The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are VIN2 and VIN3 channels available on the R8A7790 SoC.
VIN2 supports 4/8/16/18/24-bit data, while VIN3 supports 8-bit.
Add both here, covering all possible data pin configurations.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Both VIN0 and VIN1 channels support identical input interfaces.
Add missing VIN1 pins here and organize them in the same pin
groups as VIN0.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This reorganizes and renames VIN0 data pin groups to cover
all possible configurations. There's total of eight data
pin groups, one per each configuration. Most of the groups
share the same pin/mux array. Only the 18-bit configuration
needs a separate pin/mux array since in combines interleaved
data pins.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This groups VIN0 HSYNC and VSYNC pins together
since one cannot be used without another.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This drops superfluous "signal" word from the pin group names
and renames data_enable group to clkenb as in the h/w manual.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
There are four I2C interfaces on r8a7790, each of them can be connected to
one of the two respective I2C controllers, e.g. interface #0 can be
configured to work with I2C0 or with IIC0. Additionally some of those
interfaces can also use one of several pin sets. Interface #3 is special,
because it can be used in automatic mode for DVFS. It only has one set
of pins available and those pins cannot be used for anything else, they
also lack the GPIO function.
This patch uses the sh-pfc ability to configure pins, not associated with
GPIOs and adds support for I2C3 to the r8a7790 PFC set up.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Adds pinmux for i2c bus 1 and 2. (Pins for 0 and 3 are not multiplexed.)
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Name the DU clock input 1 consistently with clock inputs 0 and 2.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Navigating through the source code is hard enough without having to
manually search for groups and functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Update the pinmux configuration tables to support the TCLK1 pin.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The SCIFA2 RXD_B and HRX0_C pins have their pinmux configuration data
swapped, fix it.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The pins have been removed from the datasheet, remove them here as well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The pins have been removed from the datasheet, remove them here as well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The pins have been removed from the datasheet, remove them here as well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The RTS/CTS pins have been renamed in the datasheet, rename them here as
well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The I2C pins have been renamed in the datasheet, rename them here as
well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Move macros defined in several SoC data files to a common location and
document them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The typedef only conceals the real variable type without bringing any
additional value (see Documentation/CodingStyle, section 5.b). Moreover,
it polutes the pinmux namespace. Replace it with the integer type it
used to hide.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
This patch adds pinmux groups and functions for the two MMCIF and four
SDHI interfaces on r8a73a4 (APE6).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix several errors in Peripheral Function Select register tables for
r8a7790, which prevent various function pins from being correctly
configured.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Refactor the GPIO macro magic to use GPIO numbers directly instead of
the GPIO_GP_x_y enum entries. This will allow removing the GPIO enum
entries from the mach/r8a7790.h header.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No r8a7770 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: fixed typo in changelog: r8a7779 -> r8a7770]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
GPIOs are now handled by a separate driver, remove GPIO data from the
SoC information structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial PFC support for the r8a7790 SoC.
At this point only GPIO interface is supported, move to
newer interfaces planned as incremental changes.
Original authors is Koji Matsuoka-san, thanks for him
and his team for the heavy lifting. Adjusted by Magnus
to work together with updated code in drivers/pinctrl.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@rms.renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
