Some devices have more than just simple TX and RX DMA channels, for example
modern Samsung I2S IPs support a secondary transmit DMA stream which is
mixed into the primary stream during playback. Allow such devices to
specify the names of the channels to be requested in their dma_data.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Now it's quite common that an SoC contains its on-chip internal RAM.
By using this RAM space for DMA buffer during audio playback/record,
we can shutdown the voltage for external RAM to save power.
So add new DEV type with iram malloc()/free() and accordingly modify
current default mmap() for the iram circumstance.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current SSI needs RSND_SSI_DEPENDENT flag to
decide dependent/independent mode.
And SCU needs RSND_SCU_USE_HPBIF flag
to decide HPBIF is enable/disable.
But these 2 means same things.
This patch adds new rsnd_scu_hpbif_is_enable()
function, and merges above methods.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allow DMA data to be set at probe time for devices that can do that,
avoiding the need to do it every time we start a stream and supporting
non-DT dmaengine users using the helpers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently each platform making use the the generic dmaengine PCM driver still
needs to provide a custom snd_pcm_hardware struct which specifies the
capabilities of the DMA controller, e.g. the maximum period size that can be
supported. This patch adds code which uses the newly introduced
dma_get_slave_caps() API to query this information from the dmaengine driver.
The new code path will only be taken if the 'pcm_hardware' field of the
snd_dmaengine_pcm_config struct is NULL.
The patch also introduces a new 'fifo_size' field to the
snd_dmaengine_dai_dma_data struct which is used to initialize the
snd_pcm_hardware 'fifo_size' field and needs to be set by the DAI driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current snd_soc_of_get_dai_name() needs .of_xlate_dai_name()
callback on each component drivers.
But required behavior on almost all these drivers is
just returns its indexed driver's name.
This patch adds this feature as default behavior.
.of_xlate_dai_name() can overwrite it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for RST GPIO and Charge Pump Freq in platform data
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a comment to the trigger function in snd_soc_dai_ops struct about
possible command sequences.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rcar is using rsnd_is_gen1/gen2() to checking its
IP generation, but it needs data mask.
This patch fixes it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for virtual DAPM mixer controls. They are similar to
virtual DAPM enums. There is no hardware register backing the control, so
changing the control's value wont have any direct effect on the hardware. But it
still influences the DAPM graph by causing the path it sits on to be connected
or disconnected. This in turn can cause power changes for some of the widgets on
the DAPM graph, which will then modify the hardware state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ASoC sound driver requires CPU/CODEC drivers for probing,
and each CPU/CODEC has some DAI on it.
Then, "dai name matching" have been used to identify
CPU-CODEC DAI pair on ASoC.
But, the "dai port number matching" is now required from DeviceTree.
The solution of this issue is to replace
the dai port number into dai name.
Now, CPU/CODEC are based on struct snd_soc_component,
and it can care above as common issue.
This patch adds .of_xlate_dai_name callback interface
on struct snd_soc_component_driver,
and snd_soc_of_get_dai_name() which is using .of_xlate_dai_name.
Then, #sound-dai-cells which enables DAI specifier is required
on CPU/CODEC device tree properties.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Codec includes component by this patch,
and component moved to upside of codec
to avoid extra declaration.
Codec dai will be registered via component
by this patch.
Current component register function
is used for cpu, and it is using
dai/dais functions properly to keep
existing cpu dai name.
And now, it will be used from codec also.
But codec driver had been used dais function only
even though it was single dai.
This patch adds new flag which can selects
dai/dais function on component register
function to keep existing codec dai name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some codec drivers when running in slave mode require that BCLK to sample rate ratio
is explicitly set by the machine driver as it may not be exactly rate * frame size.
Extend the DAI API by adding :-
int snd_soc_dai_set_bclk_ratio(struct snd_soc_dai *dai, unsigned int ratio);
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify error handling and remove repetitive (and rarely executed) code
for unregistration by providing a devm_snd_soc_register() card.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Since with the wider use of devres many drivers are now only calling
snd_soc_unregister_component() in their remove functions providing a
managed version will save a reasonable amount of code.
Signed-off-by: Mark Brown <broonie@linaro.org>
The only cache type left is the flat cache and new other cache types won't be
added since new drivers are supposed to use regmap directly for IO and caching.
This patch removes the snd_soc_cache_ops indirection that was added to support
multiple cache types and modifies the code to always use the flat cache
directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The reg_size field is calculated in snd_soc_register_codec() and then used
exactly once in snd_soc_flat_cache_init(). Since it is calculated based on other
fields from the codec struct just move the calculation to
snd_soc_flat_cache_init() and remove the 'reg_size' field from the codec struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
reg_def_copy was introduced in commit 3335ddca ("ASoC: soc-cache: Use
reg_def_copy instead of reg_cache_default") to keep a copy of the register
defaults around in case the register defaults where placed in the __devinitdata
section. With the __devinitdata section gone we effectivly keep the same data
around twice. This patch removes reg_def_copy and uses reg_cache_default
directly instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
No users of snd_soc_bulk_write_raw() are left and new drivers are going to use
regmap directly for this, so the function can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
No users of reg_access_defaults are left and new drivers are going to use regmap
for this, so support for it can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull media updates from Mauro Carvalho Chehab:
"This series contains:
- Exynos s5p-mfc driver got support for VP8 encoder
- Some SoC drivers gained support for asynchronous registration
(needed for DT)
- The RC subsystem gained support for RC activity LED;
- New drivers added: a video decoder(adv7842), a video encoder
(adv7511), a new GSPCA driver (stk1135) and support for Renesas
R-Car (vsp1)
- the first SDR kernel driver: mirics msi3101. Due to some troubles
with the driver, and because the API is still under discussion, it
will be merged at staging for 3.12. Need to rework on it
- usual new boards additions, fixes, cleanups and driver
improvements"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (242 commits)
[media] cx88: Fix regression: CX88_AUDIO_WM8775 can't be 0
[media] exynos4-is: Fix entity unregistration on error path
[media] exynos-gsc: Register v4l2 device
[media] exynos4-is: Fix fimc-lite bayer formats
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
[media] v4l: vsp1: Fix mutex double lock at streamon time
[media] v4l: vsp1: Add support for RT clock
[media] v4l: vsp1: Initialize media device bus_info field
[media] davinci: vpif_capture: fix error return code in vpif_probe()
[media] davinci: vpif_display: fix error return code in vpif_probe()
[media] MAINTAINERS: add entries for adv7511 and adv7842
...
Add 'playback_only' and 'capture_only' fields that can be used for specifying
that a dai_link has a unidirectional capability.
The motivation for this is for the cases of systems, such as Freescale MX28,
that has two unidirectional DAIs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The sysfs_registered field was added to the snd_soc_codec struct in commit
f0fba2ad ("ASoC: multi-component - ASoC Multi-Component Support"), but has never
been used.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DAPM context struct has its own field where it stores the pointer to the
DAPM debugfs entry. The debugfs_dapm field in the snd_soc_platform and
snd_soc_codec structs are completely unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The control_type field was used by the core to track which raw IO methods to
use, but when switching to regmap this was no longer necessary and so the last
user of the field was removed in commit be3ea3b9 ("ASoC: Use new register map
API for ASoC generic physical I/O"). The field is now completely unused and can
be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_dapm_new_widgets() works on the ASoC card as a whole not on a specific
DAPM context. The DAPM context that is passed as the parameter is only used to
look up the pointer to the card. This patch updates the signature of
snd_soc_dapm_new_widgets() to take the card directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=qzif
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.12
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
This patch adds generic ac97 reset functions using pincontrol and gpio
parsed from devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Direct calls to printk_limit() will emit log noise even when CONFIG_SND_DEBUG is not
defined. Add a wrapper macro around printk_limit() that is conditionally defined by
CONFIG_SND_DEBUG.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Yacine Belkadi <yacine.belkadi.1@gmail.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move include/sound/tea575x-tuner.h to include/media/tea575x.h and update files that include it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use snd_dmaengine_dai_dma_data for passing the dma parameters from
clients to the pxa pcm lib. This does no functional change, it's just an
intermedia step to migrate the pxa bits over to dmaengine.
The calculation of dcmd is a transition hack which will be removed again
in a later patch. It's just there to make the transition more readable.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_info_enum_ext() and snd_soc_info_enum_double() are almost identical. The
only difference is that snd_soc_info_enum_double() is also able to handle stereo
controls. Using snd_soc_info_enum double() instead of snd_soc_info_enum_ext()
for the SOC_ENUM_EXT control's info callback allows us to remove
snd_soc_info_enum_ext().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SOC_SINGLE_EXT control has been using snd_soc_info_volsw() for its info
callback since commit 1c433fb ("[ALSA] soc - 0.13 ASoC headers"). The
snd_soc_info_volsw_ext() function has been unused ever since then, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds BUSIF support for R-Car sound DMAEngine transfer.
The sound data will be transferred via FIFO which can cover blank time
which will happen when DMA channel is switching.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds DMAEngine transfer on SSI.
But, it transfers sound data from memory to SSI directly
without using HPBIF at this time.
It will be updated soon
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rsnd driver is using struct rsnd_dai_platform_info
so that indicate sound DAI information (playback/capture SSI ID).
But, SSI settings were also required separately.
Thus, platform settings was very un-understandable.
This patch adds dai_id to SSI
settings, and removed rsnd_dai_platform_info.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some devices have the problem that if a internal audio signal source is disabled
the output of the source becomes undefined or goes to a undesired state (E.g.
DAC output goes to ground instead of VMID). In this case it is necessary, in
order to avoid unwanted clicks and pops, to disable any mixer input the signal
feeds into or to active a mute control along the path to the output. Often it is
still desirable to expose the same mixer input control to userspace, so cerain
paths can sill be disabled manually. This means we can not use conventional DAPM
to manage the mixer input control. This patch implements a method for letting
DAPM overwrite the state of a userspace visible control. I.e. DAPM will disable
the control if the path on which the control sits becomes inactive. Userspace
will then only see a cached copy of the controls state. Once DAPM powers the
path up again it will sync the userspace setting with the hardware and give
control back to userspace.
To implement this a new widget type is introduced. One widget of this type will
be created for each DAPM kcontrol which has the auto-disable feature enabled.
For each path that is controlled by the kcontrol the widget will be connected to
the source of that path. The new widget type behaves like a supply widget,
which means it will power up if one of its sinks are powered up and will only
power down if all of its sinks are powered down. In order to only have the mixer
input enabled when the source signal is valid the new widget type will be
disabled before all other widget types and only be enabled after all other
widget types.
E.g. consider the following simplified example. A DAC is connected to a mixer
and the mixer has a control to enable or disable the signal from the DAC.
+-------+
+-----+ | |
| DAC |-----[Ctrl]-| Mixer |
+-----+ : | |
| : +-------+
| :
+-------------+
| Ctrl widget |
+-------------+
If the control has the auto-disable feature enabled we'll create a widget for
the control. This widget is connected to the DAC as it is the source for the
mixer input. If the DAC powers up the control widget powers up and if the DAC
powers down the control widget is powered down. As long as the control widget
is powered down the hardware input control is kept disabled and if it is enabled
userspace can freely change the control's state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the DAPM code is limited to only setting or clearing a single bit in a
register to power a widget up or down. This patch extends the DAPM code to be
more flexible in that regard and allow widgets to use arbitrary values to be
used to put a widget in either on or off state.
Since the snd_soc_dapm_widget struct already contains a on_val and off_val field
no additional fields need to be added and in fact the invert field can even be
removed. Also the generated code is slightly smaller.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently we store for each path which control (if any at all) is associated
with that control. But we are only ever interested in the reverse relationship,
i.e. we want to know all the paths a certain control is associated with. This is
currently implemented by always iterating over all paths. This patch updates the
code to keep a list for each control which contains all the paths that are
associated with that control. This improves the run time of e.g.
soc_dapm_mixer_update_power() and soc_dapm_mux_update_power() from O(n) (with n
being the number of paths for the card) to O(1).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 'value' field is really per control and not per widget. Currently it is only
used for virtual MUXes, which only have one control per widget. So in that case
there is not so much of a difference between whether it is stored per widget or
per control. Moving the 'value' field from the widget to the control will allow
us to use it also for cases where we have more than one control per widget. E.g.
for mixers with multiple input controls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We use the same 3 lines to get the CODEC for a kcontrol in a quite a few places.
This patch puts them into a common helper function. Having this encapsulated in
a helper function will also make it more easier to eventually change the data
layout of the kcontrol's private data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The update field of a DAPM context is only assigned while the card's dapm_mutex
is locked, the field is also cleared again while the mutex is stil locked. So
there will only ever be one DAPM context at a time with a non-NULL update field.
So it is safe to move the update field from the DAPM context struct to the card
struct. Doing so will allow further cleanups in this area.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is useful for drivers who want to grab a pointer to
snd_kcontrol outside of the kcontrol callbacks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
As 1st protype, this patch adds SSI feature on this driver.
But, it is PIO sound playback support only at this point.
The DMA transfer, and capture feature will be supported in the future
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
This patch adds ADG feature which controls sound clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
This patch adds SCU feature on this driver.
But, it defines SCU style only, does nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
The main difference between Gen1 and Gen2 are
1) register offset, 2) data path
In order to control Gen1/Gen2 by same method,
this patch adds gen.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuits are different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2).
(Actually, there are many difference in Generation1 chips)
Basically, for the future, Renesas R-Car series will use
Gen2 style sound circuit, but driver should care Gen1 also.
The main differences between Gen1 and Gen2 peripheral
are 1) register offset, 2) data path.
This patch adds basic (core) feature for R-Car
series sound driver as prototype
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move HW initialization to separate function to allow using the code without
the v4l parts. This is needed for use in the bttv driver.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to avoid race conditions the assignment of dapm->update should happen
while card->dapm_mutex is being held. To allow CODEC drivers to run a register
update when using snd_soc_dapm_mux_update_power() or
snd_soc_dapm_mixer_update_power() add a update parameter to these two functions.
The update parameter will be assigned to dapm->update while card->dapm_mutex is
locked.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when updating a control that is shared between multiple widgets the
whole power-up/power-down sequence is being run once for each widget. The
control register is updated during the first run, which means the CODEC internal
routing is also updated for all widgets during this first run. The input and
output paths for each widgets are only updated though during the respective run
for that widget. This leads to a slight inconsistency between the CODEC's
internal state and ASoC's state, which causes non optimal behavior in regard to
click and pop avoidance.
E.g. consider the following setup where two MUXs share the same control.
+------+
A1 ------| |
| MUX1 |----- C1
B1 ------| |
+------+
|
control ---+
|
+------+
A2 ------| |
| MUX2 |----- C2
B2 ------| |
+------+
If the control is updated to switch the MUXs from input A to input B with the
current code the power-up/power-down sequence will look like this:
Run soc_dapm_mux_update_power for MUX1
Power-down A1
Update MUXing
Power-up B1
Run soc_dapm_mux_update_power for MUX2
Power-down A2
(Update MUXing)
Power-up B2
Note that the second 'Update Muxing' is a no-op, since the register was already
updated.
While the preferred order for avoiding pops and clicks should be:
Run soc_dapm_mux_update_power for control
Power-down A1
Power-down A2
Update MUXing
Power-up B1
Power-up B2
This patch changes the behavior to the later by running the updates for all
widgets that the control is attached to at the same time.
The new code is also a bit simpler since callers of
soc_dapm_{mux,muxer}_update_power don't have to loop over each widget anymore
and neither do we need to keep track for which of the kcontrol's widgets the
current update is.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
soc_dpcm_runtime_update() operates on a ASoC card as a whole. Currently it takes
a snd_soc_dapm_widget as its only parameter though. The widget is then used to
look up the card and is otherwise unused. This patch changes the function to
take a pointer to the card directly. This makes it possible to to call
soc_dpcm_runtime_update() for updates which are not related to one specific
widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some more fixes and enhancements, and also a bunch of refectoring for
AC'97 support which enables more than one AC'97 controller driver to be
built in.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UZaY
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.11
Some more fixes and enhancements, and also a bunch of refectoring for
AC'97 support which enables more than one AC'97 controller driver to be
built in.
Currently we can only have a single platform built in with AC'97 support
due to the use of a global variable to provide the bus operations. Fix
this by making that variable a pointer and having the bus drivers set the
operations prior to registering.
This is not a particularly good or nice approach but it avoids blocking
multiplatform and a real fix involves fixing the fairly deep problems
with AC'97 support - we should be converting it to a real bus.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce a new helper function, snd_ctl_sync_vmaster(), which updates
the slave put callbacks forcibly as well as calling the hook. This
will be used in the upcoming patch in HD-audio codec driver for
toggling the mute in vmaster slaves.
Along with the new function, the old snd_ctl_sync_vmaster_hook() is
replaced as a macro calling with the argument hook_only=true.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not a big release subsystem wise, the main changes have been some nice
improvements on the driver side:
- Lots of cleanups and fixes for Blackfin, SGTL5000 and UX500.
- Generalisation of the Bluetooth and HDMI stub drivers.
- New CODEC drivers for SSM2518 and RT5640.
- New machine driver for Tegra CPUs with RT5640.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gWf9
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.11
Not a big release subsystem wise, the main changes have been some nice
improvements on the driver side:
- Lots of cleanups and fixes for Blackfin, SGTL5000 and UX500.
- Generalisation of the Bluetooth and HDMI stub drivers.
- New CODEC drivers for SSM2518 and RT5640.
- New machine driver for Tegra CPUs with RT5640.
* for-linus: (635 commits)
ALSA: usb-audio: Fix invalid volume resolution for Logitech HD Webcam c310
ALSA: hda - Fix pin configurations for MacBook Air 4,2
ALSA: usb-audio: work around Android accessory firmware bug
ALSA: hda - Headset mic support for three more machines
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
...
Since commit 85762e71 ("ASoC: dapm: Implement mixer control sharing") the
long_name field of the snd_soc_dapm_path struct is unused. All of the name
handling now happens entirely in dapm_create_or_share_mixmux_kcontrol(). So we
can remove the long_name field from the snd_soc_dapm_path struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the ALC5640 codec driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Even though they are virtual widgets DAI widgets still get counted for the
DAPM context power management so we can't just use the active state to
check if they should be powered as they may not be part of a complete path.
Instead split them into input and output widgets and do the same power
checks as we perform on AIFs.
Reported-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently ALSA supports up to 32 card instances when the dynamic minor
is used. While 32 cards are usually big enough for normal use cases,
there are sometimes weird requirements with more card support.
Actually, this limitation, 32, comes from the index option, where you
can pass the bit mask to assign the card. Other than that, we can
actually give more cards up to the minor number limits (currently 256,
which can be extended more, too).
This patch adds a new Kconfig to specify the max card numbers, and
changes a few places to accept more than 32 cards.
The only incompatibility with high card numbers would be the handling
of index option. The index option can be still used to pass the
bitmask for card assignments, but this works only up to 32 slots.
More than 32, no bitmask style option is available but only a single
slot can be specified via index option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ops field of the snd_pcm_substream struct is never modified inside the ALSA
core. Making it const allows drivers to declare their snd_pcm_ops struct as
const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices may benefit from being able to start some parts of the widget
power up/down sequence earlier on in the sequence than the point at which
the final power state is committed. Support these by providing events which
are called before any power state changes are done.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
This contains small fixes since the previous pull request:
- A few regression fixes and small updates of HD-audio
- Yet another fix for Haswell HDMI audio
- A copule of trivial fixes in ASoC McASP, DPAM and WM8994
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=DMsb
-----END PGP SIGNATURE-----
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains small fixes since the previous pull request:
- A few regression fixes and small updates of HD-audio
- Yet another fix for Haswell HDMI audio
- A copule of trivial fixes in ASoC McASP, DPAM and WM8994"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: hda - Don't set up active streams twice"
ALSA: Add comment for control TLV API
ALSA: hda - Apply pin-enablement workaround to all Haswell HDMI codecs
ALSA: HDA: Fix Oops caused by dereference NULL pointer
ALSA: mips/sgio2audio: Remove redundant platform_set_drvdata()
ALSA: mips/hal2: Remove redundant platform_set_drvdata()
ALSA: hda - Fix 3.9 regression of EAPD init on Conexant codecs
sound: Fix make allmodconfig on MIPS
ALSA: hda - Fix system panic when DMA > 40 bits for Nvidia audio controllers
ALSA: atmel: Remove redundant platform_set_drvdata()
ASoC: McASP: Fix receive clock polarity in DAIFMT_NB_NF mode.
ASoC: wm8994: missing break in wm8994_aif3_hw_params()
ASoC: McASP: Add pins output direction for rx clocks when configured in CBS_CFS format
ASoC: dapm: use clk_prepare_enable and clk_disable_unprepare
Userspace is not meant to have to handle all strange dB ranges,
so add a specification comment.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone mic
and headset mic support, jack_modes hint consolidation, proper beep
attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=sYiI
-----END PGP SIGNATURE-----
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone
mic and headset mic support, jack_modes hint consolidation, proper
beep attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (315 commits)
ALSA: usb-audio: caiaq: fix endianness bug in snd_usb_caiaq_maschine_dispatch
ALSA: asihpi: add format support check in snd_card_asihpi_capture_formats
ALSA: pcm_format_to_bits strong-typed conversion
ALSA: compress: fix the states to check for allowing read
ALSA: hda - Move Thinkpad X220 to use auto parser
ALSA: USB: adjust for changed 3.8 USB API
ALSA: usb - Avoid unnecessary sample rate changes on USB 2.0 clock sources
sound: oss/dmabuf: use dma_map_single
ALSA: ali5451: use mdelay instead of large udelay constants
ALSA: hda - Add the support for ALC286 codec
ALSA: usb-audio: USB quirk for Yamaha THR10C
ALSA: usb-audio: USB quirk for Yamaha THR5A
ALSA: usb-audio: USB quirk for Yamaha THR10
ALSA: usb-audio: Fix autopm error during probing
ALSA: snd-usb: try harder to find USB_DT_CS_ENDPOINT
ALSA: sound kconfig typo
ALSA: emu10k1: Fix dock firmware loading
ASoC: ux500: forward declare msp_i2s_platform_data
ASoC: davinci-mcasp: Add Support BCLK-to-LRCLK ratio for TDM modes
ASoC: davinci-pcm, davinci-mcasp: Clean up active_serializers
...
Add a function to handle conversion from snd_pcm_format_t
to bitwise with proper typing.
Change such conversions to use this function and silence sparse
warnings.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few more fixes, nothing too major though the DMA changes fix modular
builds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CgWu
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.10
A few more fixes, nothing too major though the DMA changes fix modular
builds.
Fix typo in printk and comments within various drivers.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit [b209c4df: ALSA: emu10k1: cache emu1010 firmware] broke the
firmware loading of the dock, just (mistakenly) ignoring a different
firmware for docks on some models. This patch revives them again.
Bugzilla: https://bugs.archlinux.org/task/34865
Reported-and-tested-by: Tobias Powalowski <tobias.powalowski@googlemail.com>
Cc: <stable@vger.kernel.org> [v3.8+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some platforms which are half-duplex share the same DMA channel between the
playback and capture stream. Add support for this to the generic dmaengine PCM
driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch reworks the writes to use cumulative values thus making the
app_pointer unecessary and removing it.
Only tested as far as build.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only tested as far as build.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The buffer passed to the copy callback should not be const because the
copy callback can be used for capture and playback.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MXrq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.10
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
Use the generic dmaengine PCM driver instead of a custom implemention. There is
a minor functional change, the ux500 PCM driver did not preallocate the audio
buffer, while the generic dmaengine PCM driver will do this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds two formats for Direct Stream Digital (DSD), a
pulse-density encoding format which is described here:
https://en.wikipedia.org/wiki/Direct_Stream_Digital
DSD operates on 2.8, 5.6 or 11.2MHz sample rates and as a 1-bit
stream.
The two new types added by this patch describe streams that are capable
of handling DSD samples in DOP format as 8-bit or in 16-bit (or at a x8
or x16 data rate, respectively).
DSD itself specifies samples in *bit*, while DOP and ALSA handle them
as *bytes*. Hence, a factor of 8 or 16 has to be applied for the sample
rare configuration, according to the following table:
configured hardware
176.4KHz 352.8kHz 705.6KHz <---- sample rate
8-bit 2.8MHz 5.6MHz
16-bit 2.8Mhz 5.6MHz 11.2MHz
`-----------------------------'
actual DSD sample rates
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unfortunately there are still quite a few platforms with a dmaengine driver
which do not support reporting the number of bytes left to transfer. If we want
to support these platforms in the generic dmaengine PCM driver we have.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for platforms which don't use devicetree yet or have to optionally
support a non-devicetree way to request the DMA channel. The patch adds the
compat_request_channel and compat_filter_fn callbacks to the
snd_dmaengine_pcm_config struct. If the compat_request_channel is implemented it
will be used to request the DMA channel. If not dma_request_channel with
compat_filter_fn as the filter function will be used to request the channel.
The patch also exports the snd_dmaengine_pcm_request_chan() function, since
compat platforms will want to use it to request their DMA channel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a generic dmaengine PCM driver. It builds on top of the
dmaengine PCM library and adds the missing pieces like DMA channel management,
buffer management and channel configuration. It will be able to replace the
majority of the existing platform specific dmaengine based PCM drivers.
Devicetree is used to map the DMA channels to the PCM device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_{add,remove}_platform are similar to snd_soc_register_platform and
snd_soc_unregister_platform with the difference that they won't allocate and
free the snd_soc_platform structure.
Also add snd_soc_lookup_platform which looks up a platform by the device it has
been registered for.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
