We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Mikael Starvik <starvik@axis.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In SiRF platform, there are different fifo size of uart and usp,
with the fifosize configuration changes in different chips, we
can not use port line to decide how to check FIFO full,empty and
level.
There is a direct mapping between FIFO HW register layout with
fifo size, so move to use fifosize as the input to check fifo
status.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In different platform of SiRF SoCs, there is no same uart and usp-uart
numbers, it is not convenient to use hard-coded ports array and port
lines.
here we drop the hard-coded ports table , and drop "cell-index". then
move to use alias id to get line.
for example:
aliases {
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
serial3 = &uart3;
serial4 = &uart4;
serial5 = &uart5;
serial6 = &uart6;
serial9 = &usp2;
};
at the same, enlarge the max port number according to the chip with the most
UART.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 8250 MTK UART driver to support earlycon device tree.
Earlycon take effect by
add "earlycon" in kernel boot argument
add "linux,sdtout-path" property in device tree file
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2ee6dfa0e.
Jakub Kiciński observed that this patch can cause the pl011
driver to hang if if the only process with a pl011 port open is
killed by a signal, pl011_shutdown() can get called with an
arbitrary amount of data still in the FIFO.
Calling _shutdown() with the TX FIFO non-empty is questionable
behaviour and my itself be a bug.
Since the affected patch was speculative anyway, and brings limited
benefit, the simplest course is to remove the assumption that TXIS
will always be left asserted after the port is shut down.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is pm_qos_add_request() being executed on serial_omap_probe(),
which stores "&up->pm_qos_request" from omap-serial driver to
"pm_qos_array[PM_QOS_CPU_DMA_LATENCY]->constraints". If
serial_omap_probe() fails after pm_qos_add_request() (e.g. on
uart_add_one_port() call), pm_qos_array still keeping pm_qos_request
struct from omap-serial driver, which is not valid anymore (since driver
failed). This leads further to kernel crash on pm_qos_update_target(),
executing from some completely different driver.
We were observing this while trying to run audio playback while having
one of omap-serial driver instances failed on uart_add_one_port() call:
Unable to handle kernel paging request at virtual address fffffffc
Backtrace:
(plist_add) from (pm_qos_update_target)
(pm_qos_update_target) from (pm_qos_add_request)
(pm_qos_add_request) from (snd_pcm_hw_params)
(snd_pcm_hw_params) from (snd_pcm_common_ioctl1)
(snd_pcm_common_ioctl1) from (snd_pcm_playback_ioctl1)
(snd_pcm_playback_ioctl1) from (snd_pcm_playback_ioctl)
(snd_pcm_playback_ioctl) from (do_vfs_ioctl)
(do_vfs_ioctl) from (SyS_ioctl)
(SyS_ioctl) from (ret_fast_syscall)
This patch adds pm_qos_remove_request() on fail path in
serial_omap_probe() in order to fix this issue. While at it, free the
wakeup settings on fail path as well, just like it's done in
serial_omap_remove().
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Log warnings meant to help diagnose problems setting up earlycon
are reporting false positives for 'console='. Revert to the
previous behavior which reported nothing.
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtk 8250 needs two clocks, one for providing the baudrate and
one that needs to be enabled for register accesses. The latter has
not been supported, this patch adds support for it. It is optional
for now since not all SoCs provide a bus clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime callbacks already enable and disable the device.
Use them in probe() and remove() instead of duplicating the
code. This allows us to concentrate more code for enabling/disabling
the UART in a single place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a struct device * is present clk_get should be used rather
than of_clk_get. Use the devm variant of this function to be able to
drop the clk_put in the error and remove pathes. While at it fix
a wrong error message.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver has probed successfully the clk pointer is always valid,
so no need to test for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function meson_uart_release_port() inappropriately try to
iounmap() a resource managed by devm_ioremap_nocache().
The function meson_uart_release_port() maybe called by uart_ioctl()
that means meson_uart_release_port() is not called from within a
probe or remove function, for safety, I convert iounmap() to
devm_iounmap().
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx_running flag should show if DMA is currently active. However
there is a window between when the flag is set/cleared and when
the DMA is started/stopped. Because the flag is queried from both
hard and soft irq contexts, the driver can make incorrect
decisions and do things like start a DMA transfer using a buffer
that is already setup to be used for a DMA transfer.
This patch adds a spinlock to synchronize the rx_running flag and
close the above mentioned window.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `ifx_spi_free_device':
ifx6x60.c:(.text+0x96d9a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ifx_spi_spi_probe':
ifx6x60.c:(.text+0x978a2): undefined reference to `dma_alloc_coherent'
While DMA is optional in this driver, and is used only if
ifx_modem_platform_data.use_dma is set, there are currently no in-tree
users of ifx_modem_platform_data (and thus of this driver), so just make
it depend on HAS_DMA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to cast the last parameter of {request,free}_irq() to
"void *", as any pointer type is accepted.
Remove the superfluous casts to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting spi_driver pointers to "void *" when calling
spi_{,un}register_driver() bypasses all type checking.
Remove the superfluous casts to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 52bec4ed4e("serial: sirf: add a new uart type
support").
we misunderstood the clock dependency in atlas7. Actually involved
several clocks are in a tree structure. we still only need to take
the leaf clock node for BT uarts.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove CONFIG_SERIAL_DETECT_IRQ and CONFIG_SERIAL_MANY_PORTS, and
substitute all references to the proper 8250 Kconfig options. Now, the
actual Kconfig dependencies are not hidden when reading the code and
static analyzers are less confused.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_ prefix is reserved for Kconfig options in Make and CPP
syntax; static analysis tools rely on this convention. This patch
enforces this behavior for SERIAL_BFIN_{HARD_}CTSRTS.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix reference on PPC_MPC52xx in C comment after #endif.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file local CPP identifier is not referenced anywhere else, so we
can safely remove it.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle the changed flag of IRQ status in interruption
instead of handling it in tasklet due to the tasklet
may be scheduled more than once in one interruption.
Otherwise, the changed status may be processed more
than once which will lead to unexpected result. And
seriously, kernel will crash.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'CONFIG_' prefix is reserved for Kconfig options in Make and CPP
syntax only. Remove this prefix from the self-defined CPP identifier to
apply to this convention and make static analysis tools happy.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ETRAX_SERIAL_PROC_ENTRY is not defined in Kconfig. The affected #ifdef
block has not been compiled for years, and the embedded macro, PROCSTAT,
ended up as a NOOP. Hence, remove the block and all calls to PROCSTAT.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ETRAX_RS485_{ON_PORT_G, LTC1387} are not defined in Kconfig. The
affected #ifdef block have not been compiled for years, so remove them
entirely.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ETRAX_EXTERN_PB6CLK_ENABLED is not defined in Kconfig. The affected
#ifdef block has not been compiled for years, so remove it entirely.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig option ARCH_SH7372 has been removed by commit 59b89af1d5
("ARM: shmobile: sh7372: Remove Legacy C SoC code"). This patch removes
the last reference on this Kconfig option.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the normal return values for bool functions
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_name no longer uses the buf parameter, so remove it along with all
the 64 byte stack buffers that used to be passed in.
Mostly generated by the coccinelle script
@depends on patch@
identifier buf;
constant C;
expression tty;
@@
- char buf[C];
<+...
- tty_name(tty, buf)
+ tty_name(tty)
...+>
allmodconfig compiles, so I'm fairly confident the stack buffers
weren't used for other purposes as well.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value from imx_setup_ufcr() is always 0 and its value is never
checked, so better to remove the return value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously Soft Reset (clear of SRST bit in UCR2 register)
of UART in startup is not protected by lock, which may have race
with console_write, as console_write may occur at anytime even
when UART port is shutdown.
To avoid this race, protect Soft reset of UART port with spin_lock.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 734745c serial/amba-pl011: Activate TX IRQ passively
adds some complexity and overhead in the form of a softirq
mechanism for transmitting in the absence of interrupts.
This patch simplifies the code flow to reduce the reliance on
subtle behaviour and avoid fragility under future maintenance.
To this end, the TX softirq mechanism is removed and instead
pl011_start_tx() will now simply stuff the FIFO until full
(guaranteeing future TX IRQs), or until there are no more chars
to write (in which case we don't care whether an IRQ happens).
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2ee6dfa0e.
Jakub Kiciński observed that this patch can cause the pl011
driver to hang if if the only process with a pl011 port open is
killed by a signal, pl011_shutdown() can get called with an
arbitrary amount of data still in the FIFO.
Calling _shutdown() with the TX FIFO non-empty is questionable
behaviour and my itself be a bug.
Since the affected patch was speculative anyway, and brings limited
benefit, the simplest course is to remove the assumption that TXIS
will always be left asserted after the port is shut down.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).
Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.
See: https://www.exar.com/common/content/document.ashx?id=1587 page 11
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes problems with serial console break. When function
s3c64xx_serial_startup() was started while serial console has been working,
it caused lose of characters written to TX FIFO. This effect was particularly
observable with systemd, which closes serial port every time when it's
not currently needed, hence function s3c64xx_serial_startup() is called
quite often there. To fix this problem we avoid resetting TX FIFO if port is
used as serial console.
Example of broken console log:
[ 1086.7 Expecting device dev-ttySAC1.device...
[ 1086.[ OK ] Reached target Paths.
[ 1086.756416] s[ OK ] Reached target Swap.
[ 1086.776413] systemd[1]: Reached target Swap.
[ 1086.776642] systemd[1]: Starting Root Slice.
[ 5.53403[ OK ] Created slice Root Slice.
[ 5.548433] systemd[1]: Create[ OK ] Created slice User and Session Slice.
[ 5.568414] sys[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 5.588388] s[ OK ] Listening on Delayed Shutdown Socket.
[ 5.608376] sy[ OK ] Listening on Journal Socket (/dev/log).
[ 5.628361] [ OK ] Listening on udev Kernel Socket.
[ 5.648357] s[ OK ] Listening on udev Control Socket.
[ 5.668353] s[ OK ] Listening on Journal Socket.
[ 5.688366] systemd[1]: Listeni[ OK ] Created slice System Slice.
[ 5.708393] Mounting Temporary Directory...
[ 7139.067436] Starting prepare device daemon...
[ 7139.091726] sy Starting Generate environment from /etc/profile.d...
[ 5.792867] system Starting Create Static Device Nodes in /dev...
[ 7848.718 Mounting Debug File System...
[ 7848.7384 Mounting Configuration File System...
[ 5.852 Starting Apply Kernel Variables...
[ 5.8720 Starting Setup Virtual Console...
[ 7848.798 Starting udev Coldplug all Devices...
[ 7848.817 Starting Journal Service...
[ OK ] Started Journal Service.
[ 7848.854222] s[ OK ] Reached target Slices.
Starting Remount Root and Kernel File Systems...
[ OK ] Mounted Configuration File System.
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.
When PORT_UNKNOWN is setup probe will fail anyway.
Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"
This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.
Fix both xilinx serial drivers in the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- DT endianness specification bindings
- Big endian 8250 serial support
- DT overlay unittest updates
- Various DT doc updates
- Compile fixes for OF_IRQ=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOG5kAAoJEMhvYp4jgsXihDgH/3pmPSjuRG1bhGssmnchHjWh
SU2eS2MZnlD60UqRt7jd3smCX2qL83tfwpFhOvCT9Mz775E7ggmYq9fS8pCYAbaD
x98mUrE2GzdUzlrL6RS8Z0ExjyGwbMoW3+cZtyPkmC6CsW0fwqEPmEyk7m+Hk8C3
w3pWG06o+G8UjiFmwbr8Pki2ykxvucr22NCzH4SS6bAD4QOrQO3v48QkUg7XFlVc
NHNzQbswL85uOJ7uuAbxg+s8TXkwcxUeMJEKldLrjuyppO3N1MjnOgCptnhVNOOb
zK+IsS378jMiNjAg2ui/BLH60N5yadkgk4+L4iPPy+y/yR61NCVXxRe11IQJxb0=
=rtv6
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some odd
reason, but Peter is working on fixing that. If not, I'll send a revert
for the offending patch, but I have faith that Peter can address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices in
the future.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IcUACgkQMUfUDdst+ylFqACcC8LPhFEZg9aHn0hNUoqGK3rE
5dUAnR4b8r/NYqjVoE9FJZgZfB/TqVi1
=lyN/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
If the device node has a "big-endian" property and 32-bit registers, tell
the serial driver to use UPIO_MEM32BE instead of UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add cases for UPIO_MEM32BE wherever there are currently cases handling
UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
* pnp:
PNP: Avoid leaving unregistered device objects in lists
PNP: Convert pnp_lock into a mutex
PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver
PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver
PNP: net/sb1000: Use module_pnp_driver to register driver
PNP: media/rc: Use module_pnp_driver to register driver
PNP: ide/ide-pnp: Use module_pnp_driver to register driver
PNP: ata/pata_isapnp: Use module_pnp_driver to register driver
PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver
PNP: Add helper macro for pnp_register_driver boilerplate
PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
Hardware is capable of inverting RTS signal when working
in RS-485 mode. Expose this functionality to user space.
Relay on a matching combination of standard flags
(SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND) to
detect when user space is requesting inverted RTS mode.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial ports of F81504/F81508/F81512 will failed when wakeup from S3(STR).
It's due to when the system wakeup from S3(STR), this PCI device's
configuration space from 0x40 to 0x40 + max_port * 0x08 should be
re-configured.
We move all initialization from pci_fintek_setup() to pci_fintek_init() and
set it to pci_serial_quirks .init section. It's will re-init this device when
system wakeup from pciserial_resume_ports().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the expected behavior of kernel command lines of the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
and
earlycon=uart[8250],io|mmio|mmio32,<addr>[,options]
earlycon=uart[8250],<addr>[,options]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore undocumented behavior of kernel command line parameters of
the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
where 'options' have not been specified; in this case, the hardware
is assumed to be initialized.
Fixes: c7cef0a849 ("console: Add extensible console matching")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.
Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specify transmit FIFO size which might be different depending on
LPUART instance. This makes sure uart_wait_until_sent in serial
core getting called, which in turn waits and checks if the FIFO
is really empty on shutdown by using the tx_empty callback.
Without the call of this callback, the last several characters
might not yet be transmitted when closing the serial port. This
can be reproduced by simply using echo and redirect the output to
a ttyLP device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exynos serial ports operate either in a DMA-based or interrupt-based
modes. In DMA-based mode, the UART generates a transfer data request
and a Transmission (Tx) interrupt in interrupt-based mode.
The Tx IRQ is only unmasked in interrupt-based mode and it was done
in s3c24xx_serial_start_tx(). Commit ba019a3e2a ("serial: samsung:
remove redundant interrupt enabling") removed the IRQ enable on that
function since it is enabled when the mode is set in enable_tx_pio().
The problem is that enable_tx_pio() is only called if the port mode
has not been set before but the mode was not cleared on .shutdown().
So if the UART was shutdown and then started up again, the mode set
will remain and the Tx IRQ won't be unmasked.
This caused a hang on at least Exynos5250, Exynos5420 and Exynos5800
when the system is rebooted or powered off.
Fixes: ba019a3e2a ("serial: samsung: remove redundant interrupt enabling")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clock rate is requested from a property called
"clock-frequency" in both dw8250_probe_of and
dw8250_probe_acpi. Moving the requests to dw8250_probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having ACPI handle does not mean the same as having ACPI
identifier. The check is in any case useless, but having it
prevents this driver from being used for example with
multifunctional PCI devices, such as the newer Intel LPSS
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Tangier contains 4 HSUART ports as found on Intel Edison board which are
8250 compatible. The patch adds necessary bits to the driver.
Note that the HSU port0 is currently unavailable and thus not supported.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for intel_mid_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) nominator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
24 25 12 48000000 64000000 4000000(1)
49 50 14 49000000 56000000 3500000(1)
4 5 16 40000000 40000000 2500000(1)
16 25 16 32000000 32000000 500000(4),1000000(2),2000000(1)
24 25 16 48000000 48000000 1500000(2),3000000(1)
2304 3125 16 36864000 36864000 576000(4),1152000(2)
8192 15625 16 26214400 26214400 50(32768),200(8192)
9216 15625 16 29491200 29491200 1800(1024),57600(32),115200(16),
230400(8),460800(4),921600(2),1843200(1)
12288 15625 16 39321600 39321600 75(32768),150(16384),300(8192),
600(4096),1200(2048),2400(1024),4800(512),
9600(256),19200(128),38400(64)
45056 78125 16 28835840 28835840 110(16384)
274432 390625 16 3512729635127296 134(16384)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for byt_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) numerator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
4 5 16 80000000 80000000 2500000(2)
14 25 16 56000000 56000000 3500000(1)
16 25 16 64000000 64000000 500000(8),1000000(4),2000000(2),
4000000(1)
24 25 16 96000000 96000000 1500000(4),3000000(2)
2180 3103 16 70254592 70254592 134(32768)
2304 3125 16 73728000 73728000 576000(8),1152000(4)
8192 15625 16 52428800 52428800 50(65536),200(16384)
9216 15625 16 58982400 58982400 1800(2048),57600(64),115200(32),
230400(16),460800(8),921600(4),1843200(2)
12288 15625 16 78643200 78643200 75(65536),150(32768),300(16384),
600(8192),1200(4096),2400(2048),
4800(1024),9600(512),19200(256),38400(128)
9893 17154 16 57671680 57671680 110(32768)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"brd->nasync" amd "brd->maxports" are the same. They hold the number of
filled out channels in the brd->channels[] array. These tests should
be ">=" instead of ">" so that we don't read one element past the end.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_console_setup() checks port->mapbase != 0, but the port may
not be initialized yet even if this condition is met [e.g., ioremap()
may have failed]. Check port->membase != NULL instead, similar to
cdns_early_console_setup().
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of cdns_uart_readl() and cdns_uart_writel() and just call
readl() and writel() directly.
Most of the patch was created by search-and-replace (I had to convert a
few lines manually, and break some lines longer than 80 columns):
* s/cdns_uart_readl(/readl(port->membase + /g
* s/cdns_uart_writel(\([^,]*\),/writel(\1, port->membase +/g
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_get_port() sets port->iobase = 1 to "mark port in use", but
this "in use" condition is not checked anywhere else in the code. So
remove the line, keeping port->iobase = 0 (which also makes more sense).
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code assumes that the array cdns_uart_port[] has dimension
CDNS_UART_NR_PORTS, so let us define it this way.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register space size is 0x1000, and this value [not 0xfff] should be
provided to request_mem_region(), ioremap(), etc.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the 8250 driver reserve exactly the mmio region specified
in the devicetree. This prevents conflicts between UPIO_AU type
UARTs and other devices mapped closer than the default size of
0x1000 (or 0x100 for RT2880).
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a mapsize field to struct uart_port to be used in
conjunction with mapbase. If set, it overrides whatever value
serial8250_port_size() would otherwise report.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current calculation method in the case of 9600bps, rounding error occurs
has become setting that occur timeout faster than the required time. When we
use 9600bps, 32byte buffer, 10 bit (CS8) and 100 HZ, it becomes 3 jiffies
(30msec). In fact it is necessary 33msec. This updates to the calculation
that are not actually less than the value set by the rounding error.
Also, this is nothing will be calculated value when there is no load. If there
are a lot of case load, overrun error will occur immediately.
This is by the buffer size to be calculated twice the DMA buffer, and add the
change of setting a sufficient time-out value.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA and SCIFB can detect the overrun, but it does not support.
This adds overrun handling of SCIFA and SCIFB.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although clk_disable_unprepare() is called both on .remove()
and in .probe() error path, the clock is never actually enabled.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EFCR register contains RS-485 configuration which should not
be changed by shutdown. Instead of doing a write only update
the appropriate bits.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ports are not explicitly removed on the error path
the device will not get properly unregistered leaving
/dev/ttySC* nodes in the filesystem.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When wakeirq is not used/enabled, "no wakeirq for uart0" is output for
all TTY as the log message is generated before the port line is
initialized.
[ 0.802656] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.811700] omap_uart 44e09000.serial: no wakeirq for uart0
[ 0.812379] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[ 1.503622] console [ttyO0] enabled
[ 1.509836] omap_uart 48022000.serial: no wakeirq for uart0
[ 1.516118] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[ 1.527711] omap_uart 48024000.serial: no wakeirq for uart0
[ 1.533881] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[ 1.545324] omap_uart 481a6000.serial: no wakeirq for uart0
[ 1.551410] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 60, base_baud = 3000000) is a OMAP UART3
[ 1.562946] omap_uart 481a8000.serial: no wakeirq for uart0
[ 1.569036] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61, base_baud = 3000000) is a OMAP UART4
Fix by moving wakeirq initialization, check, and dev_info() call to
after port line initialization and validation.
Signed-off-by: Doug Kehn <rdkehn@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This config no longer exists now that mach-msm has been removed.
Delete it and the associated code.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove pci_fintek_setup() non-used var with calculation ciobase
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial_core.h file have been included in header file
serial_8250.h. so remove the "#include <serial_core.h>" in
some 8250 serial drivers, because they have included the header file
serial_8250.h.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Au1x00/RT2800+ doesn't implement the 8250 scratch register (and
this may be true of other h/w currently supported by the 8250 driver);
read back the canary value written to the scratch register to enable
the console h/w restart after resume from system suspend.
Fixes: 4516d50aab ("serial: 8250: Use canary to restart console ...")
Reported-by: Mason <slash.tmp@free.fr>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Au1x00/RT2800+ hardware has an alternate register layout which is
remapped with lookup tables by the au_serial_in()/out() i/o accessors.
However, the h/w does not support the complete 8250 register set, and
accesses to unmapped registers cause out-of-bounds lookups. Further,
because the lookup tables are defined by designated initializers, the
tables may contain unmapped entries (although the current tables do not).
Declare fixed-size lookup tables with contiguous initialization for
the complete 8250 register map; unmapped registers are initialized to -1.
Validate the register index (ie., 'offset') is in the range [0, table size).
Return fixed value for unmapped register reads and ignore unmapped register
writes.
Reported-by: Mason <slash.tmp@free.fr>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The base port operations dispatch table should never be modified
at runtime; the proper way to override base port operations is
to dup the port operations, modify the copy, and point port->ops
at the copy.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; separate RSA probe and resource management
from base port operations. Override base port operations for the
config_port(), request_port() and release_port() methods to
implement the optional RSA probe and resource management only in
the universal/legacy 8250 driver.
Introduce 'probe' flags for 8250 ports, which allows drivers higher
up the driver stack to enable optional probes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe for Remote Supervisor Adapter is limited to port i/o
addresses which match one of the probe_rsa[] module parameter
addresses. Limit RSA resource acquire to matching i/o ports.
The result is a saner probe policy: only perform optional probes
when specified rather than by default.
NB: It is possible for userspace to set the port type == PORT_RSA
with ioctl(TIOCSSERIAL) and then autoconfig with ioctl(TIOCSERCONFIG),
which if it fails, may leave the port type set to PORT_RSA. Since
this may have previously resulted in a working RSA port, this behavior
is preserved.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for Remote Supervisor Adapter is conditional on
CONFIG_SERIAL_8250_RSA; only attempt RSA resource acquire if
defined.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; move default dma tx/rx handler initialization
into serial8250_set_defaults(), which allows default dma ops to
remain unexported from the base port operations module after the split.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; move fixed type initialization into
serial8250_set_defaults(). This enables uart_config[] array to remain
file scope in base port operations after the split.
NB: the call to serial8250_init_fixed_type_port() from
serial8250_register_ports() was added by commit b5d228cc4f
("serial: copy UART properties of UPF_FIXED_TYPE ports provisioned
using early_serial_setup") specifically to support ports initialized
by early_serial_setup(). Since serial8250_set_defaults() is called
from early_serial_setup(), fixed type initialization is now already
handled there before serial8250_register_ports() is called.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; introduce serial8250_set_defaults() to set default
port methods prior to driver override.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; introduce serial8250_init_port() to initialize
port fields uncoupled from port structure storage.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; decouple irq setup/teardown and handler from
core port operations.
Introduce setup_irq() and release_irq() 8250 driver methods; the 8250
core will use these methods to install and remove irq handling for
the given 8250 port.
Refactor irq chain linking/unlinking from 8250 core into
univ8250_setup_irq()/univ8250_release_irq() for the universal 8250 driver.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 core split; separate shared console interface from the
console definition of the universal driver.
Introduce 8250 shared console interface; serial8250_console_write() and
serial8250_console_setup() which decouples the console operation from
the port structure storage.
Rename existing serial8250_console* identifiers to univ8250_console*.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
setup_earlycon() will now match and register the desired earlycon
from the param string (as if 'earlycon=...' had been set on the
command line). Use setup_earlycon() from existing arch call sites
which start an earlycon directly.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Earlycon matching can only be triggered if 'earlycon=...' has been
specified on the kernel command line. To workaround this limitation
requires tight coupling between arches and specific serial drivers
in order to start an earlycon. Devicetree avoids this limitation
with a link table that contains the required data to match earlycons.
Mirror this approach for earlycon match by name. Re-purpose
EARLYCON_DECLARE to generate a table entry which associates name with
setup() function. Re-purpose setup_earlycon() to scan this table for
an earlycon match, which is registered if found.
Declare one "earlycon" early_param, which calls setup_earlycon().
This design allows setup_earlycon() to be called directly with a
param string (as if 'earlycon=...' had been set on the command line).
Re-registration (either directly or by early_param) is prevented.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate earlycon matching from registration; add register_earlycon
which initializes and registers the matched earlycon.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Earlycon param strings of the form
earlycon=<name>
are rejected from parse_options() with an error (which, in turn,
results in a NULL argument for the setup() method options parameter).
Only pass non-empty string to parse_options(); this will enable
handling actual parse errors differently than expected and allow
formats.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because setup_earlycon() continues to attempt console registration
if an error occurred parsing the option string, the actual value of
the error code from parse_options() is ignored.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If parsing failed to decode a valid uart addr, return -ENODEV instead
of success. Although setup_earlycon() will detect the failure anyway
(because the write() method has not been set), that behavior is not
obvious and should not be relied on.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The <baud><parity><bit> option string is not supplied if the earlycon
is started via devicetree and OF_EARLYCON_DECLARE(). The option string
is also not required if started via kernel command line parameters of
the form:
earlycon=uart,mmio,<addr>
console=uart,mmio,<addr>
If earlycon_device->baud is 0, then an option string was not supplied.
In this case, assume the uart has already been initialized by the
bootloader or firmware.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initializing the ->uartclk field is not related to option parsing;
relocate from parse_options() to setup_earlycon() (which mirrors the
behavior of of_setup_earlycon()).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
early_device was only required for serial8250_find_port_for_earlycon(),
which was replaced by extensible console matching.
Fixup early_serial8250_write() to get the earlycon_device * from
console->data (which is initialized by {of_}setup_earlycon()).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'/**' is required to start a kernel-doc comment block.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add match() method to struct console which allows the console to
perform console command line matching instead of (or in addition to)
default console matching (ie., by fixed name and index).
The match() method returns 0 to indicate a successful match; normal
console matching occurs if no match() method is defined or the
match() method returns non-zero. The match() method is expected to set
the console index if required.
Re-implement earlycon-to-console-handoff with direct matching of
"console=uart|uart8250,..." to the 8250 ttyS console.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; initialize the port flags based on the
"skip_txen_test" module param to use the existing flag test.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250_core.c file split; move shared inline function
to local header file.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since uart->port.type has just reset to PORT_UNKNOWN, capabilities
are reset to uart_config[PORT_UNKNOWN].flags, which is 0.
Removes unnecessary dependency on uart_config[].
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; calculate the ttyS index directly from
the port minor which avoids the global serial8250_reg reference
from base port operations.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART drivers that share ttyS namespace cannot trivially compute the
ttyS index from the port->line value since the minor_start may be
offset from minor 64. Further, to do so requires a pointer to the
uart driver since there is no back pointer from uart_port to
uart_driver.
Rather than have UART drivers computing the minor value by themselves,
encapsulate within the serial core at port registration time.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add irq disable and enable in bfin_serial_rx_dma_timeout in case of
system hang.
This reverts part of commit 9642dbe73c ("serial: bfin-uart: avoid
dead lock in rx irq handler in smp kernel").
Signed-off-by: Hao Liang <hliang1025@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are dealing with CTS, not DSR here (we dealt with DSR a few lines
above), so set appropriate bits.
Reported-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing some boilerplate by using module_pnp_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Trying to write console output from within the serial console driver
while the port->lock is held causes recursive deadlock:
CPU 0
spin_lock_irqsave(&port->lock)
printk()
console_unlock()
call_console_drivers()
serial8250_console_write()
spin_lock_irqsave(&port->lock)
** DEADLOCK **
The 8250_dw i/o accessors try to write a console error message if the
LCR workaround was unsuccessful. When the port->lock is already held
(eg., when called from serial8250_set_termios()), this deadlocks.
Make the error message a FIXME until a general solution is devised.
Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unacceptable levels of debug info will happen when the DMA driver defined in
the DT/ACPI is a blacklisted module.
Another cause for log polution would be the defer probing of the DMA driver
taking too long - in which case the message that this commit removes would be
cluttering the logs due to the init daemons activity.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following sparse warnings:
drivers/tty/serial/8250/8250_core.c:3231:32: warning: incorrect type in assignment (different base types)
drivers/tty/serial/8250/8250_core.c:3231:32: expected restricted upf_t [usertype] flags
drivers/tty/serial/8250/8250_core.c:3231:32: got unsigned int const [unsigned] flags
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 17b8f2a3fd ("serial: imx: add support for half duplex rs485")
introduced the following build warning:
drivers/tty/serial/imx.c: In function 'imx_set_termios':
drivers/tty/serial/imx.c:1301:7: warning: suggest explicit braces to avoid ambiguous 'else' [-Wparentheses]
Add the suggested braces to avoid the build warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 343fda9548 ("serial: mxs-auart: properly handle mctrl_gpio
failing") introduced the following build error:
CC drivers/tty/serial/mxs-auart.o
drivers/tty/serial/mxs-auart.c: In function 'mxs_auart_probe':
drivers/tty/serial/mxs-auart.c:1282:3: error: unknown type name 'got'
Fix it by providing a proper return code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other serial
driver bugfixes as well. Most notable is a wait_until_sent bugfix that
was traced back to being around since before 2.6.12 that Johan has fixed
up.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8RCYACgkQMUfUDdst+yk62QCgycxS4giC2hyRver3dyvaNR6g
zYYAn2w0uRndW+AqP4Tls54isRz6owpF
=gA2k
-----END PGP SIGNATURE-----
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
It is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ)
for requesting IRQ's resources any more, as they can be not ready yet in
case of DT-booting.
platform_get_irq() instead is a recommended way for getting IRQ even if
it was not retrieved earlier.
It also makes code simpler because we're getting "int" value right away
and no conversion from resource to int is required.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare to support console-defined matching; refactor the command
line parameter string processing from parse_options() into a
new core function, uart_parse_earlycon(), which decodes command line
parameters of the form:
earlycon=<name>,io|mmio|mmio32,<addr>,<options>
console=<name>,io|mmio|mmio32,<addr>,<options>
earlycon=<name>,0x<addr>,<options>
console=<name>,0x<addr>,<options>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tasklet may be scheduled and executed after serial port
was shutdown, for example, DMA rx callback will schedule the
tasklet while serial port is shutting down, especially serial
port is sending and receiving data in a higher baud rate and
it's killed by external program. In this case, tasklet_kill
can only clear the current scheduling out, so tasklet should
be disabled to prevent being executed in later scheduling.
Otherwise, the tasklet executed after serial port was shutdown
can lead to kernel crash.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The property in device tree will be reading each time when tty is opened,
so the ops of serial port should be set after that instead of setting once
in probe. Otherwise, the ops of serial port is inconsistent with the state
of serial work manner. For example, the atmel serial driver can't work when
switching to PIO mode due to DMA channel is not available.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function of atmel_init_property is to set the work manner of
atmel serial ports according to the property in device trees.
If DMA or PDC is not set or something goes wrong in getting property,
the work manner will switch to general PIO mode, thus there will
not be any failure case in this function. It's actually a procedure.
So changing the return type from int to void.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer size set in DMA is inconsistent with its allocation.
So keep them consistent here. The structure atmel_uart_char is
used in PIO mode with its meaning. But here in DMA, all of the
buffer is treated as general char.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only use buf of ring In DMA rx function while using buf of xmit
in DMA tx function. So in DMA rx we need definitively to check the
buf of ring which is corresponding to DMA rx function. And use macro
PAGE_ALIGNED to simplify the expression.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a race condition that happens when device_initcall(pl011_dma_initicall)
is executed before all the devices have been probed - this issue was observed on
a hisi_6220 SoC (HiKey board from Linaro).
The deferred driver probing framework relies on late_initcall to trigger
deferred probes so it is just possible that, even with a valid DMA driver ready
to be loaded, we fail to synchronize with it.
The proposed implementation delays probing the DMA until dma_startup.
As this is invoked on port startup and port resume - but DMA probing is only
required once - we avoid calling multiple times using a new field in
uart_amba_port to track this scenario.
This commit allows for subsequent attempts to associate an external DMA if the
DMA driver itself is not available (but present in the deferred probe pending
list).
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Getting the TX IRQ re-asserted from scratch can be inefficient in
some setups.
This patch avoids clearing the TX IRQ across pl011_shutdown()...
pl011_startup(), so that if the port is closed and reopened, the
IRQ will still work afterwards without having to bootstrap it again.
The TX IRQ continues to be masked in IMSC when the UART is not in
use.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current PL011 driver transmits a dummy character when the UART
is opened, to assert the TX IRQ for the first time
(see pl011_startup()). The UART is put in loopback mode temporarily,
so the receiver presumably shouldn't see anything.
However...
At least some platforms containing a PL011 send characters down the
wire even when loopback mode is enabled. This means that a
spurious NUL character may be seen at the receiver when the PL011 is
opened through the TTY layer.
The current code also temporarily sets the baud rate to maximum and
the character width to the minimum, to that the dummy TX completes
as quickly as possible. If this is seen by the receiver it will
result in a framing error and can knock the receiver out of sync --
turning subsequent output into garbage until synchronisation
is reestablished. (Particularly problematic during boot with systemd.)
To avoid spurious transmissions, this patch removes assumptions about
whether the TX IRQ will fire until at least one TX IRQ has been seen.
Instead, the UART will unmask the TX IRQ and then slow-start via
polling and timer-based soft IRQs initially. If the TTY layer writes
enough data to fill the FIFO to the interrupt threshold in one go,
the TX IRQ should assert, at which point the driver changes to
fully interrupt-driven TX.
In this way, the TX IRQ is activated as a side-effect instead of
being done deliberately.
This should also mean that the driver works on the SBSA Generic
UART[1] (a cut-down PL011) without invasive changes. The Generic
UART lacks some features needed for the dummy TX approach to work
(FIFO disabling and loopback).
[1] Server Base System Architecture (ARM-DEN-0029-v2.3)
http://infocenter.arm.com/
(click-thru required :/)
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix return from sprd_handle_irq() with spin_lock held.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All instances of "ttyPS" use this macro except for this one. Convert
it.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Spreadtrum UART is accessed with mmio; declare the proper iotype.
Also prevent userspace from assigning any other iotype via
ioctl(TIOCSSERIAL).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmitter is expected to be controlled by the UART's RTS pin.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for IRDA was added in 2009 in commit v2.6.31-rc1~399^2~2. There
are no in-tree users.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no benefit in keeping this information in RAM when it's not
used any more, so better use function local variables instead.
These members are unused since c0d1c6b0f0 ("serial: imx: Fix the
reporting of interrupts")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This if (0) exists since the driver was introduced in commit
c49bde83eb6a ([ARM PATCH] 1956/2: Re: Motorola i.MX serial driver)
back in 2004.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The writeable bits in the USR2 register are all "write 1 to
clear" so only write the bits that actually should be cleared.
Fixes: f1f836e420 ("serial: imx: Add Rx Fifo overrun error message")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a native 8250 driver carrying the Intel MID serial devices the
specific support is not needed anymore. This patch removes it for Intel MID.
Note that the console device name is changed from ttyMFDx to ttySx.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Penwell supports 3 HSUART ports which are 8250 compatible. The patch adds
necessary bits to the driver.
The functions have intel_mid_* prefix due to more than one platform will use
this code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code uses the alias id as array subscript of ar933x_console_ports.
So the valid id is 0 ... CONFIG_SERIAL_AR933X_NR_UARTS - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of ignoring errors returned by devm_gpiod_get_index use
devm_gpiod_get_index_optional which results in slightly more strict
error handling which is good.
Also use the fourth parameter to devm_gpiod_get_index_optional to be
able to drop the explicit direction setting.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers using mctrl-gpio must not pass invalid values for struct
mctrl_gpios *. All drivers were fixed in this regard and so some checks
can go away or be simplified.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If mctrl_gpio_init returns an error code this value should be forwarded and
the driver must not simply ignore this failure.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mctrl_gpio_init is fully aware of being optional. If it returns an error
code this indicates a real error that must not be ignored.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mctrl_gpio_init at present doesn't return NULL. (It might be used in the
future when no gpios are to be used indicating success.) Properly pass
error returned and also make driver probing fail on error.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UBRC is a read-only register, so we should not store and restore it inside
imx_flush_buffer().
Reported-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch fixes following sparse warnings:
bcm63xx_uart.c:857:43: warning: Using plain integer as NULL pointer
bcm63xx_uart.c:871:35: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this the module does not load automatically whenever suitable
platform device appears.
Reported-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building sprd_serial.o when CONFIG_PM_SLEEP is not defined triggers
these warnings:
drivers/tty/serial/sprd_serial.c:755:12: warning: ‘sprd_suspend’ defined but not used [-Wunused-function]
static int sprd_suspend(struct device *dev)
^
drivers/tty/serial/sprd_serial.c:764:12: warning: ‘sprd_resume’ defined but not used [-Wunused-function]
static int sprd_resume(struct device *dev)
^
Let's compile these functions only when CONFIG_PM_SLEEP is defined.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the legacy system PM callbacks to new ones. Meanwhile, remove the
redudant calls to the PCI for changing a power state since it's done by bus
code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current kernel, the CONFIG_PPC_OF is always 'y' for the ppc
arch. So we don't need to check it with other ppc specific options.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As more ARM platforms are moving into ARCH_MULTIPLATFORM, we can now
have integrator and versatile in the same kernel, and first one selects
this driver, causing a Kconfig warning:
warning: (ARCH_INTEGRATOR_AP) selects SERIAL_AMBA_PL010 which has unmet direct dependencies (TTY && HAS_IOMEM && ARM_AMBA && (BROKEN || !ARCH_VERSATILE))
It turns out that it has not been broken on versatile for a long time,
so we can remove the statement here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These quirk entries have the same effect as default
quirk entry, so we can just delete them.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b5c913f7e
("serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection")
trigger one redundant entry report message.
This patch fix it.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I'm still receiving reports to my email address, so let's point this
at the linux-serial mailing list instead.
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0aa525d118.
The conditional RX-FIFO read seems to cause spurious interrupts and we
see just:
|serial8250: too much work for irq29
The previous behaviour was "default" for decades and Marvell's 88f6282 SoC
might not be the only that relies on it. Therefore the Omap fix is
reverted for now.
Fixes: 0aa525d118 ("tty: serial: 8250_core: read only RX if there is
something in the FIFO")
Reported-By: Nicolas Schichan <nschichan@freebox.fr>
Debuged-By: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6d01bb9dc8.
The exact same code was added in commit 3239fd31d4 (serial: of-serial: fetch
line number from DT) a few lined above. Doing this once should be enough.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ line connected to the DBGU UART is often shared with a timer device
which request the IRQ with IRQF_NO_SUSPEND.
Since the UART driver is correctly disabling IRQs when entering suspend
we can safely request the IRQ with IRQF_COND_SUSPEND so that irq core
will not complain about mixing IRQF_NO_SUSPEND and !IRQF_NO_SUSPEND.
Rework the interrupt handler to wake the system up when an interrupt
happens on the DEBUG_UART while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
UARTs which do not trigger THRE interrupt if the fifo is already
empty when the interrupt is enabled need tx primed manually. These
UARTs are identified by the UART_BUG_TXEN flag to enable the
required workaround.
However, the current workaround is broken; if the fifo is already
empty but the shifter is still transmitting, then serial8250_tx_chars()
will not be called but no further THRE interrupt will occur, and
tx will stall. The appropriate check is for fifo empty (THRE), not
transmitter empty (TEMT).
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
[pjh: rewrote commit log]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the last missing piece to get a kernel booting to a prompt in qemu-cris.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The general agreed way to specify a fixed line number
for a serial console is to provide a "serial" alias
in the devicetree. Start parsing this property in
of_serial.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EarlyCon support depends on serial console infrastructure, so the code
implementing it should depend on CONFIG_SERIAL_SAMSUNG_CONSOLE.
This patch fixes the following build break:
CC [M] drivers/tty/serial/samsung.o
drivers/tty/serial/samsung.c:2468:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2468:1: error: expected declaration specifiers or ‘...’ before ‘s3c2410_setup_earlycon’
drivers/tty/serial/samsung.c:2487:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2487:1: error: expected declaration specifiers or ‘...’ before ‘s3c2412_setup_earlycon’
drivers/tty/serial/samsung.c:2488:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2488:1: error: expected declaration specifiers or ‘...’ before ‘s3c2440_setup_earlycon’
drivers/tty/serial/samsung.c:2489:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2489:1: error: expected declaration specifiers or ‘...’ before ‘s3c6400_setup_earlycon’
drivers/tty/serial/samsung.c:2506:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2506:1: error: expected declaration specifiers or ‘...’ before ‘s5pv210_setup_earlycon’
drivers/tty/serial/samsung.c:2507:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2507:1: error: expected declaration specifiers or ‘...’ before ‘exynos4210_setup_earlycon’
drivers/tty/serial/samsung.c:2468:1: warning: ‘s3c2410_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2487:1: warning: ‘s3c2412_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2488:1: warning: ‘s3c2440_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2489:1: warning: ‘s3c6400_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2506:1: warning: ‘s5pv210_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2507:1: warning: ‘exynos4210_setup_earlycon’ defined but not used [-Wunused-function]
make[3]: *** [drivers/tty/serial/samsung.o] Error 1
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/8250/8250_core.c:2503:6: sparse: symbol 'serial8250_set_divisor' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a full sc9836-uart driver for SC9836 SoC which is based on the
spreadtrum sharkl64 platform.
This driver also support earlycon.
Originally-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function s3c24xx_serial_start_tx_pio() enables interrupts if needed,
so we don't have to (or even we shouldn't) enable them before.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP UART ignores MCR[1] (ie., RTS) when in autoRTS mode. This
makes it impossible for either the serial core or userspace to
manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88838d3112702 ("serial: omap_8250: Fix RTS handling") fixed
RTS pin control when in autoRTS mode.
New support added in "serial: core: Rework hw-assisted flow control support"
enables a much simpler approach; rather than masking out autoRTS
whenever writing the EFR register, use the UPSTAT_* mode to determine if
autoRTS should be enabled when raising RTS (in omap8250_set_mctrl()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw-assisted flow control support was added to the serial core
in v3.8 with commits,
dba05832cb ("SERIAL: core: add hardware assisted h/w flow control support")
2cbacafd7a ("SERIAL: core: add hardware assisted s/w flow control support")
9aba8d5b01 ("SERIAL: core: add throttle/unthrottle callbacks for hardware
assisted flow control")
Since then, additional requirements for serial core support have arisen.
Specifically,
1. Separate tx and rx flow control settings for UARTs which only support
tx flow control (ie., autoCTS).
2. Disable sw-assisted CTS flow control in autoCTS mode
3. Support for RTS flow control by serial core and userspace in autoRTS mode
Distinguish mode from capability; introduce UPSTAT_AUTORTS, UPSTAT_AUTOCTS
and UPSTAT_AUTOXOFF which, when set by the uart driver, enable serial core
support for hw-assisted rx, hw-assisted tx and hw-assisted in-band/IXOFF
rx flow control, respectively. [Note: hw-assisted in-band/IXON tx flow
control does not require serial core support/intervention and can be
enabled by the uart driver when required.]
These modes must be set/reset in the driver's set_termios() method, based
on termios settings, and thus can be safely queried in any context in which
one of the port lock, port mutex or termios rwsem are held. Set these modes
in the 2 in-tree drivers, omap-serial and 8250_omap, which currently
use UPF_HARD_FLOW/UPF_SOFT_FLOW support.
Retain UPF_HARD_FLOW and UPF_SOFT_FLOW as capabilities; re-define
UPF_HARD_FLOW as both UPF_AUTO_RTS and UPF_AUTO_CTS to allow for distinct
and separate rx and tx flow control capabilities.
Disable sw-assisted CTS flow control when UPSTAT_AUTOCTS is enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PXA variant of the 8250 UART adds a UART enable bit which must not
be cleared. Make the earlycon support maintain this bit if it is set.
This implies some initialization of the UART, but we cannot
unconditionally set the bit as some other variants require this bit to
be clear for other functions.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mrvl,pxa-uart and mrvl,mmp-uart compatible strings for the of_serial
driver. These are 8250 variants which have a port type of PORT_XSCALE.
There is also the serial driver pxa.c with these compatible strings
already. However, it can be replaced with the common 8250 driver. It has
some issues like it cannot coexist with the 8250 driver due to tty name
collision. That also means adding these compatible strings here should
not case a problem.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for alias parsing from the DT. This allows for consistent
tty numbering.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port shadow registers, ->fcr and ->mcr, must be protected from
concurrent updates. Relocate the shadow register updates in
serial8250_do_set_termios() to the port lock critical section.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using no_console_suspend, the serial console may be powered off
anyway during system sleep. Upon resume, the port may be in its default
power-on state, but is expected to continue console i/o before the device
has received its pm callback. The resultant garbage i/o can cause all
kinds of havoc on the remote end.
Use the scratch register as a canary to discover if the console
has been powered-off. Write a non-zero value to the scratch register
at port suspend and reprogram the port before any console i/o if the
scratch register != canary before port resume.
This workaround is disabled for omap_8250 (which uses different divisor
programming).
Credit to Doug Anderson <dianders@chromium.org> for the idea of using
the scratch register canary to discover port power-down.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar XR17V35X PCIe uarts support a 4-bit fractional divisor register.
Refactor the divisor calculation from the divisor programming.
Allow a fractional result from serial8250_get_divisor() and pass this
result to serial8250_dl_write().
Simplify the calculation for quot and quot_frac. This was verified
to be identical to the results of the original calculation with a test
jig.
NB: The results were also compared with the divisor value chart
on pg 33 of the Exar XR17V352 datasheet, rev 1.0.3, here:
http://www.exar.com/common/content/document.ashx?id=1585
which differs from the calculated values by 1 in the fractional result.
This is because the calculated values are still rounded in the
fractional result, whereas the table values are truncated. Note
that the data error rate % values in the datasheet are for
rounded fractional results, as the truncated fractional results
have more error.
Cc: Joe Schultz <jschultz@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor divisor register programming into a new function,
serial8250_set_divisor; this allows serial console to reinitialize
early after resume from suspend.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the computation of the LCR register value from termios c_cflag
into a new local function, serial8250_compute_lcr().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_BUG_QUOT workaround adjusts the divisor computed from the
baud rate by serial8250_get_divisor(). Move the workaround into
serial8250_get_divisor(), so that divisor-from-baud computation
is encapsulated.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
16z135 IP Core has changed so the driver needs to be updated to respect
these changes. The following changes have been made:
* Don't invert the 16z135 modem status register when reading.
* Add module parameter to configure the (baud rate dependent) RX timeout.
Character timeout in seconds = (timeout_reg * baud_reg * 4)/freq_reg.
* Enable the handling of UART core's automatic flow control feature.
When AFE is active disable generation of modem status IRQs.
* Rework the handling of IRQs to be conform with newer FPGA versions and
take precautions not to miss an interrupt because of the destructive read
of the IIR register.
* Correct men_z135_handle_modem_status(), MSR is stat_reg[15:8] not
stat_reg[7:0]
* Correct calling of uart_handle_{dcd,cts}_change()
* Reset CLOCAL when CRTSCTS is set
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the uart port being suspended is a console and consoles are
not suspending (kernel command line contains no_console_suspend),
then no action is performed for that port, and the function can
return early.
If the function has not returned early, then one of the conditions
is not true, so the expression
(console_suspend_enabled || !uart_console(uport))
must be true and can be eliminated.
Similarly, the expression
(console_suspend_enabled && uart_console(uport))
simplifies to just uart_console(uport).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for early console initialized from device tree
and kernel command line to all variants of Samsung serial driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[mszyprow: added support for command line based initialization,
fixed comments, added documentation]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver cannot return from overrun error if characters
are output during overrun process, use dev_dbg() instead of
dev_notice() to log the error message of overrun in syslog.
Based on a patch by Hisashi Nakamura.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we would like to send amount of data less than FIFO size we better would do
this via PIO mode. Otherwise the overhead could be significant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we return in the first branch the second one doesn't require an
additional else keyword. The patch removes it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to use sci_{suspend|remove}() for the PM {freeze|
thaw|restore}() methods. It's handy to achieve this by using SIMPLE_DEV_PM_OPS()
macro, however we have to annotate sci_{suspend|remove}() with '__maybe_unused'
in order to avoid compilation warnings when CONFIG_PM_SLEEP is undefined.
Based on orignal patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implementation of flushing the RX FIFO breaks in a number of cases,
it is impossible to ensure an complete flush of the RX FIFO due to the
hardware not allowing the use of the FIFOs when the receiver is disabled
(Reading from the FIFO register does not remove it from the FIFO when
the RX_EN=0 or RX_DIS=1). Additionally during an initial set_termios
call where RX_DIS=1 causes a hang waiting forever for the RX FIFO to
empty. On top of this the FIFO will be cleared by the use of the RXRST
bits on the Control Register, making the RX flush pointless (as it does
not preserve the data read anyway).
Due to the TXRST the TX FIFO and transmitter can be interrupted during
frame trasmission, causing corruption and additionally data lost in the
FIFO. Most other serial drivers do not flush or clear the FIFOs during
a termios configuration change and as such do not have issues with
corruption. For this UART controller is it required that the TXRST/RXRST
bit be flagged during the change, this means that the data in the FIFO
will be dropped when changing configuration. In order to prevent data
loss and corruption of the transmitted data, wait until the TX FIFO is
empty before changing the configuration. The performance of this may
cause the set_termios call to take a longer amount of time especially
on lower baud rates, however it is comparable to the same performance
hit that a console_write call costs.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Acked-by: Anirudha Sarangi <anirudh@xilinx.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to explicitly zero the 'ret' variable as it is properly
initialized in a few lines below as:
ret = serial_mxs_probe_dt(s, pdev);
Remove the unneeded zeroing of 'ret'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should check whether platform_get_irq() failed, and in the case of error
this needs to be propagated.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The irq number is only used inside the probe function, so there is no need
to keep it in the private mxs_auart_port structure.
Use a local 'irq' variable for storing the irq number instead.
Also make its type of 'int' as platform_get_irq() may fail and return a
negative number.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Digicolor USART hardware does not support detecting the BREAK condition.
This means that we can't support sysrq on this hardware. Remove all reference
to sysrq from the code.
This also fixes build when sysrq is disabled:
drivers/tty/serial/digicolor-usart.c: In function 'digicolor_uart_console_write':
drivers/tty/serial/digicolor-usart.c:407:33: error: 'struct uart_port' has no member named 'sysrq'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the kernel command line parameter, no_console_suspend, is used,
the console should continue to output console messages during and
after system suspend. For a serial console, the serial core ensures
that the device is not shutdown when no_console_suspend is specified.
However, the default operation of the pnp bus will disable and suspend
the device and no further output occurs.
When registering the 8250 port, if the serial device is a console
set the PNP_CONSOLE capability, which prevents device power-off
if consoles are not suspending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unregister_console() will be called from uart_remove_one_port() while
removing the platform driver. So not necessary to call it in driver
exit path.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change does following:
- baud, flow, bits, parity were being overwritten as they were
being reinitialized after parsing. Initialize them when they are
declared so that user provided setting are not overwritten.
- msm_set_baud_rate() is anyway called in uart_set_options when it calls
msm_set_termios(). msm_reset() is called when we change the baud rate.
Hence doing away with both of these calls.
- CR_CMD_PROTECTION_EN and CR_TX_ENABLE settings are done in msm_set_baud_rate.
So do away with this here.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Moorestown platform support was removed few years ago. This is a follow
up which removes Moorestown specific code for the serial devices. It includes
mrst_max3110 and earlyprintk bits.
This was used on SFI (Medfield, Clovertrail) based platforms as well, though
new ones use normal serial interface for the console service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running an userspace program that does a 'tcflush(fd, TCIOFLUSH)' call
we still see the last received character in the URXD register afterwards.
Clear UCR2_SRST bit so that the UART FIFO is flushed properly.
Since UCR2_SRST also resets some UART registers, we need to save and restore
some of them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Acked-by: Jason Liu <r64343@freecale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On uart buffer flush, serial core resets the circular buffer.
If a DMA transfer is in progress at that time, the callback
lpuart_dma_tx_complete will move buffer's tail unconditionally,
hence tail moves beyond head. Use the flush_buffer hook to
terminate the DMA imeaditely and avoid lpuart_dma_tx_complete
being called in this situation.
This bug often showed up while shutdown and lead to duplicate
serial console output.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For power management support, we should disable TX and
TX interrupt so that kernel can prepare for deep sleep.
Retain RX and RX interrupt for wakeup the kernel when
receive the input character.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To end a DMA transfer which did not consume a whole buffer (e.g. one
character only), a RX timer is used. When lots of data are received
the DMA transfer will complete and setup another DMA transfer, which
in turn might complete again. In this cases, it is not necessary to
abort the DMA transfers using the RX timer. This change pushes the
RX timer timeout into the future each time a DMA transfer completed.
Aborting the DMA was not very harmful, since the next received
character lead to setup of another RX DMA.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the DMA channel request to probe to avoid requesting the DMA
channel on each opening of the ttyLPx device. This also fixes a
potential issue that TX channel is not freed when only RX channel
allocation fails. The DMA channels are now handled independently,
so one could use UART with DMA only in TX direction for instance.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:
[ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
[ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
[ 74.373960] LR is at lpuart_int+0x15c/0x3d8
[ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
[ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
[ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
[ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
[ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
[ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
[ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...
Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.
This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:
[ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.516590] pgd = 86348000
[ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[ 7.526145] Internal error: Oops: 17 [#1] ARM
[ 7.530611] Modules linked in:
[ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
[ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
[ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
[ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
[ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
[ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
[ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
[ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
[ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In early 8250, IER is already zero so no point in writing this - twice
per line
This helped improve the SystemC model based ARC OSCI platform
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
-FCR[RTL] = 00 1 byte
-FCR[RTL] = 01 16 bytes
-FCR[RTL] = 10 32 bytes
-FCR[RTL] = 11 56 bytes
-tx_loadsz is set to 63-bytes instead of 64-bytes to implement
workaround of errata A-008006 which states that tx_loadsz should
be configured less than Maximum supported fifo bytes
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When IGNPAR is set in termios->c_iflag, characters with
framing errors should be ignored.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNPAR/INPCK are clear in termios->c_iflag, characters
received with parity or framing errors should be preserved
and passed to the upper layers of the tty stack.
Specifically, the decision of whether to set the character
value to zero should be made by n_tty.c/n_tty_receive_parity_error().
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RX DMA transfers support for samsung serial driver. It's enabled
when DMA controller for RX channel is specified in device-tree.
DMA transactions are started when number of bytes in RX FIFO reaches
trigger level, otherwise PIO mode is used. DMA transfer size is always
PAGE_SIZE which can cause large latency when smaller data amount is
transferred, so we always terminate DMA transaction on RX timeout
interrupt. Timeout interval is set to 64 frame times.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add TX DMA transfers support for samsung serial driver. It's enabled
when "dmas" property is defined in serial device-tree node, otherwise
TX transfers are prerformed using PIO.
TX DMA is used for data segments larger than fifosize to reduce number
of interrupts during data transmission. For buffers shorter than fifosize
PIO mode is selected.
Data blocks for DMA transfers are aligned to cache line size to avoid
problems with coherency (some areas of TX circ buffer can be used by
CPU during DMA transaction, so we have to ensure that our data is always
consistent).
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add functions requesting and releasing RX and TX DMA channels. This
function are called only when "dmas" property in serial device-tree
node is defined.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have "dmas" property in serial node in device-tree, we do
memory alocation for dma structure which will be used in DMA handling
code.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This struct contains DMA configuration for each serial port.
It will be used in next commits adding DMA support in driver.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds Software flow control support in DMA mode.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After send out x_char in UART driver, x_char needs to be cleared
by UART driver itself, otherwise data in TXFIFO can no longer be
sent out.
Also tx counter needs to be increased to keep track of correct
number of transmitted data.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other than enable Receiver Overrun Interrupt Enable (UCR4_OREN)
in start_tx interface, UCR4_OREN should be enabled before enable
of Receiver.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Start rx_dma once RXFIFO is not empty that can avoid dma request lost
and causes data delay issue.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA mode for UART can be used even w/o HW flow control with RTS/CTS.
So it need to be initialized and enabled earlier.
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Terminating the DMA, make sure the interrupt is disabled, too.
This fixes random kernel Oops due to dma_tx_call() called for
invalid transmissions.
If we disable the TDMAEN, make sure it's enabled again if a TX
DMA is started.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in dma_tx_callback(), no matter if there is still
remaining data pending in circle buffer or not, DMA transmit
will be terminated.
This will result in some data never get transmitted.
In order to fix this issue, call imx_dma_tx() again in
dma_tx_callback, when there is pending data and uart hasn't
been stopped.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2ad28e3efe.
Instead of always wake up write_wait process in TX callback,
TX callback should call imx_dma_tx() again, and let imx_dma_tx
transfer the remaining data in circle buffer.
The issue with commit 2ad28e3 is, in case there is remaining
data in circle buffer, but no process is waiting on write_wait
queue, then as no following uart_write() will be called after
uart_write_wakeup(), thus cause data loss.
Moreover according to Documentation/serial/driver, uart_write_wakeup()
should be called in case the transmit buffer have dropped below
a threshold.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To synchronize between dma_tx_callback() and imx_dma_tx() use the same
variable, dma_is_txing. This prevents any race between these two functions
and ensures that a new DMA can start only after the first has been
finished.
Before the new DMA can be set up, update the circular buffer logic, first.
Therefore, change dma_is_txing after that update, instead of before.
While doing this, in dma_tx_callback() extend the locking to dma_unmap_sg()
and the update of dma_is_txing.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, reformat the code to exit immediately. This allows us to add
more code in more readable format.
In case the TX DMA was still running, remove and disable it's resources.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case dmaengine_prep_slave_sg() fails, add the missing dma_unmap_sg().
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inverting the logic of the if statement for the sg initialization
makes the if statement easier and better to read.
No functional change.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use imx_start_tx() just to enable the TX interrupt. It's the job of the
TX interrupt ISR to fill the transmit buffer, then. If the transmit buffer
is empty, the TX interrupt should be executed as soon as the start_tx()
enables the interrupt, so there is no reason for the extra
imx_transmit_buffer() call, here. Remove it.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Lowe <andy_lowe@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several places are accessing the UCR1 register without locking.
This probably will cause a race issue when another thread
is accessing the same register.
Add locking to preventing concurrent access of the UCR1 register.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CREAD flag hanlding in set_termios and UART DMA mode
which ignores all received chars when CREAD flag cleared.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes many bugs in the code dealing with the hardware handshake.
As an example, in atmel_set_termios(), we used to test whether the CRTSCTS
c_cflag was set. If so, we selected the "Hardware Handshake" mode through the
Mode Register. However, few lines below the mode was reset to "Normal" (0).
So there was no way to select the "Hardware Handshake" mode. To fix this issue,
we moved the CRTSCRTS c_cflag test AFTER the mode has been reset to "Normal".
Also setting the RTSEN and RTSDIS bits in the Control Register has different
results whether the USART is set in "Normal" or "Hardware Handshake" mode:
1) "Normal" mode
- the RTSEN bit forces the RTS line to low level, which tells the remote peer
that we are ready to received new data.
- the RTSDIS bit forces the RTS line to high level, which tells the remote peer
to stop sending new data.
2) "Hardware Handshake" mode
- the RTSEN bit forces the RTS line to high level.
- the RTSDIS bit lets the hardware control the RTS line.
WARNING:
when FIFOs are not available or not enabled, the RTS line is controlled by the
PDC. This is why using the Hardware Handshake mode requires using the PDC
channel for reception. However the Hardware Handshake mode DOES NOT work with
DMA controller since it cannot control the RTS line.
Future designs with FIFOs will introduce a new feature: the RTS line will be
controlled by the RX FIFO using thresholds. This patch was tested with this new
design.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-EDEFER error wasn't handle properly by atmel_serial_probe().
As an example, when atmel_serial_probe() is called for the first time, we pass
the test_and_set_bit() test to check whether the port has already been
initalized. Then we call atmel_init_port(), which may return -EDEFER, possibly
returned before by clk_get(). Consequently atmel_serial_probe() used to return
this error code WITHOUT clearing the port bit in the "atmel_ports_in_use" mask.
When atmel_serial_probe() was called for the second time, it used to fail on
the test_and_set_bit() function then returning -EBUSY.
When atmel_serial_probe() fails, this patch make it clear the port bit in the
"atmel_ports_in_use" mask, if needed, before returning the error code.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel_serial_probe() calls atmel_init_port(). In turn, atmel_init_port() calls
clk_disable_unprepare() to disable the peripheral clock before returning.
Later atmel_serial_probe() accesses some I/O registers such as the Mode and
Control registers for RS485 support then the Name and Version registers, through a call to
atmel_get_ip_name(), but at that moment the peripheral clock was still
disabled.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MARCO will not be supported any more and the project was dropped.
it has been replaced by CSR atlas7.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
