UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Cc: stable@vger.kernel.org
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
Move pxamci to mmc slot-gpio API to fix interrupt request.
It fixes the case where the card detection is on a gpio expander, on I2C
for example on zylonite board. In this case, the card detect netsted
interrupt is called from a threaded interrupt. The request_irq() fails,
because a hard irq cannot be a nested interrupt from a threaded
interrupt (set __setup_irq()).
This was tested on zylonite and mioa701 boards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In recent allwinner kernel sources the mmc clk-delay settings have been
slightly tweaked, and for sun9i they are completely different then what
we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk)
This also drops the clk-delay calculation for clocks > 50 MHz, we do
not need this as we've: mmc->f_max = 50000000, and the delays in the
old code were not correct (at 100 MHz the delay must be a multiple of 60,
at 200 MHz a multiple of 120).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CONFIG_GPIOLIB is unset, its stubs will return -ENOSYS. That means
when the mmc core parses DT for CD/WP GPIOs via mmc_of_parse(), -ENOSYS
becomes propagated to the caller. Typically this means that the mmc host
driver fails to probe.
As the CD/WP GPIOs are already treated as optional, let's extend that to
cover the case when CONFIG_GPIOLIB is unset.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Fixes: 16b23787fc ("mmc: sdhci-of-arasan: Call OF parsing for MMC")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Seemingly innocuous sctp_trans_state_to_prio_map[] array
is way bigger than it looks, since
"[SCTP_UNKNOWN] = 2" expands into "[0xffff] = 2" !
This patch replaces it with switch() statement.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
CC: linux-sctp@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small chance that tunnel_free() is called before tunnel->del_work scheduled
resulting in a zero pointer dereference.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the MAC register dump used to be the size specified by the
reg property in the device tree. Userland has no good way of finding
out that size, and it was not specified consistently for each MAC type,
so ethtool would end up printing junk at the end of the register dump
if the device tree didn't match the size it assumed.
Using the new version numbers indicates unambiguously that the size of
the MAC register dump is dependent only on the MAC type.
Fixes: 5369c71f7c ("net/ibm/emac: fix size of emac dump memory areas")
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karl Heiss says:
====================
sctp: Fix SCTP deadlock
These patches fix a deadlock during accept() of an SCTP connection.
The first patch fixes whitespace issues.
The second patch actually fixes the deadlock race.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A case can occur when sctp_accept() is called by the user during
a heartbeat timeout event after the 4-way handshake. Since
sctp_assoc_migrate() changes both assoc->base.sk and assoc->ep, the
bh_sock_lock in sctp_generate_heartbeat_event() will be taken with
the listening socket but released with the new association socket.
The result is a deadlock on any future attempts to take the listening
socket lock.
Note that this race can occur with other SCTP timeouts that take
the bh_lock_sock() in the event sctp_accept() is called.
BUG: soft lockup - CPU#9 stuck for 67s! [swapper:0]
...
RIP: 0010:[<ffffffff8152d48e>] [<ffffffff8152d48e>] _spin_lock+0x1e/0x30
RSP: 0018:ffff880028323b20 EFLAGS: 00000206
RAX: 0000000000000002 RBX: ffff880028323b20 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff880028323be0 RDI: ffff8804632c4b48
RBP: ffffffff8100bb93 R08: 0000000000000000 R09: 0000000000000000
R10: ffff880610662280 R11: 0000000000000100 R12: ffff880028323aa0
R13: ffff8804383c3880 R14: ffff880028323a90 R15: ffffffff81534225
FS: 0000000000000000(0000) GS:ffff880028320000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000000006df528 CR3: 0000000001a85000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff880616b70000, task ffff880616b6cab0)
Stack:
ffff880028323c40 ffffffffa01c2582 ffff880614cfb020 0000000000000000
<d> 0100000000000000 00000014383a6c44 ffff8804383c3880 ffff880614e93c00
<d> ffff880614e93c00 0000000000000000 ffff8804632c4b00 ffff8804383c38b8
Call Trace:
<IRQ>
[<ffffffffa01c2582>] ? sctp_rcv+0x492/0xa10 [sctp]
[<ffffffff8148c559>] ? nf_iterate+0x69/0xb0
[<ffffffff814974a0>] ? ip_local_deliver_finish+0x0/0x2d0
[<ffffffff8148c716>] ? nf_hook_slow+0x76/0x120
[<ffffffff814974a0>] ? ip_local_deliver_finish+0x0/0x2d0
[<ffffffff8149757d>] ? ip_local_deliver_finish+0xdd/0x2d0
[<ffffffff81497808>] ? ip_local_deliver+0x98/0xa0
[<ffffffff81496ccd>] ? ip_rcv_finish+0x12d/0x440
[<ffffffff81497255>] ? ip_rcv+0x275/0x350
[<ffffffff8145cfeb>] ? __netif_receive_skb+0x4ab/0x750
...
With lockdep debugging:
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
CslRx/12087 is trying to release lock (slock-AF_INET) at:
[<ffffffffa01bcae0>] sctp_generate_timeout_event+0x40/0xe0 [sctp]
but there are no more locks to release!
other info that might help us debug this:
2 locks held by CslRx/12087:
#0: (&asoc->timers[i]){+.-...}, at: [<ffffffff8108ce1f>] run_timer_softirq+0x16f/0x3e0
#1: (slock-AF_INET){+.-...}, at: [<ffffffffa01bcac3>] sctp_generate_timeout_event+0x23/0xe0 [sctp]
Ensure the socket taken is also the same one that is released by
saving a copy of the socket before entering the timeout event
critical section.
Signed-off-by: Karl Heiss <kheiss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that while we are waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If we then attempt to use the queue, we will panic.
Add a check for this condition on the receive side. This matches
an existing check on the send queue side.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously to this patch, the hardware was removing
VLAN tags from the inner header of VXLAN packets. The
hardware configuration can be changed to leave the
packet alone since that is what the linux stack
expects for this type of VLAN in VXLAN packet.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It uses bitrev8(), so it must ensure that lib/bitrev.o gets included in
vmlinux.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If omap4_keypad_parse_dt() fails we returned the error code but we
missed releasing keypad_data.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sanitizing the e820 map may produce extra E820 entries which would result in
the topmost E820 entries being removed. The removed entries would typically
include the top E820 usable RAM region and thus result in the domain having
signicantly less RAM available to it.
Fix by allowing sanitize_e820_map to use the full size of the allocated E820
array.
Signed-off-by: Malcolm Crossley <malcolm.crossley@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Pull arch/tile bugfix from Chris Metcalf:
"This fixes a bug in 'make allmodconfig'"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: fix build failure
When building with allmodconfig the build was failing with the error:
arch/tile/kernel/usb.c:70:1: warning: data definition has no type or storage class [enabled by default]
arch/tile/kernel/usb.c:70:1: error: type defaults to 'int' in declaration of 'arch_initcall' [-Werror=implicit-int]
arch/tile/kernel/usb.c:70:1: warning: parameter names (without types) in function declaration [enabled by default]
arch/tile/kernel/usb.c:63:19: warning: 'tilegx_usb_init' defined but not used [-Wunused-function]
Include linux/module.h to resolve the build failure.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Otherwise a FRMR completion can cause a touch-after-free crash.
In xprt_rdma_destroy(), call rpcrdma_buffer_destroy() only after calling
rpcrdma_ep_destroy().
In rpcrdma_ep_destroy(), disconnect the cm_id first which should flush the
qp, then drain the cqs, then destroy the qp, and finally destroy the cqs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
A previous commit resets the Context Status Buffer (CSB) read pointer in
ring init
commit c0a03a2e4c ("drm/i915: Reset CSB read pointer in ring init")
This is generally correct, but this pointer is not reset after
suspend/resume in some platforms (cht). In this case, the driver should
read the register value instead of resetting the sw read counter to 0.
Otherwise we process old events, leading to unwanted pre-emptions or
something worse.
But in other platforms (bdw) and also during GPU reset or power up, the
CSBWP is reset to 0x7 (an invalid number), and in this case the read
pointer should be set to 5 (the interrupt code will increment this
counter one more time, and will start reading from CSB[0]).
v2: When the CSB registers are reset, the read pointer needs to be set
to 5, otherwise the first write (CSB[0]) won't be read (Mika).
Replace magic numbers with GEN8_CSB_ENTRIES (6) and GEN8_CSB_PTR_MASK
(0x07).
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Lei Shen <lei.shen@intel.com>
Signed-off-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently there is a number of issues preventing PVHVM Xen guests from
doing successful kexec/kdump:
- Bound event channels.
- Registered vcpu_info.
- PIRQ/emuirq mappings.
- shared_info frame after XENMAPSPACE_shared_info operation.
- Active grant mappings.
Basically, newly booted kernel stumbles upon already set up Xen
interfaces and there is no way to reestablish them. In Xen-4.7 a new
feature called 'soft reset' is coming. A guest performing kexec/kdump
operation is supposed to call SCHEDOP_shutdown hypercall with
SHUTDOWN_soft_reset reason before jumping to new kernel. Hypervisor
(with some help from toolstack) will do full domain cleanup (but
keeping its memory and vCPU contexts intact) returning the guest to
the state it had when it was first booted and thus allowing it to
start over.
Doing SHUTDOWN_soft_reset on Xen hypervisors which don't support it is
probably OK as by default all unknown shutdown reasons cause domain
destroy with a message in toolstack log: 'Unknown shutdown reason code
5. Destroying domain.' which gives a clue to what the problem is and
eliminates false expectations.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
For PV guests these registers are set up by hypervisor and thus
should not be written by the guest. The comment in xen_write_msr_safe()
says so but we still write the MSRs, causing the hypervisor to
print a warning.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
HYPERVISOR_memory_op() is defined to return an "int" value. This is
wrong, as the Xen hypervisor will return "long".
The sub-function XENMEM_maximum_reservation returns the maximum
number of pages for the current domain. An int will overflow for a
domain configured with 8TB of memory or more.
Correct this by using the correct type.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Shifting pvclock_vcpu_time_info.system_time on write to KVM system time
MSR is a change of ABI. Probably only 2.6.16 based SLES 10 breaks due
to its custom enhancements to kvmclock, but KVM never declared the MSR
only for one-shot initialization. (Doc says that only one write is
needed.)
This reverts commit b7e60c5aed.
And adds a note to the definition of PVCLOCK_COUNTS_FROM_ZERO.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If I2C is built as module, the iTCO watchdog driver must be built as module
as well. I2C_I801 must only be selected if I2C is configured.
This fixes the following build errors, seen if I2C=m and ITCO_WDT=y.
i2c-i801.c:(.text+0x2bf055): undefined reference to `i2c_del_adapter'
i2c-i801.c:(.text+0x2c13e0): undefined reference to `i2c_add_adapter'
i2c-i801.c:(.text+0x2c17bd): undefined reference to `i2c_new_device'
Fixes: 2a7a0e9bf7 ("watchdog: iTCO_wdt: Add support for TCO on Intel Sunrisepoint")
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently poweroff/halt results in a reboot on the Raspberry Pi.
The firmware uses the RSTS register to know which partiton to
boot from. The partiton value is spread into bits
0, 2, 4, 6, 8, 10. Partiton 63 is a special partition used by
the firmware to indicate halt.
The firmware made this change in 19 Aug 2013 and was matched
by the downstream commit:
Changes for new NOOBS multi partition booting from gsh
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make sure the compiler does not modify arguments of syscall functions.
This can happen if the compiler generates a tailcall to another
function. For example, without asmlinkage_protect sys_openat is compiled
into this function:
sys_openat:
clr.l %d0
move.w 18(%sp),%d0
move.l %d0,16(%sp)
jbra do_sys_open
Note how the fourth argument is modified in place, modifying the register
%d4 that gets restored from this stack slot when the function returns to
user-space. The caller may expect the register to be unmodified across
system calls.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Pull RCU fixes from Paul E. McKenney, for two regressions
introduced in this merge window:
- Fix bug with recent GCCs.
- Fix false positive lockdep splat.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If parkbd_allocate_serio() fails to allocate memory we are releasing the
parport but we missed unregistering the device. As a result this device
with exclusive access to that parport remains registered. And no other
device will be able to use that parport even though this driver has
failed to load.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull MIPS fixes from Ralf Baechle:
- Properly setup irq handling for ATH79 platforms
- Fix bootmem mapstart calculation for contiguous maps
- Handle little endian and older CPUs correct in BPF
- Fix console for Fulong 2E systems
- Handle FTLB correctly on R6 CPUs
- Fixes for CM, GIC and MAAR support code
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Initialise MAARs on secondary CPUs
MIPS: print MAAR configuration during boot
MIPS: mm: compile maar_init unconditionally
irqchip: mips-gic: Fix pending & mask reads for MIPS64 with 32b GIC.
irqchip: mips-gic: Convert CPU numbers to VP IDs.
MIPS: CM: Provide a function to map from CPU to VP ID.
MIPS: Fix FTLB detection for R6
MIPS: cpu-features: Add cpu_has_ftlb
MIPS: ATH79: Add irq chip ar7240-misc-intc
MIPS: ATH79: Set missing irq ack handler for ar7100-misc-intc irq chip
MIPS: BPF: Fix build on pre-R2 little endian CPUs
MIPS: BPF: Avoid unreachable code on little endian
MIPS: bootmem: Fix mapstart calculation for contiguous maps
MIPS: Fix console output for Fulong2e system
Pull perf fixes from Thomas Gleixner:
"Another pile of fixes for perf:
- Plug overflows and races in the core code
- Sanitize the flow of the perf syscall so we error out before
handling the more complex and hard to undo setups
- Improve and fix Broadwell and Skylake hardware support
- Revert a fix which broke what it tried to fix in perf tools
- A couple of smaller fixes in various places of perf tools"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Fix copying of /proc/kcore
perf intel-pt: Remove no_force_psb from documentation
perf probe: Use existing routine to look for a kernel module by dso->short_name
perf/x86: Change test_aperfmperf() and test_intel() to static
tools lib traceevent: Fix string handling in heterogeneous arch environments
perf record: Avoid infinite loop at buildid processing with no samples
perf: Fix races in computing the header sizes
perf: Fix u16 overflows
perf: Restructure perf syscall point of no return
perf/x86/intel: Fix Skylake FRONTEND MSR extrareg mask
perf/x86/intel/pebs: Add PEBS frontend profiling for Skylake
perf/x86/intel: Make the CYCLE_ACTIVITY.* constraint on Broadwell more specific
perf tools: Bool functions shouldn't return -1
tools build: Add test for presence of __get_cpuid() gcc builtin
tools build: Add test for presence of numa_num_possible_cpus() in libnuma
Revert "perf symbols: Fix mismatched declarations for elf_getphdrnum"
perf stat: Fix per-pkg event reporting bug
Pull scheduler fix from Thomas Gleixner:
"A single bug fix for the scheduler to prevent dequeueing of the idle
task when setting the cpus allowed mask"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix crash trying to dequeue/enqueue the idle thread
Pull locking fix from Thomas Gleixner:
"A single bugfix for lockdep to preserve the pinning counter when
rebuilding the lock stack"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Fix hlock->pin_count reset on lock stack rebuilds
Pull turbostat updates for v4.3 from Len Brown.
* 'turbostat' of https://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbosat: update version number
tools/power turbostat: SKL: Adjust for TSC difference from base frequency
tools/power turbostat: KNL workaround for %Busy and Avg_MHz
tools/power turbostat: IVB Xeon: fix --debug regression
MAARs should be initialised on each CPU (or rather, core) in the system
in order to achieve consistent behaviour & performance. Previously they
have only been initialised on the boot CPU which leads to performance
problems if tasks are later scheduled on a secondary CPU, particularly
if those tasks make use of unaligned vector accesses where some CPUs
don't handle any cases in hardware for non-speculative memory regions.
Fix this by recording the MAAR configuration from the boot CPU and
applying it to secondary CPUs as part of their bringup.
Reported-by: Doug Gilmore <doug.gilmore@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Hemmo Nieminen <hemmo.nieminen@iki.fi>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Verifying that the MAAR configuration is as expected is useful when
debugging the performance of a system. Print out the memory regions
configured via MAAR along with their attributes.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
maar_init was previously only compiled when CONFIG_NEED_MULTIPLE_NODES
was not set, which has been fine since it is only called from the
standard implementation of mem_init which has the same condition. In
preparation for calling it from the SMP startup code on secondary CPUs,
move maar_init outside of the #ifndef such that it is always compiled.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/11237/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
gic_handle_shared_int reads the GIC interrupt pending & mask registers
directly into a bitmap, which is defined as an array of unsigned longs.
The GIC pending registers may be 32 bits wide if the CM is older than
CM3, regardless of the bit width of the CPU, but for MIPS64 kernels
the unsigned longs in the bitmap will be 64 bits wide. In this case we
need to perform 2 x 32 bit reads per 64 bit unsigned long in order to
avoid missing interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11213/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the mips_cm_vp_id function to convert from Linux CPU numbers
to the VP IDs used by hardware, which are not identical in all systems.
Without doing so we map interrupts to incorrect VP(E)s.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11212/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
