The celleb code has seen no actual development for ~7 years.
We (maintainers) have no access to test hardware, and it is highly
likely the code has bit-rotted.
As far as we're aware the hardware was never widely available, and is
certainly no longer available, and no one on the list has shown any
interest in it over the years.
So remove it. If anyone has one and cares please speak up.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Hai-Ying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
[Emil Medve: Sync with the upstream binding]
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Probably we should have not upstreamed this in the first place
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
We use r6 and r7 for epapr boot, but the current pre-C init will clobber
both of these.
This change does a simple replacement, of r6 -> r12 and r7 -> r13, so
that we hit platform init with these registers intact.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, a 64-bit little-endian zImage.epapr won't boot in epapr mode,
as we never return from platform_init.
Before entering C, we initialise our stack by setting r1 16 bytes below
the end of the _bss_stack:
stwu r0,-16(r1) /* establish a stack frame */
However, the called function will save the caller's lr in the caller's
frame's lr save area, at -16(r1) to -32(r1).
This means that writes to the fdt variable will corrupt the saved link
register:
0000000020c06018 l O .bss 0000000000001000 _bss_stack
0000000020c07018 l O .bss 0000000000000008 fdt
We'll need at least 32 bytes in the initial stack frame, to handle the
LR save area. We bump this to 112 bytes, as that'll be the max required
by ABIv1.
Thanks to Alistair Popple for debugging help.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We'll likely be entering the zImage.epapr as BE, so include the pseries
implementation of _zimage_start, which adds the endian fixup magic.
Although the endian fixup won't work on Book III-E machines starting LE,
the current entry point doesn't support LE anyway, so we shouldn't be
breaking anything.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For epapr-style boot, we may be little-endian. This change implements
the proper conversion for fdt*_to_cpu and cpu_to_fdt*. We also need the
full cpu_to_* and *_to_cpu macros for this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that the wrapper supports 64-bit builds, we see warnings when
attempting to cast pointers to int. Use unsigned long instead.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Drop planetcore_set_serial_speed() which had no users since its
inception in commit fec6047047 ("[POWERPC] bootwrapper: Add PlanetCore
firmware support") in 2007.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The $(image-n) variable will never exist, because unset Kconfig options
are '' and not 'n'.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the GPIO address in the device tree to match the documented location.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Change-Id: I16e63db731e55a3d60d4e147573c1af8718082d3
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Hai-Ying Wang <Haiying.Wang@freescale.com>
[Emil Medve: Sync with the upstream binding]
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Hai-Ying Wang <Haiying.Wang@freescale.com>
[Emil Medve: Sync with the upstream binding]
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for the Artesyn MVME2500 Single Board Computer.
The MVME2500 is a 6U form factor VME64 computer with:
- A single Freescale QorIQ P2010 CPU
- 1 GB of DDR3 onboard memory
- Three Gigabit Ethernets
- Five 16550 compatible UARTS
- One USB 2.0 port, one SHDC socket and one SATA connector
- One PCI/PCI eXpress Mezzanine Card (PMC/XMC) Slot
- MultiProcessor Interrupt Controller (MPIC)
- A DS1375T Real Time Clock (RTC) and 512 KB of Non-Volatile Memory
- Two 64 KB EEPROMs
- U-Boot in 16 SPI Flash
This patch is based on linux-3.18 and has been boot tested.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit 746c9e9f92 "of/base: Fix PowerPC address parsing hack" limited
the applicability of the workaround whereby a missing ranges is treated
as an empty ranges. This workaround was hiding a bug in the etsec2
device tree nodes, which have children with reg, but did not have
ranges.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Alexander Graf <agraf@suse.de>
Probably we should have not upstreamed this in the first place
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott says:
"Highlights include a bunch of 8xx optimizations, device tree bindings
for Freescale BMan, QMan, and FMan datapath components, misc device tree
updates, and inbound rio window support."
On some platforms a 5 second timeout during boot might be quite long, so
make it configurable. Run the loop at least once to let the user stop
the boot by holding a key pressed. If the timeout is set to 0, don't
wait for input, which can be used as a workaround if the boot hangs on
random data coming in on the serial port.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
[mpe: Changelog wording & whitespace]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Change-Id: If76cd705a01813abe53396c1486bc13c4289ee92
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Change-Id: I25ce24a25862b4ca460164159867abefe00ccdd1
Signed-off-by: Scott Wood <scottwood@freescale.com>
* Run "mtdparts default" on u-boot to create dynamic partitions
* Or use dynamic mtd partition with the help of bootargs in u-boot
Append bootargs with:
"mtdparts=ff800000.flash:1m(nand_uboot),512K(nand_dtb),8m(nand_kernel),-(fs);\
spiff707000.0:1m(spi_uboot),4m(spi_kernel),512k(spi_dtb),-(fs)'"
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull powerpc updates from Michael Ellerman:
"Here's a first pull request for powerpc updates for 3.18.
The bulk of the additions are for the "cxl" driver, for IBM's Coherent
Accelerator Processor Interface (CAPI). Most of it's in drivers/misc,
which Greg & Arnd maintain, Greg said he was happy for us to take it
through our tree.
There's the usual minor cleanups and fixes, including a bit of noise
in drivers from some of those. A bunch of updates to our EEH code,
which has been getting more testing. Several nice speedups from
Anton, including 20% in clear_page().
And a bunch of updates for freescale from Scott"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (130 commits)
cxl: Fix afu_read() not doing finish_wait() on signal or non-blocking
cxl: Add documentation for userspace APIs
cxl: Add driver to Kbuild and Makefiles
cxl: Add userspace header file
cxl: Driver code for powernv PCIe based cards for userspace access
cxl: Add base builtin support
powerpc/mm: Add hooks for cxl
powerpc/opal: Add PHB to cxl mode call
powerpc/mm: Add new hash_page_mm()
powerpc/powerpc: Add new PCIe functions for allocating cxl interrupts
cxl: Add new header for call backs and structs
powerpc/powernv: Split out set MSI IRQ chip code
powerpc/mm: Export mmu_kernel_ssize and mmu_linear_psize
powerpc/msi: Improve IRQ bitmap allocator
powerpc/cell: Make spu_flush_all_slbs() generic
powerpc/cell: Move data segment faulting code out of cell platform
powerpc/cell: Move spu_handle_mm_fault() out of cell platform
powerpc/pseries: Use new defines when calling H_SET_MODE
powerpc: Update contact info in Documentation files
powerpc/perf/hv-24x7: Simplify catalog_read()
...
Freescale updates from Scott (27 commits):
"Highlights include DMA32 zone support (SATA, USB, etc now works on 64-bit
FSL kernels), MSI changes, 8xx optimizations and cleanup, t104x board
support, and PrPMC PCI enumeration."
in commit 29f1aff2c (powerpc: Copy bootable images in the default
install script) we changed to copying all the built boot targets based
on the assumption that it's backwards compatible. It turns out that
debian devived installkernel scripts will barf if not given exactly 4
args.
This change reverts make install to just install the vmlinux (we can
change the dfault in a seperate patch) and introduces a new make
zInstall which works with a more flexible installkernel script.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change USB controller version to 2.5 in compatible string for T2080/T2081
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality only
T1042RDB_PI board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SATA 2.0
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1042RDB_PI board:
-add device tree
-Add entry in corenet_generic.c, as it is similar to other corenet platforms
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1040/T1042RDB is Freescale Reference Design Board.
The board can support both T1040/T1042 QorIQ Power Architecture™ processor.
T1040/T1042RDB board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SGMII
- QSGMII
- SATA 2.0
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Devices connected: EEPROM, thermal monitor, VID controller
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1040/T1042 RDB board:
-add device tree
-add entry in Kconfig to build
-Add entry in corenet_generic.c, as it is similar to other corenet platforms
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Change USB controller version to 2.5 in compatible string for T4240
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are some more powerpc bits for 3.17, essentially fixes.
The biggest series, also aimed at -stable, is from Aneesh and is the
result of weeks and weeks of debugging to find out why the heck or THP
implementation was occasionally triggering multi-hit errors in our
level 1 TLB. It ended up being a combination of issues including
subtleties as to how we should invalidate those special 'MPSS' pages
we use to allow the use of 16M pages inside 4K/64K "base page size"
segments (you really have to love our MMU !)
Another interesting one in the "OMG" category is the series from
Michael adding memory barriers to spin_is_locked(). That's also the
result of many days of debugging to figure out why the semaphore code
would occasionally crash in ways that made no sense. It ended up
being some creative lock stacking that was defeated by the fact that
our locks allow a load inside the locked section to be re-ordered with
the load of the lock value itself (I'm still of two mind about whether
to kill that once and for all by putting a heavier barrier back into
our lock implementation...). The fixes come with a long explanation
in the cset comments, feel free to read it if you feel like having a
headache today"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc/thp: Add tracepoints to track hugepage invalidate
powerpc/mm: Use read barrier when creating real_pte
powerpc/thp: Use ACCESS_ONCE when loading pmdp
powerpc/thp: Invalidate with vpn in loop
powerpc/thp: Handle combo pages in invalidate
powerpc/thp: Invalidate old 64K based hash page mapping before insert of 4k pte
powerpc/thp: Don't recompute vsid and ssize in loop on invalidate
powerpc/thp: Add write barrier after updating the valid bit
powerpc: reorder per-cpu NUMA information's initialization
powerpc/perf/hv-24x7: Use kmem_cache_free
powerpc/pseries/hvcserver: Fix endian issue in hvcs_get_partner_info
powerpc: Hard disable interrupts in xmon
powerpc: remove duplicate definition of TEXASR_FS
powerpc/pseries: Avoid deadlock on removing ddw
powerpc/pseries: Failure on removing device node
powerpc/boot: Use correct zlib types for comparison
powerpc/powernv: Interface to register/unregister opal dump region
printk: Add function to return log buffer address and size
powerpc: Add POWER8 features to CPU_FTRS_POSSIBLE/ALWAYS
powerpc/ppc476: Disable BTAC
...
Avoids this warning:
arch/powerpc/boot/gunzip_util.c:118:9: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull slave-dma updates from Vinod Koul:
"Some notable changes are:
- new driver for AMBA AXI NBPF by Guennadi
- new driver for sun6i controller by Maxime
- pl330 drivers fixes from Lar's
- sh-dma updates and fixes from Laurent, Geert and Kuninori
- Documentation updates from Geert
- drivers fixes and updates spread over dw, edma, freescale, mpc512x
etc.."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (72 commits)
dmaengine: sun6i: depends on RESET_CONTROLLER
dma: at_hdmac: fix invalid remaining bytes detection
dmaengine: nbpfaxi: don't build this driver where it cannot be used
dmaengine: nbpf_error_get_channel() can be static
dma: pl08x: Use correct specifier for size_t values
dmaengine: Remove the context argument to the prep_dma_cyclic operation
dmaengine: nbpfaxi: convert to tasklet
dmaengine: nbpfaxi: fix a theoretical race
dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores
dmaengine: add device tree binding documentation for the nbpfaxi driver
dmaengine: edma: Do not register second device when booted with DT
dmaengine: edma: Do not change the error code returned from edma_alloc_slot
dmaengine: rcar-dmac: Add device tree bindings documentation
dmaengine: shdma: Allocate cyclic sg list dynamically
dmaengine: shdma: Make channel filter ignore unrelated devices
dmaengine: sh: Rework Kconfig and Makefile
dmaengine: sun6i: Fix memory leaks
dmaengine: sun6i: Free the interrupt before killing the tasklet
dmaengine: sun6i: Remove switch statement from buswidth convertion routine
dmaengine: of: kconfig: select DMA_ENGINE when DMA_OF is selected
...
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc new goodies for 3.17. The short story:
The biggest bit is Michael removing all of pre-POWER4 processor
support from the 64-bit kernel. POWER3 and rs64. This gets rid of a
ton of old cruft that has been bitrotting in a long while. It was
broken for quite a few versions already and nobody noticed. Nobody
uses those machines anymore. While at it, he cleaned up a bunch of
old dusty cabinets, getting rid of a skeletton or two.
Then, we have some base VFIO support for KVM, which allows assigning
of PCI devices to KVM guests, support for large 64-bit BARs on
"powernv" platforms, support for HMI (Hardware Management Interrupts)
on those same platforms, some sparse-vmemmap improvements (for memory
hotplug),
There is the usual batch of Freescale embedded updates (summary in the
merge commit) and fixes here or there, I think that's it for the
highlights"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
powerpc/eeh: Export eeh_iommu_group_to_pe()
powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
powerpc: Reduce scariness of interrupt frames in stack traces
powerpc: start loop at section start of start in vmemmap_populated()
powerpc: implement vmemmap_free()
powerpc: implement vmemmap_remove_mapping() for BOOK3S
powerpc: implement vmemmap_list_free()
powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
powerpc/book3s: handle HMIs for cpus in nap mode.
powerpc/powernv: Invoke opal call to handle hmi.
powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
powerpc/iommu: Fix comments with it_page_shift
powerpc/powernv: Handle compound PE in config accessors
powerpc/powernv: Handle compound PE for EEH
powerpc/powernv: Handle compound PE
powerpc/powernv: Split ioda_eeh_get_state()
powerpc/powernv: Allow to freeze PE
powerpc/powernv: Enable M64 aperatus for PHB3
powerpc/eeh: Aux PE data for error log
...
Fix wrong __IO_H definition in boot/io.h
Reported-by: Fernando Silveira <fsilveira@gmail.com>
Signed-off-by: Lucas Tanure <tanure@linux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Register the controller for device tree based lookup of DMA channels
(non-fatal for backwards compatibility with older device trees) and
provide the '#dma-cells' property in the shared mpc5121.dtsi file
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver is compatible with SEC version 4.0, which was missing from
device tree resulting that the caam driver doesn't gets probed. Since
SEC is backward compatible with older versions, so this patch adds those
missing versions in c29x device tree.
Signed-off-by: Nitesh Narayan Lal <b44382@freescale.com>
Signed-off-by: Vakul Garg <b16394@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Freescale T2080/T2081 QDS Development System Board.
The T2080QDS Development System is a high-performance computing,
evaluation, and development platform that supports T2080 QorIQ
Power Architecture processor, with following major features:
T2080QDS feature overview:
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP
- Dual DIMM slots up 2133MT/s with ECC
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 8MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0, SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/MMC/eMMC Card
DMA:
- Three 8-channels DMA controllers
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
T2081QDS board shares the same PCB with T1040QDS with some differences.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power
Architecture processor cores with high-performance datapath acceleration
logic and network and peripheral bus interfaces required for networking,
telecom/datacom, wireless infrastructure, and mil/aerospace applications.
The T2080 SoC includes the following function and features:
- Four dual-threaded 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 Ethernet interfaces (multiple 1G/2.5G/10G MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
T2081 is a reduced personality of T2080 with following difference:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[scottwood@freescale.com: added fsl,qoriq-pci-v3.0 for U-Boot compat]
Signed-off-by: Scott Wood <scottwood@freescale.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The mux2 node is missing the clock-output-names field that is required
by the clk-ppc-corenet driver.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T4240 has a third DMA engine controller, so add the corresponding DMA
node into the dts file.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: reword commit message]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull kbuild updates from Michal Marek:
"Kbuild changes for v3.16-rc1:
- cross-compilation fix so that cc-option is testing the right
compiler
- Fix for make defconfig all
- Using relative paths to the object and source directory where
possible, plus fixes for the fallout of the change
- several cleanups in the Makefiles and scripts
The powerpc fix is from today, because it was only discovered
recently. The rest has been in linux-next for some time"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
powerpc: Avoid circular dependency with zImage.%
kbuild: create include/config directory in scripts/kconfig/Makefile
kbuild: do not create include/linux directory
Makefile: Fix unrecognized cross-compiler command line options
kbuild: do not add "selinux" to subdir- twice
um: Fix for relative objtree when generating x86 headers
kbuild: Use relative path when building in a subdir of the source tree
kbuild: Use relative path when building in the source tree
kbuild: Use relative path for $(objtree)
firmware: Use $(quote) in the Makefile
firmware: Simplify directory creation
kbuild: trivial - fix comment block indent
kbuild: trivial - remove trailing spaces
kbuild: support simultaneous "make %config" and "make all"
kbuild: move extra gcc checks to scripts/Makefile.extrawarn
The rule to create the final images uses a zImage.% pattern.
Unfortunately, this also matches the names of the zImage.*.lds linker
scripts, which appear as a dependency of the final images. This somehow
worked when $(srctree) used to be an absolute path, but now the pattern
matches too much. List only the images from $(image-y) as the target of
the rule, to avoid the circular dependency.
Reported-and-tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Pull powerpc updates from Ben Herrenschmidt:
"Here is the bulk of the powerpc changes for this merge window. It got
a bit delayed in part because I wasn't paying attention, and in part
because I discovered I had a core PCI change without a PCI maintainer
ack in it. Bjorn eventually agreed it was ok to merge it though we'll
probably improve it later and I didn't want to rebase to add his ack.
There is going to be a bit more next week, essentially fixes that I
still want to sort through and test.
The biggest item this time is the support to build the ppc64 LE kernel
with our new v2 ABI. We previously supported v2 userspace but the
kernel itself was a tougher nut to crack. This is now sorted mostly
thanks to Anton and Rusty.
We also have a fairly big series from Cedric that add support for
64-bit LE zImage boot wrapper. This was made harder by the fact that
traditionally our zImage wrapper was always 32-bit, but our new LE
toolchains don't really support 32-bit anymore (it's somewhat there
but not really "supported") so we didn't want to rely on it. This
meant more churn that just endian fixes.
This brings some more LE bits as well, such as the ability to run in
LE mode without a hypervisor (ie. under OPAL firmware) by doing the
right OPAL call to reinitialize the CPU to take HV interrupts in the
right mode and the usual pile of endian fixes.
There's another series from Gavin adding EEH improvements (one day we
*will* have a release with less than 20 EEH patches, I promise!).
Another highlight is the support for the "Split core" functionality on
P8 by Michael. This allows a P8 core to be split into "sub cores" of
4 threads which allows the subcores to run different guests under KVM
(the HW still doesn't support a partition per thread).
And then the usual misc bits and fixes ..."
[ Further delayed by gmail deciding that BenH is a dirty spammer.
Google knows. ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (155 commits)
powerpc/powernv: Add missing include to LPC code
selftests/powerpc: Test the THP bug we fixed in the previous commit
powerpc/mm: Check paca psize is up to date for huge mappings
powerpc/powernv: Pass buffer size to OPAL validate flash call
powerpc/pseries: hcall functions are exported to modules, need _GLOBAL_TOC()
powerpc: Exported functions __clear_user and copy_page use r2 so need _GLOBAL_TOC()
powerpc/powernv: Set memory_block_size_bytes to 256MB
powerpc: Allow ppc_md platform hook to override memory_block_size_bytes
powerpc/powernv: Fix endian issues in memory error handling code
powerpc/eeh: Skip eeh sysfs when eeh is disabled
powerpc: 64bit sendfile is capped at 2GB
powerpc/powernv: Provide debugfs access to the LPC bus via OPAL
powerpc/serial: Use saner flags when creating legacy ports
powerpc: Add cpu family documentation
powerpc/xmon: Fix up xmon format strings
powerpc/powernv: Add calls to support little endian host
powerpc: Document sysfs DSCR interface
powerpc: Fix regression of per-CPU DSCR setting
powerpc: Split __SYSFS_SPRSETUP macro
arch: powerpc/fadump: Cleaning up inconsistent NULL checks
...
