This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.
This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.
For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit efdfeb079c
("regulator: fixed: Convert to use GPIO descriptor only")
switched to use gpiod_get() to look up the regulator from the
gpiolib core whether that is device tree or boardfile.
This meant that we activate the code in
a603a2b8d8 ("gpio: of: Add special quirk to parse regulator flags")
which means the descriptors coming from the device tree already
have the right inversion and open drain semantics set up from
the gpiolib core.
As the fixed regulator was inspected again we got the
inverted inversion and things broke.
Fix it by ignoring the config in the device tree for now: the
later patches in the series will push all inversion handling
over to the gpiolib core and set it up properly in the
boardfiles for legacy devices, but I did not finish that
for this kernel cycle.
Fixes: commit efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we augmented the regulator core to accept a GPIO descriptor instead
of a GPIO number, we can augment the fixed GPIO regulator to look up
and pass that descriptor directly from device tree or board GPIO
descriptor look up tables.
Some boards just auto-enumerate their fixed regulator platform devices
and I have assumed they get names like "fixed-regulator.0" but it's
pretty hard to guess this. I need some testing from board maintainers to
be sure. Other boards are straight forward, using just plain
"fixed-regulator" (ID -1) or "fixed-regulator.1" hammering down the
device ID.
It seems the da9055 and da9211 has never got around to actually passing
any enable gpio into its platform data (not the in-tree code anyway) so we
can just decide to simply pass a descriptor instead.
The fixed GPIO-controlled regulator in mach-pxa/ezx.c was confusingly named
"*_dummy_supply_device" while it is a very real device backed by a GPIO
line. There is nothing dummy about it at all, so I renamed it with the
infix *_regulator_* as part of this patch set.
Intel MID portions tested by Andy.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Check the x86 BCM stuff
Acked-by: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 13bed58ce8 (regulator: fixed: add support for ACPI
interface).
While there does appear to be a practical need to manage regulators on ACPI
systems, using ad-hoc properties to describe regulators to the kernel presents
a number of problems (especially should ACPI gain first class support for such
things), and there are ongoing discussions as to how to manage this.
Until there is a rough consensus, revert commit 13bed58ce8, which hasn't
been in a released kernel yet as discussed in [1] and the surrounding thread.
[1] http://lkml.kernel.org/r/20170125184949.x2wkoo7kbaaajkjk@sirena.org.uk
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to retrieve fixed voltage configure information through
ACPI interface. This is needed for Intel Bay Trail devices, where a
GPIO is used to control the USB vbus.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO interface of_get_named_gpio() has implemented the proper
error returns even EPROBE_DEFER and hence caller need not to
implement any workaround for translating the returned error.
Remove the workaround implemented to handle the return of
of_get_named_gpio().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The of_get_regulator_init_data() function is used to extract the regulator
init_data but information on how to extract certain data is defined in the
static regulator descriptor (e.g: how to map the hardware operating modes).
Add a const struct regulator_desc * parameter to the function signature so
the parsing logic could use the information in the struct regulator_desc.
of_get_regulator_init_data() relies on of_get_regulation_constraints() to
actually extract the init_data so it has to pass the struct regulator_desc
but that is modified on a later patch.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use gpio_is_valid instead of an explicit comparison with 0.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch sets ena_gpio_initialized for all drivers which set a
ena_gpio from parsed DT properties. Drivers using pdata may get zero
initialized pdata and therefore copy a 0 into the regulator_config
ena_gpio field.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use more compact of_property_read_{bool|u32}() calls instead of the
of_{find|get}_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update the code to use devm_* API so that driver core will manage
resources.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warnings.
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide the rail supply voltage through descriptor to the
core and remove the callbacks which implement the get_voltage
and list_voltage.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for input supply in DT parsing of node.
The input supply will be provided by the property
"vin-supply" in the regulator node.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is essentially the code that was factored out into the core when the
feature was implemented.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_get_named_gpio() needs the driver hosting the GPIO that the DT
property references to have been probed. Detect this specific failure,
and defer the probe of the whole regulator until this API can complete.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the new of_match_ptr() macro for the of_match_table
pointer entry to avoid having to #define match NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add property for the gpio flag open drain when registering
fixed regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All the drivers that need delay for the regulator voltage output voltage to
stabilize after being enabled or after being set to a new value has been
converted to implement enable_time and set_voltage_time_sel callbacks.
Then regulator core will take care of the necessary delay.
For the drivers that don't need the delay, don't need to include linux/delay.h.
This patch removes the unneeded include of linux/delay.h in regulator drivers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than adding new arguments to regulator_register() every time we
want to add a new bit of dynamic information at runtime change the function
to take these via a struct. By doing this we avoid needing to do further
changes like the recent addition of device tree support which required each
regulator driver to be updated to take an additional parameter.
The regulator_desc which should (mostly) be static data is still passed
separately as most drivers are able to configure this statically at build
time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adding flag on fixed regulator board configuration structure
to specify whether gpio is open drain type or not.
Passing this information to gpio library when requesting
gpio so that gpio driver can set the pin state accordingly,
for open drain type:
- Pin can be set HIGH as setting as input, PULL UP on
pin make this as HIGH.
- Pin can be set LOW as setting it as output and drive to LOW.
The non-open drain pin can be set HIGH/LOW by setting it to
output and driving it to HIGH/LOW.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than replicating the core support for always on regulators use
a different set of ops with none of the enable related operations provided
when we don't have any ops. This ensures that we automatically pick up
any enhanced support for such regulators that the core has such as the
warnings about regulation constraints that can't be used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If used as a dummy voltage provider the fixed regulator should
not set n_voltages to make the core accept the device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix fixed regulator using DT failed to call regulator_register.
of_get_regulator_init_data set apply_uV to 1, but fixed regulator
doesn't need it. Set it back to 0.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_get needs of_node to find right regulator.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's not always true that the device_node of regulator can be found
at dev->of_node at the time when of_get_regulator_init_data() is being
called, because in some cases the regulator nodes in device tree do
not have 'struct device' behind them until regulator_dev gets created
for it by core function regulator_register().
The patch adds device_node as a new parameter to
of_get_regulator_init_data(), so that caller can pass in the node of
regulator directly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_get_fixed_voltage_config() may return NULL, return -ENOMEM in this case
so we don't dereference NULL pointer.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_get_regulator_init_data() may return NULL, thus
check the return value to avoid NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The fixed regulator driver uses of_get_fixed_voltage_config()
to extract fixed_voltage_config structure contents from device tree.
Also add documenation for additional bindings for fixed
regulators that can be passed through dt.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't know what voltage the regulator is set to return an error
rather than reporting zero volts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Another group of drivers that are taking advantage of the implicit
presence of module.h -- and will break when we pull the carpet out
from under them during a cleanup. Fix 'em now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Add __devinit/__devexit markings to probe and remove methids of the
driver, change types of variables containing boolean data to boolean,
set up driver's owner field so we have proper sysfs link between
driver and the module.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Linus Walleij