for CC_STACKPROTECTOR
- defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6XMc
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Once again, Catalin's off on holiday and I'm looking after the arm64
tree. Please can you pull the following arm64 updates for 3.17?
Note that this branch also includes the new GICv3 driver (merged via a
stable tag from Jason's irqchip tree), since there is a fix for older
binutils on top.
Changes include:
- context tracking support (NO_HZ_FULL) which narrowly missed 3.16
- vDSO layout rework following Andy's work on x86
- TEXT_OFFSET fuzzing for bootloader testing
- /proc/cpuinfo tidy-up
- preliminary work to support 48-bit virtual addresses, but this is
currently disabled until KVM has been ported to use it (the patches
do, however, bring some nice clean-up)
- boot-time CPU sanity checks (especially useful on heterogenous
systems)
- support for syscall auditing
- support for CC_STACKPROTECTOR
- defconfig updates"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (55 commits)
arm64: add newline to I-cache policy string
Revert "arm64: dmi: Add SMBIOS/DMI support"
arm64: fpsimd: fix a typo in fpsimd_save_partial_state ENDPROC
arm64: don't call break hooks for BRK exceptions from EL0
arm64: defconfig: enable devtmpfs mount option
arm64: vdso: fix build error when switching from LE to BE
arm64: defconfig: add virtio support for running as a kvm guest
arm64: gicv3: Allow GICv3 compilation with older binutils
arm64: fix soft lockup due to large tlb flush range
arm64/crypto: fix makefile rule for aes-glue-%.o
arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL
arm64: Fix barriers used for page table modifications
arm64: Add support for 48-bit VA space with 64KB page configuration
arm64: asm/pgtable.h pmd/pud definitions clean-up
arm64: Determine the vmalloc/vmemmap space at build time based on VA_BITS
arm64: Clean up the initial page table creation in head.S
arm64: Remove asm/pgtable-*level-types.h files
arm64: Remove asm/pgtable-*level-hwdef.h files
arm64: Convert bool ARM64_x_LEVELS to int ARM64_PGTABLE_LEVELS
arm64: mm: Implement 4 levels of translation tables
...
Rather than guessing what the maximum vmmemap space should be, this
patch allows the calculation based on the VA_BITS and sizeof(struct
page). The vmalloc space extends to the beginning of the vmemmap space.
Since the virtual kernel memory layout now depends on the build
configuration, this patch removes the detailed description in
Documentation/arm64/memory.txt in favour of information printed during
kernel booting.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Jungseok Lee <jungseoklee85@gmail.com>
Rather than having several Kconfig options, define int
ARM64_PGTABLE_LEVELS which will be also useful in converting some of the
pgtable macros.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Jungseok Lee <jungseoklee85@gmail.com>
This patch implements 4 levels of translation tables since 3 levels
of page tables with 4KB pages cannot support 40-bit physical address
space described in [1] due to the following issue.
It is a restriction that kernel logical memory map with 4KB + 3 levels
(0xffffffc000000000-0xffffffffffffffff) cannot cover RAM region from
544GB to 1024GB in [1]. Specifically, ARM64 kernel fails to create
mapping for this region in map_mem function since __phys_to_virt for
this region reaches to address overflow.
If SoC design follows the document, [1], over 32GB RAM would be placed
from 544GB. Even 64GB system is supposed to use the region from 544GB
to 576GB for only 32GB RAM. Naturally, it would reach to enable 4 levels
of page tables to avoid hacking __virt_to_phys and __phys_to_virt.
However, it is recommended 4 levels of page table should be only enabled
if memory map is too sparse or there is about 512GB RAM.
References
----------
[1]: Principles of ARM Memory Maps, White Paper, Issue C
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Reviewed-by: Sungjinn Chung <sungjinn.chung@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Steve Capper <steve.capper@linaro.org>
[catalin.marinas@arm.com: MEMBLOCK_INITIAL_LIMIT removed, same as PUD_SIZE]
[catalin.marinas@arm.com: early_ioremap_init() updated for 4 levels]
[catalin.marinas@arm.com: 48-bit VA depends on BROKEN until KVM is fixed]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Jungseok Lee <jungseoklee85@gmail.com>
The early_ioremap_init() function already handles fixmap pte
initialisation, so upgrade this to cover all of pud/pmd/pte and remove
one page from swapper_pg_dir.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Jungseok Lee <jungseoklee85@gmail.com>
ZONE_DMA is created to allow 32-bit only devices to access memory in the
absence of an IOMMU. On systems where the memory starts above 4GB, it is
expected that some devices have a DMA offset hardwired to be able to
access the bottom of the memory. Linux currently supports DT bindings
for the DMA offsets but they are not (easily) available early during
boot.
This patch tries to guess a DMA offset and assumes that ZONE_DMA
corresponds to the 32-bit mask above the start of DRAM.
Fixes: 2d5a5612bc (arm64: Limit the CMA buffer to 32-bit if ZONE_DMA)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Tested-by: Anup Patel <anup.patel@linaro.org>
Currently we place swapper_pg_dir and idmap_pg_dir below the kernel
image, between PHYS_OFFSET and (PHYS_OFFSET + TEXT_OFFSET). However,
bootloaders may use portions of this memory below the kernel and we do
not parse the memory reservation list until after the MMU has been
enabled. As such we may clobber some memory a bootloader wishes to have
preserved.
To enable the use of all of this memory by bootloaders (when the
required memory reservations are communicated to the kernel) it is
necessary to move our initial page tables elsewhere. As we currently
have an effectively unbound requirement for memory at the end of the
kernel image for .bss, we can place the page tables here.
This patch moves the initial page table to the end of the kernel image,
after the BSS. As they do not consist of any initialised data they will
be stripped from the kernel Image as with the BSS. The BSS clearing
routine is updated to stop at __bss_stop rather than _end so as to not
clobber the page tables, and memory reservations made redundant by the
new organisation are removed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The __cpu_clear_user_page() and __cpu_copy_user_page() functions
are not currently exported. This prevents modules from using
clear_user_page() and copy_user_page().
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The __sync_icache_dcache routine will only flush the dcache for the
first page of a compound page, potentially leading to stale icache
data residing further on in a hugetlb page.
This patch addresses this issue by taking into consideration the
order of the page when flushing the dcache.
Reported-by: Mark Brown <broonie@linaro.org>
Tested-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> # v3.11+
When the CMA buffer is allocated, it is too early to know whether
devices will require ZONE_DMA memory. This patch limits the CMA buffer
to (DMA_BIT_MASK(32) + 1) if CONFIG_ZONE_DMA is enabled.
In addition, it computes the dma_to_phys(DMA_BIT_MASK(32)) before the
increment (no current functional change).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Strings library contributed to glibc but re-licensed under GPLv2)
- Optimised crypto algorithms making use of the ARMv8 crypto extensions
(together with kernel API for using FPSIMD instructions in interrupt
context)
- Ftrace support
- CPU topology parsing from DT
- ESR_EL1 (Exception Syndrome Register) exposed to user space signal
handlers for SIGSEGV/SIGBUS (useful to emulation tools like Qemu)
- 1GB section linear mapping if applicable
- Barriers usage clean-up
- Default pgprot clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=Jj8U
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux into next
Pull arm64 updates from Catalin Marinas:
- Optimised assembly string/memory routines (based on the AArch64
Cortex Strings library contributed to glibc but re-licensed under
GPLv2)
- Optimised crypto algorithms making use of the ARMv8 crypto extensions
(together with kernel API for using FPSIMD instructions in interrupt
context)
- Ftrace support
- CPU topology parsing from DT
- ESR_EL1 (Exception Syndrome Register) exposed to user space signal
handlers for SIGSEGV/SIGBUS (useful to emulation tools like Qemu)
- 1GB section linear mapping if applicable
- Barriers usage clean-up
- Default pgprot clean-up
Conflicts as per Catalin.
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (57 commits)
arm64: kernel: initialize broadcast hrtimer based clock event device
arm64: ftrace: Add system call tracepoint
arm64: ftrace: Add CALLER_ADDRx macros
arm64: ftrace: Add dynamic ftrace support
arm64: Add ftrace support
ftrace: Add arm64 support to recordmcount
arm64: Add 'notrace' attribute to unwind_frame() for ftrace
arm64: add __ASSEMBLY__ in asm/insn.h
arm64: Fix linker script entry point
arm64: lib: Implement optimized string length routines
arm64: lib: Implement optimized string compare routines
arm64: lib: Implement optimized memcmp routine
arm64: lib: Implement optimized memset routine
arm64: lib: Implement optimized memmove routine
arm64: lib: Implement optimized memcpy routine
arm64: defconfig: enable a few more common/useful options in defconfig
ftrace: Make CALLER_ADDRx macros more generic
arm64: Fix deadlock scenario with smp_send_stop()
arm64: Fix machine_shutdown() definition
arm64: Support arch_irq_work_raise() via self IPIs
...
Pull ARM64 EFI update from Peter Anvin:
"By agreement with the ARM64 EFI maintainers, we have agreed to make
-tip the upstream for all EFI patches. That is why this patchset
comes from me :)
This patchset enables EFI stub support for ARM64, like we already have
on x86"
* 'arm64-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64: efi: only attempt efi map setup if booting via EFI
efi/arm64: ignore dtb= when UEFI SecureBoot is enabled
doc: arm64: add description of EFI stub support
arm64: efi: add EFI stub
doc: arm: add UEFI support documentation
arm64: add EFI runtime services
efi: Add shared FDT related functions for ARM/ARM64
arm64: Add function to create identity mappings
efi: add helper function to get UEFI params from FDT
doc: efi-stub.txt updates for ARM
lib: add fdt_empty_tree.c
Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs. So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.
Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most architectures
except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The introduction
of generic serial earlycon support went in thru tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTjzgyAAoJEMhvYp4jgsXiFsUH/1PMTGo8CyD62VQD5ZKdAoW+
Fq6vCiRQ8assF5i5ZLcW1DqhjtoRaCKYhVbRKa5lj7cZdjlSpacI/qQPrF5Br2Ii
bTE3Ff/AQwipQaz/Bj7HqJCgGwfWK8xdfgW0abKsyXMWDN86Bov/zzeu8apmws0x
H1XjJRgnc/rzM4m9ny6+lss0iq6YL54SuTYNzHR33+Ywxls69SfHXIhCW0KpZcBl
5U3YUOomt40GfO46sxFA4xApAhypEK4oVq7asyiA2ArTZ/c2Pkc9p5CBqzhDLmlq
yioWTwHIISv0q+yMLCuQrVGIsbUDkQyy7RQ15z6U+/e/iGO/M+j3A5yxMc3qOi4=
=Onff
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next
Pull DeviceTree updates from Rob Herring:
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most
architectures except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The
introduction of generic serial earlycon support went in through the
tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
* tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (58 commits)
of: handle NULL node in next_child iterators
of/irq: provide more wrappers for !CONFIG_OF
devicetree: bindings: Document micrel vendor prefix
dt: bindings: dwc2: fix required value for the phy-names property
of_pci_irq: kill useless variable in of_irq_parse_pci()
of/irq: do irq resolution in platform_get_irq_byname()
of: Add a testcase for of_find_node_by_path()
of: Make of_find_node_by_path() handle /aliases
of: Create unlocked version of for_each_child_of_node()
lib: add glibc style strchrnul() variant
of: Handle memory@0 node on PPC32 only
pci/of: Remove dead code
of: fix race between search and remove in of_update_property()
of: Use NULL for pointers
of: Stop naming platform_device using dcr address
of: Ensure unique names without sacrificing determinism
tty/serial: pl011: add DT based earlycon support
of/fdt: add FDT serial scanning for earlycon
of/fdt: add FDT address translation support
serial: earlycon: add DT support
...
The following happens when trying to run a kvm guest on a kernel
configured for 64k pages. This doesn't happen with 4k pages:
BUG: failure at include/linux/mm.h:297/put_page_testzero()!
Kernel panic - not syncing: BUG!
CPU: 2 PID: 4228 Comm: qemu-system-aar Tainted: GF 3.13.0-0.rc7.31.sa2.k32v1.aarch64.debug #1
Call trace:
[<fffffe0000096034>] dump_backtrace+0x0/0x16c
[<fffffe00000961b4>] show_stack+0x14/0x1c
[<fffffe000066e648>] dump_stack+0x84/0xb0
[<fffffe0000668678>] panic+0xf4/0x220
[<fffffe000018ec78>] free_reserved_area+0x0/0x110
[<fffffe000018edd8>] free_pages+0x50/0x88
[<fffffe00000a759c>] kvm_free_stage2_pgd+0x30/0x40
[<fffffe00000a5354>] kvm_arch_destroy_vm+0x18/0x44
[<fffffe00000a1854>] kvm_put_kvm+0xf0/0x184
[<fffffe00000a1938>] kvm_vm_release+0x10/0x1c
[<fffffe00001edc1c>] __fput+0xb0/0x288
[<fffffe00001ede4c>] ____fput+0xc/0x14
[<fffffe00000d5a2c>] task_work_run+0xa8/0x11c
[<fffffe0000095c14>] do_notify_resume+0x54/0x58
In arch/arm/kvm/mmu.c:unmap_range(), we end up doing an extra put_page()
on the stage2 pgd which leads to the BUG in put_page_testzero(). This
happens because a pud_huge() test in unmap_range() returns true when it
should always be false with 2-level pages tables used by 64k pages.
This patch removes support for huge puds if 2-level pagetables are
being used.
Signed-off-by: Mark Salter <msalter@redhat.com>
[catalin.marinas@arm.com: removed #ifndef around PUD_SIZE check]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> # v3.11+
This reverts commit bc07c2c6e9.
While the aim is increased security for --x memory maps, it does not
protect against kernel level reads. Until SECCOMP is implemented for
arm64, revert this patch to avoid giving a false idea of execute-only
mappings.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to ensure ordering and completion of inner-shareable maintenance
instructions (cache and TLB) on AArch64, we can use the -ish suffix to
the dmb and dsb instructions respectively.
This patch updates our low-level cache and tlb maintenance routines to
use the inner-shareable barrier variants where appropriate.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The tlb maintainence functions: __cpu_flush_user_tlb_range and
__cpu_flush_kern_tlb_range do not take into consideration the page
granule when looping through the address range, and repeatedly flush
tlb entries for the same page when operating with 64K pages.
This patch re-works the logic s.t. we instead advance the loop by
1 << (PAGE_SHIFT - 12), so avoid repeating ourselves.
Also the routines have been converted from assembler to static inline
functions to aid with legibility and potential compiler optimisations.
The isb() has been removed from flush_tlb_kernel_range(.) as it is
only needed when changing the execute permission of a mapping. If one
needs to set an area of the kernel as execute/non-execute an isb()
must be inserted after the call to flush_tlb_kernel_range.
Cc: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We have the capability to map 1GB level 1 blocks when using a 4K
granule.
This patch adjusts the create_mapping logic s.t. when mapping physical
memory on boot, we attempt to use a 1GB block if both the VA and PA
start and end are 1GB aligned. This both reduces the levels of lookup
required to resolve a kernel logical address, as well as reduces TLB
pressure on cores that support 1GB TLB entries.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Tested-by: Jungseok Lee <jays.lee@samsung.com>
[catalin.marinas@arm.com: s/prot_sect_kernel/PROT_SECT_NORMAL_EXEC/]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The primary aim of this patchset is to remove the pgprot_default and
prot_sect_default global variables and rely strictly on predefined
values. The original goal was to be able to run SMP kernels on UP
hardware by not setting the Shareability bit. However, it is unlikely to
see UP ARMv8 hardware and even if we do, the Shareability bit is no
longer assumed to disable cacheable accesses.
A side effect is that the device mappings now have the Shareability
attribute set. The hardware, however, should ignore it since Device
accesses are always Outer Shareable.
Following the removal of the two global variables, there is some PROT_*
macro reshuffling and cleanup, including the __PAGE_* macros (replaced
by PAGE_*).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The ARMv8 architecture allows execute-only user permissions by clearing
the PTE_UXN and PTE_USER bits. The kernel, however, can still access
such page, so execute-only page permission does not protect against
read(2)/write(2) etc. accesses. Systems requiring such protection must
implement/enable features like SECCOMP.
This patch changes the arm64 __P100 and __S100 protection_map[] macros
to the new __PAGE_EXECONLY attributes. A side effect is that
pte_valid_user() no longer triggers for __PAGE_EXECONLY since PTE_USER
isn't set. To work around this, the check is done on the PTE_NG bit via
the pte_valid_ng() macro. VM_READ is also checked now for page faults.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For AArch32, bit 11 (WnR) of the FSR/ESR register is set when the fault
was caused by a write access and applications like Qemu rely on such
information being provided in sigcontext. This patch introduces the
ESR_EL1 tracking for the arm64 kernel faults and sets bit 11 accordingly
in compat sigcontext.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Recently, the default DMA ops have been changed to non-coherent for
alignment with 32-bit ARM platforms (and DT files). This patch adds bus
notifiers to be able to set the coherent DMA ops (with no cache
maintenance) for devices explicitly marked as coherent via the
"dma-coherent" DT property.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently arm64 dma_ops is by default made coherent which makes it
opposite in default policy from arm.
Make default dma_ops to be noncoherent (same as arm), as currently there
aren't any dma-capable drivers which assumes coherent ops
Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix for the arm64 kern_addr_valid() function to recognize
virtual addresses in the kernel logical memory map. The
function fails as written because it does not check whether
the addresses in that region are mapped at the pmd level to
2MB or 512MB pages, continues the page table walk to the
pte level, and issues a garbage value to pfn_valid().
Tested on 4K-page and 64K-page kernels.
Signed-off-by: Dave Anderson <anderson@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
At boot time, before switching to a virtual UEFI memory map, firmware
expects UEFI memory and IO regions to be identity mapped whenever
kernel makes runtime services calls. The existing early boot code
creates an identity map of kernel text/data but this is not sufficient
for UEFI. This patch adds a create_id_mapping() function which reuses
the core code of the existing create_mapping().
Signed-off-by: Mark Salter <msalter@redhat.com>
[ Fixed error message formatting (%pa). ]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Move the /memreserve/ processing and dtb memory reservations into
early_init_fdt_scan_reserved_mem. This converts arm, arm64, and powerpc
as they are the only users of early_init_fdt_scan_reserved_mem.
memblock_reserve is safe to call on the same region twice, so the
reservation check for the dtb in powerpc 32-bit reservations is safe to
remove.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
- Additional cache flushing during boot (needed in the presence of
external caches or under virtualisation)
- DMA range invalidation fix for non cache line aligned buffers
- Build failure fix with !COMPAT
- Kconfig update for STRICT_DEVMEM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=mDkd
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull second set of arm64 updates from Catalin Marinas:
"A second pull request for this merging window, mainly with fixes and
docs clarification:
- Documentation clarification on CPU topology and booting
requirements
- Additional cache flushing during boot (needed in the presence of
external caches or under virtualisation)
- DMA range invalidation fix for non cache line aligned buffers
- Build failure fix with !COMPAT
- Kconfig update for STRICT_DEVMEM"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix DMA range invalidation for cache line unaligned buffers
arm64: Add missing Kconfig for CONFIG_STRICT_DEVMEM
arm64: fix !CONFIG_COMPAT build failures
Revert "arm64: virt: ensure visibility of __boot_cpu_mode"
arm64: Relax the kernel cache requirements for boot
arm64: Update the TCR_EL1 translation granule definitions for 16K pages
ARM: topology: Make it clear that all CPUs need to be described
If the buffer needing cache invalidation for inbound DMA does start or
end on a cache line aligned address, we need to use the non-destructive
clean&invalidate operation. This issue was introduced by commit
7363590d2c (arm64: Implement coherent DMA API based on swiotlb).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jon Medhurst (Tixy) <tixy@linaro.org>
Add support for early IO or memory mappings which are needed before the
normal ioremap() is usable. This also adds fixmap support for permanent
fixed mappings such as that used by the earlyprintk device register
region.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently, paging_init() calls init_mem_pgprot() to initialize pgprot
values used by macros such as PAGE_KERNEL, PAGE_KERNEL_EXEC, etc.
The new fixmap and early_ioremap support also needs to use these macros
before paging_init() is called. This patch moves the init_mem_pgprot()
call out of paging_init() and into setup_arch() so that pgprot_default
gets initialized in time for fixmap and early_ioremap.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With system caches for the host OS or architected caches for guest OS we
cannot easily guarantee that there are no dirty or stale cache lines for
the areas of memory written by the kernel during boot with the MMU off
(therefore non-cacheable accesses).
This patch adds the necessary cache maintenance during boot and relaxes
the booting requirements.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The current TCR register setting in arch/arm64/mm/proc.S assumes that
TCR_EL1.TG* fields are one bit wide and bit 31 is RES1 (reserved, set to
1). With the addition of 16K pages (currently unsupported in the
kernel), the TCR_EL1.TG* fields have been extended to two bits. This
patch updates the corresponding Linux definitions and drops the bit 31
setting in proc.S in favour of the new macros.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Joe Sylve <joe.sylve@gmail.com>
Updates to devicetree core code. This branch contains the following notable changes:
* Add reserved memory binding
* Make struct device_node a kobject and remove legacy /proc/device-tree
* ePAPR conformance fixes
* Update in-kernel DTC copy to version v1.4.0
* Preparation changes for dynamic device tree overlays
* minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of the
old /proc/device-tree code. This simplifies the device tree handling
code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=lyA5
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree changes from Grant Likely:
"Updates to devicetree core code. This branch contains the following
notable changes:
- add reserved memory binding
- make struct device_node a kobject and remove legacy
/proc/device-tree
- ePAPR conformance fixes
- update in-kernel DTC copy to version v1.4.0
- preparatory changes for dynamic device tree overlays
- minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of
the old /proc/device-tree code. This simplifies the device tree
handling code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (29 commits)
dt: Remove dangling "select PROC_DEVICETREE"
of: Add support for ePAPR "stdout-path" property
of: device_node kobject lifecycle fixes
of: only scan for reserved mem when fdt present
powerpc: add support for reserved memory defined by device tree
arm64: add support for reserved memory defined by device tree
of: add missing major vendors
of: add vendor prefix for SMSC
of: remove /proc/device-tree
of/selftest: Add self tests for manipulation of properties
of: Make device nodes kobjects so they show up in sysfs
arm: add support for reserved memory defined by device tree
drivers: of: add support for custom reserved memory drivers
drivers: of: add initialization code for dynamic reserved memory
drivers: of: add initialization code for static reserved memory
of: document bindings for reserved-memory nodes
Revert "of: fix of_update_property()"
kbuild: dtbs_install: new make target
ARM: mvebu: Allows to get the SoC ID even without PCI enabled
of: Allows to use the PCI translator without the PCI core
...
Since this macro is identical to pgprot_writecombine() and is only used
in a single place, remove it completely to avoid confusion. On ARMv7+
processors, the coherent DMA mapping must be Normal NonCacheable (a.k.a.
writecombine) to avoid mismatched hardware attribute aliases (with the
kernel linear mapping as Normal Cacheable).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
DMA_ATTR_WRITE_COMBINE is currently ignored. Set the pgprot
appropriately for non coherent opperations.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The current dma_ops do not specify an mmap function so maping
falls back to the default implementation. There are at least
two issues with using the default implementation:
1) The pgprot is always pgprot_noncached (strongly ordered)
memory even with coherent operations
2) dma_common_mmap calls virt_to_page on the remapped non-coherent
address which leads to invalid memory being mapped.
Fix both these issue by implementing a custom mmap function which
correctly accounts for remapped addresses and sets vm_pg_prot
appropriately.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
[catalin.marinas@arm.com: replaced "arm64_" with "__" prefix for consistency]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARMv8 supports a range of physical address bit sizes. The PARange bits
from ID_AA64MMFR0_EL1 register are read during boot-time and the
intermediate physical address size bits are written in the translation
control registers (TCR_EL1 and VTCR_EL2).
There is no change in the VA bits and levels of translation.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Reviewed-by: Will Deacon <Will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently we flush the entire dcache at boot within __cpu_setup, but
this is unnecessary as the booting protocol demands that the dcache is
invalid and off upon entering the kernel. The presence of the cache
flush only serves to hide bugs in bootloaders, and is not safe in the
presence of SMP.
In an SMP boot scenario the CPUs enter coherency outside of the kernel,
and the primary CPU enables its caches before bringing up secondary
CPUs. Therefore if any secondary CPU has an entry in its cache (in
violation of the boot protocol), the primary CPU might snoop it even if
the secondary CPU's cache is disabled. The boot-time cache flush only
serves to hide a firmware bug, and slows down a cpu boot unnecessarily.
This patch removes the unnecessary boot-time cache flush.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: make __flush_dcache_all local only]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds support for DMA API cache maintenance on SoCs without
hardware device cache coherency.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since arm64 does not support ISA, there is no need for early swiotlb
initialisation. This patch switches the DMA mapping code to
swiotlb_tlb_late_init_with_default_size(). A side effect of this is that
GFP_DMA is used for the swiotlb buffer and devices with a 32-bit
coherent mask are correctly supported.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On arm64 we do not have two DMA zones, so it does not make sense to
implement ZONE_DMA32. This patch changes ZONE_DMA32 with ZONE_DMA, the
latter covering 32-bit dma address space to honour GFP_DMA allocations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
arm64_swiotlb_alloc/free_coherent name can be misleading
somtimes with CMA support being enabled after this
patch (c2104debc235b745265b64d610237a6833fd53)
Change this name to be more generic:
__dma_alloc/free_coherent
Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
[catalin.marinas@arm.com: renamed arm64_swiotlb_dma_ops to coherent_swiotlb_dma_ops]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently pgd_alloc has a redundant NULL check in its return path that
can be removed with no ill effects. With that removed it's also possible
to return early and eliminate the new_pgd temporary variable.
This patch applies said modifications, making the logic of pgd_alloc
correspond 1-1 with that of pgd_free.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the 64K page size configuration, __create_page_tables in head.S
maps enough memory to get started but using 64K pages rather than 512M
sections with a single pgd/pud/pmd entry pointing to a pte table.
create_mapping() may override the pgd/pud/pmd table entry with a block
(section) one if the RAM size is more than 512MB and aligned correctly.
For the end of this block to be accessible, the old TLB entry must be
invalidated.
Cc: <stable@vger.kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
dma_alloc_from_contiguous takes number of pages for a size.
Align up the dma size passed in to page size to avoid truncation
and allocation failures on sizes less than PAGE_SIZE.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
David Woods