It turned out that the FLOAT format on CS4206 results in simple
noises, which implies that this is no right format as is.
Since CS4206 is the only codec supporting the float, let's disable it
until we find the correct format.
Reported-and-tested-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp and caps hashes aren't protected properly for concurrent
accesses. Protect them via a new mutex now.
But it can't be so simple as originally thought: since the update of a
hash table entry itself might trigger the power-up sequence which
again accesses the hash table, we can't cover the whole function
simply via mutex. Thus the update part has to be split from the mutex
and revalidated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the power_transition up/down state instead of boolean bit, so
that the power-up sequence can cancel the pending power-down work
properly. Also, by moving cancel_delayed_work_sync() before the
actual power-up sequence, make sure that the delayed power-down is
completed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent commit, the resume procedure is always performed at
the resume time. This makes the pre_resume hack for VREF mute LED on
some HP laptops superfluous. As this is the only user of pre_resume
(and there is no user of post_suspend) ops, let's kill them again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some power-saving states have been left unchanged in
snd_hda_codec_reset(), and this is a potential danger because the
function may be called in various situations including the continuous
operation after that call.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a fix for the problem in commit 785f857d1c, the pop noise
issue on some machines with ALC269. The problem was the uninitialized
state after the resume due to the delayed resume of the codec chips.
In that commit, we tried to fix by forcibly putting the codec to D3 at
suspend. But, this still also leaves the uninitialized state after
resume, and it _might_ be still problematic with some BIOS. Since the
commit turned out to regress another issues, we reverted it in the
end.
Now, in this fix, try to fix by turning on the codec immediately at
the resume path. We need to take care of the power-saving in this
case. When the device is woken up at the power-saved state, it should
go power-saving again after the resume.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 785f857d1c.
The commit causes a problem with the wrong D3 state after suspend
because the call of hda_set_power_state() involves with the power-up
sequence, which changes the power_count, and this confuses the resume
sequence that checks the power_count as well.
Originally, this go-to-D3 sequence should be a simple task without the
power-up sequence. But, it'd need some proper sanity checks in the
case of power-saved state, so it's not too easy to write now in the
3.4-rc cycle.
In short, the safest option now is to revert this affecting commit.
Of course, we need to clean up and robustify the power-saving code
better for 3.5 kernel.
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some old codecs like ALC880 seem to give a bogus pin capability value 0
occasionally. This breaks the new sanity check in snd_hda_set_pin_ctl().
Skip the sanity checks in such a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function to guess the default VREF pin control bits
for mic in. This can be used to set the pin control value safely
matching with the actual pin capabilities.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For setting the pin-control values more safely to match with the
actual pin capability bits, a copule of new helper functions,
snd_hda_set_pin_ctl() and snd_hda_set_pin_ctl_cache(), are
introduced. These are simple replacement of the codec verb write with
AC_VERB_SET_PIN_WIDGET but do more sanity checks and filter out
superfluous pin-control bits if they don't fit with the corresponding
pin capabilities.
Some codecs are screwed up or ignore the command when such a wrong bit
is set. These helpers will avoid such secret errors.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since it's not always safe to assume that the vmaster hook is purely the
mute-LED control, add the flag indicating whether to expose the mute-LED
enum control or not. Currently, conexant codec sets this off for non-HP
laptops where EAPD may be used really as EAPD.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create snd_hda_add_vmaster_hook() and snd_hda_sync_vmaster_hook()
helper functions to handle the mute-LED in vmaster hook more
commonly. In the former function, a new enum control "Mute-LED Mode"
is added. This provides user to choose whether the mute-LED should be
turned on/off explicitly or to follow the master-mute status.
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver is changed to use vmaster or a new slave element is
added by the improvement of the parser code, user may face often the
silent output because of the muted slave mixer although Master volume
is properly set. And they complain. And I get upset.
Although such a mixer element should be initialized via "alsactl init",
it'd be more user-friendly if the known output slaves are unmuted and
set to 0dB so that user can control the volume only with Master as
default. Since Master is still set muted as default even with this
change, no risk of the speaker blow up, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've seen a problem with a pop-noise at suspend/resume on a HP
machine with ALC269, and it turned out to be an issue that the
controller going to D3 while the codec is unused.
When the device is once suspended and resumed and kept unused, the
driver doesn't initialize the codecs. Instead, the codec chips are
set up dynamically at the first usage. Now, suppose the device going
to suspend again before the codec is set up. The controller is turned
off to D3 while the codec chips are untouched. This caused a pop
noise because the codec chip might have been turned on implicitly by
the hardware.
As a workaround, the codec chip needs to be set to D3 when going to
suspend no matter whether it was used or not. Also, for making it
happening, the controller has to be always set up in the resume path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some codecs don't supply the mute amp-capabilities although the lowest
volume gives the mute. It'd be handy if the parser provides the mute
mixers in such a case.
This patch adds an extension amp-cap bit (which is used only in the
driver) to represent the min volume = mute state. Also modified the
amp cache code to support the fake mute feature when this bit is set
but the real mute bit is unset.
In addition, conexant cx5051 parser uses this new feature to implement
the missing mute controls.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42825
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In most cases, the slave strings for vmaster are identical between
volumes and switches except for "xxx Volume" and "xxx Switch" suffix.
Now snd_hda_add_vmaster() takes the optional suffix argument so that
each string can be composed with the given suffix, and we can share the
slave name strings in both volume and switch calls nicely.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This typo caused the wrong codec's nid to be checked for wcaps type.
As a result, sometimes speakers would duplicate the output sent to
HDMI output.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/924320
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the driver supports up to 10 streams. This is a restriction in
hda_intel.c and hda_codec.c: in the former, the fixed array size limits
the amount, and in the latter, the fixed device-number assignment table
(in get_empty_pcm_device()) limits the possibility.
This patch reduces the restriction by
- using linked list for managing PCM instances in hda_intel.c, and
- assigning non-fixed device numbers for the extra devices
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In snd_hda_check_board_codec_sid_config(), not only comparing with the
exact value but allow the bit-mask comparison for vendor-only, etc.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multiple headphone pins are usually handled as copied from the same
source, not as individual channels like front and surround. Thus it'd
be more correct to avoid the channel suffix for "Headphone" pin labels
in snd_hda_get_pin_label() but give an index number instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function now gives more unique names for the output pins by adding
some prefix and suffix for the location and the channels. Otherwise, it
can pass the index number.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a table containing the pins and their jack-detection states
for avoiding the unnecessary verbs to check the pin status at each time.
When the unsol event is enabled via snd_hda_jack_detect_enable(), it
automatically adds the given NID to the table. Then the driver supposes
that the codec driver will set the dirty flag appropariately when an
unsolicited event is invoked for that pin.
The behavior for reading other pins that aren't registered in the table
doesn't change. Only the pins assigned to the table are cached, so far.
In near futre, this table can be extended to use the central place for
the unsolicited events of all pins, etc, and eventually include the
jack-detect kcontrols that replace the current input-jack stuff.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create a new helper function snd_hda_get_pin_label() for getting a label
string for both input and output pins. hda_get_input_pin_label() is
obsoleted by this function, and the callers are replaced appropriately
now by this patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We disabled the check of NO_PRESENCE bit of the default pin-config
in commit f4419172 temporarily. One problem was that the first
implementation was wrong -- the bit after the shift must be checked.
However, this would still give many regressions on machines with broken
BIOS. They set this bit wrongly even on active pins.
A workaround is to check whether all pins contain this bit. As far as
I've checked, broken BIOSen set this bit on all pins, no matter whether
active or not. In such a case, the driver should ignore this bit check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a virtual mater control is created, the driver looks for slave
elements from the assigned card instance. But this may include the
elements of other codecs when multiple codecs are on the same HD-audio
bus. This works at the first time, but it'll give Oops when it's once
freed and re-created via reconfig sysfs.
This patch changes the element-look-up strategy to limit only to the
mixer elements of the same codec.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When 5.1 or more headphone or speaker pins are provided, the parser still
takes as is without fixing the order of channel mapping, which leads in
the unexpected strange channel order by surround outputs.
This patch fixes the issue by applying the same fix-up not only to
line_out_pins[] but also hp_pins[] and speaker_pins[].
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since hda_proc.c is now the only user of snd_print_pcm_rates(), better to
put it back locally to hda_proc.c and revert to the old style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SAD sampling rate information reported in
/proc/asound/cardX/eldX is incorrect due to a mismatch
between HDA and HDMI frequencies. Add new routine to provide
relevant values.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar to Line Out, these constants form the base for future
patches enabling input jack reporting for Line in jacks.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since really_cleanup_stream() is called from both purity_inactive_streams()
and hda_cleanup_all_streams(), the verbs to clear the PCM channel and
format may be called multiple times unnecessarily.
This patch adds checks to skip these unneeded verbs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recursive search of widget connections in snd_hda_get_conn_index()
must be terminated at the pin and the audio-out widgets. Otherwise
you'll get "too deep connection" warnings unnecessarily.
Reported-by: Francis Moreau <francis.moro@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For supporting both the multiple headphones and the multiple speakers,
add the new field in struct hda_multi_out, and evaluate in the standard
setup functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and add a new bit-flags argument to specify the behavior of the
function. The older function is kept as is (as a wrapper).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In snd_hda_parse_pin_def_config(), we checked the associated number
of speaker pins and accepts only one number exclusively. But many BIOS
seem to give different assoc number for surround speakers, thus we'd
better to accept all speaker pins no matter which assoc number, and sort
like done for the headphone pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>