Instead of open-coding the accesses and length check do
the length check in the IE parser and assign a struct
pointer for use in the remaining code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the sake of speed of calculation and number accuracy,
mac80211 tracks the RSSI in dBm * 16. But it forgot to
divide back by 16 when the RSSI is asked by the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since now we disconnect before suspend, various code which save
connection state can now be removed from suspend and resume
procedure. Cleanup on resume side is smaller as ieee80211_reconfig()
is also used for H/W restart.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In beacons and association response frames an AP may include an
operating mode notification element to advertise changes in the
number of spatial streams it can receive. Handle this using the
existing function that handles the action frame, but only handle
NSS changes, not bandwidth changes which aren't allowed here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no use for it, WPA is entirely handled in
wpa_supplicant in userspace, so don't pick the IE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending authentication/association frames they
might take a bit of time to go out because we may
have to synchronise with the AP, in particular in
the case where it's really a P2P GO. In this case
the 200ms fixed timeout could potentially be too
short if the beacon interval is relatively large.
For drivers that report TX status we can do better.
Instead of starting the timeout directly, start it
only when the frame status arrives. Since then the
frame was out on the air, we can wait shorter (the
typical response time is supposed to be 30ms, wait
100ms.) Also, if the frame failed to be transmitted
try again right away instead of waiting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when the driver requires the DTIM period,
mac80211 will wait to hear a beacon before association.
This behavior is suboptimal since some drivers may be
able to deal with knowing the DTIM period after the
association, if they get it at all.
To address this, notify the drivers with bss_info_changed
with the new BSS_CHANGED_DTIM_PERIOD flag when the DTIM
becomes known. This might be when changing to associated,
or later when the entire association was done with only
probe response information.
Rename the hardware flag for the current behaviour to
IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC to more accurately
reflect its behaviour. IEEE80211_HW_NEED_DTIM_PERIOD is
no longer accurate as all drivers get the DTIM period
now, just not before association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.
In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit 529ba6e931
("mac80211: clean up association better in suspend")
introduced a bug when resuming from WoWLAN when a
device reset is desired. This case must not use the
suspend_bss_conf as it hasn't been stored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The initiator/tx doesn't really identify why an
aggregation session is stopped, give a reason
for stopping that more clearly identifies what's
going on. This will help tell the driver clearly
what is expected of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For AP/IBSS/mesh interfaces, call the driver to reconfigure
bss_info_changed only if the interface was beaconing before
suspend, otherwise we call the driver and it might interpret
the change as going from enabled to disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When suspending, bss_info_changed() is called to
disable beacons, but managed mode interfaces are
simply removed (bss_info_changed() is called with
"no change" only). This can lead to problems.
To fix this and copy the BSS configuration, clear
it during suspend and restore it on resume.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assuming 200 bytes are always enough for
all the IEs we add, give the length of the buffer
to the function and warn instead of overrunning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the low-level driver wants to support P2P GO
powersave configuration, it must set the cfg80211
flags and mac80211 will pass the parameters to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sujith reported warnings with suspend/resume due to
channel contexts. When I looked into it, I realised
that the code was completely broken as it unassigned
the channel contexts when suspending, which actually
means they are destroyed.
Eliad Peller then pointed out that we also need to
remove the channel contexts from the driver. When I
looked into this, I also noticed that the code isn't
handling the virtual monitor interface correctly (if
it exists.)
Fix this by calling just the driver methods (if they
are implemented) instead of using the channel context
management code. Also add reconfiguration for the
virtual monitor interface.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During testing our mac80211 driver a fatal error occurred which was
signalled to mac80211. Upon performing the reconfiguration of the
device a WARN_ON was triggered. This warning checked the return value
of drv_add_chanctx(). However, this returns -EOPNOTSUPP when the
driver does not provide the callback. As the callback is optional
better check it is defined before calling drv_add_chanctx().
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since channel contexts are usually present before
stations can be added to an interface, reassign
before stations them in reconfiguration as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On resume or firmware recovery, mac80211 sends a null
data packet to see if the AP is still around and hasn't
disconnected us. However, it always does this even if
it wasn't even connected before, leading to a warning
in the new channel context code. Fix this by checking
that it's associated.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For a local variable there's no need to use the atomic
set_bit() operation, use __set_bit() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of the current whitelist which accepts duplicates
only for the quiet and vendor IEs, use a blacklist of all
IEs (that we currently parse) that can't be duplicated.
This avoids detecting a beacon as corrupt in the future
when new IEs are added that can be duplicated.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save the AP's VHT capabilities (in managed
mode) and make them available to the driver
in the station information.
Unlike HT capabilities, they aren't restricted
to the common capabilities, so drivers must be
aware of their own capabilities.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
[fix endian conversion bug ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>