Should be the same values as before, except:
GF117 has smaller buffer allocated, as per register setup.
GK20A now uses values from Tegra driver, not GK104's.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Removes need for fixed buffer indices, and allows the functions
utilising them to also be run outside of context generation.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Default ZBC table is compatible with binary driver defaults.
Userspace will need to be updated to take full advantage of this
feature, however, some applications will see a performance boost
without updated drivers.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
One of the next commits will remove some of the class IDs, leaving only
the ones used by NVIDIA which, presumably, mark where functionality
changes actually happened.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The indirect method has been left in-place here as a fallback path, as
it may not be possible to map the non-PAGE_SIZE aligned control areas
across some chipset+interface combinations.
This isn't a problem for the primary use-case where the core and drm
are linked together in kernel-land, but across a VM or (in the case
where it applies now) between the core in the kernel and a userspace
test tool.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is a wrapper around the interfaces defined in an earlier commit,
and is also used by various userspace (either by a libdrm backend, or
libpciaccess) tools/tests.
In the future this will be extended to handle channels, replacing some
long-unloved code we currently use, and allow fifo/display/mpeg (hi
Ilia ;)) engines to all be exposed in the same way.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This forms the basis for the new APIs that will be exposed to userspace,
giving it access to:
- Object method calls, the immediately useful of which is performance
counters and the abiity to manipulate the ZBC tables.
- Information on the child classes an object supports, in order to avoid
having to try all supported classes until successful.
- Notifications, which will be used in the future to inform the client
if its channel was killed due to a lockup, etc.
This commit imports the interfaces, but are not currently used. The DRM
portion of the driver will be ported to speak to the core using these
interfaces as much as possible.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is a lot of prep-work for being able to send event notifications
back to userspace. Events now contain data, rather than a "something
just happened" signal.
Handler data is now embedded into a containing structure, rather than
being kmalloc()'d, and can optionally have the notify routine handled
in a workqueue.
Various races between suspend/unload with display HPD/DP IRQ handlers
automagically solved as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Linux 3.16 fixed multiple bugs in kms pageflip completion events
and timestamping, which were originally introduced in Linux 3.13.
These fixes have been backported to all stable kernels since 3.13.
However, the userspace nouveau-ddx needs to be aware if it is
running on a kernel on which these bugs are fixed, or not.
Bump the patchlevel of the drm driver version to signal this,
so backporting this patch to stable 3.13+ kernels will give the
ddx the required info.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> #v3.13+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Vblank irqs don't get disabled during suspend or driver
unload, which causes irq delivery after "suspend" or
driver unload, at least until the gpu is powered off.
This could race with drm_vblank_cleanup() in the case
of nouveau and cause a use-after-free bug if the driver
is unloaded.
More annoyingly during everyday use, at least on nv50
display engine (likely also others), vblank irqs are
off after a resume from suspend, but the drm doesn't
know this, so all vblank related functionality is dead
after a resume. E.g., all windowed OpenGL clients will
hang at swapbuffers time, as well as many fullscreen
clients in many cases. This makes suspend/resume useless
if one wants to use any OpenGL apps after the resume.
In Linux 3.16, drm_vblank_on() was added, complementing
the older drm_vblank_off() to solve these problems
elegantly, so use those calls in nouveaus suspend/resume
code.
For kernels 3.8 - 3.15, we need to cherry-pick the
drm_vblank_on() patch to support this patch.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> #v3.16
Cc: <stable@vger.kernel.org> #v3.8+: f275228: drm: Add drm_vblank_on()
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Header for tegra_powergate functions has moved to soc/tegra/pmc.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add support for reclocking on GK20A, using a statically-defined pstates
table. The algorithms for calculating the coefficients and setting the
clocks are directly taken from the ChromeOS kernel.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Make nouveau_clock_create() take new two optional arguments: an array
of pstates and its size. When these are specified,
nouveau_clock_create() will use the provided pstates instead of
probing them using the BIOS.
This is useful for platforms which do not provide a BIOS, like Tegra.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allow the clock subsystem to operate even if voltage and thermal devices
are not set for the device (for people with watercooling! ;))
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This fixes a crash when we reload Nouveau DRM.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The DMA API is the recommended way to map pages no matter what the
underlying bus is. Use the DMA functions for page mapping and remove
currently existing wrappers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Detect and workaround the absence of a power device so chips that do not
feature one (e.g. GK20A) can still use this driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GK20A's BAR is functionally identical to NVC0's, but do not support
being ioremapped write-combined. Create a BAR instance for GK20A that
reflect that state.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Some BARs (like GK20A's) do not support being ioremapped write-combined.
Add a boolean property to the BAR structure and handle that case in the
Nouveau BO implementation.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Add a platform driver for Nouveau devices declared using the device tree
or platform data. This driver currently supports GK20A on Tegra
platforms and is only compiled for these platforms if Nouveau is
enabled.
Nouveau will probe the chip type itself using the BOOT0 register, so all
this driver really needs to do is to make sure the module is powered and
its clocks active before calling nouveau_drm_platform_probe().
Heavily based on work done by Thierry Reding.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
echo ac:id >> pstate # select mode when on mains power
echo dc:id >> pstate # select mode when on battery
echo id >> pstate # select mode for both
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As a side note.. It's a bit hard to figure out how to name this commit..
GK20A is NVEA, which is before NV108 (GK208).. Confusing.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As documented at:
ftp://download.nvidia.com/open-gpu-doc/gk104-disable-graphics-power-gating/1/gk104-disable-graphics-power-gating.txt
NVIDIA were not able document the steps necessary to detect whether this
is required or not at this time. However, they did confirm that this
procedure is safe to perform unconditionally on GK104/6. GK107 does not
have the power gating feature, and it was recommended that we do not
perform these steps there as the effects were not verified.
The disable path is from observing the binary driver, and not
documented in the link above.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pages allocated using the DMA API have a coherent memory mapping. Make
this mapping visible to drivers so they can decide to use it instead of
creating their own redundant one.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
* Much better HDMI infoframe support for OMAP
* Cirrus Logic CLPS711X framebuffer driver
* DT support for PL11x CLCD driver
* Various small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gXX+
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
Merge more incoming from Andrew Morton:
"Two new syscalls:
memfd_create in "shm: add memfd_create() syscall"
kexec_file_load in "kexec: implementation of new syscall kexec_file_load"
And:
- Most (all?) of the rest of MM
- Lots of the usual misc bits
- fs/autofs4
- drivers/rtc
- fs/nilfs
- procfs
- fork.c, exec.c
- more in lib/
- rapidio
- Janitorial work in filesystems: fs/ufs, fs/reiserfs, fs/adfs,
fs/cramfs, fs/romfs, fs/qnx6.
- initrd/initramfs work
- "file sealing" and the memfd_create() syscall, in tmpfs
- add pci_zalloc_consistent, use it in lots of places
- MAINTAINERS maintenance
- kexec feature work"
* emailed patches from Andrew Morton <akpm@linux-foundation.org: (193 commits)
MAINTAINERS: update nomadik patterns
MAINTAINERS: update usb/gadget patterns
MAINTAINERS: update DMA BUFFER SHARING patterns
kexec: verify the signature of signed PE bzImage
kexec: support kexec/kdump on EFI systems
kexec: support for kexec on panic using new system call
kexec-bzImage64: support for loading bzImage using 64bit entry
kexec: load and relocate purgatory at kernel load time
purgatory: core purgatory functionality
purgatory/sha256: provide implementation of sha256 in purgaotory context
kexec: implementation of new syscall kexec_file_load
kexec: new syscall kexec_file_load() declaration
kexec: make kexec_segment user buffer pointer a union
resource: provide new functions to walk through resources
kexec: use common function for kimage_normal_alloc() and kimage_crash_alloc()
kexec: move segment verification code in a separate function
kexec: rename unusebale_pages to unusable_pages
kernel: build bin2c based on config option CONFIG_BUILD_BIN2C
bin2c: move bin2c in scripts/basic
shm: wait for pins to be released when sealing
...
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit b6d547791f.
The panel self refresh clearly isn't stable yet, and causes my laptop
(Haswell ULT in a Sony Vaio Pro) to have the screen lock up. Maybe it
doesn't ever get out of self-refresh, or maybe there are gremlins in the
machine that get unhappy. Regardless, it's broken, and it gets
reverted.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull intel drm fixes from Daniel Vetter:
"So I heard that proper pull requests have a revert on top ;-) So here
we go with my usual mid-merge-window pile of fixes.
[ Ed. This revert thing had better not become the "in" thing ]
Big fix is the duct-tape for ring init on g4x platforms, we seem to
have found the magic again to make those machines as happy as before
(not perfect though unfortunately, but that was never the case).
Otherwise fixes all over:
- tune down some overzealous debug output
- VDD power sequencing fix after resume
- bunch of dsi fixes for baytrail among them hw state checker
de-noising
- bunch of error state capture fixes for bdw
- misc tiny fixes/workarounds for various platforms
Last minute rebase was to kick out two patches that shouldn't have
been in here - they're for the state checker, so 0 functional code
affected.
Jani's back from vacation, so he'll take over -fixes from here"
* tag 'drm-intel-fixes-2014-08-08' of git://anongit.freedesktop.org/drm-intel: (21 commits)
Revert "drm/i915: Enable semaphores on BDW"
drm/i915: read HEAD register back in init_ring_common() to enforce ordering
drm/i915: Fix crash when failing to parse MIPI VBT
drm/i915: Bring GPU Freq to min while suspending.
drm/i915: Fix DEIER and GTIER collecting for BDW.
drm/i915: Don't accumulate hangcheck score on forward progress
drm/i915: Add the WaCsStallBeforeStateCacheInvalidate:bdw workaround.
drm/i915: Refactor Broadwell PIPE_CONTROL emission into a helper.
drm/i915: Fix threshold for choosing 32 vs. 64 precisions for VLV DDL values
drm/i915: Fix drain latency precision multipler for VLV
drm/i915: Collect gtier properly on HSW.
drm/i915: Tune down MCH_SSKPD values warning
drm/i915: Tune done rc6 enabling output
drm/i915: Don't require dev->struct_mutex in psr_match_conditions
drm/i915: Fix error state collecting
drm/i915: fix VDD state tracking after system resume
drm/i915: Add correct hw/sw config check for DSI encoder
drm/i915: factor out intel_edp_panel_vdd_sanitize
drm/i915: wait for all DSI FIFOs to be empty
drm/i915: work around warning in i915_gem_gtt
...
This reverts commit 521e62e49a.
Although POST_SYNC brought a bit of stability to Semaphores on BDW
it didn't solved all issues and some hungs can still occour when
semaphores are enabled on BDW. Also some sloweness can be found on some
igt tests, althoguth it apparently doesn't affect real workloads.
Besides that, no real performance gain was found on our tests with different
and even multiple workloads.
Let's disable it again for now. At least until we are sure it is safe
to re-enable it.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Withtout this, ring initialization fails reliabily during resume with
[drm:init_ring_common] *ERROR* render ring initialization failed ctl 0001f001 head ffffff8804 tail 00000000 start 000e4000
This is not a complete fix, but it is verified to make the ring
initialization failures during resume much less likely.
We were not able to root-cause this bug (likely HW-specific to Gen4 chips)
yet. This is therefore used as a ducttape before problem is fully
understood and proper fix created, so that people don't suffer from
completely unusable systems in the meantime.
The discussion and debugging is happening at
https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This particular nasty presented itself while trying to register the
intelfb device (intel_fbdev.c). During the process of registering the device
the driver will disable the crtc via i9xx_crtc_disable. These will
also disable the panel using the generic mipi panel functions in
dsi_mod_vbt_generic.c. The stale MIPI generic data sequence pointers would
cause a crash within those functions. However, all of this is happening
while console_lock is held from do_register_framebuffer inside fbcon.c. Which
means that you got kernel log and just the device appearing to reboot/hang for
no apparent reason.
The fault started from the FB_EVENT_FB_REGISTERED event using the
fb_notifier_call_chain call in fbcon.c.
This regression has been introduced in
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Add regression citation.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
This reverts commit 48ba813701.
Thanks to Chris:
"drm_file->is_master is not synomous with having drm_file->master ==
drm_file->minor->master. This is because drm_file->master is the same
for all drm_files of the same generation and so when there is a master,
every drm_file believes itself to be the master. Confusion ensues and
things go pear shaped when one file is closed and there is no master
anymore."
Conflicts:
drivers/gpu/drm/drm_drv.c
drivers/gpu/drm/drm_stub.c
We might be leaving the PGU Frequency (and thus vnn) high during the suspend.
Flusing the delayed work queue should take care of this.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW has many other Display Engine interrupts and GT interrupts registers.
Collecting it properly on gpu_error_state.
On debugfs all was properly listed already but besides we were also listing old
DEIER and GTIER that doesn't exist on BDW anymore. This was causing
unclaimed register messages
v2: Fix small issues of first version and don't read DEIER regs when pipe's
power well is disabled
v3: bikeshed accepted: use enum pipe pipe instead of int i for pipe interection
v4: Ben notice previous version was checking for display_power_enabled without
using propper locks. Using _unlocked version isn't reliable and we cannot
get this registers when power well is off. So let's avoid getting all DE_IER
per pipe for now. If someone think this is an useful information it can be
added later.
v5: Ben: put back debugfs stuff that might be coverred by pm_get and use
gen >= 8 trying to predict future.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81701
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: (v3) Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the actual head has progressed forward inside a batch (request),
don't accumulate hangcheck score.
As the hangcheck score in increased only by acthd jumping backwards,
the result is that we only declare an active batch as stuck if it is
trapped inside a loop. Or that the looping will dominate the batch
progression so that it overcomes the bonus that forward progress gives.
v2: Improved commit message (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: s/active_loop/active (loop)/ as requested by Chris.]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Broadwell, any PIPE_CONTROL with the "State Cache Invalidate" bit set
must be preceded by a PIPE_CONTROL with the "CS Stall" bit set.
Documented on the BSpec 3D workarounds page.
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[vsyrjala: add chv w/a note too]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll want to reuse this for a workaround.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rmove now unused int.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qYgE
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.17-rc1
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
* tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: add MODULE_DEVICE_TABLEs
drm/tegra: dc - Reset controller on driver remove
drm/tegra: Properly align stride for framebuffers
drm/tegra: sor - Configure proper sync polarities
drm/tegra: sor - Use bits-per-color from panel
drm/tegra: Make job submission 64-bit safe
drm/tegra: Allow non-authenticated processes to create buffer objects
drm/tegra: Add SET/GET_FLAGS IOCTLs
drm/tegra: Add SET/GET_TILING IOCTLs
drm/tegra: Implement more tiling modes
drm/tegra: dsi - Handle non-continuous clock flag
drm/tegra: sor - missing unlock on error
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vf7m
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v3.17-rc1
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
* tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux: (30 commits)
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
drm/panel: simple: Add Innolux N116BGE panel support
...
The DDL registers can hold 7bit numbers. Make the most of those seven
bits by adjusting the threshold where we switch between the 64 vs. 32
precision multipliers.
Also we compute 'entries' to make the decision about precision, and then
we recompute the same value to calculate the actual drain latency. Just
use the already calculate 'entries' there.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GTIER and DEIER doesn't have same interface on HSW so this "or" operation
makes the information provided useless.
v2: since we have gtier variable already let's split for everybody
and avoid the strange | op.
Also avoid overriding the value that was set for vlv. In this case I
believe that we should reorganize the whole function, but I'll respect
the comment that ask to not touch the order and let this organization
work to be done later.
v3: moving VLV check to the right place.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Users often can't do anything about this since their vendors stopped
providing BIOS updates. Also we seem to be able to hack around it
with increased latency values, and thus far the only reports have
been for screens with really high resolutions. So tune it down to a
level where only developers can see it.
Also drop some of the end-user fluff.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power users spot this and then get adventurous and try to adjust
module driver options. Nothing good ever came out of that, so
hide it better.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I've reworked psr support to no longer require x-tiling we don't
check any state protected by the Giant GEM Lock. So drop that check.
Also boo for lockdep_assert_held for not yelling when lockdep is
disabled.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix signal_offset when recording semaphore state on BDW.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like during booting the BIOS can leave the VDD bit enabled after
system resume. So apply the same state sanitization there too. This
fixes a problem where after resume the port power domain refcount gets
unbalanced.
v2:
- unchanged
v3:
- call edp sanitizing from the encoder reset handler (Daniel)
Reported-and-tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.
Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly
v2: Address review comments by Daniel
- Check if DPLL is enabled rather than checking pipe output type
- set adjusted_mode->flags to 0 in compute_config rather than using
pipe_config->quirks
- Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
- updated dpll_hw_state correctly
- Updated commit message and title
v3: Address review comments by Imre
- Proper masking of P1, M1 fields while computing divisors
- assert in case of bpp mismatch
- guard for divide by 0 while computing pclk
- Use ARRAY_SIZE instead of direct calculation
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by an upcoming patch too that needs to sanitize the
VDD state during resume. The additional async disabling is only needed
for the resume path, here it doesn't make a difference since we enable
VDD right after the sanitize call.
v2:
- don't set intel_dp ptr for non-eDP encoders (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ensure that the DSI packets for a particular sequence are completely
sent before going ahead in the enabling or disabling of the panel
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gcc warns that addr might be used uninitialized. It may not, but I see
why gcc gets confused.
Additionally, hiding code with side-effects inside WARN_ON() argument
seems uncool, so I moved it outside.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[danvet: Add obligatory /* shuts up gcc */ comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new devm_gpiod_get_optional() to simplify the probe code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add drm_panel controls to support powerup/down of the
eDP panel, if one is present at the sink side.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add commit callback for exynos_dp, and move the DP link training,
video configuration code from the hotplug handler into commit().
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B133HTN01 is a 13.6" FHD TFT LCD panel connecting to an eDP
interface and with an integrated LED backlight unit.
This panel is used on the Samsung Chromebook 2 (XE503C32).
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For most of the panels, we need to provide delays during various stages
of panel power up and power down. Add a structure to hold those delay
values and use them in corresponding functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move out code from enable and disable routines to prepare
and unprepare routines, so that functionality is properly
distributed across all the panel functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move out code from enable and disable routines to prepare
and unprepare routines, so that functionality is properly
distributed across all the panel functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move out code from enable and disable routines to prepare
and unprepare routines, so that functionality is properly
distributed across all the panel functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify tegra output driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify exynos_dsi driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify exynos_dpi driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
simple-panel is not a valid panel model, so there is no data (video
timings, etc.) associated with it. Therefore drivers can't do anything
useful with it, so it should not appear in the table of OF matches.
Device trees will always need to specify the exact model of the panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Innolux N116BGE is an 11.6" WXGA TFT LCD panel connecting to an eDP
interface and with an integrated LED backlight unit.
It is used in the Tegra132 Norrin reference design.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Everyone agrees we should do this,
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
bunch of cleanups
* 'drm-next' of git://people.freedesktop.org/~dvdhrm/linux:
drm: mark drm_context support as legacy
drm: make sysfs device always available for minors
drm: make minor->index available early
drm: merge drm_drv.c into drm_ioctl.c
drm: move module initialization to drm_stub.c
drm: don't de-authenticate clients on master-close
drm: drop redundant drm_file->is_master
drm: extract legacy ctxbitmap flushing
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
We need to take the connection mutex around the link status
check for non-MST case, but also around the MST link training
on short HPDs.
I suspect we actually should have a dpcd lock in the future as
well, that just lock the local copies of dpcd and flags stored
from that.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Additional Hawaii fixes
- Support for using the display scaler on non-fixed mode displays
- Support for new firmware format that makes it easier to update
- Enable dpm by default on additional asics
- GPUVM improvements
- Support for uncached and write combined gtt buffers
- Allow allocation of BOs larger than visible vram
- Various other small fixes and improvements
* 'drm-next-3.17' of git://people.freedesktop.org/~agd5f/linux: (57 commits)
drm/radeon: Prevent hdmi deep color if max_tmds_clock is undefined.
drm/radeon: Use pflip irqs for pageflip completion if possible. (v2)
drm/radeon: tweak ACCEL_WORKING2 query for the new firmware for hawaii
drm/radeon: use packet3 for nop on hawaii with new firmware
drm/radeon: tweak ACCEL_WORKING2 query for hawaii
drm/radeon: use packet2 for nop on hawaii with old firmware
drm/radeon: update IB size estimation for VM
drm/radeon: split PT setup in more functions
drm/radeon: add VM GART copy optimization to NI as well
drm/radeon: take a BO reference on VM cleanup
drm/radeon: add radeon_bo_ref function
drm/radeon: remove taking mclk_lock from radeon_bo_unref
drm/radeon: adjust default radeon_vm_block_size v2
drm/radeon: try to enable VM flushing once more
drm/radeon: use an intervall tree to manage the VMA v2
drm/radeon: remove radeon_bo_clear_va
drm/radeon: invalidate moved BOs in the VM (v2)
drm/radeon: re-enable dpm by default on BTC
drm/radeon: re-enable dpm by default on cayman
drm/radeon: Only flush HDP cache from idle ioctl if BO is in VRAM
...
This renames all drm-context helpers to drm_legacy_*() and moves the
internal definitions into the new drm_legacy.h header. This header is
local to DRM-core and drivers shouldn't access it.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
HDMI spec requires a valid max_tmds_clock from edid for hdmi
deep color modes. If a sink violates this, disable deep color.
Also add a hint to user about the deep_color module parameter if
deep color is disabled due to that.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For each minor we allocate a sysfs device as minor->kdev. Currently, this
is allocated and registered in drm_minor_register(). This makes it
impossible to add sysfs-attributes to the device before it is registered.
Therefore, they are not added atomically, nor can we move device_add()
*after* ->load() is called.
This patch makes minor->kdev available early, but only adds the device
during minor-registration. Note that the registration is still called
before ->load() as debugfs needs to be split, too. This will be fixed in
follow-ups.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Instead of allocating the minor-index during registration, we now do this
during allocation. This way, debug-messages between minor-allocation and
minor-registration will now use the correct minor instead of 0. Same is
done for unregistration vs. free, so debug-messages between
device-shutdown and device-destruction show proper indices.
Even though minor-indices are allocated early, we don't enable minor
lookup early. Instead, we keep the entry set to NULL and replace it during
registration / unregistration. This way, the index is allocated but lookup
only works if registered.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
All that is left in drm_drv.c is ioctl management. Merge it into
drm_ioctl.c so we have all ioctl management in one file (and the name is
much more fitting).
Maybe we should now rename drm_stub.c to drm_drv.c again?
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Most of the new DRM management functions are nowadays in drm_stub.c. By
moving the core module initialization to drm_stub.c we can make several
global variables static and keep the stub-open helper local.
The core files now look like this:
drm_stub.c: Core management
drm_drv.c: Ioctl dispatcher
drm_ioctl.c: Actual ioctl backends
drm_fops.c: Char-dev file-operations
A follow-up patch will move what is left from drm_drv.c into drm_ioctl.c.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
If an active DRM-Master closes its device, we deauthenticate all clients
on that master. However, if an inactive DRM-Master closes its device, we
do nothing. This is quite inconsistent and breaks several scenarios:
1) If this was used as security mechanism, it fails horribly if a master
closes a device while VT switched away. Furthermore, none of the few
drivers using ->master_*() callbacks seems to require it, anyway.
2) If you spawn weston (or any other non-UMS compositor) in background
while another compositor is active, both will get assigned to the
same "drm_master" object. If the foreground compositor now exits, all
clients of both the foreground AND background compositor will be
de-authenticated leading to unexpected behavior.
Stop this non-sense and keep clients authenticated. We don't do this when
dropping DRM-Master (i.e., switching VTs) so don't do it on active-close
either!
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
The drm_file->is_master field is redundant as it's equivalent to:
drm_file->master && drm_file->master == drm_file->minor->master
1) "=>"
Whenever we set drm_file->is_master, we also set:
drm_file->minor->master = drm_file->master;
Whenever we clear drm_file->is_master, we also call:
drm_master_put(&drm_file->minor->master);
which implicitly clears it to NULL.
2) "<="
minor->master cannot be set if it is non-NULL. Therefore, it stays as
is unless a file drops it.
If minor->master is NULL, it is only set by places that also adjust
drm_file->is_master.
Therefore, we can safely drop is_master and replace it by an inline helper
that matches:
drm_file->master && drm_file->master == drm_file->minor->master
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
The ctxbitmap code is only used by legacy drivers so lets try to keep it
as separated as possible. Furthermore, the locking is non-obvious and
kinda weird with ctxlist_mutex *and* struct_mutex. Keeping all ctxbitmap
access in one file is much easier to review and makes drm_release() more
readable.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Skip the "manual" pageflip completion checks via polling and
guessing in the vblank handler radeon_crtc_handle_vblank() on
asics which are known to reliably support hw pageflip completion
irqs. Those pflip irqs are a more reliable and race-free method
of handling pageflip completion detection, whereas the "classic"
polling method has some small races in combination with dpm on,
and with the reworked pageflip implementation since Linux 3.16.
On old asics without pflip irqs, the classic method is used.
On asics with known good pflip irqs, only pflip irqs are used
by default, but a new module parameter "use_pflipirqs" allows to
override this in case we encounter asics in the wild with
unreliable or faulty pflip irqs. A module parameter of 0 allows
to use the classic method only in such a case. A parameter of 1
allows to use both classic method and pflip irqs as additional
band-aid to avoid some small races which could happen with the
classic method alone. The setting 1 gives Linux 3.16 behaviour.
Hw pflip irqs are available since R600.
Tested on DCE-4, AMD Cedar - FirePro 2270.
v2: agd5f: only enable pflip interrupts on DCE4+ as they are not
reliable on older asics.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the previous tweak for hawaii to return 3 if the new firmware is used.
Signed-off-by: Andreas Boll <andreas.boll.dev@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Older firmware didn't support the new nop packet.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Andreas Boll <andreas.boll.dev@gmail.com>
Return 2 so we can be sure the kernel has the necessary
changes for acceleration to work.
Note: This patch depends on these two commits:
- drm/radeon: fix cut and paste issue for hawaii.
- drm/radeon: use packet2 for nop on hawaii with old firmware
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Andreas Boll <andreas.boll.dev@gmail.com>
Cc: stable@vger.kernel.org
Older firmware didn't support the new nop packet.
v2 (Andreas Boll):
- Drop usage of packet3 for new firmware
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Andreas Boll <andreas.boll.dev@gmail.com>
Cc: stable@vger.kernel.org
That should allow us to allocate bigger BOs.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the decision what to use into the common VM code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ben Skeggs