This patch fixes the problem where the ethtool Supported link
modes list backplane interfaces on X722 devices for 10GbE with
SFP+ and Cortina retimer. This patch fixes the problem by setting
and using a flag for this particular device since the backplane
interface is only between the internal PHY and the retimer and it
should not be seen by the user as they cannot use it.
Without this patch, the user wrongly thinks that backplane interfaces
are supported on their device when they actually are not.
Change-ID: I3882bc2928431d48a2db03a51a713a1f681a79e9
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed some of unnecessary if statements and unreachable code found by
static code analysis tool.
The return value of i40e_vsi_control_rings(..., false) is always 0. So,
test for non-zero will never be true. The function has been split into
"int i40e_vsi_start_rings()" and "void i40e_vsi_stop_rings()" for better
understanding.
Similarly, the function i40e_vsi_kill_vlan() never fails. So, checking
for return value is also unnecessary. Function definition changed to void.
The i40e_loopback_test() function is not implemented. The function and
all references to loopback testing were removed.
Change-ID: Id45cf66f6689ce2bc4e887de13f073e30e8431bd
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a common method for finding a VSI by type. The main
motivation for doing this is that the Flow Director path actually had two
ways of handling this, one stopped on first match and one did not. This
patch makes it so that all callers of this function will get the same
approach for finding a VSI.
Change-ID: Ibf25de8acd8466582520694424aa87da66965fbd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current Rx timestamp hang logic is not very robust because it does
not notice a register is hung until all four timestamps have been
latched and we wait a full 5 seconds. Replace this logic with a newer Rx
hang detection based on storing the jiffies when we first notice
a receive timestamp event. We store each register's time separately,
along with a flag indicating if it is currently latched. Upon first
transitioning to latch, we will update the latch_events[i] jiffies
value. This indicates the time we first noticed this event. The watchdog
routine will simply check that the either the flag has been cleared, or
we have passed at least one second. In this case, it is able to clear
the Rx timestamp register under the assumption that it was for a dropped
frame. The benefit if this strategy is that we should be able to
detect and clear out stalled RXTIME_H registers before we exhaust the
supply of 4, and avoid complete stall of Rx timestamp events.
Change-ID: Id55458c0cd7a5dd0c951ff2b8ac0b2509364131f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need a locking mechanism to protect the hardware SYSTIME register
which is split over 2 values, and has internal hardware latching. We
can't allow multiple accesses at the same time. However....
The spinlock_t is overkill here, especially use of spin_lock_irqsave,
since every PTP access will halt hardirqs. Notice that the only places
which need the SYSTIME value are user context and are capable of sleeping.
Thus, it is safe to use a mutex here instead of the spinlock.
Change-ID: I971761a89b58c6aad953590162e85a327fbba232
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We determine that a VSI is in vlan_mode whenever it has any filters
with a VLAN other than -1 (I40E_VLAN_ALL). The previous method of doing
so was to perform a loop whenever we needed the check. However, we can
notice that only place where filters are added (i40e_add_filter) can
change the condition from false to true, and the only place we can
return to false is in i40e_vsi_sync_filters_subtask. Thus, we can remove
the loop and use a boolean directly.
Doing this avoids looping over filters repeatedly especially while we're
already inside a loop over all the filters. This should reduce the
latency of filter operations throughout the driver.
Change-ID: Iafde08df588da2a2ea666997d05e11fad8edc338
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the mac_filter_list with a static size hash table of 8bits. The
primary advantage of this is a decrease in latency of operations related
to searching for specific MAC filters, including .set_rx_mode. Using
a linked list resulted in several locations which were O(n^2). Using
a hash table should give us latency growth closer to O(n*log(n)).
Change-ID: I5330bd04053b880e670210933e35830b95948ebb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
The kernel provides __dev_uc_sync and __dev_mc_sync in order for drivers
which need individual notification of add and delete for each filter.
These functions allow us to vastly simplify our .set_rx_mode handler. We
need to implement two functions for sync and unsync which add and remove
filters respectively.
This change avoids a very complex and inefficient algorithm which
resulted in an abnormal latency for the .set_rx_mode NDO operation. The
resulting code after this change is more readable, more efficient, and
less code.
Due to the callback signature used by these functions we also must
update several other functions to take a const u8 * pointer.
Change-Id: I2ca7fd4e10c0c07ed2291db1ea41bf5987fc6474
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally the is_vf and is_netdev fields were added in order to
distinguish between VF and netdev filters in a single VSI. However, it
can be noted that we use separate VSI for SRIOV VFs and for netdev VSI.
Thus, since a single VSI should only ever have one type of filter, we
can simply remove the checks and remove the typing.
In a similar fashion, we can note that the only remaining way to get
multiple filters of a single type is through a debug command that was
added to debugfs. This command is useless in practice, and results in
causing bugs if we keep counter tracking but lose the is_vf and
is_netdev protections as desired above.
Since the only time we'd actually have a counter value besides 0 and
1 is through use of this debugfs hook, we can remove this unnecessary
command, and the entire counter logic it required.
We vastly simplify mac filters by removing
(a) the distinction between VF and netdev filters
(b) counting logic
(c) the ability to add and remove filters bypassing the stack via debugfs
Change-ID: Idf916dd2a1159b1188ddbab5bef6b85ea6bf27d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
There exists a bug in which a 'perfect storm' can occur and cause
interrupts to fail to be correctly affinitized. This causes unexpected
behavior and has a substantial impact on performance when it happens.
The bug occurs if there is heavy traffic, any number of CPUs that have
an i40e interrupt are pegged at 100%, and the interrupt afffinity for
those CPUs is changed. Instead of moving to the new CPU, the interrupt
continues to be polled while there is heavy traffic.
The bug is most readily realized as the driver is first brought up and
all interrupts start on CPU0. If there is heavy traffic and the
interrupt starts polling before the interrupt is affinitized, the
interrupt will be stuck on CPU0 until traffic stops. The bug, however,
can also be wrought out more simply by affinitizing all the interrupts
to a single CPU and then attempting to move any of those interrupts off
while there is heavy traffic.
This patch fixes the bug by registering for update notifications from
the kernel when the interrupt affinity changes. When that fires, we
cache the intended affinity mask. Then, while polling, if the cpu is
pegged at 100% and we failed to clean the rings, we check to make sure
we have the correct affinity and stop polling if we're firing on the
wrong CPU. When the kernel successfully moves the interrupt, it will
start polling on the correct CPU. The performance impact is minimal
since the only time this section gets executed is when performance is
already compromised by the CPU.
Change-ID: I4410a880159b9dba1f8297aa72bef36dca34e830
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function is not used so there is no need to carry it forward. I have
plans to add a slightly different function that can be inlined to handle
the same kind of functionality.
Change-ID: Ie2dfcb189dc75e5fbc156bac23003e3b4210ae0f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
in commit a036244c06 a fix
was put into place to avoid a kernel panic when a non-
supported traffic class configuration was put into place
and then lldp was enabled/disabled on the link partner
switch. This fix caused it to be necessary to
unload/reload the driver to reenable DCB once a supported
TC config was in place.
The root cause of the original panic was that the function
i40e_pf_get_default_tc was allowing for a default TC other
than TC 0, and only TC 0 is supported as a default.
This patch removes the get_default_tc function and replaces
it with a #define since there is only one TC supported as
a default.
Change-Id: I448371974e946386d0a7718d73668b450b7c72ef
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This interface was only ever meant for debug only. Since it is not
supposed to be here we are removing it.
Change-ID: Id771a1e5e7d3e2b4b7f56591b61fb48c921e1d04
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch increases minimum number of allocated VSIs, so as to resolve
failure adding VSI for VF when 64-VFs assigned to a PF. The driver
supports up to 128 VFs per device, users can decide to enable up to
64-VFs on a single PF, especially 2 X 40 devices. In that scenario, with
VMDq co-existence, there would be starvation of VSIs - with this patch,
supported features would have enough VSIs for configuration now.
Change-ID: If084f4cd823667af8fe7fdc11489c705b32039d5
Signed-off-by: Akeem Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, when using ethtool to change the RSS hash key, ethtool would
report back saying the old key was still being used and no error was
reported. It was unclear whether it was being reported incorrectly or
being set incorrectly. Debugging revealed 'i40e_set_rxfh()' returned
zero immediately instead of setting the key because a user defined
indirection table is not supplied when changing the hash key.
This fix instead changes it such that if an indirection table is not
supplied, then a default one is created and the hash key is now
correctly set.
Change-ID: Iddb621897ecf208650272b7ee46702cad7b69a71
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.
Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Use __stringify instead.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements a feature change which allows using ethtool to set
RSS hash opts using less than four parameters if desired.
Change-ID: I0fbb91255d81e997c456697c21ac39cc9754821b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Properly track filter adds and deletes so the driver doesn't lose filters
during resets and up/down cycles. Add a tracking mechanism so that the
driver knows when to enter and leave promiscuous mode.
Implement a simple state machine so the driver can track the status of
each filter throughout its lifecycle. Properly manage the overflow promiscuous
state for the each VSI, and provide a way for the driver to detect when to exit
overflow promiscuous mode.
Remove all possible default MAC filters that the firmware may have set up so
that the driver can manage these correctly, particularly when VLANs come into
play. Remove the LAA flag for filters; instead just send whatever we get through
set_mac to the firmware as the LAA for wakeup purposes.
Finally, add the state of each filter to debugfs output so we can see what's
going on inside the driver's pointy little head.
Change-ID: I97c5e366fac2254fa01eaff4f65c0af61dcf2e1f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On systems with 128 CPUs, turning off TSO results in errors,
i40e 0000:03:00.0: failed to get tracking for 1 vectors for VSI 400, err=-12
i40e 0000:03:00.0: Couldn't create FDir VSI
i40e 0000:03:00.0: i40e_ptp_init: PTP not supported on eth0
i40e 0000:03:00.0: couldn't add VEB, err I40E_ERR_ADMIN_QUEUE_ERROR aq_err I40E_AQ_RC_ENOENT
i40e 0000:03:00.0: rebuild of switch failed: -1, will try to set up simple PF connection
i40e 0000:03:00.0 eth0: adding 00:10:e0:8a:24:b6 vid=0
Enabling FD_SB without checking availability of MSI-X vector is the
root cause. This change adds necessary check.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add flag to tell firmware to disable link on all ports.
This patch changes the bits set for telling firmware the PHY needs
to be modified by driver. Without this patch, the setting will only
set that mode for the current port on the device. Because the
MDIO interface is common for the copper device. The command needs to
set the mode for all ports.
Change-ID: I8baa7da91d384291ac95b41ae1a516604f8eb67f
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a 16 byte descriptor for receive, but the
driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole
lot of complexity while getting rid of the code.
Also since the previous patch made us use no-split mode all the
time, drop any support in the driver for any other value in dtype
and assume it is always zero (aka no-split).
Hooray for code removal!
Change-ID: I2257e902e4dad84a07b94db6d2e6f4ce69b27bc0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is part 1 of the Rx refactor series, just including
changes to i40e.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split
Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was all over the place using signed or unsigned types
for vf_id, when it should always be signed.
This fixes warnings of type unsafe comparisons from gcc with W=2.
Change-Id: I2cb681f83d0f68ca124d2e4131e4ac0d9f8a6b22
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the duplicate definition of I40E_MAX_USER_PRIORITY
in i40e.h that is not needed.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects
the net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular interest
here is that we have left the driver in staging since it still has an
API that people object to. Intel is working on a fix, but getting
these patches in now helps keep me sane as the upstream and Intel's
trees were over 300 patches apart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW8HR9AAoJELgmozMOVy/dDYMP+wSBALhIdV/pqVzdLCGfIUbK
H5agonm/3b/Oj74W30w2JYqXBFfZC2LGVJy6OwocJ3wK04v/KfZbA9G+QsOuh2hQ
Db+tFn1eoltvzrcx3k/a7x6zHGC4YyxyH9OX2B3QfRsNHeE7PG9KGp5dfEs2OH1r
WGp3jMLAsHf7o8uKpa0jyTEUEErATaTlG+YoaJ+BGHwurgCNy8ni+wAn+EAFiJ3w
iEJhcXB6KY69vkLsrLYuT9xxJn4udFJ3QEk8xdPkpLKsu+6Ue5i/eNQ19VfbpZgR
c6fTc8genfIv5S+fis+0P44u1oA7Kl2JT6IZYLi35gJ60ZmxTD+7GruWP3xX/wJ2
zuR3sTj5fjcFWenk087RSIU/EK87ONPD4g9QPdZpf3FtgleTVKk3YDlqwjqf8pgv
cO6gQ1BcOBnixJvhjNFiX1c2hvNhb3CkgObly1JBwhcCzZhLkV7BNFPbZuDHAeAx
VqzNEUse4hupkgiiuiGgudcJ4fsSxMW37kyfX9QC/qyk6YVuUDbrekcWI+MAKot7
5e5dHqFExpbn1Zgvc8yfvh88H2MUQAgaYwjanWF/qpppOPRd01nTisVQIOJn7s5C
arcWzvocpQe0GL2UsvDoWwAABXznL3bnnAoCyTWOES2RhOOcw0Ibw46Jl8FQ8gnl
2IRxQ+ltNEscb2cwi5wE
=t2Ko
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
This patch adds a Client interface for i40iw driver
support. Also expands the Virtchannel to support messages
from i40evf driver on behalf of i40iwvf driver.
This client API is used by the i40iw and i40iwvf driver
to access the core driver resources brokered by the i40e driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's. Without this
patch, the blink led functionality fails on some parts. This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.
Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed mapping of SEID is removed from specification. Hence
this patch removes code which was using hard coded base VEB SEID.
Changed FCoE code to use "hw->pf_id" to obtain correct "idx"
and verified.
Removed defines for BASE VSI/VEB SEID and BASE_PF_SEID since it
is not used anymore.
Change-ID: Id507cf4b1fae1c0145e3f08ae9ea5846ea5840de
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While re-enabling interrupts the driver would clear all pending
causes. This meant that if an interrupt was generated while the driver
was cleaning or polling with interrupts disabled, then that interrupt
was lost. This could cause a queue to become dead, especially for
receive. Refactored the enable_icr0 function in order to allow
it to be decided by the caller whether the CLEARPBA (clear pending
events) bit will be set while re-enabling the interrupt.
Also update copyright year in file headers.
Change-ID: Ic1db100a05e13c98919057696db147a258ca365a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the DCB firmware version related checks specific to
X710 and XL710 only. These checks are not required for
X722 family of devices.
Introduced an inline routine to help determine if the
MAC type is X710/XL710 or not.
Moved the firmware version related checks in i40e_sw_init()
and defined flags for different cases
Fix the version check to allow using "Set LLDP MIB" AQ
for beyond FVL4 FW releases.
Change-ID: Ib78288343de983aa0354fc28aa36e99b073662c0
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X722 can support automatic rule eviction for automatically added
flow director rules. Feature is (should be) disabled by default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-02-16
This series contains updates to i40e/i40evf only.
Shannon adds flags to MAC allocation requests to signify that the MAC VLAN
filters should come from the shared resource pool. Added a new "set switch
config" admin queue command and the new Cisco VXLAN-GPE cloud tunnel type
for the admin queue commands. Added more detail to the NVM update debug
message in order to see the full ethtool request data. Also added a few
more bits of netdev data into the debugfs output for dump VSI.
Pandi fixes the width of two datatypes which were being declared a different
size from what they are assigned.
Anjali fixes an issue where we were not doing write-back on interrupt
throttle for legacy case in x722.
Mitch adds a counter for ARQ overflows since sometimes an ever-growing
number indicates that something bad is happening. Also added 20G speed for
Tx bandwidth calculations.
Jesse refactors the DCB function based on a community suggestion to change
the multi-level if statement into a switch statement. Cleans up VF device
IDs in the PF, since it does not need to know them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, ARQ overflows are a big deal and tell us that the
firmware/hardware/driver/something is having problems. But normally
they're no big deal. To assist in assessing this, add a counter to
our Ethtool stats. A handful of ARQ overflows during VF init is no
problem. A large, ever-growing number indicates that Something Bad is
happening.
Change-ID: Ie5348bfbc8a54a890559cb00279c28d976a55096
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The restart-autoneg work around does not apply to X722.
Added a flag to set it only for the right MAC and right FW version
where the work around should be applied.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Change-ID: I942c3ff40cccd1e56f424b1da776b020fe3c9d2a
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
100M SGMII is only supported on X722. Replace the mac check with
a feature flag check that is only set for the X722 device.
Change-ID: I53452d9af6af8cd9dca8500215fbc6ce93418f52
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the i40e equivalent of commit c762dff24c ("ixgbe: Look up MAC
address in Open Firmware or IDPROM").
As with that fix, attempt to look up the MAC address in Open Firmware
on systems that support it, and use IDPROM on SPARC if no OF address
is found.
In the case of the i40e there is an assumption that the default mac
address has already been set up as the primary mac filter on probe,
so if this filter is obtained from the Open Firmware or IDPROM, an
explicit write is needed via i40e_aq_mac_address_write() and
i40e_aq_add_macvlan() invocation.
The I40E_FLAG_PF_MAC flag in the platform-private i40e_pf structure
tracks whether a platform-specific mac address was found, in which
case calls to i40e_aq_mac_address_write() and i40e_aq_add_macvlan()
will be triggered.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 8fe269991a.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.
v2: Add a signed-off-by.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harshitha Ramamurthy