Johannes Berg <johannes@sipsolutions.net> says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used by drivers that cannot reliably map tx status
information onto specific skbs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This op works like .tx_status, except it does not need access to the
skb. This will be used by drivers that cannot match tx status
information to specific packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a crash on attempting to calculate the frame duration for a VHT
packet (which needs to be handled by hw/driver instead).
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of keeping track of all those special cases where
VLAN interfaces have no bss_conf.chandef, just make sure
they have the same as the AP interface they belong to.
Among others, this fixes a crash getting a VLAN's channel
from userspace since a NULL channel is returned as a good
result (return value 0) for VLANs since the commit below.
Cc: stable@vger.kernel.org [3.18 only]
Fixes: c12bc4885f ("mac80211: return the vif's chandef in ieee80211_cfg_get_channel()")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are no channels allowing 80 MHz to be used, then the
station isn't really VHT capable even if the driver and device
support it in general. In this case, exclude the VHT capability
IE from probe request frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The supported bandwidth field is a two-bit field, not a bitmap,
so treat it accordingly when disabling 80+80 or 160 MHz.
Note that we can only advertise "80+80 and 160" or "160", not
"80+80" by itself, so disabling 160 also disables 80+80.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people
-----BEGIN PGP SIGNATURE-----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=q4e6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the queue mapping earlier, skb->queue_mapping is more likely than
skb->data to still be in d-cache.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate mask code currently assumes that a rate is legacy if
IEEE80211_TX_RC_MCS is not set. This might be the cause of bogus VHT
rates being reported with minstrel_ht.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When 20MHz chandef is used, 40MHz rates shouldn't be
used (by the rate-control algorithm), even if the sta
ht capabilities indicate support for it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Singed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to use the scan and scheduled scan request pointers during
RX to check for randomisation, make them accessible using RCU.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
local->scan_req was tested in the previous line, so it
can't be NULL.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In TDLS (e.g., TDLS off-channel) there is a requirement for
some drivers to supply an unused TID between the AP and the
device to the FW, to allow sending PTI requests and to allow
the FW to aggregate on a specific TID for better throughput.
To ensure that the allocated TID is indeed unused, this patch
introduces an API for blocking the driver from TXing on that
TID.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the HW supports IEEE80211_HW_QUEUE_CONTROL, allow
flushing only specific queues rather than all of them.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving a TDLS channel switch request or response, parse the frame
and call a new tdls_recv_channel_switch op in the low level driver with
the parsed data.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the cfg80211 TDLS channel switch ops and introduce new mac80211
ones for low-level drivers.
Verify low-level driver support for the new ops when using the relevant
wiphy feature bit. Also verify the peer supports channel switching before
passing the command down.
Add a new STA flag to track the off-channel state with the TDLS peer and
make sure to cancel the channel-switch if the peer STA is unexpectedly
removed.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These are used in TDLS channel switching code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the data-generating from the Tx-sending functionality, as we do
not want to send templates to the lower driver. Also add an optional
chandef argument to the data-generating portion. It will be used for
channel-switch templates.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The AP or peer can prohibit TDLS channel switch via a bit in the
extended capabilities IE. Parse the IE and track this bit. Set an
appropriate STA flag if both the AP and peer STA support TDLS
channel-switching.
Add the new STA flag and the missing TDLS_INITIATOR to debugfs.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define some related TDLS protocol constants and advertise channel switch
support in the extended-capabilities IE when the feature bit is defined.
Actually supporting TDLS channel-switching also requires support for
some new nl80211 commands, to be introduced by future patches.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the BSS coex IE in case we support HT40 channels, as mandated by
section 8.5.13 in IEEE802.11 2012.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This information element is mandatory in case TDLS channel-switching is to
be supported. The channels given are ones supported and allowed to be
active in the current regulatory setting.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For some TDLS channel switch implementations data frames need to be
sent by the firmware based on a template. This template should be
created by mac80211, and thus needs to properly be built from an
802.3 frame into an 802.11 frame. In addition, the device will need
the key information so the select_key handler needs to be run.
However, the driver/device will be responsible for all of the crypto
encapsulation, as the sequence numbers etc. cannot be built by the
host anyway in this case since it's a template to be used multiple
times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Factor out the 802.11 header building code from the xmit function
to be able to use it separately in a later commit.
While at it, fix up some documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing the band as a parameter to ieee80211_xmit()
and ieee80211_tx(), move it outside of the two functions while
making sure info->band is set up before calling them.
This removes the parameter and simplifies the follow commit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the TDLS peer station might not receive the teardown
packet (e.g., when in PS), this makes sure the packet is
retransmitted - this time through the AP - if the TDLS peer
didn't ACK the packet.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allows setting of an skb's flags - if needed - when calling
ieee80211_subif_start_xmit().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit 5935839ad7
"mac80211: improve minstrel_ht rate sorting by throughput & probability"
introduced a crash on rate sorting that occurs when the rate added to
the sorting array is faster than all the previous rates. Due to an
off-by-one error, it reads the rate index from tp_list[-1], which
contains uninitialized stack garbage, and then uses the resulting index
for accessing the group rate stats, leading to a crash if the garbage
value is big enough.
Cc: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put duplicate detection into its own RX handler, and separate
out the conditions a bit to make the code more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Radiotap vendor namespace data might still be useful, but we
reverted it because it used too much space in the RX status.
Put it back, but address the space problem by using a single
bit only and putting everything else into the skb->data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-vif channel switches, we want to send
NL80211_CMD_CH_SWITCH_NOTIFY to the userspace to let it decide whether
other interfaces need to be moved as well. This is needed when we
want a P2P GO interface to follow the channel of a station, for
example.
Modify the code so that all interfaces can send CSA notifications.
Additionally, send notifications for STA CSA as well.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send a channel switch notification to userspace when a channel switch
is requested or when we react to a remote CSA.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The device_timestamp value was left out of the event trace for
drv_pre_channel_switch by mistake. Add it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a mistake when merging commit 6d027bcc (mac80211: add
pre_channel_switch driver operation) for upstream. The assignment of
the values in the ch_switch structure came below the call to
drv_pre_channel_switch. Fix the order.
Fixes: 6d027bcc (mac80211: add pre_channel_switch driver operation)
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7ec7c4a9a6 (mac80211: port CCMP to
cryptoapi's CCM driver) introduced a regression when decrypting empty
packets (data_len == 0). This will lead to backtraces like:
(scatterwalk_start) from [<c01312f4>] (scatterwalk_map_and_copy+0x2c/0xa8)
(scatterwalk_map_and_copy) from [<c013a5a0>] (crypto_ccm_decrypt+0x7c/0x25c)
(crypto_ccm_decrypt) from [<c032886c>] (ieee80211_aes_ccm_decrypt+0x160/0x170)
(ieee80211_aes_ccm_decrypt) from [<c031c628>] (ieee80211_crypto_ccmp_decrypt+0x1ac/0x238)
(ieee80211_crypto_ccmp_decrypt) from [<c032ef28>] (ieee80211_rx_handlers+0x870/0x1d24)
(ieee80211_rx_handlers) from [<c0330c7c>] (ieee80211_prepare_and_rx_handle+0x8a0/0x91c)
(ieee80211_prepare_and_rx_handle) from [<c0331260>] (ieee80211_rx+0x568/0x730)
(ieee80211_rx) from [<c01d3054>] (__carl9170_rx+0x94c/0xa20)
(__carl9170_rx) from [<c01d3324>] (carl9170_rx_stream+0x1fc/0x320)
(carl9170_rx_stream) from [<c01cbccc>] (carl9170_usb_tasklet+0x80/0xc8)
(carl9170_usb_tasklet) from [<c00199dc>] (tasklet_hi_action+0x88/0xcc)
(tasklet_hi_action) from [<c00193c8>] (__do_softirq+0xcc/0x200)
(__do_softirq) from [<c0019734>] (irq_exit+0x80/0xe0)
(irq_exit) from [<c0009c10>] (handle_IRQ+0x64/0x80)
(handle_IRQ) from [<c000c3a0>] (__irq_svc+0x40/0x4c)
(__irq_svc) from [<c0009d44>] (arch_cpu_idle+0x2c/0x34)
Such packets can appear for example when using the carl9170 wireless driver
because hardware sometimes generates garbage when the internal FIFO overruns.
This patch adds an additional length check.
Cc: stable@vger.kernel.org
Fixes: 7ec7c4a9a6 ("mac80211: port CCMP to cryptoapi's CCM driver")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Deliver up to 128 frames during service period instead of 8 if
unlimited is specified by the client during association.
8 was just an arbitrary value; so is 128 since unlimited can
be any number.
However for large traffic bursts, increasing this value looks
reasonable. Also, it seems that a few certification tests
expect more frames to be delivered during SP.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the RIC data element (RDE) is included in the IEs coming
from userspace for an association request, its handling is
currently broken as any IEs that are contained within it would
be split off from it and inserted again after all the IEs that
mac80211 generates (e.g. HT, VHT.)
To fix this, treat the RIC element specially, and stop after
it only when we find something that doesn't actually belong to
it. This assumes userspace is actually correctly building it,
directly after the fast BSS transition IE and before all the
others like extended capabilities.
This leaves as a potential problem the case where userspace is
building the following IEs:
[RDE] [vendor resource description] [vendor non-resource IE]
In this case, we'd erroneously consider all three IEs to be
part of the RIC data together, and not split them between the
two vendor IEs. Unfortunately, it isn't easily possible to
distinguish vendor IEs, so this isn't easy to fix. Luckily,
this case is rare as normally wpa_supplicant will include an
extended capabilities IE in the IEs, and that certainly will
break the two vendor IEs apart correctly.
Reviewed-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds 802.11p OCB (Outside the Context of a BSS) mode
support.
When communicating in OCB mode a mandatory wildcard BSSID
(48 '1' bits) is used.
The EDCA parameters handling function was changed to support
802.11p specific values.
The insertion of a newly discovered STAs is done in the similar way
as in the IBSS mode -- through the deferred insertion.
The OCB mode uses a periodic 'housekeeping task' for expiration of
disconnected STAs (in the similar manner as in the MESH mode).
New Kconfig option for verbose OCB debugging outputs is added.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The configured tx power is often limited by hardware capabilities,
channel settings, antenna configuration, etc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix tracing compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon receiving the last fragment, all but the first fragment
are freed, but the multicast check for statistics at the end
of the function refers to the current skb (the last fragment)
causing a use-after-free bug.
Since multicast frames cannot be fragmented and we check for
this early in the function, just modify that check to also
do the accounting to fix the issue.
Cc: stable@vger.kernel.org
Reported-by: Yosef Khyal <yosefx.khyal@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use codespell to find spelling errors.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface is deleted, an ongoing hardware scan is canceled and
the driver must abort the scan, at the very least reporting completion
while the interface is removed.
However, if it scheduled the work that might only run after everything
is said and done, which leads to cfg80211 warning that the scan isn't
reported as finished yet; this is no fault of the driver, it already
did, but mac80211 hasn't processed it.
To fix this situation, flush the delayed work when the interface being
removed is the one that was executing the scan.
Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the time it takes to process the beacon that started the CSA
process, we may be late for the switch if we try to reach exactly
beacon 0. To avoid that, use count - 1 when calculating the switch time.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we are switching from an HT40+ to an HT40- channel (or vice-versa),
we need the secondary channel offset IE to specify what is the
post-CSA offset to be used. This applies both to beacons and to probe
responses.
In ieee80211_parse_ch_switch_ie() we were ignoring this IE from
beacons and using the *current* HT information IE instead. This was
causing us to use the same offset as before the switch.
Fix that by using the secondary channel offset IE also for beacons and
don't ever use the pre-switch offset. Additionally, remove the
"beacon" argument from ieee80211_parse_ch_switch_ie(), since it's not
needed anymore.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace can add keys to an AP mode interface before start_ap has been
called. If there have been no calls to start_ap/stop_ap in the mean
time, the keys will still be around when the interface is brought down.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[adjust comments, fix AP_VLAN case]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When CONFIG_MAC80211_RC_MINSTREL_VHT is set, the module param
minstrel_vht_only tells minstrel_ht whether to allow the mix of ht rates
with vht rates.
ATM, minstrel_ht skips ht rates when minstrel_vht_only is true, but it does
that even if vht is not supported, which makes the sta rates fallback to
legacy as no ht rate gets enabled.
Fixes: 9208247d74 ("mac80211: minstrel_ht: add basic support for VHT rates <= 3SS@80MHz")
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All the callers of ieee80211_mgd_probe_ap_send return right
after they call the flush() callback. This means that calling
flush() is uneeded since its meaning is to wait until the
queues of the device are empty.
Devices that know how to report status on Tx will do so using
the regular path (ieee80211_tx_status) and this status will
trigger the continuation of the flow of the probe
(ieee80211_sta_tx_notify).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when creating virtual interfaces.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be helpful when using the mac80211_hwsim
wiphys and automated testing. Let user create the
vifs as needed, and named as expected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support creating wiphy devices with an optional name.
This will be used by hwsim to have better automated control
over virtual radio creation/deletion.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to iterate all stations currently uploaded to them.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During reconfig the station list is traversed in order and station are
added back to the driver. Make sure the stations are added to the driver
in the same order they were added to mac80211.
This has a real side effect - some drivers (iwlwifi) require TDLS
stations to be added only after the AP station for the same network.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers need to know which station is the TDLS link initiator.
Expose this value via the mac80211 ieee80211_sta structure.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an IV is generated, only the MAC header is moved back. The network
header location remains the same relative to the skb head, as the new IV
is using headroom space that was reserved in advance.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Export ieee80211_ie_split function, so it can be reused by
drivers which need to insert additional elements.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When displaying a rate through debugfs minstrel_ht guesses its flags
comparing group indexes. Since 3ec373c421 ("mac80211: minstrel_ht:
include type (cck/ht) in rates flag"), the rate flags of interest are
present in the mcs_group-s, so use it.
While improving the code, this also fixes a smatch false positive
"error: testing array offset 'i' after use" in minstrel_ht_stats_dump.
This warning only triggers after 9208247d74 ("mac80211: minstrel_ht:
add basic support for VHT rates <= 3SS@80MHz") with
CONFIG_MAC80211_RC_MINSTREL_VHT unset because then MINSTREL_VHT_GROUP_0
is above MINSTREL_GROUPS_NB and smatch only barks when the "testing
array offset" seems to prevent possible out of bonds accesses (which
does not happen here since i < ARRAY_SIZE(mi->groups)).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a key is tainted during resume, it is no longer programmed
into the device; however, it's uploaded flag may (will) be set.
Clear the flag when not programming it because it's tainted to
avoid attempting to remove it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the currently existing APIs between mac80211 and the low
level driver to implement WMM admission control.
The low level driver needs to report the media time used by
each transmitted packet in ieee80211_tx_status. Based on that
information, mac80211 will modify the QoS parameters of the
admission controlled Access Category when the limit is
reached. Once the original QoS parameters can be restored,
mac80211 will do so.
One issue with this approach is that management frames will
also erroneously be downgraded, but the upside is that the
implementation is simple. In the future, it can be extended
to driver- or device-based implementations that are better.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to ever set invalid CW_min/CW_max to the
drivers, we should catch it in higher layers. However, the
consequences of setting it wrong can be quite severe, so
double-check at a low level and error out for invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The debugfs_remove() function can safely take NULL parameters
so the additionally null test isn't required, and there's no
other reason to have it here, so remove it.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
[rewrite commit message, re-introduce blank line after assert]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the new CONFIG_MAC80211_RC_MINSTREL_VHT is not set (default 'N'),
there is no behavioral change including in sampling and MCS_GROUP_RATES
remains 8.
Otherwise MCS_GROUP_RATES is 10, and a module parameter *vht_only*
(default 'true'), restricts the rates selection to VHT when VHT is
supported.
Regarding the debugfs stats buffer:
It is explicitly increased from 8k to 32k to fit every rates incl. when
both HT and VHT rates are enabled, as for the format, before:
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0( 0)
after:
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0( 0)
VHT40/LGI MCS5/2 0.0 0.0 0.0 0 0( 0) 0( 0)
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM, we grep cck rates idx with idx / MCS_GROUP_RATES ==
MINSTREL_CCK_GROUP.
Matching neither-cck-non-ht rates could be done by replacing '==' with
'>', however it would be less versatile or explicit.
This will allow to match VHT rates with IEEE80211_TX_RC_VHT_MCS.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No functional change.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by
throughput & probability"), the rate indexes are manipulated via u8's
and hence allow for a maximum of 256 mcs_group entries in
minstrel_mcs_groups.
ATM, minstrel_ht advertizes support up to 3HTSS@40MHz, consuming:
8(MCS_GROUP_RATES) * (3(SS)*2(GI)*2(BW)+1(CCK)), i.e. 104 entries.
Support for 3VHTSS@80MHz will require:
10(MCS_GROUP_RATES) * (3(SS)*2(GI)*2(BW)+1(CCK)) +
10(MCS_GROUP_RATES) * (3(SS)*2(GI)*3(BW)), i.e. 130 + 180 entries.
This change moves from u8s to u16s where necessary.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This showed up as a sparse warning (with higher verbosity) and is
certainly correct - the change flags should be unsigned. It's not
that important since high flag numbers aren't used and bitwise
operations would still work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM an HT rc_stats line is 106 chars.
Times 8(MCS_GROUP_RATES)*3(SS)*2(GI)*2(BW) + CCK(4), i.e. x100, this is
well above the current 8192 - sizeof(*ms) currently allocated.
Fix this by squeezing the output as follows (not that we're short on
memory but this also improves readability and range, the new format adds
one more digit to *ok/*cum and ok/cum):
- Before (HT) (106 ch):
type rate throughput ewma prob this prob retry this succ/attempt success attempts
CCK/LP 5.5M 0.0 0.0 0.0 0 0( 0) 0 0
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0 0
- After (75 ch):
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
CCK/LP 5.5M 0.0 0.0 0.0 0 0( 0) 0( 0)
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0( 0)
- Align non-HT format Before (non-HT) (83 ch):
rate throughput ewma prob this prob this succ/attempt success attempts
ABCDP 6 0.0 0.0 0.0 0( 0) 0 0
54 0.0 0.0 0.0 0( 0) 0 0
- After (61 ch):
rate tpt eprob *prob *ok(*cum) ok( cum)
ABCDP 1 0.0 0.0 0.0 0( 0) 0( 0)
54 0.0 0.0 0.0 0( 0) 0( 0)
*This also adds dynamic checks for overflow, lowers the size of the
non-HT request (allowing > 30 entries) and replaces the buddy-rounded
allocations (s/sizeof(*ms) + 8192/8192).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to add new parameters for the del_station calls
without having to modify all drivers that use this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It affects non-(V)HT rates and can lead to selecting an rts_cts rate
that is not a basic rate or way superior to the reference rate (ATM
rates[0] used for the 1st attempt of the protected frame data).
E.g, assuming drivers register growing (bitrate) sorted tables of
ieee80211_rate-s, having :
- rates[0].idx == d'2 and basic_rates == b'10100
will select rts_cts idx b'10011 & ~d'(BIT(2)-1), i.e. 1, likewise
- rates[0].idx == d'2 and basic_rates == b'10001
will select rts_cts idx b'10000
The first is not a basic rate and the second is > rates[0].
Also, wrt severity of the addressed misbehavior, ATM we only have one
rts_cts_rate_idx rather than one per rate table entry, so this idx might
still point to bitrates > rates[1..MAX_RATES].
Fixes: 5253ffb8c9 ("mac80211: always pick a basic rate to tx RTS/CTS for pre-HT rates")
Cc: stable@vger.kernel.org
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is okay to enable DFS for channel contexts
based drivers as long as no combination advertises
radar detection and multi-channel operation at the
same time.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to store ieee80211_vif_use_reserved_context()
result and test it before returning.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch with multiple channel contexts should now work fine.
Remove check that disallows switches when multiple contexts are in
use.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of immediately reopening the queues (in case of block_tx),
calling the post_channel_switch operation and sending the
notification, wait for the first beacon on the new channel. This
makes sure that we don't lose packets if the AP/GO is not on the new
channel yet.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a counterpart to the pre_channel_switch operation, add a
post_channel_switch operation. This allows the drivers to go back to
a normal configuration after the channel switch is completed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may need to prepare for a channel switch also when it is
initiated from the remote side (eg. station, P2P client). To make
this possible, add a generic callback that can be called for all
interface types.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Extended Channel Switching capability bit in the extended
capabilities element must be set if the driver supports CSA on
non-beaconing interfaces.
Since this capability needs to be set during driver registration, the
extended_capabiliities global variable needs to be moved to the local
structure so that it can be modified.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may need the device timestamp in order to synchronize the
channel switch. To pass this value back to the driver, add it to the
channel switch structure and copy the device_timestamp value received
in the rx info structure into it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement get_mpp and dump_mpp cfg80211_ops to export the content of the
802.11s mesh proxy path table to userspace.
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The chandef of the channel context a vif is using may be different
than the chandef of the vif itself. For instance, the bandwidth used
by the vif may be narrower than the one configured in the channel
context. To avoid confusion, return the vif's chandef in
ieee80211_cfg_get_channel() instead of the chandef of the channel
context.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by
throughput & probability") replaced the constant 8 with MCS_GROUP_RATES
when getting the number of streams of an HT MCS. See commit 7a5e3fa2c8
("mac80211: minstrel_ht: replace some occurences of MCS_GROUP_RATES").
Fixes: 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by throughput & probability")
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Forgot to add an entry to the struct description of sta_info.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-09-22
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
For the bluetooth bits, Johan says:
"Here are some more patches intended for 3.18. Most of them are cleanups
or fixes for SMP. The only exception is a fix for BR/EDR L2CAP fixed
channels which should now work better together with the L2CAP
information request procedure."
For the iwlwifi bits, Emmanuel says:
"I fix here dvm which was broken by my last pull request. Arik
continues to work on TDLS and Luca solved a few issues in CT-Kill. Eyal
keeps digging into rate scaling code, more to come soon. Besides this,
nothing really special here."
Beyond that, there are the usual big batches of updates to ath9k, b43,
mwifiex, and wil6210 as well as a handful of other bits here and there.
Also, rtlwifi gets some btcoexist attention from Larry.
Please let me know if there are problems!
====================
Had to adjust the wil6210 code to comply with Joe Perches's recent
change in net-next to make the netdev_*() routines return void instead
of 'int'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed.
-----BEGIN PGP SIGNATURE-----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=OPIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a possible issue with the use, or lack thereof of sk_refcnt and
sk_wmem_alloc in the wifi ack status functionality.
Specifically if a socket were to request acknowledgements, and the socket
were to have sk_refcnt drop to 0 resulting in it waiting on sk_wmem_alloc
to reach 0 it would be possible to have sock_queue_err_skb orphan the last
buffer, resulting in __sk_free being called on the socket. After this the
buffer is enqueued on sk_error_queue, however the queue has already been
flushed resulting in at least a memory leak, if not a data corruption.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new static_smps / dynamic_smps feature bits
instead of mac80211-internal hw flags.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Take the requested smps mode from the ap params
(instead of always starting with SMPS_OFF)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correctly mark the network header location in mac80211-generated TDLS
frames. These may be used by lower-level drivers.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace might need to know what queues are configured
for uapsd (e.g. for setting proper default values in tspecs).
Add this bitmap to the association event (inside wmm
nested attribute)
Add additional parameter to cfg80211_rx_assoc_resp,
and update its callers.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding a timeout for tearing down a TDLS connection that
hasn't had ACKed traffic sent through it for a certain
amount of time.
Since we have no other monitoring facility to indicate the
existance (or non-existance) of a peer, this patch will
cause a peer to be considered as unavailable if for some X
time at least some Y packets have all not been ACKed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch improves the way minstrel_ht sorts rates according to throughput
and success probability. 3 FOR-loops across the entire rate and mcs group set
in function minstrel_ht_update_stats() which where used to determine the
fastest, second fastest and most robust rate are reduced to 2 FOR-loop.
The sorted list of rates according throughput is extended to the best four
rates as we need them in upcoming joint rate and power control. The sorting
is done via the new function minstrel_ht_sort_best_tp_rates(). The annotation
of those 4 best throughput rates in the debugfs file rc-stats is changes to:
"A,B,C,D", where A is the fastest rate and C the 4th fastest.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Tested-by: Stefan Venz <ikstream86@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minstrel and Mintrel_HT used there own structs to keep track of rate
statistics. Unify those variables in struct minstrel_rate_states and
move it to rc80211_minstrel.h for common usage. This is a clean-up
patch to prepare Minstrel and Minstrel_HT codebase for upcoming TPC.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When freeing the key, clear the memory to avoid having the
key material stick around in memory "forever".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at.
-----BEGIN PGP SIGNATURE-----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=gW3Y
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-09-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Two more fixes for mac80211 - one of them addresses a long-standing
issue that we only found when using vendor events more frequently;
the other addresses some bad information being reported in userspace
that people were starting to actually look at."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This message occasionally triggers for some people as in
https://bugzilla.redhat.com/show_bug.cgi?id=1111740 but
it's not clear which (headroom or tailroom) is at fault.
Annotate the message a bit to get more information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linux already supports 802.11h, where the access point can tell the
client to reduce its transmission power. However, 802.11h is only
defined for 5 GHz, where the need for this is much smaller than on
2.4 GHz.
Cisco has their own solution, called DTPC (Dynamic Transmit Power
Control). Cisco APs on a controller sometimes but not always send
802.11h; they always send DTPC, even on 2.4 GHz. This patch adds support
for parsing and honoring the DTPC IE in addition to the 802.11h
element (they do not always contain the same limits, so both must
be honored); the format is not documented, but very simple.
Tested (on top of wireless.git and on 3.16.1) against a Cisco Aironet
1142 joined to a Cisco 2504 WLC, by setting various transmit power
levels for the given access points and observing the results.
The Wireshark 802.11 dissector agrees with the interpretation of the
element, except for negative numbers, which seem to never happen
anyway.
Signed-off-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Decouple the logic of parsing the 802.11d and 802.11h IEs from the
part of deciding what to do about the data (messaging, clamping to
0 dBm, doing the actual setting). This paves the way for the next
patch, which introduces more data sources for transmit power limitation.
Signed-off-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit "mac80211: disable 40MHz support in case of 20MHz AP"
broke working VHT in 20Mhz with APs like Netgear R6300v2 which
do not publish support for 40Mhz but allow use of VHT in 20Mhz.
The break is because VHT is disabled once no HT cap doesn't indicate
support for 40Mhz. This causes the assoc request to be sent without
any VHT IE and the association is only HT due to this.
For more details check out commit 4a817aa7
"mac80211: allow VHT with peers not capable of 40MHz"
Fixes: 53b954ee4a ("mac80211: disable 40MHz support in case of 20MHz AP")
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend mac80211 set_coverage_class API in order to enable ACK timeout
estimation algorithm (dynack) passing coverage class equals to -1
to lower drivers. Synchronize set_coverage_class routine signature with
mac80211 function pointer for p54, ath9k, ath9k_htc and ath5k drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the remaining time in the current roc is not long
enough, mac80211 adds the new roc right after it
(if they have similar params).
However, in case of multiple rocs, the "next roc"
is not considered, resulting in multiple rocs,
each one with its own duration.
Refactor the code a bit and consider the next roc,
so a single max roc will be used instead of
multiple rocs (which might last much longer).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new duration (remaining duration after the current
ROC ends) was calculated but not used, making the
optimization worthless.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of a RRM-supporting connection, in the association request
frame: set the RRM capability flag, and add the required IEs.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function description claimed that on error the skb isn't
freed even though it is, and stated return values that are
different than what really happens in the code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta_set_sinfo is obviously takes data for specific station.
This specific station is attached to a specific virtual
interface. Hence we should use the dtim_period from this
virtual interface rather than the system wide dtim_period.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not sure how the declaration of ieee80211_tdls_peer_del_work
landed after the double inclusion protection end.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs.
-----BEGIN PGP SIGNATURE-----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=G/pB
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
Signed-off-by: John W. Linville <linville@redhat.com>
When starting an offloaded BA session it is
unknown what starting sequence number should be
used. Using last_seq worked in most cases except
after hw restart.
When hw restart is requested last_seq is
(rightfully so) kept unmodified. This ended up
with BA sessions being restarted with an aribtrary
BA window values resulting in dropped frames until
sequence numbers caught up.
Instead of last_seq pick seqno of a first Rxed
frame of a given BA session.
This fixes stalled traffic after hw restart with
offloaded BA sessions (currently only ath10k).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a device driver is unloaded local->interfaces
list is cleared. If there was more than 1
interface running and connected (bound to a
chanctx) then chantype recalc was called and it
ended up with compat being NULL causing a call
trace warning.
Warn if compat becomes NULL as a result of
incompatible bss_conf.chandef of interfaces bound
to a given channel context only.
The call trace looked like this:
WARNING: CPU: 2 PID: 2594 at /devel/src/linux/net/mac80211/chan.c:557 ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0()
Modules linked in: ath10k_pci(-) ath10k_core ath
CPU: 2 PID: 2594 Comm: rmmod Tainted: G W 3.16.0-rc1+ #150
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
0000000000000009 ffff88001ea279c0 ffffffff818dfa93 0000000000000000
ffff88001ea279f8 ffffffff810514a8 ffff88001ce09cd0 ffff88001e03cc58
0000000000000000 ffff88001ce08840 ffff88001ce09cd0 ffff88001ea27a08
Call Trace:
[<ffffffff818dfa93>] dump_stack+0x4d/0x66
[<ffffffff810514a8>] warn_slowpath_common+0x78/0xa0
[<ffffffff81051585>] warn_slowpath_null+0x15/0x20
[<ffffffff818a407d>] ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0
[<ffffffff818a3dda>] ? ieee80211_recalc_chanctx_chantype+0x2a/0x2e0
[<ffffffff818a4919>] ieee80211_assign_vif_chanctx+0x1a9/0x770
[<ffffffff818a6220>] __ieee80211_vif_release_channel+0x70/0x130
[<ffffffff818a6dd3>] ieee80211_vif_release_channel+0x43/0xb0
[<ffffffff81885f4e>] ieee80211_stop_ap+0x21e/0x5a0
[<ffffffff8184b9b5>] __cfg80211_stop_ap+0x85/0x520
[<ffffffff8181c188>] __cfg80211_leave+0x68/0x120
[<ffffffff8181c268>] cfg80211_leave+0x28/0x40
[<ffffffff8181c5f3>] cfg80211_netdev_notifier_call+0x373/0x6b0
[<ffffffff8107f965>] notifier_call_chain+0x55/0x110
[<ffffffff8107fa41>] raw_notifier_call_chain+0x11/0x20
[<ffffffff816a8dc0>] call_netdevice_notifiers_info+0x30/0x60
[<ffffffff816a8eb9>] __dev_close_many+0x59/0xf0
[<ffffffff816a9021>] dev_close_many+0x81/0x120
[<ffffffff816aa1c5>] rollback_registered_many+0x115/0x2a0
[<ffffffff816aa3a6>] unregister_netdevice_many+0x16/0xa0
[<ffffffff8187d841>] ieee80211_remove_interfaces+0x121/0x1b0
[<ffffffff8185e0e6>] ieee80211_unregister_hw+0x56/0x110
[<ffffffffa0011ac4>] ath10k_mac_unregister+0x14/0x60 [ath10k_core]
[<ffffffffa0014fe7>] ath10k_core_unregister+0x27/0x40 [ath10k_core]
[<ffffffffa003b1f4>] ath10k_pci_remove+0x44/0xa0 [ath10k_pci]
[<ffffffff81373138>] pci_device_remove+0x28/0x60
[<ffffffff814cb534>] __device_release_driver+0x64/0xd0
[<ffffffff814cbcc8>] driver_detach+0xb8/0xc0
[<ffffffff814cb23a>] bus_remove_driver+0x4a/0xb0
[<ffffffff814cc697>] driver_unregister+0x27/0x50
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "rcu_dereference()" calls are used directly in conditions.
Since their return values are never dereferenced it is recommended to
use "rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacements.
The following Coccinelle semantic patch was used:
@@
@@
(
if(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
|
while(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Header-less cloned skbs with sufficient headroom need not be cloned
unless the tailroom is going to be modified.
Fix ieee80211_skb_resize so it would only resize cloned skbs if either
the header isn't released or the tailroom is going to be modified.
Some drivers might have assumed that skbs are never cloned, so add a HW
flag that explicitly permits cloned TX skbs. Drivers which do not modify
TX skbs should set this flag to avoid copying skbs.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
will only require headroom space. Consequently, the tailroom-needed
counter can safely be decremented.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "RX active" string is too long, so the columns get
shifted. Change it to just "RX" to avoid this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta->last_seq_ctrl is the seq_ctrl field from the last header
seen, need to shift it 4 bits to extract the sequence number.
Otherwise the ieee80211_sn_less() check at the top of
ieee80211_sta_manage_reorder_buf drops frames until the sequence
number catches up.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 802.11 standard says when processing a plink confirm
frame:
"If the peerLinkID in the mesh peering instance has not been
set, the Local Link ID field of the Mesh Peering Confirm
request shall be copied into the peerLinkID in the mesh
peering instance."
We were only doing this when receiving an open peering frame,
but it could happen that the open frame gets lost and so we
should handle this case rather than rejecting the confirm and
failing the whole peering process.
Reported-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_sta_ps_deliver_wakeup, sdata->smps_mode is checked. This is
initialized only for the base AP interface, not the individual VLANs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When bringing down the AP, a WARN_ON is hit because the bss config chandef
is empty here.
Since AP_VLAN channel settings do not matter for anything chanctx related
(always inherits the settings from the AP interface), let's just ignore
it here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 24aa11ab8a.
That commit was wrong since it uses data that hasn't even been set
up yet, but might be a hold-over from a previous connection.
Additionally, it seems like a driver-specific workaround that
shouldn't have been in mac80211 to start with.
Cc: stable@vger.kernel.org
Fixes: 24aa11ab8a ("mac80211: disable uAPSD if all ACs are under ACM")
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new_ctx pointer is set only for non-chanctx drivers. This yielded a
crash for chanctx-based drivers during channel switch finalization:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]
Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the AP only advertises support for 20MHz (in the
ht operation ie), disable 40MHz and VHT.
This can improve interoperability with APs that
don't like stations exceeding their own
advertised capabilities.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently track the QoS capability twice: for all peer stations
in the WLAN_STA_WME flag, and for any clients associated to an AP
interface separately for drivers in the sta->sta.wme field.
Remove the WLAN_STA_WME flag and track the capability only in the
driver-visible field, getting rid of the limitation that the field
is only valid in AP mode.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the expected throughput is queried before rate control has been
initialized, the minstrel op for it will crash while trying to access
the rate table.
Check for WLAN_STA_RATE_CONTROL before attempting to use the rate
control op.
Reported-by: Jean-Pierre Tosoni <jp.tosoni@acksys.fr>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.
The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[fix endian bug]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (e.g. ath10k) report A-MSDU subframes
individually with identical seqno. The A-MPDU Rx
reorder code did not account for that which made
it practically unusable with drivers using
RX_FLAG_AMSDU_MORE because it would end up
dropping a lot of frames resulting in confusion in
upper network transport layers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sdata can't be NULL, and key being NULL is really not possible
unless the code is modified.
The sdata check made a static analyze (klocwork) unhappy because
we would get pointer to local (sdata->local) and only then check
if sdata is non-NULL.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove !key check as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NULL pointer access could happen when ieee80211_crypto_hw_decrypt
is called from ieee80211_rx_h_decrypt with the following condition:
1. rx->key->conf.cipher is not WEP, CCMP, TKIP or AES_CMAC
2. rx->sta is NULL
When ieee80211_crypto_hw_decrypt is called, it verifies
rx->sta->cipher_scheme and it will cause Oops if rx->sta is NULL.
This path adds an addirional rx->sta == NULL verification in
ieee80211_crypto_hw_decrypt for this case.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa_active flag was added in sdata a while ago and made
IEEE80211_STA_CSA_RECEIVED redundant. The new flag is also used to
mark when CSA is ongoing on other iftypes and took over the old one as
the preferred method for checking whether we're in the middle of a
channel switch. Remove the old, redundant flag.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the teardown packet is created while the queues are
stopped, it isn't sent immediately, but rather is pending.
To be sure that when we flush the queues prior to destroying
the station we also send this packet - the tasklet handling
pending packets is invoked to flush the packets.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: ArikX Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP receives actions frames destined for other peers, it may
mistakenly toggle BA-sessions from itself to a peer.
Ignore TDLS data packets as well - the AP should not handle them.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TDLS VHT support requires some more information elements during setup.
While these are not there, mask out the peer's VHT capabilities so that
VHT rates are not mistakenly used.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set for completeness mostly, currently unused in the code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the HT capabilities and HT operation information elements to TDLS
setup packets where appropriate.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can only be a station for TDLS connections. Also fix a bug where
a delayed work could be left scheduled if the station interface was
brought down during TDLS setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When TDLS QoS is supported by the the peer and the local card, add
the WMM parameter IE to the setup-confirm frame. Take the QoS settings
from the current AP, or if unsupported, use the default values from
the specification. This behavior is mandated by IEEE802.11-2012 section
10.22.4.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If QoS is supported by the card, add an appropriate IE to TDLS setup-
request and setup-response frames.
Consolidate the setting of the WMM info IE across mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending setup-failure frames, set the capability field to zero, as
mandated by the specification (IEEE802.11-2012 8.5.13).
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most setup-specific information elements are not to be added when a
setup frame is sent with an error status code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building TDLS setup frames, use the IE order mandates in the
specification, splitting extra IEs coming from usermode.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add all information elements for TDLS discovery and setup in the same
function.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "8f02e6b mac80211: make sure TDLS peer STA exists during
setup" broke TDLS error paths where the STA doesn't exist when sending
the error.
Fix it by only testing for STA existence during a non-error flow.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Infer the TDLS initiator and track it in mac80211 via a STA flag. This
avoids breaking old userspace that doesn't pass it via nl80211 APIs.
The only case where userspace will need to pass the initiator is when the
STA is removed due to unreachability before a teardown packet is sent.
Support for unreachability was only recently added to wpa_supplicant, so
it won't be a problem in practice.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When lockdep isn't compiled, a local variable isn't used
(it's only in a macro argument), annotate it to suppress
the compiler warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 277d916fc2 as it was
at least breaking iwlwifi by setting the IEEE80211_TX_CTL_NO_PS_BUFFER
flag in all kinds of interface modes, not only for AP mode where it is
appropriate.
To avoid reintroducing the original problem, explicitly check for probe
request frames in the multicast buffering code.
Cc: stable@vger.kernel.org
Fixes: 277d916fc2 ("mac80211: move "bufferable MMPDU" check to fix AP mode scan")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch finalization is now 2-step. First
step is when driver calls chswitch_done(), the
other is when reservation is actually finalized
(which be defered for in-place reservation).
It is now safe to call ieee80211_chswitch_done()
more than once.
Also remove the ieee80211_vif_change_channel()
because it is no longer used.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch finalization is now 2-step. First
step is when driver calls csa_finish(), the other
is when reservation is actually finalized (which
can be deferred for in-place reservation).
It is now safe to call ieee80211_csa_finish() more
than once.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_check_combinations() computes
radar_detect accordingly depending on chanctx
reservation status.
This makes it possible to use the function for
channel_switch validation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.
Such reservations are not finalized until all
assigned interfaces are ready.
This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.
This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).
As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.
As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After sending a TDLS discovery-request, we expect a reply to arrive on
the AP's channel. We must stay on the channel (no PSM, scan, etc.), since
a TDLS setup-response is a direct packet not buffered by the AP.
Add a new mac80211 driver callback to allow discovery session protection.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure userspace added a TDLS peer station before invoking the
transmission of the first setup frame. This ensures packets to the peer
won't go through the AP path.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Write a mac80211 to the cfg80211 API for requesting a userspace TDLS
operation. Define TDLS specific reason codes that can be used here.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the spec mandates, flush data in the AP path before transmitting the
first setup frame. Data packets transmitted during setup are already
dropped in the Tx path.
For the teardown flow, flush all packets in the direct path before
transmitting the teardown frame. Un-authorize the peer sta after teardown
is sent, forcing all subsequent Tx to the peer through the AP.
Make sure to flush the queues when disabling the link to get the
teardown packet out.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
[adjust to Luca's new quuee API and stop only vif queues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are setup/teardown specific actions to be done that accompany
the sending of a TDLS management packet. Split the main function to
simplify future additions.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Use the value from userspace in order to have a correct teardown packet.
With the current code, a teardown from the responder side fails the TDLS
MIC check because of a bad link identifier IE.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When setting up a TDLS session, register a delayed work to remove
the peer if setup times out. Prevent concurrent setups to support this
capacity.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For TDLS, the AUTHORIZED flag arrives with all other important station
info (supported rates, HT/VHT caps, ...). Make sure to set the station
state in the low-level driver after transferring this information to
the mac80211 STA entry.
This aligns the STA information during sta_state callbacks with the
non-TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename the flags used in the Tx path and add an explanation for the
reasons to drop, send directly or through the AP.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of stopping all the hardware queues during channel switch,
which is especially bad when we have large CSA counts, stop only the
queues that are assigned to the vif that is performing the channel
switch.
Additionally, check for (sdata->csa_block_tx) instead of calling
ieee80211_csa_needs_block_tx(), which can now be removed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases we may want to stop the queues of a single vif (for
instance during a channel-switch). Add a function that stops all the
queues that are assigned to a vif. If a queue is assigned to more
than one vif, the corresponding netdev subqueue of the other vif(s)
will also be stopped. If the HW doesn't set the
IEEE80211_HW_QUEUE_CONTROL flag, then all queues are stopped.
Also add a corresponding function to wake the queues of a vif back.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead. In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not. For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to stop all queues when we want to flush specific
queues, so stop only the queues that will be flushed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Converting time from one format to another seems to give coders a warm
and fuzzy feeling.
Use the proper interfaces.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John W. Linville <linville@tuxdriver.com>
[fix compile error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
do_posix_clock_monotonic_gettime() is a leftover from the initial
posix timer implementation which maps to ktime_get_ts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
vif->csa_active is protected by mutexes only. This
means it is unreliable to depend on it on codeflow
in non-sleepable beacon and CSA code. There was no
guarantee to have vif->csa_active update be
visible before beacons are updated on SMP systems.
Using csa counter offsets which are embedded in
beacon struct (and thus are protected with single
RCU assignment) is much safer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having csa counters part of beacon and probe_resp
structures makes it easier to get rid of possible
races between setting a beacon and updating
counters on SMP systems by guaranteeing counters
are always consistent against given beacon struct.
While at it relax WARN_ON into WARN_ON_ONCE to
prevent spamming logs and racing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[remove pointless array check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow send frames using monitor interface
when DFS chandef and we pass CAC (beaconing
allowed).
This fix problem when old kernel and new backports used,
in such case hostapd create/use also monitor interface.
Before this patch all frames hostapd send using monitor
iface were dropped when AP was configured on DFS channel.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh_plink code is doing some interesting things with the
ignore_plink_timer flag. It seems the original intent was to
handle this race:
cpu 0 cpu 1
----- -----
start timer handler for state X
acquire sta_lock
change state from X to Y
mod_timer() / del_timer()
release sta_lock
acquire sta_lock
execute state Y timer too soon
However, using the mod_timer()/del_timer() return values to
detect these cases is broken. As a result, timers get ignored
unnecessarily, and stations can get stuck in the peering state
machine.
Instead, we can detect the case by looking at the timer expiration.
In the case of del_timer, just ignore the timers in the following
(LISTEN/ESTAB) states since they won't have timers anyway.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is currently possible to have a race due to the station PS
unblock work like this:
* station goes to sleep with frames buffered in the driver
* driver blocks wakeup
* station wakes up again
* driver flushes/returns frames, and unblocks, which schedules
the unblock work
* unblock work starts to run, and checks that the station is
awake (i.e. that the WLAN_STA_PS_STA flag isn't set)
* we process a received frame with PM=1, setting the flag again
* ieee80211_sta_ps_deliver_wakeup() runs, delivering all frames
to the driver, and then clearing the WLAN_STA_PS_DRIVER and
WLAN_STA_PS_STA flags
In this scenario, mac80211 will think that the station is awake,
while it really is asleep, and any TX'ed frames should be filtered
by the device (it will know that the station is sleeping) but then
passed to mac80211 again, which will not buffer it either as it
thinks the station is awake, and eventually the packets will be
dropped.
Fix this by moving the clearing of the flags to exactly where we
learn about the situation. This creates a problem of reordering,
so introduce another flag indicating that delivery is being done,
this new flag also queues frames and is cleared only while the
spinlock is held (which the queuing code also holds) so that any
concurrent delivery/TX is handled correctly.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minstrel has long since proven its worth.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After skb allocation and call to ieee80211_wep_encrypt in ieee80211_send_auth
the flow fails with a warning in ieee80211_wep_add_iv on verification of
available head/tailroom needed for WEP_IV and WEP_ICV.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville