The userspace interface for acceleration sensors is documented as using
m/s^2 units [Documentation/ABI/testing/sysfs-bus-iio]
The fullscale raw value for the mma8452 (-2048) corresponds to -2G, -4G or -8G
depending on the seleted mode.
The scale table was converting to G rather than m/s^2.
Change the scaling table to match the documented interface.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: stable@vger.kernel.org
When event spec is shared by multiple channels, which has definition
for mask_shared_by_type, iio_device_register_eventset fails.
For example:
static const struct iio_event_spec iio_dummy_events[] = {
{
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_RISING,
.mask_separate = BIT(IIO_EV_INFO_ENABLE),
.mask_shared_by_type = BIT(IIO_EV_INFO_VALUE),
}, {
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_FALLING,
.mask_separate = BIT(IIO_EV_INFO_ENABLE),a
.mask_shared_by_type = BIT(IIO_EV_INFO_VALUE),
}
};
If two channels use this event spec, this will result in error.
This change handles EBUSY error similar to iio_device_add_info_mask_type().
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
Since AI lines could be selected at will (linux-3.11) the sending
and receiving ends of the FIFO does not agree about what step is used
for a line. It only works if the last lines are used, like 5,6,7,
and fails if ie 2,4,6 is selected in DT.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Tested-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: stable@vger.kernel.org
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Agreed with by Srinivas.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently in the inkern.c code for IIO framework, the function
of_iio_channel_get_by_name() will return a non-NULL pointer when
it cannot find a channel using of_iio_channel_get() and when it
tries to search for 'io-channel-ranges' property and fails. This
is incorrect behaviour as the function which calls this expects
a NULL pointer for failure. This patch rectifies the issue.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
last two bits of ADC and limit values are zero and should not be reported
(ad7993, ad7997); compare with read_raw()
event values are 10 (ad7993, ad7997) or 12 bit max., check the range on write
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Stable@vger.kernel.org
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A mixed bag of fixes, many of which feel just to late for 3.15.
* hid sensors - some devices need a feature report request in order to
change power state. This isn't part of the spec, but has been observed
on several devices and does no harm to others.
* mpl3115 has had two errors in the buffer description fixed. The presure is
signed, not unsigned and the temperature has 12 bits rather than 16.
These could lead to incorrect interpretation of the data in userspace.
* tsl2x7x - the high byte of the proximity thresholds should be written along
with the low byte (which was). This could lead to interesting results
with large thresholds.
* twl4030 - a flag to specify processed values were required was not set
when initializing a reading. As such values returned were in an unknown
state. Fixed by simply initializing it appropriately.
* IIO_SIMPLE_DUMMY_BUFFER did not select IIO_BUFFER leading to randconfig
build errors.
* ak8975 was applying an unwanted le16_to_cpu conversion as the i2c framework
already performs one. As such for big endian systems, the bytes would be
in the wrong order in the magnetic field measurements reported.
* mxs-lradc - the controllable voltage dividers were not enabled / disabled for
later channels than the first one during conversion.
* at91_adc error handling returned -ENOMEM in a u8. Return value of
at91_adc_get_trigger_value_by_name changed to int thus allowing -ENOMEM and
also original values to be returned.
* mcb - mcb_request_mem returns and ERR_PTR but the caller was checking for
NULL to detect an error.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RuB2
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 3.16 cycle.
A mixed bag of fixes, many of which feel just to late for 3.15.
* hid sensors - some devices need a feature report request in order to
change power state. This isn't part of the spec, but has been observed
on several devices and does no harm to others.
* mpl3115 has had two errors in the buffer description fixed. The presure is
signed, not unsigned and the temperature has 12 bits rather than 16.
These could lead to incorrect interpretation of the data in userspace.
* tsl2x7x - the high byte of the proximity thresholds should be written along
with the low byte (which was). This could lead to interesting results
with large thresholds.
* twl4030 - a flag to specify processed values were required was not set
when initializing a reading. As such values returned were in an unknown
state. Fixed by simply initializing it appropriately.
* IIO_SIMPLE_DUMMY_BUFFER did not select IIO_BUFFER leading to randconfig
build errors.
* ak8975 was applying an unwanted le16_to_cpu conversion as the i2c framework
already performs one. As such for big endian systems, the bytes would be
in the wrong order in the magnetic field measurements reported.
* mxs-lradc - the controllable voltage dividers were not enabled / disabled for
later channels than the first one during conversion.
* at91_adc error handling returned -ENOMEM in a u8. Return value of
at91_adc_get_trigger_value_by_name changed to int thus allowing -ENOMEM and
also original values to be returned.
* mcb - mcb_request_mem returns and ERR_PTR but the caller was checking for
NULL to detect an error.
at91_adc_get_trigger_value_by_name() was returning -ENOMEM truncated to
a positive u8 and that doesn't work. I've changed it to int and
refactored it to preserve the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
i2c_smbus_read_word_data() does host endian conversion already,
no need for le16_to_cpu()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
Here is the big staging driver pull request for 3.16-rc1.
Lots of stuff here, tons of cleanup patches, a few new drivers, and some
removed as well, but I think we are still adding a few thousand more
lines than we remove, due to the new drivers being bigger than the ones
deleted.
One notible bit of work did stand out, Jes Sorensen has gone on a tear,
fixing up a wireless driver to be "more sane" than it originally was
from the vendor, with over 500 patches merged here. Good stuff, and a
number of users laptops are better off for it.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONXKQACgkQMUfUDdst+ynIwgCgq5pPIn+2aewaFK8rrN18xqls
F3YAoNDYeqMpQepvRe50HcjRrgDvsV2n
=VenO
-----END PGP SIGNATURE-----
Merge tag 'staging-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging into next
Pull staging driver updates from Greg KH:
"Here is the big staging driver pull request for 3.16-rc1.
Lots of stuff here, tons of cleanup patches, a few new drivers, and
some removed as well, but I think we are still adding a few thousand
more lines than we remove, due to the new drivers being bigger than
the ones deleted.
One notible bit of work did stand out, Jes Sorensen has gone on a
tear, fixing up a wireless driver to be "more sane" than it originally
was from the vendor, with over 500 patches merged here. Good stuff,
and a number of users laptops are better off for it.
All of this has been in linux-next for a while"
* tag 'staging-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1703 commits)
staging: skein: fix sparse warning for static declarations
staging/mt29f_spinand: coding style fixes
staging: silicom: fix sparse warning for static variable
staging: lustre: Fix coding style
staging: android: binder.c: Use more appropriate functions for euid retrieval
staging: lustre: fix integer as NULL pointer warnings
Revert "staging: dgap: remove unneeded kfree() in dgap_tty_register_ports()"
Staging: rtl8192u: r8192U_wx.c Fixed a misplaced brace
staging: ion: shrink highmem pages on kswapd
staging: ion: use compound pages on high order pages for system heap
staging: ion: remove struct ion_page_pool_item
staging: ion: simplify ion_page_pool_total()
staging: ion: tidy up a bit
staging: rtl8723au: Remove redundant casting in usb_ops_linux.c
staging: rtl8723au: Remove redundant casting in rtl8723a_hal_init.c
staging: rtl8723au: Remove redundant casting in rtw_xmit.c
staging: rtl8723au: Remove redundant casting in rtw_wlan_util.c
staging: rtl8723au: Remove redundant casting in rtw_sta_mgt.c
staging: rtl8723au: Remove redundant casting in rtw_recv.c
staging: rtl8723au: Remove redundant casting in rtw_mlme.c
...
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Not setting the raw parameter in the request causes it to be randomly
initialized to a value that might be different from zero or zero. This leads to
values that are randomly either raw or processed, making it very difficult to
make reliable use of the values.
Cc: Stable@vger.kernel.org
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
(i) pressure is 20-bit unsigned, not signed; the buffer description
is incorrect; for raw reads, this is just cosmetic
(ii) temperature is 12-bit signed, not 16-bit; this affects
readout of temperatures below zero as the sign bit is incorrectly
processed
reported via private mail
Cc: stable@vger.kernel.org
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: Robert Deliën <robert@delien.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some sensor hubs require a get feature report call to be issued soon after
changing the power state of the sensor. Without this, the sensor remains in
the current state. This patch adds a call soon after the power state.
This is retained as a generic call across all sensor hubs since the behavior
has been noticed on more than one implementation.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This (rather late) set consists only of fixes to patches earlier in the
cycle or minor fixes for other problems (such as randconfig build issues
picked up by Arnd). I've included the general minor fixes here as it is
very late in the current cycle and they can all wait for the merge window.
* Recent change to hid-sensors introduced a possible infinite loop due to a
typo. In the same series, a report interval unit read was added but in the
case where the hardware doesn't support it a value of 0 would lead to some
nasty issues. The patch sets it to the specified default of msecs.
* Anon inodes were used by IIO without being explicitly selected. This has
been true for a long time so it clearly only effects rather unusual
configurations (rand configs)
* at91 requires the input subsytem but this wasn't explicity in the Kconfig.
* A couple of parts supported by the max1363 driver were using the wrong
iio_chan_spec arrays and hence would missreport their bit depths. This has
been there a long time and was never right so isn't a regression.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJTgdLAAAoJEFSFNJnE9BaIDBwP/jGJ4cOV4mKekQvn+keMCQ8M
fPyKRijwgWE9VEVP6BbhA5ya4hwH6bloQXBBp2PhB51GS1I8pNc5dWJzQEZO+oFA
9jkQm91zufeRjxEUCRlD8kfJ+7V766SKlIkENbJgbk5XStvrAWAIQ8lHkHwJmL5j
lNfGWCrVuBKK3Ck08HH6p2N6hHO1GDHnyrdGIW2BYJZVyUBpBlkukSZoU8T0zB6g
F9QzZyECG9VdbL1HVBrsBy3Pw9cOwiMTJrDMJ2dkwBdKmAnkllSomrKV5cOlYWFF
qg3z6JOPPY+6Hpl15tr2RvTaoKYTc33q9/UX1sysrLyLN07W52ygXdozxTGUINB2
ozhmIp/oZVYyHXIHC3yg7MOhW6AExJkzr91IMNnvVT8f22BlkdXHRB0atCAHcUvT
t4NsFHS0QrRYooqVI12Z3wOPmZahydgUlivNySRaug4lYgULxl5pts9WAl8fEgA7
ZM4tUUtGjrni5KpaYT5wnQ2JhwNTZDu2kIYgRB5Zhh5F/uqJ/xQCjllhJxv92hKG
r6LvacGaWiwyYXryl4TvfqH1/4lqsFk8nyS0OLUFhtCfE8jmydSZ63LhnnQJs/iH
u0u/uDz9lqPgtClWZDm3YqIMRpp4ShNkn8irBZ9bLhaHC59GurgYMM+PgkrUPM/N
7y76UVWNYNWxYb/L0A5n
=u2ra
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.16c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third round of new stuff for IIO in the 3.16 cycle.
This (rather late) set consists only of fixes to patches earlier in the
cycle or minor fixes for other problems (such as randconfig build issues
picked up by Arnd). I've included the general minor fixes here as it is
very late in the current cycle and they can all wait for the merge window.
* Recent change to hid-sensors introduced a possible infinite loop due to a
typo. In the same series, a report interval unit read was added but in the
case where the hardware doesn't support it a value of 0 would lead to some
nasty issues. The patch sets it to the specified default of msecs.
* Anon inodes were used by IIO without being explicitly selected. This has
been true for a long time so it clearly only effects rather unusual
configurations (rand configs)
* at91 requires the input subsytem but this wasn't explicity in the Kconfig.
* A couple of parts supported by the max1363 driver were using the wrong
iio_chan_spec arrays and hence would missreport their bit depths. This has
been there a long time and was never right so isn't a regression.
This resolves the conflicts in the files:
drivers/iio/adc/Kconfig
drivers/staging/rtl8723au/os_dep/usb_ops_linux.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For PROP_REPORT_INTERVAL, the spec does not mandate the presence
of the report interval unit in the feature report and expects the
default unit of measure to be used as milliseconds.
Currently, when the unit is not present, it gets set as zero leading
to issues in sampling frequency.
This patch sets the unit of measure to the default unit if it
is not defined by firmware.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Building the at91 adc driver with CONFIG_INPUT disabled results in this
build error:
ERROR: "input_event" [drivers/iio/adc/at91_adc.ko] undefined!
ERROR: "input_unregister_device" [drivers/iio/adc/at91_adc.ko] undefined!
ERROR: "input_free_device" [drivers/iio/adc/at91_adc.ko] undefined!
ERROR: "input_register_device" [drivers/iio/adc/at91_adc.ko] undefined!
ERROR: "input_set_abs_params" [drivers/iio/adc/at91_adc.ko] undefined!
ERROR: "input_allocate_device" [drivers/iio/adc/at91_adc.ko] undefined!
To make sure we can build random configurations, this adds a Kconfig
dependency on CONFIG_INPUT, as we do for other similar drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-iio@vger.kernel.org
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Without ANON_INODES, we get this build error:
drivers/built-in.o: In function `iio_event_getfd':
:(.text+0x14bf18): undefined reference to `anon_inode_getfd'
All other users explicitly select this symbol, so we should
do the same thing here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The "i < " was missing in this condition.
Fixes: 5d02edfc39 ('iio: hid-sensors: Convert units and exponent')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
That include file is now only used by the at91_adc driver, remove it from
include/mach for better driver separation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Old ADCs, as present on the sam9rl and the sam9g45 don't have a TSMR register
and the touchscreen support should be handled differently.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
num_channels and registers are not used anymore since they are defined inside
the driver and assigned by matching the id_table.
Also, struct at91_adc_reg_desc is now only used inside the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added an API to allow client drivers to turn ON and OFF sensors for
quick read. Added data_read as counting varaible instead of boolean,
so that sensor is powered off only when last user released it.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using units and unit exponent to calculate scale which is compliant
to IIO ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using units and unit exponent to calculate scale which is compliant
to IIO ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using units and unit exponent to calculate scale which is compliant
to IIO ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using units and unit exponent to calculate scale which is compliant
to IIO ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using units and unit exponent to calculate scale which is compliant
to IIO ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using units and unit exponent to calculate scale which is compliant
to IIO ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added interface to get poll value in milli-seconds. This value is
changed by changing sampling frequency. This API allows clients
to wait for at least some poll milli seconds before reading a new sample.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
HID sensor hub specify a default unit and alternative units. This
along with unit exponent can be used adjust scale. This change
change HID sensor data units to IIO defined units for each
sensor type. So in this way user space can use a simply use:
"(data + offset) * scale" to get final result.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
3-axis accelerometer sensor (2/4/8 g) with 12-bit resolution
and I2C interface
many extra features are unsupported (freefall detection, orientation
change, autosleep)
datasheet is here:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8452Q.pdf
v2: (thanks to Jonathan Cameron)
* use ARRAY_SIZE()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixing issue caused by clash of two patches, one adding a name with
the acpi enumeration patch.
54ab3e24 Beomho Seo 2014-04-02 @572 indio_dev->name = id->name;
d913971e Srinivas Pandruvada 2014-03-19 574 indio_dev->name = name;
The name added by commit 54ab3e24 is not required as this is already
added by taking care of case where id is NULL.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Martin Fuzzey