This patch fixes a long standing issue introduced during the 3.16 merge window.
Shortly after the merge, exynos5250-based arndale boards began to produce the
following errors:
kern.err kernel: exynos-cpufreq exynos-cpufreq: failed to set cpu voltage
kern.err kernel: cpufreq: __target_index: Failed to change cpu frequency: -22
Further analysis revealed that the S5M8767 voltage regulator used on the
exynos5250-based arndale board utilizes the S3C2410 I2C controller. If the
S3C2410 I2C controller driver is not enabled, the S5M8767 voltage regulator
fails to probe. Therefore a dependency exists between these two drivers.
In the exynos_defconfig both CONFIG_REGULATOR_S5M8767 and CONFIG_I2C_S3C2410
options are enabled, and no errors are produced. However, in the
multi_v7_defconfig only the CONFIG_REGULATOR_S5M8767 option is enabled and the
errors are present. So let's enable the CONFIG_I2C_S3C2410 option in the
multi_v7_defconfig to allow the S5M8767 voltage regulator to probe.
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This contains the serial port numbering fixes that are required for the
serial port numbering to stay the same with or without the serial core
making use of the aliases defined in DT.
eMMC is also fixed for TN7 and Roth boards which were using the wrong
regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ick3
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.18-fixes-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into fixes
Pull "ARM: tegra: Device tree fixes for v3.18-rc5" from Thierry Reding:
This contains the serial port numbering fixes that are required for the
serial port numbering to stay the same with or without the serial core
making use of the aliases defined in DT.
eMMC is also fixed for TN7 and Roth boards which were using the wrong
regulators.
* tag 'tegra-for-3.18-fixes-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: roth: Fix SD card VDD_IO regulator
ARM: tegra: Remove eMMC vmmc property for roth/tn7
ARM: dts: tegra: move serial aliases to per-board
ARM: tegra: Add serial port labels to Tegra124 DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Correct IIC0 parent clock on r8a7740
* Correct SD3CKCR address to device tree on r8a7790
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Du2A
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC DT Fixes for v3.18" from Simon Horman:
* Correct IIC0 parent clock on r8a7740
* Correct SD3CKCR address to device tree on r8a7790
* tag 'renesas-dt-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740 dtsi: Correct IIC0 parent clock
ARM: shmobile: r8a7790: Fix SD3CKCR address to device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Set i2c clks_per_count to 2 on kzm9g
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e8cy
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v3.18" from Simon Horman:
* Set i2c clks_per_count to 2 on kzm9g
* tag 'renesas-soc-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g legacy: Set i2c clks_per_count to 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A fix for the A31 dma controller that requires the AHB clock to be parented to
PLL6 in order to operate.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SmW6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 3.18" from Maxime Ripard:
A fix for the A31 dma controller that requires the AHB clock to be parented to
PLL6 in order to operate.
* tag 'sunxi-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Another small set of fixes:
- Some DT compatible typo fixes
- irq setup fix dealing with irq storms on orion
- i2c quirk generalization for mvebu
- A handful of smaller fixes for OMAP
- A couple of added file patterns for OMAP entries in MAINTAINERS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0RR/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another small set of fixes:
- some DT compatible typo fixes
- irq setup fix dealing with irq storms on orion
- i2c quirk generalization for mvebu
- a handful of smaller fixes for OMAP
- a couple of added file patterns for OMAP entries in MAINTAINERS"
* tag 'armsoc-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: at91/dt: Fix sama5d3x typos
pinctrl: dra: dt-bindings: Fix output pull up/down
MAINTAINERS: Update entry for omap related .dts files to cover new SoCs
MAINTAINERS: add more files under OMAP SUPPORT
ARM: dts: AM437x-SK-EVM: Fix DCDC3 voltage
ARM: dts: AM437x-GP-EVM: Fix DCDC3 voltage
ARM: dts: AM43x-EPOS-EVM: Fix DCDC3 voltage
ARM: dts: am335x-evm: Fix 5th NAND partition's name
ARM: orion: Fix for certain sequence of request_irq can cause irq storm
ARM: mvebu: armada xp: Generalize use of i2c quirk
Some DT files had a typo with a missing "5" in sama5d3x first compatible string.
Signed-off-by: Peter Rosin <peda@axentia.se>
[nicolas.ferre@atmel.com: modify commit log]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
MAINTAINERS file to avoid missing PMIC and SoC related patches:
- Fix random hangs on am437x because of incorrect default
value for the DDR regulator
- Fix wrong partition name for NAND on am335x-evm
- Fix wrong pinctrl defines for dra7xx
- Update maintainers entries for PMICs and SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YQGC
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-against-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.18-rc4" from Tony Lindgren:
Few omap fixes for hangs and wrong pinctrl defines, and update
MAINTAINERS file to avoid missing PMIC and SoC related patches:
- Fix random hangs on am437x because of incorrect default
value for the DDR regulator
- Fix wrong partition name for NAND on am335x-evm
- Fix wrong pinctrl defines for dra7xx
- Update maintainers entries for PMICs and SoCs
* tag 'omap-fixes-against-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
pinctrl: dra: dt-bindings: Fix output pull up/down
MAINTAINERS: Update entry for omap related .dts files to cover new SoCs
MAINTAINERS: add more files under OMAP SUPPORT
ARM: dts: AM437x-SK-EVM: Fix DCDC3 voltage
ARM: dts: AM437x-GP-EVM: Fix DCDC3 voltage
ARM: dts: AM43x-EPOS-EVM: Fix DCDC3 voltage
ARM: dts: am335x-evm: Fix 5th NAND partition's name
Signed-off-by: Olof Johansson <olof@lixom.net>
- Armada XP
- Generalize i2c quirk
- orion
- Fix irq storm caused by specific sequence of request_irq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JCsp
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.18' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu fixes for v3.18" from Jason Cooper:
- Armada XP
- Generalize i2c quirk
- orion
- Fix irq storm caused by specific sequence of request_irq
* tag 'mvebu-fixes-3.18' of git://git.infradead.org/linux-mvebu:
ARM: orion: Fix for certain sequence of request_irq can cause irq storm
ARM: mvebu: armada xp: Generalize use of i2c quirk
Pull ARM fixes from Russell King:
"Two fixes this time, one to ensure that the kuser helper option
depends on MMU as they aren't available for noMMU targets (and if the
option is selected, we end up oopsing.)
The second fix plugs a corner case with the decompressor, ensuring
that the instruction stream can see the relocated code in every case
on ARMv7 CPUs"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8198/1: make kuser helpers depend on MMU
ARM: 8191/1: decompressor: ensure I-side picks up relocated code
The kuser helpers page is not set up on non-MMU systems, so it does
not make sense to allow CONFIG_KUSER_HELPERS to be enabled when
CONFIG_MMU=n. Allowing it to be set on !MMU results in an oops in
set_tls (used in execve and the arm_syscall trap handler):
Unhandled exception: IPSR = 00000005 LR = fffffff1
CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216
task: 8b838000 ti: 8b82a000 task.ti: 8b82a000
PC is at flush_thread+0x32/0x40
LR is at flush_thread+0x21/0x40
pc : [<8f00157a>] lr : [<8f001569>] psr: 4100000b
sp : 8b82be20 ip : 00000000 fp : 8b83c000
r10: 00000001 r9 : 88018c84 r8 : 8bb85000
r7 : 8b838000 r6 : 00000000 r5 : 8bb77400 r4 : 8b82a000
r3 : ffff0ff0 r2 : 8b82a000 r1 : 00000000 r0 : 88020354
xPSR: 4100000b
CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216
[<8f002bc1>] (unwind_backtrace) from [<8f002033>] (show_stack+0xb/0xc)
[<8f002033>] (show_stack) from [<8f00265b>] (__invalid_entry+0x4b/0x4c)
As best I can tell this issue existed for the set_tls ARM syscall
before commit fbfb872f5f "ARM: 8148/1: flush TLS and thumbee
register state during exec" consolidated the TLS manipulation code
into the set_tls helper function, but now that we're using it to flush
register state during execve, !MMU users encounter the oops at the
first exec.
Prevent CONFIG_MMU=n configurations from enabling
CONFIG_KUSER_HELPERS.
Fixes: fbfb872f5f (ARM: 8148/1: flush TLS and thumbee register state during exec)
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Reported-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To speed up decompression, the decompressor sets up a flat, cacheable
mapping of memory. However, when there is insufficient space to hold
the page tables for this mapping, we don't bother to enable the caches
and subsequently skip all the cache maintenance hooks.
Skipping the cache maintenance before jumping to the relocated code
allows the processor to predict the branch and populate the I-cache
with stale data before the relocation loop has completed (since a
bootloader may have SCTLR.I set, which permits normal, cacheable
instruction fetches regardless of SCTLR.M).
This patch moves the cache maintenance check into the maintenance
routines themselves, allowing the v6/v7 versions to invalidate the
I-cache regardless of the MMU state.
Cc: <stable@vger.kernel.org>
Reported-by: Marc Carino <marc.ceeeee@gmail.com>
Tested-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
vddio_sdmmc3 is a vdd_io, and thus should be under the vqmmc-supply
property, not vmmc-supply.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This property was wrong and broke eMMC since commit 52221610d ("mmc:
sdhci: Improve external VDD regulator support"). Align the eMMC
properties to those of other Tegra boards.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are general changes pending to make the /aliases/serial* entries
number the serial ports on the system. On Tegra, so far the ports have
been just numbered dynamically as they are configured so that makes them
change.
To avoid this, add specific aliases per board to keep the old numbers.
This allows us to change the numbering by default on future SoCs while
keeping the numbering on existing boards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These labels will be used to provide deterministic numbering of consoles
in a later patch.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
[treding@nvidia.com: drop aliases, reword commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
On sh73a0/kzm9g-legacy, probing of the i2c masters fails with:
i2c-sh_mobile i2c-sh_mobile.0: timing values out of range: L/H=0x208/0x1bf
sh_mobile: probe of i2c-sh_mobile.0 failed with error -22
According to the datasheet, the transfer rate is derived from the HP
clock (which runs at 104 MHz) divided by two. Hence
i2c_sh_mobile_platform_data.clks_per_count should be set to two.
Now probing succeeds, and i2c works:
i2c-sh_mobile i2c-sh_mobile.0: I2C adapter 0 with bus speed 100000 Hz (L/H=0x104/0xe0)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The dma controller requires that the ahb1 bus clock be driven by pll6
for peripheral access to work. Previously this was done in the dma
controller driver, but was since removed as part of a series to unify
the ahb1_mux and ahb1 clock drivers, in
14e0e28 dmaengine: sun6i: Remove obsolete clk muxing code
Unfortunately the rest of that series did not make it, leaving us with
broken dma on sun6i.
This patch reparents ahb1_mux to pll6 using the DT assigned-clocks
properties in the dma controller node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The 5th NAND partition should be named "NAND.u-boot-spl-os"
instead of "NAND.u-boot-spl". This is to be consistent with other
TI boards as well as u-boot.
Fixes: 91994facdd ("ARM: dts: am335x-evm: NAND: update MTD partition table")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The horrible split between the low-level part of the edma support
and the dmaengine front-end driver causes problems on multiplatform
kernels. This is an attempt to improve the situation slightly
by only registering the dmaengine devices that are actually
present.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: add missing include of linux/dma-mapping.h]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Driver has been there since a while back, but the dts never seems to
have been updated with the node (nor pinctrl). Do so now.
Cc: Matt Porter <mporter@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix a regression on Vybrid platform which is caused by commit
dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
driver), and results in a missing configuration on PLL clocks.
- Fix a regression with i.MX defconfig files where CONFIG_SPI option
gets lost accidentally.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUWLLbAAoJEFBXWFqHsHzOCJcH/Rm1q8mIjhHN7Q9k0cYeKuM2
r59Cyl1nJt+nG6qgPK+hPOl3Lw8z9c7zLJ/TG6wsNrAOaFNfNGs3npytL2S6iyDM
KX7IulltuA5Sl5JBXXyMYzn+nm5jBnFrnX/6IUQFI7OB0WVGWOzfyKeqEMzPnG5x
CApc8YHNKe0HBvDyYHkRlNrwwJjVCB2V6H86Km4QsRkTvSkiYa+Fuf1o9M9gpBg9
4wWq9WekFizb0uVTk9tBMcoX82Y/GD6/52MDW2ISGhAVWavxJ2O+UhrdSSmrPqC2
7LY0C6t1YAFZKLn0yn9sAyubG5P/MZF8UAs+7go2s1vtCbG3RvoxPz6RxkEyrmY=
=KnLU
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.18, 2nd round" from Shawn Guo:
"This is the second round of i.MX fixes for 3.18. The clk-vf610 fix is
relatively big, because it needs some adaption to the change made by
offending commit dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits
from clk-pllv3 driver). And it should have been sent to you for earlier
-rc inclusion, but unfortunately it got delayed for some time because
Stefan wasn't aware of my email address change."
The i.MX fixes for 3.18, 2nd round:
- Fix a regression on Vybrid platform which is caused by commit
dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
driver), and results in a missing configuration on PLL clocks.
- Fix a regression with i.MX defconfig files where CONFIG_SPI option
gets lost accidentally.
* tag 'imx-fixes-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (460 commits)
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
+ Linux 3.18-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
Since 64546e9fe3 ("ARM: imx_v6_v7_defconfig updates") and commit
0650f855d2 ("ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM") CONFIG_SPI
selection was dropped by savedefconfig for imx_v4_v5_defconfig and
imx_v6_v7_defconfig.
In order to keep the same behaviour as previous kernel versions and avoid
regressions, let's add CONFIG_SPI option back.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized
by boot loader and the kernel code defined fixed rates according
to those default configurations. Beginning with the USB PLL7 the
code started to initialize the PLL's itself (using imx_clk_pllv3).
However, since commit dc4805c2e7
(ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver)
imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits,
hence the USB PLL were not configured correctly anymore.
This patch not only fixes those USB PLL's, but also makes use of
the imx_clk_pllv3 for all PLL's and alignes the code with the PLL
support of the i.MX6 series.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
produce errors when booted with omap2plus_defconfig, and
reduce bloat by making IPV6 a loadable module.
Also let's add a warning about legacy boot being deprecated
for omap3.
We now have things working with device tree, and only omap3 is
still booting in legacy mode. So hopefully this warning will
help move the remaining legacy mode users to boot with device
tree.
As the total reduction of code and static data is somewhere
around 20000 lines of code once we remove omap3 legacy mode
booting, we really do want to make omap3 to boot also in
device tree mode only over the next few merge cycles.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WvgB
-----END PGP SIGNATURE-----
Merge tag 'fixes-against-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.18-rc2" from Tony Lindgren:
Few fixes for omaps to enable NAND BCH so devices won't
produce errors when booted with omap2plus_defconfig, and
reduce bloat by making IPV6 a loadable module.
Also let's add a warning about legacy boot being deprecated
for omap3.
We now have things working with device tree, and only omap3 is
still booting in legacy mode. So hopefully this warning will
help move the remaining legacy mode users to boot with device
tree.
As the total reduction of code and static data is somewhere
around 20000 lines of code once we remove omap3 legacy mode
booting, we really do want to make omap3 to boot also in
device tree mode only over the next few merge cycles.
* tag 'fixes-against-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (407 commits)
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
+ Linux 3.18-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
The problem is that hardware handled by arm/plat-orion/gpio.c,
require ack for edge irq, and no ack for level irq.
The code handle this issue, by two "struct irq_chip_type" per
one "struct irq_chip_generic". For one "struct irq_chip_generic"
irq_ack pointer is setted, for another it is NULL.
But we have only one mask_cache per two "struct irq_chip_type".
So if we
1)unmask interrupt A for "edge type" trigger,
2)unmask interrupt B for "level type" trigger,
3)unmask interrupt C for "edge type",
we, because of usage of generic irq_gc_mask_clr_bit/irq_gc_mask_set_bit,
have hardware configured to trigger interrupt B on "edge type",
because of shared mask_cache. But kernel think that B is "level type",
so when interrupt B occur via "edge" reason, we don't ack it,
and B triggered again and again.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Link: https://lkml.kernel.org/r/20140726155659.GA22977@fifteen
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A second product has come to light which makes use of the A0 stepping
of the Armada XP SoC. A0 stepping has a hardware bug in the i2c core
meaning that hardware offload does not work, resulting in the kernel
failing to boot. The quirk detects that the kernel is running on an A0
stepping SoC and disables the use of hardware offload.
Currently the quirk is only enabled for PlatHome Openblocks AX3. The
AX3 has been produced with both A0 and B0 stepping SoCs. The second
product is the Lenovo Iomega IX4-300d. It seems likely that this
device will also swap from A0 to B0 SoC sometime during its life.
If there are two products using A0, it seems likely there are more
products with A0. Also, since the number of A0 SoCs is limited, these
products are also likely to transition to B0. Hence detecting at run
time is the safest option. So enable the quirk for all Armada XP
boards.
Tested on an AX3 with A0 stepping.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403ae: ("i2c: mv64xxx: Add I2C Transaction Generator support")
Link: https://lkml.kernel.org/r/1406395238-29758-2-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull networking fixes from David Miller:
"A bit has accumulated, but it's been a week or so since my last batch
of post-merge-window fixes, so...
1) Missing module license in netfilter reject module, from Pablo.
Lots of people ran into this.
2) Off by one in mac80211 baserate calculation, from Karl Beldan.
3) Fix incorrect return value from ax88179_178a driver's set_mac_addr
op, which broke use of it with bonding. From Ian Morgan.
4) Checking of skb_gso_segment()'s return value was not all
encompassing, it can return an SKB pointer, a pointer error, or
NULL. Fix from Florian Westphal.
This is crummy, and longer term will be fixed to just return error
pointers or a real SKB.
6) Encapsulation offloads not being handled by
skb_gso_transport_seglen(). From Florian Westphal.
7) Fix deadlock in TIPC stack, from Ying Xue.
8) Fix performance regression from using rhashtable for netlink
sockets. The problem was the synchronize_net() invoked for every
socket destroy. From Thomas Graf.
9) Fix bug in eBPF verifier, and remove the strong dependency of BPF
on NET. From Alexei Starovoitov.
10) In qdisc_create(), use the correct interface to allocate
->cpu_bstats, otherwise the u64_stats_sync member isn't
initialized properly. From Sabrina Dubroca.
11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter.
12) nf_tables_newchain() was erroneously expecting error pointers from
netdev_alloc_pcpu_stats(). It only returna a valid pointer or
NULL. From Sabrina Dubroca.
13) Fix use-after-free in _decode_session6(), from Li RongQing.
14) When we set the TX flow hash on a socket, we mistakenly do so
before we've nailed down the final source port. Move the setting
deeper to fix this. From Sathya Perla.
15) NAPI budget accounting in amd-xgbe driver was counting descriptors
instead of full packets, fix from Thomas Lendacky.
16) Fix total_data_buflen calculation in hyperv driver, from Haiyang
Zhang.
17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke
Mehrtens.
18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is
that something that ends up being vmalloc memory can't be passed
to the crypto hash routines via scatter-gather lists. From Eric
Dumazet.
19) Fix regression in promiscuous mode enabling in cdc-ether, from
Olivier Blin.
20) Bucket eviction and frag entry killing can race with eachother,
causing an unlink of the object from the wrong list. Fix from
Nikolay Aleksandrov.
21) Missing initialization of spinlock in cxgb4 driver, from Anish
Bhatt.
22) Do not cache ipv4 routing failures, otherwise if the sysctl for
forwarding is subsequently enabled this won't be seen. From
Nicolas Cavallari"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits)
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
drivers: net: cpsw: Fix broken loop condition in switch mode
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
stmmac: pci: set default of the filter bins
net: smc91x: Fix gpios for device tree based booting
mpls: Allow mpls_gso to be built as module
mpls: Fix mpls_gso handler.
r8152: stop submitting intr for -EPROTO
netfilter: nft_reject_bridge: restrict reject to prerouting and input
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing
drivers/net: macvtap and tun depend on INET
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
drivers/net: Disable UFO through virtio
net: skb_fclone_busy() needs to detect orphaned skb
gre: Use inner mac length when computing tunnel length
mlx4: Avoid leaking steering rules on flow creation error flow
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
...
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're moving omaps to use device tree based booting and already have
omap2, omap4, omap5, am335x and am437x booting in device tree only
mode.
Only omap3 still has legacy booting still around and we really want
to make that device tree only. So let's add a warning about deprecated
legacy booting so we get people to upgrade their boards to use device
tree based booting and find out about any remaining issues.
Note that for most boards we already have the .dts file and those can
be booted with without changing the bootloader using the appended
DTB mode.
Acked-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we need to have BCH enabled to get NAND
working and to avoid getting:
nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since CONFIG_HIGHMEM got enabled on ARMv5 Kirkwood, we have noticed a
very significant drop in networking performance. The test were
conducted on an OpenBlocks A7 board. Without this patch, the outgoing
performance measured with iperf are:
- highmem OFF, TSO OFF 544 Mbit/s
- highmem OFF, TSO ON 942 Mbit/s
- highmem ON, TSO OFF 306 Mbit/s
- highmem ON, TSO ON 246 Mbit/s
On this Kirkwood platform, the L2 cache is a Feroceon cache, and with
this cache, all the range operations have to be done on virtual
addresses and not physical addresses. Therefore, whenever
CONFIG_HIGHMEM is enabled, the cache maintenance operations call
kmap_atomic_pfn() and kunmap_atomic().
However, kmap_atomic_pfn() does not implement the same fast path for
non-highmem pages as the one implemented in kmap_atomic(), and this is
one of the reason for the performance drop. While this patch does not
fully restore the performances, it clearly improves them a lot:
without patch with patch
- highmem ON, TSO OFF 306 Mbit/s 387 Mbit/s
- highmem ON, TSO ON 246 Mbit/s 434 Mbit/s
We're still far from the !CONFIG_HIGHMEM performances, but it does
improve a bit the situation.
Thanks a lot to Ezequiel Garcia and Gregory Clement for all the
testing work around this topic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King suggested [1]:
"I'd ask for one change. Please make all these messages start with
"L2C-310 OF" not "PL310 OF:". The device is described in ARM
documentation as a L2C-310 not PL310. (Also note the : is dropped
too - most of the other messages don't have the : either.)
The:
"PL310 OF: cache setting yield illegal associativity
PL310 OF: -1073346556 calculated, only 8 and 16 legal"
message could also be changed to something like:
"L2C-310 OF cache associativity %d invalid, only 8 or 16 permittedn"
[1] http://www.spinics.net/lists/arm-kernel/msg372776.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 513510ddba
(common: dma-mapping: introduce common remapping functions)
managed to end up with an extra return statement from the
original patch. Drop it.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit f3354ab674 ("ARM: 8169/1: l2c: parse cache properties from
ePAPR definitions") the following error is seen on imx6q:
[ 0.000000] PL310 OF: cache setting yield illegal associativity
[ 0.000000] PL310 OF: -2147097556 calculated, only 8 and 16 legal
As imx6q does not pass the "cache-size" and "cache-sets" properties in DT, the function l2x0_cache_size_of_parse() returns early and keep the 'associativity' pointer uninitialized.
To fix this problem, return error codes inside l2x0_cache_size_of_parse() and only use the 'associativity' pointer result if l2x0_cache_size_of_parse() succeeds.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables configs required to boot IFC6540 board with atleast a
serial console.
Without this patch there is no serial console.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When arch/arm/mach-ixp4xx/common-pci.c is compiled, two warnings
occur:
arch/arm/mach-ixp4xx/include/mach/io.h:144: warning: passing argument 1 of '__raw_readb' makes pointer from integer without a cast
arch/arm/mach-ixp4xx/include/mach/io.h:79: warning: passing argument 2 of '__raw_writeb' makes pointer from integer without a cast
Both functions expect an 'volatile void __iomem *' but get an u32.
The 'u32 addr' variable is initialized with the address of an
'volatile void __iomem *' pointer. Passing the pointer
directly, avoids the warning and semantics are preserved.
This warning was found with vampyr.
Signed-off-by: Stefan Hengelein <stefan.hengelein@fau.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull ARM fixes from Russell King:
"A couple of ARM fixes.
We fix some printk formats for ptrdiff_t quantities which cause GCC
4.9 to complain, and we also blacklist known buggy GCC 4.8.x compilers
as their miscompilation is serious enough to cause filesystem
corruption, even through many distros have fixed their versions"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix some printk formats
ARM: Blacklist GCC 4.8.0 to GCC 4.8.2 - PR58854
Tyler Baker