The arrays are never modified, make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On non-DT platforms IRQ controllers associated with the GPIOs have a
fixed IRQ base value known at compile time. The sh-pfc driver translates
GPIO number to IRQ numbers using a hardcoded table. This mechanism
breaks on DT platforms, as the IRQ base values are dynamic in that case.
Fix this by specifying IRQs associated with GPIOs in IRQ resources,
populated automatically from the device tree. When IRQ resources are
specified the driver requires one IRQ resource per GPIO able to generate
an interrupt, and uses the translation table to compute the IRQ resource
offset instead of the IRQ number.
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's more than one window, name the field windows.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
0 is a valid GPIO value, use -1 to terminate the gpios array in IRQ
lists.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some indices take positive values only, make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pins with selectable functions but without a GPIO port can't be named
PORT_# or GP_#_#. Add a SH_PFC_PIN_NAMED macro to declare such pins in
the pinmux pins array, naming them with the PIN_ prefix followed by the
pin physical position.
In order to make sure not to register those pins as GPIOs, add a
SH_PFC_PIN_CFG_NO_GPIO pin flag to denote pins without a GPIO port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Remove the manually specified ranges from PFC SoC data and compute the
ranges automatically. This prevents ranges from being out-of-sync with
pins definitions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The field contains the number of pins with an associated GPIO port. This
is currently equal to the total number of pins but will be modified when
adding support for pins without a GPIO port. Rename the field
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The gpio_get_data_reg() and gpio_setup_data_reg() functions both take an
argument named gpio. The argument contains a GPIO offset for the first
function and a pin index for the second one. Rename them to offset and
idx respectively to match the rest of the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The GPIO driver uses an array of sh_pfc_gpio_pin structures to store
per-GPIO pin data. The array size is miscomputed at allocation time by
using the number of the last pin instead of the number of pins. When the
pin space contains holes this leads to memory overallocation. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Boards/platforms that register dedicated GPIO devices will not supply a
memory resource for GPIOs. Try to locate the GPIO memory resource at
initialization time, and skip registration of the gpiochip if the
resource can't be found.
This is a temporary modification to ease the transition to separate GPIO
drivers. It should be reverted when all boards and platforms will have
been moved.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When implemented as a separate IP block, GPIOs should be handled by a
separate driver. To make this possible GPIO support needs to be optional
in the sh-pfc driver.
If no GPIO data registers are supplied in the SoC information structure
skip registration of the gpiochip.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The target is to get rid of function GPIOs completely. To reach this,
make function GPIOs support optional by skipping the function GPIO chip
registration if no function GPIOS are defined in SoC data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
None of the SoC data need to be modified. Constify it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The purpose of the dry-run is to ensure that a pin about to be
configured isn't in use. However, the current implementation is a no-op.
This proves that the dry-run isn't essential. Remove it.
Freeing configuration then becomes a no-op as well. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The sh_pfc_pin structure supplied in SoC data contains information about
pin configuration and name. It's abused to store GPIO data registers
information and pin config type. Move those fields out of the
pinmux_data_reg structure into the new sh_pfc_gpio_pin and
sh_pfc_pin_config structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux_data_reg structure supplied in SoC data contains information
about data registers. It's abused to store per-device mapped iomem and
shadow values. Move those fields out of the pinmux_data_reg structure
into the per-device sh_pfc_chip structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All data registers are located in the same memory resource. Locate the
mapped resource at initializat time and use it directly instead of
computing a mapped address for each register. This gets rid of the
mapped_reg field of the pinmux_data_reg structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Move the sh_pfc_setup_data_regs(), sh_pfc_setup_data_reg(),
sh_pfc_get_data_reg(), sh_pfc_read_bit() and sh_pfc_write_bit()
function to gpio.c as they belong to the GPIO implementation. Inline
sh_pfc_read_bit() and sh_pfc_write_bit() in their only call location.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC driver assumes that the value of the GPIO_PORTxxx enumeration
names are equal to the port number. This isn't true when the port number
space is sparse, as with the SH73A0.
Fix the issue by adding support for pin numbers ranges specified through
SoC data. When no range is specified the driver considers that the PFC
implements a single contiguous range for all pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Adding a GPIO range to a pinctrl device logically belongs to the GPIO
driver. Switch to the right API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This prepares support for sparse pin numbering. The function currently
just performs and indexed lookup in the pins array.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The function is guaranteed to be called with a gpio number smaller than
nr_pins. The condition can the be simplified, and the function inlined.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The PFC core exposes a sh_pfc_config_gpio() function that configures
pinmuxing for a given GPIO (either a real GPIO or a function GPIO).
Handling of real and function GPIOs belong to the GPIO layer, move the
GPIO number to mark translation to the caller and rename the function to
sh_pfc_config_mux().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Instead of converting the GPIO number to an enum_id and looking up IRQ
table entries by enum_id, replace the pinmux_irq enum_ids field with a
gpios field and lookup entries using the GPIO number.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Register two GPIO chips, one for the real GPIOs and one for the function
GPIOs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Split the GPIOs table into a pins table for real GPIOs and a functions
table for function GPIOs.
Only register pins with the pinctrl core. The function GPIOs remain
accessible as GPIOs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO type is always PINMUX_TYPE_FUNCTION when freeing a function
GPIO. Hardcode the type value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
As a step towards GPIO function removal, shorten the GPIO range
registered with the pinctrl core. Function GPIOs are now handled in the
GPIO handlers directly instead of going through the pinctrl API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The SoC information first_gpio field is always equal to 0, and the
last_gpio field is the index of the last entry in the pinmux_gpios
array. Replace the first_gpio and last_gpio fields by a nr_gpios field,
and initialize it to ARRAY_SIZE(pinmux_gpios).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The header file isn't used by arch code anymore. Make it private to the
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pinmux information should be provided by the pinmux driver, not arch
code. Make it possible to do so by supporting pinmux information passed
through the driver_data field in the platform ID table. Platform data
will remain supported until all arch code has been converted.
Rename the sh_pfc_platform_data structure to sh_pfc_soc_info to reflect
this.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
