dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"
arch/arm/boot/dts/zynq-zc770-xm013.dtb: Warning (spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format error, expected "2"
arch/arm/boot/dts/zynq-zc770-xm010.dtb: Warning (spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format error, expected "1"
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dts reports incorrect usage of these properties in gpio-keys node.
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary
The patch is removing these useless properties.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Earlyconsole is used for early kernel debugging that's why this option
shouldn't be enabled by default.
Earlyconsole is partially copying the part of the bootlog after
"bootconsole [uart0] disabled".
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all Zynq device trees inline
with each other.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch removes these warnings reported by dtc 1.4:
Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Julia Cartwright <julia@ni.com>
Series-to: arm-soc
Use early console instead of earlyprintk which is supposed to use for
very early debugging (DEBUG_LL).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adds the two MIO connected pushbuttons on the zc702 board to the devicetree as a
single multi-key device for us with the gpio-keys driver.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add OCM node for all zynq boards. OCM location
can changed but for all current boards this
is the location where OCM is.`
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
parallella - Remove linux,stdout-path.
Use stdout-path to identify kernel console
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
In one pinctrl node, a 'bias-disable' property is erroneously assigned a
value.
Fixes: ARM: zynq: DT: Add pinctrl information
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add USB nodes to zc702, zc706 and zed device trees.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The fact that all supported boards use the same 33MHz crystal is a
co-incidence. The Zynq PS support a range of crystal freqs so the
hardcoded setting should be removed from the dtsi. Re-implement it
on the board level.
This prepares support for Zynq boards with different crystal
frequencies (e.g. the Digilent ZYBO).
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The used PHYs should be qualified as 'rgmii-id' instead of just 'rgmii'.
For the Zed board this seems to make a difference between working and
broken Ethernet.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adds LEDs to the zc702 devicetree for use with the leds-gpio driver.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add nodes for the Arasan SDHCI controller to Zynq dts files.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The zynq includes a Cadence GEM IP core. This is compatible with the macb driver.
Add it to the zynq-7000 DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Josh Cartwright <josh.cartwright@ni.com>
[soren: rebased to current Linus tree, added zc706 + zed support, moved phy-mode property to board level dtses]
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the default status for UARTs to disabled in the zynq-7000.dtsi file
and let board dts files enable the UARTs on demand.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Migrate the Zynq platform and its drivers to use the new clock
controller driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Use cdns,ttc because this driver is Cadence Rev06
Triple Timer Counter and everybody can use it
without xilinx specific function name or probing.
Also use standard dt description for timer
and also prepare for moving to clocksource
initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for retrieving TTC configuration from device tree. This
includes the ability to pull information about the driving clocks from
the of_clk bindings.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Make the Zynq platform use the newly created zynq clk bindings.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The purpose of the created zynq-7000.dtsi file is to describe the
hardware common to all Zynq 7000-based boards. Also, get rid of the
zynq-ep107 device tree, since it is not hardware anyone can purchase.
Add a zc702 dts file based on the zynq-7000.dtsi. Add it to the
dts/Makefile so it is built with the 'dtbs' target.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Rob Herring