This patch is to add DM support for next generation of Dell PowerVault
storage array.
Signed-off-by: Yanqing Liu <Yanqing_Liu@Dell.com>
Acked-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Universally, SCSI functions assume the lengths fed in are those of the buffer
to DMA data to, not the lengths of the data minus the header.
scsi_vpd_inquiry() assumed the latter and got it wrong, so fix up all the
functions to use the correct assumption (and fix a bug where INQUIRY in SCSI-2
dcannot go over 255).
[jejb: Matthew posted an identical version of this at the same time I did]
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
An IBM tape drive failed to complete a PERSISTENT RESERVE IN within the scsi
cmd timeout. Error recovery was initiated and it sequenced from abort through
taking the tape drive offline.
The device was taken offline because it repeatedly responded to the TUR command
issued by error recovery with a RESERVATION CONFLICT status. The tape drive
was reserved to another system. This is perfectly legitimate response to TUR,
and is one that an escalation of recovery is unlikely to clear. Further,
escalation of recovery can have undesirable side effects on the operation of
tape drives shared with other initiators.
Instead of escalating recovery, error recovery should treat the RESERVATION
CONFLICT response to the TUR as a good status, giving the issuer of the
command the opportunity to handle the timeout and reservation conflict.
Signed-off-by: Michael reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In nsp_cs_config there is a wrong struct nsp_cs_configdata allocation.
It allocates only sizeof(pointer to nsp_cs_configdata) for a whole
structure. Add a dereference to the sizeof to allocate
sizeof(nsp_cs_configdata).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The allocated struct is manually zeroed after allocation, so avoid using
the (broken) kzalloc mempool (which does not re-zero previously used items
when they are returned to the pool).
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the multiqueue mode fails to work, the driver falls back on single
queue mode. This ensures that the firmware is reinitialized with single
queue options and all the resources are readjusted accordingly.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The interrupt handler clears the interrupt status register for response
updates in the base queue while working in the multique mode. This could lead
to missing interrupt for async events, mail box completions etc. as these are
also handled in the base queue. The fix ensures that the interrupt bit is not
cleared for response updates in the ISR when the driver is working in
multiqueue mode.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
One byte added to make the IOCB structure satisfy
size requirements.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If vports are created and topology is changed to Loop only, the
driver continuously gets a LIP reset occurred and keeps trying to
enable the vport. Only manage requests during F_Port.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The RSCN processing is skipped if the event received is global and vha is not recipient.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Treat a global port-unavailable PORT_UPDATE (8014h) AEN as a
loop-down event. For this case, within the FCoE domain, the
'logical' interface has been terminated, but the driver will
not receive the classic LOOP_DOWN AEN.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Handle the parameters provided by user thru multipath.
This handler expects only 2 parameters and their value can either be 0 or 1.
This code originates from the old dm-emc.c file. Appropriate changes have
been made to make it work in the new design.
Reported-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Tested-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When we moved the device handler functionality from dm layer to SCSI layer
we dropped the parameter functionality.
This path adds an interface to scsi dh layer to set device handler
parameters.
Basically, multipath layer need to create a string with all the parameters
and call scsi_dh_set_params() after it called scsi_dh_attach() on a
device.
If a device handler provides such an interface it will handle the parameters
as it expects them.
Reported-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Tested-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Now that hot add works correctly, if a new device is added, we're still
operating on stale enclosure data, so fix that by updating the enclosure
diagnostic pages when we get notified of a device hot add
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Right at the moment, hot removal of a device within an enclosure does
nothing (because the intf_remove only copes with enclosure removal not
with component removal). Fix this by adding a function to remove the
component. Also needed to fix the prototype of
enclosure_remove_device, since we know the device we've removed but
not the internal component number
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In a situation either with expanders or with multiple enclosure
devices, hot add doesn't always work. This is because we try to find
a single enclosure device attached to the host. Fix this by looping
over all enclosure devices attached to the host and also by making the
find loop recognise that the enclosure devices may be expander remote
(i.e. not parented by the host).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ipr_cmd_label[] isn't big enough for an eight byte string plus terminator.
Fix by shortening the string to seven bytes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When bnx2i_adapter_ready() fails, connection handle(cid) = 0 is wrongly freed
because 'cid' is not yet allocated for the endpoint. Fix is to initialize
bnx2i_ep->ep_iscsi_cid to '-1' in bnx2i_alloc_ep() and not in
bnx2i_ep_connect() to avoid releasing invalid 'cid'. There is already a check
in bnx2i_free_iscsi_cid() not to free invalid iscsi connection handle (-1)
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Without the fix bnx2i would fail tt->xmit_task() when link is down and
libiscsi would have already incremented session->cmdsn before calling bnx2i's
xmit_task() entry point and will just return the command to SCSI-ML when
xmit_task() fails. libiscsi does not retract the session->cmdsn as the command
was never sent on wire. It is generally good idea for LLD, bnx2i to accept
the scsi cmnd/nopout and let upper layer timeout and go though normal session
recovery process. When link is down, unsolicited nopout will not be accepted
by bnx2i and connection will never enter recovery state. This fix is required
for MPIO to work corectly
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The phys_dev was used only to locate common offload EM instance for all
FCoE instances on a eth devices in function fcoe_em_config, so just updated
fcoe_em_config to look for actual real eth device in locating common offload
EM instance and then no need to store phys_dev in fcoe_softc, so removes
phys_dev from fcoe_softc also.
Renames fcoe_softc real_dev to netdev and updates all its uses to use netdev.
So effectively no functional change, use of single netdev instead phys_dev
and real_dev saves one pointer memory in fcoe_softc, also real_dev used here
was confusing with vlan driver terminology since real_dev in vlan driver is
referred to physical eth device.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
I don't believe this check is needed any more in the current kernel, which,
if I understand correctly, is for compound page where only the first page
is supposed to get ref-counted.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC_FRAME_SG_LEN is 4 which is too small when offload is enabled. Actually, the
WARN_ON() in fc_fcp_send_data() should be:
WARN_ON(skb_shinfo(fp_skb(fp))->nr_frags > MAX_SKB_FRAGS);
But since we will not get anything more than 64K anyway, so there is no need
to do this anyway here. Therefore, I am getting rid of FC_FRAME_SG_LEN here
and the WARN_ON here.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove the extra ifdef for NETIF_F_FSO and NETIF_F_FCOE_CRC since they are
already defined in the current kernel as in include/linux/netdevice.h.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updates fcoe_em_config to allocate a single instance of sharable offload
EM for supported lp->lro_xid per eth device, and then share this EM
for subsequently more lports creation on same eth device (e.g when using
VLAN).
Adds tiny fcoe_oem_match function for offload EM to return true for read
types IO to have read IO exchanges allocated from offload shared EM.
Removes fc_em_alloc_xid function completely which was needed to manage
two xid ranges within a EM, this is not needed any more with allocation
of separate sharable offload EM per eth device. Instead this patch adds
simple xid allocation logic to manage single xid range.
Adds fc_exch_em_alloc with mp->next_xid as cursor to allocate new xid
from single xid range of EM, uses mp->next_xid instead removed mp->last_xid
which slightly increase probability of finding empty xid on exch allocation.
Removes restriction of not allowing use of xid zero along with changing
two xid range change to single xid range.
Makes fc_fcp_ddp_setup calling conditional to only xid allocated from
shared offload EM.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modifies fcoe_hostlist_lock uses such that a new EM allocation in
fcoe_em_config and adding new fcoe_softc using fcoe_hostlist_add
are atomic, this is to ensure that a shared offload EM gets allocated
only once per eth device for its all lports.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modifies current code to use EM anchor list in EM allocation, EM free,
EM reset, exch allocation and exch lookup code paths.
1. Modifies fc_exch_mgr_alloc to accept EM match function and then
have allocated EM added to the lport using fc_exch_mgr_add API
while also updating EM kref for newly added EM.
2. Updates fc_exch_mgr_free API to accept only lport pointer instead
EM and then have this API free all EMs of the lport from EM anchor
list.
3. Removes single lport pointer link from the EM, which was used in
associating lport pointer in newly allocated exchange. Instead have
lport pointer passed along new exchange allocation call path and
then store passed lport pointer in newly allocated exchange, this
will allow a single EM instance to be used across more than one
lport and used in EM reset to reset only lport specific exchanges.
4. Modifies fc_exch_mgr_reset to reset all EMs from the EM anchor list
of the lport, adds additional exch lport pointer (ep->lp) check for
shared EM case to reset exchange specific to a lport requested reset.
5. Updates exch allocation API fc_exch_alloc to use EM anchor list and
its anchor match func pointer. The fc_exch_alloc will walk the list
of EMs until it finds a match, a match will be either null match
func pointer or call to match function returning true value.
6. Updates fc_exch_recv to accept incoming frame on local port using
only lport pointer and frame pointer without specifying EM instance
of incoming frame. Instead modified fc_exch_recv to locate EM for the
incoming frame by matching xid of incoming frame against a EM xid range.
This change was required to use EM list in libfc Rx path and after this
change the lport fc_exch_mgr pointer emp is not needed anymore, so
removed emp pointer.
7. Updates fnic for removed lport emp pointer and above modified libfc APIs
fc_exch_recv, fc_exch_mgr_alloc and fc_exch_mgr_free.
8. Removes exch_get and exch_put from libfc_function_template as these
are no longer needed with EM anchor list and its match function use.
Also removes its default function fc_exch_get.
A defect this patch introduced regarding the libfc initialization order in
the fnic driver was fixed by Joe Eykholt <jeykholt@cisco.com>.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently there is a 1:1 relationship between the lport
and exchange manager. This macro takes an EM as an argument
and determines the lport from it. However, later patches
will use an EM list per lport, so we will no longer have
this 1:1 relationship- this macro must change.
The FC_EM_DBG macro is rarely used. There are four callers,
two can use FC_LPORT_DBG instead and two can be removed
since they're not necessary. This patch makes those changes
and removes the macro.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds EM list using a anchor struct fc_exch_mgr_anchor, anchor is used
to allow same EM instance sharing across more than one lport on a eth
device, this implementation is per discussed design posted at
http://www.open-fcoe.org/pipermail/devel/2009-June/002566.html.
The shared EM is required for multiple lports on eth device when
using multiple VLANs or NPIV.
Adds fc_exch_mgr_add API to add a EM to the lport and fc_exch_mgr_del
API to delete previously added EM.
Also adds function fc_exch_mgr_destroy() to destroy allocated EM.
The kref is added to the EM to keep track of EM usage count, the EM is
destroyed when no longer in use upon kref reaching to zero.
The caller can specify match function to fc_exch_mgr_add, this
will be used in determining exchange allocation from its EM or not.
Moved calling of fcoe_em_config below fcoe_libfc_config calling,
so that list head lp->ema_list is initialized before configuring
EM.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The timer for rport retries wasn't getting canceled, and
would occasionally go off after the module was unloaded.
Add logic to cancel the timer in fc_rport_work().
Since we cancel the timer before deleting the rdata,
it is no longer necessary to do a get_device() for the pending timer.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fc_rport_logoff drops the rport lock in order to cancel work
that may be pending. This is undesirable as the state can
completely change, and the caller may not expect that the
lock could've been dropped.
If there is work pending, it will acquire the rdata mutex and
so we're protected and can change the event from READY to DELETE.
Queue the work only if there is no event already pending.
There were a couple other cases where the state was set to
DELETE and work queued, even though the state may have already
been DELETE. Fix these using a common function fc_rport_enter_delete().
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
State RPORT_ST_NONE was intented to be an invalid state (0), never used.
This was a misguided attempt to be sure it was always initialized.
Having an extra state meaning nothing requires switch statements to
have a case covering that state.
State NONE has been used instead to mean the remote port is being deleted.
Changing the name to RPORT_ST_DELETE.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We saw periodic messages like:
WARNING: at drivers/scsi/libfc/fc_exch.c:825 fc_seq_start_next+0x30/0x4b
This was due to trying to allocate a sequence in a request handler
when the exchange had been reset.
Delete the WARN_ON.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
During an fcoe module unload, we saw a problem where fc_rport_work()
finds the lport has been freed. The rdata points to an area
containing 0x6b6b6b6b... the pool poison value from kmem_free().
In fcoe_if_destroy() we call fc_fabric_logoff() then fc_lport_destroy().
fc_fabric_logoff() flushes the remote port work, but we're still receiving
requests, and an RSCN or PLOGI arrives which creates more rports.
Note that although the LLD also checks link_up, it doesn't do it
under the lport mutex, so it can deliver frames to
fc_lport_recv_req() even after link_up is cleared.
So, re-check link_up there.
We need to flush the rports by calling disc_stop_final()
after we clear link_up.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When removing the fcoe module, several lports were being shut down
through fc_lport_fabric_logoff().
Occasionally, one would enter reset state before fc_lport_destroy()
was called, and since link_up was still true, it would log back in.
If we just clear link_up earlier, then we wouldn't be accepting LOGO
requests from other initiators while we are shutting down.
Fix by changing the LOGO response handler to enter DISABLED instead
of RESET. Add an fc_lport_enter_disabled() function which does
what fc_lport_enter_reset() did, except it doesn't proceed to FLOGI state.
Move the code that was common between fc_lport_enter_reset() and
fc_lport_enter_disabled() into a new fc_lport_reset_locked() function.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The state NONE was meant to be invalid, but has been used as
the initial state. Rename it to be DISABLED, as more descriptive.
Further patches will make it the like the RESET state, except
it won't transition to FLOGI until fc_lport_fabric_login() is called.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To be more sure that no more input arrives at the local port as
it is being destroyed, clean the queues in the per-cpu receive
threads.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
No need to check phys_dev here, just call dev_ethtool_get_settings() directly
will take care of this.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When encap the els for FIP, set the fip_flags according to the FCF and lport's
capability of supporting SPMA or FPMA or both.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix this bug of validating the wrong mac address while checking for SAN MAC
address support from LLD as we should check ha->addr not ctlr.ctl_src_addr.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
alua_activate only sends a STPG if only explicit is suppored.
As a result, for EMC targets that support both we end up doing
a implicit failover when X commands are finally sent to
the other SP.
This patch does a AND on the h->tpgs, so we do a explicit failover
right away.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There are two setup places for max_phys in scsi_transport_sas.c; one
incorrectly places a NULL into host_attrs instead of port_attrs. Remove it.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update driver version to 8.3.4
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove spaces before newlines in several log messages
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add bsg (SGIOv4) support for sending and receiving ELS, CT commands
This patch adds a new file, lpfc_bsg.c.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a pair of FCoE issues
- Fix Region 23 FCoE Parameters not being read correctly
- Fix race condition when there are FCoE events during FCF table read
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Consistently implement persistent port disable.
Ability was to be managed in the adapter via firmware via flash settings.
However, not all firmware images supported it. Uniformly support it
everywhere.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Various SLI4 fixes
- Fix switch name not used in the FCF record for FCoE HBAs
- Enabled HBA UE error polling error-condition action code
- Rewrite lpfc_sli4_scmd_to_wqidx_distr() to handle counter rollover cleanly
- Modify resume_rpi mailbox data structure to match current SLI4 spec
- Do not issue mailbox command in MBX_POLL mode when LPFC_HBA_ERROR is set
- Wait for HBA POST completion before checking Online and UE registers
- Fix accumulated total length not being filled in on unsolicited IOCBs
- Use PCI config space register to determine SLI rev of HBA
- Turn on starting ELS tmo function timer during device initialization
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
print_mac is being deprecated, and %pM makes for smaller
code anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When kzalloc fails in lpfc_hba_alloc, don't dereference the NULL by
lpfc_printf_log. Use dev_err instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-By: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On ppc64, gcc 4.4 spews lots of..
drivers/scsi/qla2xxx/qla_def.h:1485:7: warning: "__LITTLE_ENDIAN" is not defined
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When using iface, bnx2i was unable to offload further connections after all
active sessions are logged out. bnx2i will unregister the device from cnic
when the last connection is torn down. Next call to ep_connect() will fail
because the device is not registered. This issue is not seen if shost == NULL
is passed to ep_connect() call because in that case bnx2i will registers all
known devices with cnic before doing a route look-up. When shost != NULL,
bnx2i knows the device on which to offload the connection and has to register
this device before attempting to offload the connection
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Change function parameter name in kernel-doc to match the function's
actual parameter name, to fix 2 kernel-doc warnings.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
convert bnx2i_dev_lock to type mutex from rwlock_t because
cnic->register_device() can sleep for various reasons including memory
allocation, waiting for ISCSI_INIT completion and while acquiring mutex lock,
cnic_lock.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed bnx2i_init_one() to properly handle return code of
cnic->register_device() and propagate it back to the caller. No need to check
for BNX2I_CNIC_REGISTERED, because unless the adapter is added to adapter_list
it will not be registered in ep_connect context
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed bnx2i_reg_devices as this counter is not really
used in a meaningful way
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a request fails we print the sense data but not the actual command
that failed. Add a printout of the operation + CDB for failed commands.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Problem reported: http://marc.info/?l=dm-devel&m=124585978305866&w=2
scsi_dh does not do a refernce count for attach/detach, and this affects
the way it is supposed to work with multipath when a device is not
in the dev_list of the hardware handler.
This patch adds a reference count that counts each attach.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It has been 3 years since this file was sync-ed with
www.t10.org . Information taken from the last bunch
of drafts released in May 2009. More asc/ascq codes
are coming for thin provisioning; when approved and
allocated another patch could add them prior to this
patch going live.
Changelog:
- add some new command names and rename two commands
- sync asc/ascq table with www.t10.org/lists/asc-num.txt
- correct bug in scsi_extd_sense_format() [second
for loop]
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Moving the setting and clearing of the mutex's to
_config_request. There was a mutex deadlock when diag reset is called from
inside _config_request, so diag reset was moved to outside the mutexs.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix another ocurring when the system resumes. This oops was due to driver
setting the pci drvdata to NULL on the prior hibernation. Becuase it was
set to NULL, upon resmume we assume the pci drvdata is non-zero, and we oops.
To fix the ooops, we don't set pci drvdata to NULL at hibernation time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix oops ocurring at hibernation time. This oops was due to the firmware fault
watchdog timer still running after we freed resources. To fix the issue we need
to terminate the watchdog timer at hibernation time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This restriction is introduced just to avoid loop of
config_request. Retry must be limited so we have restricted
config request to maximum 2 times.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Inhibit 0x3117 loginfos - during cable pull, there are too many printks going
to the syslog, this is have impact on how fast the interrupt routine can handle
keeping up with command completions; this was the root cause to the config
pages timeouts.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a volume is activated, the driver will recieve a pair of ir config change
events to remove the foreign volume, then add the native.
In the process of the removal event, the hidden raid componet is removed from
the parent.When the disks is added back, the adding of the port fails becuase
there is no instance of the device in its parent.
To fix this issue, the driver needs to call mpt2sas_transport_update_links()
prior to calling _scsih_add_device. In addition, we added sanity checks on
volume add and removal to ignore events for foreign volumes.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kernel panic is seen because driver did not tear down the port which should
be dnoe using mpt2sas_transport_port_remove(). without this fix When expander
is added back we would oops inside sas_port_add_phy.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kernel panic is seen because of enclosure_handle received from FW is zero.
Check is introduced before calling mpt2sas_config_get_enclosure_pg0.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Changing to GFP_ATOMIC because the only caller in cnic/bnx2i may
be calling this function while holding spin_lock.
This problem was discovered by Mike Christie.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some USB devices crash when we send them an inquiry with the EVPD bit
set, regardless of page requested (i.e. including page 0).
We only need the extended inquiry to gain access to VPD pages 0xB0 and
0xB1. These appeared in SBC2 and SBC3 respectively, so we can restrict
sending the extended inquiry to devices reporting SPC3 or higher.
This fixes bugzilla.kernel.org #13657.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[jejb: added comment]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hotplug of phys which form wide ports simply does not work at the moment. Fix
this by adding checks at the hotplug points to see if the attached sas address
of the phy already exists (in which case it's part of a wide port) and act
accordingly.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
[jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower
case to fix a ppc64 compile error in linux-next]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently the fc_exch_rrq is called with fc_exch's ex_lock held.
The fc_exch_rrq allocates new exch and that requires taking
ex_lock again after EM lock. This locking order causes warning,
see more details on this warning at :-
http://www.open-fcoe.org/pipermail/devel/2009-July/003251.html
This patch fixes this by dropping the ex_lock before calling
fc_exch_rrq().
The fc_exch_rrq needs to grab ex_lock lock again to schedule
RRQ retry and in the meanwhile fc_exch_reset could occur before
ex_lock is grabbed inside fc_exch_rrq. So to handle this case,
this patch adds additional check to detect fc_exch_reset after
ex_lock acquired and in case the fc_exch_reset occurred then
abandons the RRQ retry and releases the exch.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removed unnecessary hiwat code to free up the number available IOCBs.
Eliminates unnecessary eh_ escalations due to inability to obtain IOCB
pkt for marker.
v2.
- Remove define not used anymore and fix req_q_coun accounting.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: ported patch from qlogic.com driver to upstream]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
eh_device_reset may be called from scsi error handler or sg_reset, etc.
When called from sg_reset, there will not be an associated srb. The
driver should lookup the corresponding device handle given information
from the supplied cmd structure and should not assume that there exists
an srb.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixed driver bug where adapter recovery did not complete if there were
outstanding commands detected on that host adapter.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recently dm-multipath began calling blk_abort_queue. This causes all the
commands/request running on the path to have the timeout function called.
If a path does go down, and the LLD returns DID_*, dm-multpiath will eventually
get this error and begin to call the cmd timeout handler. qla4xxx currently
does not set a timed out handler and so the default one could return
BLK_EH_NOT_HANDLED and end up firing the scsi eh and stopping IO to all
paths on the host when only one path is affected.
For software and offload iscsi we have a timed out handler already.
This patch adds a driver specific one to qla4xxx because there
are some ddb->state and session->state and command completion races
that are better handled in the LLD.
This also handles the problem where if the session is down,
we do not need the scsi eh to run until the transport code
has tried to reconnect us.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixed sense data errors occurring above the first 32 bytes,
as required by some third party applications. Sense data
in the first 32 bytes has always been correct.
Patch updated to use srb data variables instead of scsi command
scratchpad data area, as scratchpad area is already used.
Also, corrected debug print alignment bug in dump_buffer routine.
Changed KERN_DEBUG to KERN_INFO in printk statements in this routine.
Changed version number to 5.01.00-k9
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: fixed checkpath.pl errors]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The session lock can be held in the scsi eh thread or the completion
paths run from the net softirq. This disables bhs in iscsi_eh_abort when
taking the session lock.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a hotplug problem in the way libsas allocates ports: it loops over the
available ports first trying to add to an existing for a wide port and
otherwise allocating the next free port. This scheme only works if the port
array is packed from zero, which fails if a port gets hot unplugged and the
array becomes sparse. In that case, a new port is formed even if there's a
wide port it should be part of. Fix this by creating two loops over all the
ports: the first to see if the phy should be part of a wide port and the
second to form a new port in an empty port slot.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I overlooked SG_DXFER_TO_FROM_DEV support when I converted sg to use
the block layer mapping API (2.6.28).
Douglas Gilbert explained SG_DXFER_TO_FROM_DEV:
http://www.spinics.net/lists/linux-scsi/msg37135.html
=
The semantics of SG_DXFER_TO_FROM_DEV were:
- copy user space buffer to kernel (LLD) buffer
- do SCSI command which is assumed to be of the DATA_IN
(data from device) variety. This would overwrite
some or all of the kernel buffer
- copy kernel (LLD) buffer back to the user space.
The idea was to detect short reads by filling the original
user space buffer with some marker bytes ("0xec" it would
seem in this report). The "resid" value is a better way
of detecting short reads but that was only added this century
and requires co-operation from the LLD.
=
This patch changes the block layer mapping API to support this
semantics. This simply adds another field to struct rq_map_data and
enables __bio_copy_iov() to copy data from user space even with READ
requests.
It's better to add the flags field and kills null_mapped and the new
from_user fields in struct rq_map_data but that approach makes it
difficult to send this patch to stable trees because st and osst
drivers use struct rq_map_data (they were converted to use the block
layer in 2.6.29 and 2.6.30). Well, I should clean up the block layer
mapping API.
zhou sf reported this regiression and tested this patch:
http://www.spinics.net/lists/linux-scsi/msg37128.htmlhttp://www.spinics.net/lists/linux-scsi/msg37168.html
Reported-by: zhou sf <sxzzsf@gmail.com>
Tested-by: zhou sf <sxzzsf@gmail.com>
Cc: stable@kernel.org
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: finally remove the obsolete variable $TOPDIR
gitignore: ignore scripts/ihex2fw
Kbuild: Disable the -Wformat-security gcc flag
gitignore: ignore gcov output files
kbuild: deb-pkg ship changelog
Add new __init_task_data macro to be used in arch init_task.c files.
asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
Add new macros for page-aligned data and bss sections.
asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] cxgb3i: fix connection error when vlan is enabled
[SCSI] FC transport: Locking fix for common-code FC pass-through patch
[SCSI] zalon: fix oops on attach failure
[SCSI] fnic: use DMA_BIT_MASK(nn) instead of deprecated DMA_nnBIT_MASK
[SCSI] fnic: remove redundant BUG_ONs and fix checks on unsigned
[SCSI] ibmvscsi: Fix module load hang
The initial patches to support this through sysfs export were broken
and have been if 0'ed out in any release. So lets just kill the code
and reclaim some space in struct request_queue, if anyone would later
like to fixup the sysfs bits, the git history can easily restore
the removed bits.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There is a bug when VLAN is configured on the cxgb3 interface, the iscsi
conn. would be denied with message "cxgb3i: NOT going through cxgbi device."
This patch adds code to get the real egress net_device when vlan is configured.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I recently discovered on my zalon that if the attachment fails because
of a bus misconfiguration (I scrapped my HVD array, so the card is now
unterminated) then the system oopses. The reason is that if
ncr_attach() returns NULL (signalling failure) that NULL is passed by
the goto failed straight into ncr_detach() which oopses.
The fix is just to return -ENODEV in this case.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Robert Love reported warning while building fnic_main.c:
drivers/scsi/fnic/fnic_main.c:478: warning: `DMA_nnBIT_MASK' is deprecated.
Replaced use of DMA_nnBIT_MASK by DMA_BIT_MASK(nn)
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The shost sg tablesize is set to FNIC_MAX_SG_DESC_CNT and fnic uses
scsi_dma_map, so both BUG_ONs can be removed.
scsi_dma_map may return -ENOMEM, sg_count should be int to catch that.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixes a regression seen in the ibmvscsi driver when using the VSCSI
server in SLES 9 and SLES 10. The VSCSI server in these releases
has a bug in it in which it does not send responses to unknown MADs.
Check the OS Type field in the adapter info response and do not send
these unsupported commands when talking to an older server.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
BUS_ID_SIZE is being removed from the kernel.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If a SCSI ULD driver sets blk_queue_prep_rq(), it should clean it
up itself on remove(), and not from the bus callbacks. This
removes the need to hook into bus->remove(), which should not
be used at the same time as driver->remove().
[jejb: fix sdkp initialisation problem due to mismerge]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
setting err as -EOVERFLOW for Too many iscsi targets.
Also fixes a spurious compiler warning for gcc 4.3.3 and gcc 4.4 :
CC drivers/scsi/scsi_transport_iscsi.o
drivers/scsi/scsi_transport_iscsi.c: In function ‘iscsi_add_session’:
drivers/scsi/scsi_transport_iscsi.c:678: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The return value from BSG timout function should be based on the state of the
BSG job. This helps block layer to take selective actions to clean up BSG job.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Registered the softirq_done function, since this is requried iby an request
using block level request timeout functionality. This function will be called
by the block layer as part of time out clean process to release the BSG
request.
Moved some of the BSG request completion activities to softirq_done routine to
take care of both normal and timout completions.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This makes a huge difference when you have a serial console on bootup to limit
these messages to a sane number.
Signed-off-by: John Stoffel <john@stoffel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
People keep sending patches to expose CONFIG_SCSI_WAIT_SCAN as a tunable
item. These patches aren't accepted upstream, so let's stop the ongoing
irritation of people due to the unconditionally installed module and its
Kconfig symbol.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixes a problem seen where sending a PRLI to a target
resulted in it sending a LOGO. This caused the ibmvfc
driver to go back through discovery again, which caused
another PRLI attempt, which caused another LOGO. Fix this
behavior by ignoring LOGO if we haven't even logged into
the target yet.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since async events could indicate changes to link status, or
events which could affect decisions made during discovery, we should
process async events prior to command completion responses.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds the /sys/module/libfc/parameters/debug_logging
file to sysfs as a module parameter. It accepts an integer
bitmask for logging. Currently it supports:
bit
LSB 0 = general libfc debugging
1 = lport debugging
2 = disc debugging
3 = rport debugging
4 = fcp debugging
5 = EM debugging
6 = exch/seq debugging
7 = scsi logging (mostly error handling)
the other bits are not used at this time.
The patch converts all of the libfc source files to use
these new macros and removes the old FC_DBG macro.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds a 'debug_logging' module parameter to
libfcoe.ko. It is an unsigned int that represents a bitmask of
available debug logging levels, each of which can be tuned at
runtime. Currently there are only two logging levels for this
module-
bit
LSB 0 = libfcoe general logging
1 = FIP logging
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts all FC_DBG statements to use new runtime tunable
debug macros. The fcoe.ko module now has a debug_logging module
parameter.
fcoe_debug_logging is an unsigned integer representing a bitmask of all
available logging levels. Currently only two logging levels are
supported-
bit
LSB 0 = general fcoe logging
1 = netdevice related logging
This patch also attempts to clean up some debug statement formatting
so it's more readable.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for setting the physical block exponent and
lowest aligned LBA in the READ CAPACITY(16) response.
The B0 VPD page is adjusted accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
NETDEVICES + NETDEV_1000 need to be enabled so that kconfig will check
those branches for selects and enforce "select UIO" under CNIC.
Otherwise the build fails with:
ERROR: "uio_unregister_device" [drivers/net/cnic.ko] undefined!
ERROR: "uio_event_notify" [drivers/net/cnic.ko] undefined!
ERROR: "__uio_register_device" [drivers/net/cnic.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
MSI has only been tested on and known to work with PCI-E based adapters. This
patch adds a field to struct ipr_chip_t to indicate which type of interrupt to
use based on what is known about the chip.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The return value from pci_enable_msi() can not always be trusted. This patch
adds code to generate an interrupt after MSI has been enabled and tests
whether or not we can receive and process it. If the tests fails, then fall
back to LSI.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There have been several bug reports which identified the Ultrium-3
tape as just hanging up on the bus during certain types of IU
transfer. The identified culpret is type 0x02 (MULTIPLE COMMAND)
transfers. The only way to prevent this tape wedging is to prevent it
from using IU transfers at all. So this patch uses the exported
blacklist matching technology to recognise the drive and force it not
to use IU transfers.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Right at the moment, we carefully set up the spi_support_xx in the
device configuration routines, but then we never actually use the
results: we rely on the inquiry strings. If we're going to allow
overrides to the inquiry data, we have to rely on our own internal
settings.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current scsi_devinfo.c matching routines use a single table for
the global blacklist. However, we're developing a need to blacklist
from specific transports too (notably some tape drives using SPI which
don't respond well to high speed protocols). Instead of developing
separate blacklist matching for each transport class needing it,
enhance the current list matching to permit multiple lists.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP24xx chips have dedicated uses for mailbox 4 and 5 which
software should typically not query nor update.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* To set iiDMA speeds for ISP81XX, bits 5-0 are used whereas for
other older ISPs bits 2-0 are used.
* Pass proper VP index
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Just once, two fcoe instances got the same host number
from scsi_add_host().
Use atomic_t and atomic_inc_return() to get next host number.
Subtract 1, so that scsi_host still starts with 0.
[jejb: added comment about unusual subtraction]
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We need to call blk_end_request_all to complete SMP requests properly.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Allow the user to control the debug logs in libiscsi. We will now
have a module param for connection, session & error handling.
[Mike Christie - Fixed up to compile on current code and added
missing ISCSI_DBG_EH conversions]
Signed-off-by: Erez Zilber <erezzi.list@gmail.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The net layer might return -EAGAIN because it could not
get space/mem within the sock sndtimeo or becuase the tcp/ip
connection was down. For the latter we do not want to retry
because the conn/session should just be shutdown and restarted.
libiscsi knows the state of the session recovery so propogate
this error to that layer. It will either do iscsi recovery
or have us retry the operation. Right now if we have partially
sent a pdu we would always retry the IO xmit slowing down
recovery.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we are sending or receiving data for the task successfully do
not run the scsi eh, because we know the task is making progress.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The default kernel pages supported are 4K, 8K, 16K, and 64K. Re-calculate
entries if PAGE_SIZE is not one of the defaults.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The iscsi ddp functionality could be used by multiple iscsi entities,
add a refcnt to keep track of it, so we would not release it pre-maturely.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Query the block limits VPD page and adjust queue minimum and optimal I/O
sizes.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Detect non-rotational devices and set the queue flag accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Extract physical block size and lowest aligned LBA from READ
CAPACITY(16) response and adjust queue parameters.
Report physical block size and alignment when applicable.
[jejb: fix up trailing whitespace]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.
And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.
debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/
Fix inconsistency of directory name to mount debugfs filesystem.
* From Steven Rostedt
- find_debugfs() and tracing_files() in this patch.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-scsi@vger.kernel.org
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-scsi@vger.kernel.org
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows the Adaptec firmware to pass on its values for Packetize and
QAS. To do this, the settings max_iu and max_qas have been introduced into
the SPI transport class and populated from the adaptec NVram tables. Domain
validation in the SPI transport class will respect the max settings when
configuring to the highest possible speed for testing.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We already have blacklists for SGI, IBM and SUN versions of this; apparently
there's a Dell version too.
Reported-by: Thomas Witzel <witzel.thomas@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Patch was originally submitted upstream on 4/21/2008:
http://marc.info/?l=linux-scsi&m=120880973719266&w=2
Somewhere, it never get merged. The patch restructures the task mgmt
routines, commonizing like behavior. Then the patch changes device
reset to LUN resets, and adds a target reset handler.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes:
- Fixed error paths retaking a spin lock which they already hold
- Added code to free memory in a couple of error paths
- Added code to free RPI bit map while unloading driver
- Added code to write zero to memory object allocated through dma_alloc_coherent
- Fixed crash/hang with target or LUN resets
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contains the following changes:
- Force vport to send LOGO to fabric controller when deleting vport
- Fixed driver failing to register login when a PLOGI is received
- Fixes for FIP discovery
- Added stricter checks for FCF addressing mode
- Added code to send only FLOGI, FDISC and LOGO to Fabric controller as FIP
- Fixed handling of LOGO from Fabric port
- Fixed consecutive link up events skipped link_down processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
