Fix build error when !CONFIG_CPU_FREQ
drivers/gpu/drm/tilcdc/tilcdc_drv.c: In function 'tilcdc_load':
drivers/gpu/drm/tilcdc/tilcdc_drv.c:327:1: error: label 'fail_put_clk' defined but not used [-Werror=unused-label]
fail_put_clk:
^
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There is nothing special about tilcdc HW when the video memory is
concerned. Just using the standard drm helpers for implementation is
enough.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The LCD controller must be deactivated and all DMA transactions stopped
when the suspend power state is entered otherwise the PRCM causes the L3
bus to get stuck in transition state.
This commit forces the lcdc to be shut down and waits for all pending DMA
transactions to complete as part of the suspend handler for this driver.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The frame_done interrupt was only being enabled when the vsync
interrupts were being enabled by DRM. However the frame_done is
used to determine if the LCD controller has successfully completed
the raster_enable, raster_disable commands and the vsync interrupts
are not always enabled during these operations.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On BeagleBone Black if no HDMI monitor is connected and suspend
is requested a kernel panic will result:
root@am335x-evm:~# echo mem > /sys/power/state
[ 65.548710] PM: Syncing filesystems ... done.
[ 65.631311] Freezing user space processes ... (elapsed 0.006 seconds) done.
[ 65.648619] Freezing remaining freezable tasks ... (elapsed 0.005 seconds) done.
[ 65.833500] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa30e004
[ 65.841692] Internal error: : 1028 [#1] SMP ARM
<snip>
[ 66.105287] [<c03765f0>] (platform_pm_suspend) from [<c037b6d4>] (dpm_run_callback+0x34/0x70)
[ 66.114370] [<c037b6d4>] (dpm_run_callback) from [<c037ba84>] (__device_suspend+0x10c/0x2f4)
[ 66.123357] [<c037ba84>] (__device_suspend) from [<c037d004>] (dpm_suspend+0x58/0x218)
[ 66.131796] [<c037d004>] (dpm_suspend) from [<c008d948>] (suspend_devices_and_enter+0x9c/0x3c0)
[ 66.141055] [<c008d948>] (suspend_devices_and_enter) from [<c008de7c>] (pm_suspend+0x210/0x24c)
[ 66.150312] [<c008de7c>] (pm_suspend) from [<c008cabc>] (state_store+0x68/0xb8)
[ 66.158103] [<c008cabc>] (state_store) from [<c02e9654>] (kobj_attr_store+0x14/0x20)
[ 66.166355] [<c02e9654>] (kobj_attr_store) from [<c0185c70>] (sysfs_kf_write+0x4c/0x50)
[ 66.174883] [<c0185c70>] (sysfs_kf_write) from [<c018926c>] (kernfs_fop_write+0xb4/0x150)
[ 66.183598] [<c018926c>] (kernfs_fop_write) from [<c0122638>] (vfs_write+0xa8/0x180)
[ 66.191846] [<c0122638>] (vfs_write) from [<c01229f8>] (SyS_write+0x40/0x8c)
[ 66.199365] [<c01229f8>] (SyS_write) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 66.207426] Code: e595c210 e5932000 e59cc000 e08c2002 (e592c000)
This is because the lcdc module is not enabled when no monitor is detected
to save power. However the suspend handler just blindly tries to save the
lcdc state by copying out the pertinent registers. However module is off
so no good things happen when you try and access it.
This patch only saves off the registers if the module is enabled, and
then only restores the registers on resume if they were saved off during
suspend.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Update tilcdc driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
LCDC hardware does not support fb pitch that is different (i.e. larger)
than the screen size. The driver currently does no checks for this, and
the results of too big pitch are are flickering and lower fps.
This issue easily happens when using libdrm's modetest tool with non-32
bpp modes. As modetest always allocated 4 bytes per pixel, it implies a
bigger pitch for 16 or 24 bpp modes.
This patch adds a check to reject pitches the hardware cannot support.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Updating the tilcdc DRM driver code to calculate the LCD controller
pixel clock more accurately. Based on a suggested implementation by
Tomi Valkeinen.
The current code does not work correctly and produces wrong results
with many requested clock rates. It also oddly uses two different
clocks, a display pll clock and a divider clock (child of display
pll), instead of just using the clock coming to the lcdc.
This patch removes the use of the display pll clock, and rewrites the
code to calculate the clock rates. The idea is simply to request a
clock rate of pixelclock*2, as the LCD controller has an internal
divider which we set to 2.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
[Rewrapped description]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
First drm-misc pull req for 4.6. Big one is the drm_event cleanup, which
is also prep work for adding android fence support to kms (Gustavo is
planning to do that). Otherwise random small bits all over.
* tag 'topic/drm-misc-2016-02-08' of git://anongit.freedesktop.org/drm-intel: (33 commits)
gma500: clean up an excessive and confusing helper
drm/gma500: remove helper function
drm/vmwgfx: Nuke preclose hook
drm/vc4: Nuke preclose hook
drm/tilcdc: Nuke preclose hook
drm/tegra: Stop cancelling page flip events
drm/shmob: Nuke preclose hook
drm/rcar: Nuke preclose hook
drm/omap: Nuke close hooks
drm/msm: Nuke preclose hooks
drm/imx: Unconfuse preclose logic
drm/exynos: Remove event cancelling from postclose
drm/atmel: Nuke preclose
drm/i915: Nuke intel_modeset_preclose
drm: Nuke vblank event file cleanup code
drm: Clean up pending events in the core
drm/vblank: Use drm_event_reserve_init
drm/vmwgfx: fix a NULL dereference
drm/crtc-helper: Add caveat to disable_unused_functions doc
drm/gma500: Remove empty preclose hook
...
Again since the drm core takes care of event unlinking/disarming this
is now just needless code.
v2: Fixup misplaced hunks.
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-13-git-send-email-daniel.vetter@ffwll.ch
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The drm_fbdev_cma_init function always calls the
drm_helper_disable_unused_functions. Since it's part of the usual probe
process, all the drivers using that helper will end up having their encoder
and CRTC disable functions called at probe if their device has not been
reported as enabled.
This could be fixed by reading out from the registers the current state of
the device if it is enabled, but even that will not handle the case where
the device is actually disabled.
Moreover, the drivers using the atomic modesetting expect that their enable
and disable callback to be called when the device is already enabled or
disabled (respectively).
We can however fix this issue by moving the call to
drm_helper_disable_unused_functions out of drm_fbdev_cma_init and make the
drivers needing it (all the drivers calling drm_fbdev_cma_init and not
using the atomic modesetting) explicitly call it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452785109-6172-14-git-send-email-maxime.ripard@free-electrons.com
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
Drivers shouldn't clobber the passed in addfb ioctl parameters.
i915 was doing just that. To prevent it from happening again,
pass the struct around as const, starting all the way from
internal_framebuffer_create().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_count() returns the software counter. We should not pretend
it's the hw counter since we use the hw counter to figuere out what the
software counter value should be. So instead provide a new function
drm_vblank_no_hw_counter() for drivers that don't have a real hw
counter. The new function simply returns 0, which is about the only
thing it can do.
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
[danvet: s/int pipe/unsigned int pipe/ to follow Thierry's interface
change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Furthermore there is devm_gpiod_get_optional which is designed to get
optional gpios.
Simplify driver accordingly.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Adds a CONFIG_DRM_TILCDC_SLAVE_COMPAT module for "ti,tilcdc,slave"
node conversion. The implementation is in tilcdc_slave_compat.c and it
uses tilcdc_slave_compat.dts as a basis for creating a DTS
overlay. The DTS overlay adds an external tda998x encoder to tilcdc
that corresponds to the old tda998x based slave encoder.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
tilcdc calls runtime PM get/put functions everywhere. Some of those
places will be called in irq context, crashing the driver.
As a quick fix, use pm_runtime_irq_safe() for tilcdc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Add support for an external compontised DRM encoder. The external
encoder can be connected to tilcdc trough device tree graph binding.
The binding document for tilcdc has been updated. The current
implementation supports only tda998x encoder.
To be able to filter out the unsupported video modes the tilcdc driver
needs to hijack the external connectors helper functions. The tilcdc
installes new helper functions that are otherwise identical to
orignals, but the mode_valid() call-back check the mode first localy,
before calling the original call-back. The tilcdc dirver restores the
original helper functions before it is unbound from the external
device.
I got the idea and some lines of code from Jean-Francois Moine's
"drm/tilcdc: Change the interface with the tda998x driver"-patch.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove tilcdc slave support for tda998x driver. The tilcdc slave
support would conflicts with componentized use of tda998x.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Force crtc dpms off before destroying the crtc instead of just
checking the dpms state. This fixes warning message and frozen picture
after tilcdc module unloading.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRM_GEM_CMA_HELPER is depend on HAVE_DMA_ATTRS, or it will break the
building. The related error (with allmodconfig under xtensa):
CC [M] drivers/gpu/drm/drm_gem_cma_helper.o
drivers/gpu/drm/drm_gem_cma_helper.c: In function 'drm_gem_cma_create':
drivers/gpu/drm/drm_gem_cma_helper.c:110:19: error: implicit declaration of function 'dma_alloc_writecombine' [-Werror=implicit-function-declaration]
cma_obj->vaddr = dma_alloc_writecombine(drm->dev, size,
^
drivers/gpu/drm/drm_gem_cma_helper.c:110:17: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
cma_obj->vaddr = dma_alloc_writecombine(drm->dev, size,
^
drivers/gpu/drm/drm_gem_cma_helper.c: In function 'drm_gem_cma_free_object':
drivers/gpu/drm/drm_gem_cma_helper.c:193:3: error: implicit declaration of function 'dma_free_writecombine' [-Werror=implicit-function-declaration]
dma_free_writecombine(gem_obj->dev->dev, cma_obj->base.size,
^
drivers/gpu/drm/drm_gem_cma_helper.c: In function 'drm_gem_cma_mmap_obj':
drivers/gpu/drm/drm_gem_cma_helper.c:330:8: error: implicit declaration of function 'dma_mmap_writecombine' [-Werror=implicit-function-declaration]
ret = dma_mmap_writecombine(cma_obj->base.dev->dev, vma,
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
The drm_fbdev_cma_hotplug_event() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that we're using lists instead of kfifo to store drm flip-work tasks
we do not need the size parameter passed to drm_flip_work_init function
anymore.
Moreover this function cannot fail anymore, we can thus remove the return
code.
Modify drm_flip_work_init users to take account of these changes.
[airlied: fixed two unused variable warnings]
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just a bit of OCD cleanup on headers - this function isn't the core
interface any more but just a helper for drivers who haven't yet
transitioned to universal planes. Put the declaration at the right
spot and sprinkle necessary #includes over all drivers.
Maybe this helps to encourage driver maintainers to do the switch.
v2: Fix #include ordering for tegra, reported by 0-day builder.
v3: Include required headers, reported by Thierry.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In order to support the "enable GPIO" available in many panel devices,
this commit adds a proper devicetree binding.
By providing an enable GPIO in the devicetree, the driver can now turn
off and on the panel device, and/or the backlight device. Both the
backlight and the GPIO are optional properties.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of setting an initial value for the return code, set it explicitly
on each error path. This is just a cosmetic cleanup, as preparation for the
enable GPIO support.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current backlight support is broken; the driver expects a backlight-class
in the panel devicetree node. Fix this by implementing it properly, getting
an optional backlight from a phandle.
This shouldn't cause any backward-compatibility DT issue because the current
implementation doesn't work and is not even documented.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Using the managed variant to allocate the resource makes the code simpler
and less error-prone.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just a cosmetic cleanup.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just a trivial cleanup to remove the variable.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds the missing calls to of_node_put to release the node
that's currently held by the of_get_child_by_name() call in the panel
info parsing code.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current error path calls tilcdc_unload() in case of an error to release
the resources. However, this is wrong because not all resources have been
allocated by the time an error occurs in tilcdc_load().
To fix it, this commit adds proper labels to bail out at the different
stages in the load function, and release only the resources actually allocated.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 34ea3d3863 ("drm: add register and unregister functions
for connectors") probably missed out converting the
drm_sysfs_connector_remove instances in the following files.
Without this patch we get the following compilation error:
ERROR: "drm_sysfs_connector_remove" [drivers/gpu/drm/tilcdc/tilcdc.ko] undefined!
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
CC: Thomas Wood <thomas.wood@intel.com>
CC: David Herrmann <dh.herrmann@gmail.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use module_init instead of late_initcall, as is the norm for modular
drivers.
module_init was used until 6e8de0bd6a
("drm/tilcdc: add encoder slave (v2)") changed it to a late_initcall,
but it does not explain why. Tests show it's working properly with
module_init.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The TI tilcdc driver is designed with a notion of submodules. Currently,
at unload time, these submodules are iterated and destroyed.
Now that the tilcdc remove order is fixed, this can be handled perfectly
by the kernel using the device infrastructure, since each submodule
is a kernel driver itself, and they are only destroy()'ed at unload
time. Therefore we move the destroy() functionality to each submodule's
remove().
Also, remove some checks in the unloading process since the new code
guarantees the resources are allocated and need a release.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
display_timings_release calls kfree on the display_timings object passed
to it. Calling kfree after it is wrong. SLUB debug showed the following
warning:
=============================================================================
BUG kmalloc-64 (Tainted: G W ): Object already free
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in of_get_display_timings+0x2c/0x214 age=601 cpu=0
pid=884
__slab_alloc.constprop.79+0x2e0/0x33c
kmem_cache_alloc+0xac/0xdc
of_get_display_timings+0x2c/0x214
panel_probe+0x7c/0x314 [tilcdc]
platform_drv_probe+0x18/0x48
[..snip..]
INFO: Freed in panel_destroy+0x18/0x3c [tilcdc] age=0 cpu=0 pid=907
__slab_free+0x34/0x330
panel_destroy+0x18/0x3c [tilcdc]
tilcdc_unload+0xd0/0x118 [tilcdc]
drm_dev_unregister+0x24/0x98
[..snip..]
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unregister resources in the correct order on tilcdc_drm_fini, which is
the reverse order they were registered during tilcdc_drm_init.
This also means unregistering the driver before releasing its resources.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
The driver did not unregister the allocated framebuffer, which caused
memory leaks (and memory manager WARNs) when unloading. Also, the
framebuffer device under /dev still existed after unloading.
Add a call to drm_fbdev_cma_fini when unloading the module to prevent
both issues.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a drm_sysfs_connector_remove call when we destroy the panel to make
sure the connector node in sysfs gets deleted.
This is required for proper unload and re-load of this driver, otherwise
we will get a warning about a duplicate filename in sysfs.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a drm_sysfs_connector_remove call when we destroy the panel to make
sure the connector node in sysfs gets deleted.
This is required for proper unload and re-load of this driver as a
module. Without this, we would get a warning at re-load time like so:
tda998x 0-0070: found TDA19988
------------[ cut here ]------------
WARNING: CPU: 0 PID: 825 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x54/0x74()
sysfs: cannot create duplicate filename '/class/drm/card0-HDMI-A-1'
Modules linked in: [..]
CPU: 0 PID: 825 Comm: modprobe Not tainted 3.15.0-rc4-00027-g9dcdef4 #82
[<c0013bb8>] (unwind_backtrace) from [<c0011824>] (show_stack+0x10/0x14)
[<c0011824>] (show_stack) from [<c0034e8c>] (warn_slowpath_common+0x68/0x88)
[<c0034e8c>] (warn_slowpath_common) from [<c0034edc>] (warn_slowpath_fmt+0x30/0x40)
[<c0034edc>] (warn_slowpath_fmt) from [<c01243f4>] (sysfs_warn_dup+0x54/0x74)
[<c01243f4>] (sysfs_warn_dup) from [<c0124708>] (sysfs_do_create_link_sd.isra.2+0xb0/0xb8)
[<c0124708>] (sysfs_do_create_link_sd.isra.2) from [<c02ae37c>] (device_add+0x338/0x520)
[<c02ae37c>] (device_add) from [<c02ae6e8>] (device_create_groups_vargs+0xa0/0xc4)
[<c02ae6e8>] (device_create_groups_vargs) from [<c02ae758>] (device_create+0x24/0x2c)
[<c02ae758>] (device_create) from [<c029b4ec>] (drm_sysfs_connector_add+0x64/0x204)
[<c029b4ec>] (drm_sysfs_connector_add) from [<bf0b1b40>] (slave_modeset_init+0x120/0x1bc [tilcdc])
[<bf0b1b40>] (slave_modeset_init [tilcdc]) from [<bf0b2be8>] (tilcdc_load+0x214/0x4c0 [tilcdc])
[<bf0b2be8>] (tilcdc_load [tilcdc]) from [<c029955c>] (drm_dev_register+0xa4/0x104)
[..snip..]
---[ end trace 4df8d614936ebdee ]---
[drm:drm_sysfs_connector_add] *ERROR* failed to register connector device: -17
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a drm_sysfs_connector_remove call when we destroy the panel to make
sure the connector node in sysfs gets deleted.
This is required for proper unload and re-load of this driver as a
module. Without this, we would get a warning at re-load time like so:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 824 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x54/0x74()
sysfs: cannot create duplicate filename '/class/drm/card0-LVDS-1'
Modules linked in: [...]
CPU: 0 PID: 824 Comm: modprobe Not tainted 3.15.0-rc4-00027-g6484f96-dirty #81
[<c0013bb8>] (unwind_backtrace) from [<c0011824>] (show_stack+0x10/0x14)
[<c0011824>] (show_stack) from [<c0034e8c>] (warn_slowpath_common+0x68/0x88)
[<c0034e8c>] (warn_slowpath_common) from [<c0034edc>] (warn_slowpath_fmt+0x30/0x40)
[<c0034edc>] (warn_slowpath_fmt) from [<c01243f4>] (sysfs_warn_dup+0x54/0x74)
[<c01243f4>] (sysfs_warn_dup) from [<c0124708>] (sysfs_do_create_link_sd.isra.2+0xb0/0xb8)
[<c0124708>] (sysfs_do_create_link_sd.isra.2) from [<c02ae37c>] (device_add+0x338/0x520)
[<c02ae37c>] (device_add) from [<c02ae6e8>] (device_create_groups_vargs+0xa0/0xc4)
[<c02ae6e8>] (device_create_groups_vargs) from [<c02ae758>] (device_create+0x24/0x2c)
[<c02ae758>] (device_create) from [<c029b4ec>] (drm_sysfs_connector_add+0x64/0x204)
[<c029b4ec>] (drm_sysfs_connector_add) from [<bf0b1fec>] (panel_modeset_init+0xb8/0x134 [tilcdc])
[<bf0b1fec>] (panel_modeset_init [tilcdc]) from [<bf0b2bf0>] (tilcdc_load+0x214/0x4c0 [tilcdc])
[<bf0b2bf0>] (tilcdc_load [tilcdc]) from [<c029955c>] (drm_dev_register+0xa4/0x104)
[ .. snip .. ]
---[ end trace b2d09cd9578b0497 ]---
[drm:drm_sysfs_connector_add] *ERROR* failed to register connector device: -17
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Darren Etheridge <detheridge@ti.com>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.
With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
This was hidden in a generic void * dev->mm_private. But only ever
used for gem. But thanks to this fake generic pretension no one
noticed that Rob's drm drivers are now all broken.
So just give the offset manager a type pointer and fix up msm, omapdrm
and tilcdc.
v2: Fixup compile fail.
v3: Fixup rebase fail that David spotted.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
tilcdc already stores the drm_device in the driver data pointer. So
use that.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm tree changes from Dave Airlie:
"This is the main drm pull request, I have some overlap with sound and
arm-soc, the sound patch is acked and may conflict based on -next
reports but should be a trivial fixup, which I'll leave to you!
Highlights:
- new drivers:
MSM driver from Rob Clark
- non-drm:
switcheroo and hdmi audio driver support for secondary GPU
poweroff, so drivers can use runtime PM to poweroff the GPUs. This
can save 5 or 6W on some optimus laptops.
- drm core:
combined GEM and TTM VMA manager
per-filp mmap permission tracking
initial rendernode support (via a runtime enable for now, until we get api stable),
remove old proc support,
lots of cleanups of legacy code
hdmi vendor infoframes and 4k modes
lots of gem/prime locking and races fixes
async pageflip scaffolding
drm bridge objects
- i915:
Haswell PC8+ support and eLLC support, HDMI 4K support, initial
per-process VMA pieces, watermark reworks, convert to generic hdmi
infoframes, encoder reworking, fastboot support,
- radeon:
CIK PM support, remove 3d blit code in favour of DMA engines,
Berlin GPU support, HDMI audio fixes
- nouveau:
secondary GPU power down support for optimus laptops, lots of
fixes, use MSI, VP3 engine support
- exynos:
runtime pm support for g2d, DT support, remove non-DT,
- tda998x i2c driver:
lots of fixes for sync issues
- gma500:
lots of cleanups
- rcar:
add LVDS support, fbdev emulation,
- tegra:
just minor fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (684 commits)
drm/exynos: Fix build error with exynos_drm_connector.c
drm/exynos: Remove non-DT support in exynos_drm_fimd
drm/exynos: Remove non-DT support in exynos_hdmi
drm/exynos: Remove non-DT support in exynos_drm_g2d
drm/exynos: Remove non-DT support in exynos_hdmiphy
drm/exynos: Remove non-DT support in exynos_ddc
drm/exynos: Make Exynos DRM drivers depend on OF
drm/exynos: Consider fallback option to allocation fail
drm/exynos: fimd: move platform data parsing to separate function
drm/exynos: fimd: get signal polarities from device tree
drm/exynos: fimd: replace struct fb_videomode with videomode
drm/exynos: check a pixel format to a particular window layer
drm/exynos: fix fimd pixel format setting
drm/exynos: Add NULL pointer check
drm/exynos: Remove redundant error messages
drm/exynos: Add missing of.h header include
drm/exynos: Remove redundant NULL check in exynos_drm_buf
drm/exynos: add device tree support for rotator
drm/exynos: Add missing includes
drm/exynos: add runtime pm interfaces to g2d driver
...
This lets drivers see the flags requested by the application
[airlied: fixup for rcar/imx/msm]
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a fixup function that will flip the hsync priority and
add a hskew value that is used to shift the tda998x to the
right by a variable number of pixels depending on the mode.
This works around an issue with the sync timings that tilcdc
is outputing.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Russell King <rmk_kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All the gem based kms drivers really want the same function to
destroy a dumb framebuffer backing storage object.
So give it to them and roll it out in all drivers.
This still leaves the option open for kms drivers which don't use GEM
for backing storage, but it does decently simplify matters for gem
drivers.
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Cc: Ben Skeggs <skeggsb@gmail.com>
Reviwed-by: Rob Clark <robdclark@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bits weren't cleared so resolution changes didn't work.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In certain senarios drm will initialize before i2c this means that i2c
slave devices like the nxp tda998x will fail to be probed. This patch
detects this condition then defers the probe of the slave device and
the tilcdc main driver.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
keeping checkpatch happy.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The tilcdc has a number of limitations for the allowed sizes of
the various adjustable timing parameter. Some modes are outside
of these timings. This commit will prune modes that report timings
that will overflow the allowed sizes in the tilcdc.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When hooking up to an HDMI analyzer noticed some timings were
off by one. Referring to the hardware technical reference manual
for the lcd controller some of the timing registers use 0 to
represent 1. This patch addresses that issue.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Adding support for max-pixelclock and max-width device tree
entries. As some devices that use the tilcdc hardware module
have restrictions on the allowed/tested values. Also update DT
bindings document to reflect new parameters.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
TI LCD controller version 2 has an extended eleventh
bit that enables horizontal resolutions greater than
1024 pixels to be specified (upto 2048). This patch
adds support for setting this bit on LCDC V2.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEbBAABAgAGBQJRxf9cAAoJEHm+PkMAQRiGMWkH911xM4gRmFgE7SqVW4F4AWBm
ngcqMqNy9IdqKfibORUUDvVfEa5gjD5ai2quIKpfQiaukbpQJ696H90ijuAkajLn
DQBrN243s0pzhhc/quWINnWxsFQ613JjdUMUMaD7e9A1aKjYzWrPGt/tSjrFXGCP
tArTupVzc/iOmnEQDKiROI/Nokq44QJ36aTGPM7n08xMtpKmkCXM+9/UosBteB0O
HVI33dmjwz7i55fI53XAWyuZCE+gSEnA4z8spJ9LfXso2W14V+roc+GuL6OyeeTI
pCn/+4niVPb4B0ROZlpyVmdZjbPPcMMEK5o+BSJI68SH6LHZTQh2iVuqYfpSyA==
=uUH5
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc7' into drm-next
Linux 3.10-rc7
The sdvo lvds fix in this -fixes pull
commit c3456fb3e4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jun 10 09:47:58 2013 +0200
drm/i915: prefer VBT modes for SVDO-LVDS over EDID
has a silent functional conflict with
commit 990256aec2
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri May 31 12:17:07 2013 +0000
drm: Add probed modes in probe order
in drm-next. W simply need to add the vbt modes before edid modes, i.e. the
other way round than now.
Conflicts:
drivers/gpu/drm/drm_prime.c
drivers/gpu/drm/i915/intel_sdvo.c
The preferred_bpp value in currently hard-coded to 16.
This causes color corruption on the am335x-evm lcd panel which
requires 32 bpp instead. This changes attempts to use the configured
bpp value from the DT or built-in panel-info struct.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Many of the drivers didn't implement palette/gamma handling, but were forced
to provide stubs for the hooks to avoid drm_fb_helper from oopsing. Now that
the hooks are optional, we can eliminate all the stubs.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
The dependecies for BACKLIGHT_CLASS_DEVICE are defined a bit
strange, but it seems one has to always select both BACKLIGHT_CLASS_DEVICE
and BACKLIGHT_LCD_SUPPORT to avoid this error:
drivers/gpu/drm/tilcdc/tilcdc_panel.c:396:
undefined reference to `of_find_backlight_by_node'
Cc: Rob Clark <robdclark@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 3.10.
Wierd bits:
- OMAP drm changes required OMAP dss changes, in drivers/video, so I
took them in here.
- one more fbcon fix for font handover
- VT switch avoidance in pm code
- scatterlist helpers for gpu drivers - have acks from akpm
Highlights:
- qxl kms driver - driver for the spice qxl virtual GPU
Nouveau:
- fermi/kepler VRAM compression
- GK110/nvf0 modesetting support.
Tegra:
- host1x core merged with 2D engine support
i915:
- vt switchless resume
- more valleyview support
- vblank fixes
- modesetting pipe config rework
radeon:
- UVD engine support
- SI chip tiling support
- GPU registers initialisation from golden values.
exynos:
- device tree changes
- fimc block support
Otherwise:
- bunches of fixes all over the place."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (513 commits)
qxl: update to new idr interfaces.
drm/nouveau: fix build with nv50->nvc0
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
...
The tilcdc driver fails to be built as a module because of extraneous
MODULE_DEVICE_TABLE entries:
drivers/gpu/drm/tilcdc/tilcdc_slave.o:(.data+0x54): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here
drivers/gpu/drm/tilcdc/tilcdc_panel.o:(.data+0x54): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here
drivers/gpu/drm/tilcdc/tilcdc_drv.o:(.data+0x184): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here
Since the entire point of these entries is to make the module autoload
when one of the devices is present, it's enough to keep the one entry
for "ti,am33xx-tilcdc", which should always be there if any of the
others are.
Acked-by: Rob Clark <robdclark@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes the following checkpatch error:
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Silences the following checkpatch warning:
WARNING: please, no space before tabs
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Silences the following checkpatch warning:
WARNING: braces {} are not necessary for any arm of this statement
if (priv->rev == 1) {
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When make with EXTRA_CFLAGS=-W, it will report error.
so give a check in Makefile.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of checking if num_encoders is zero, it is being assigned 0.
Convert the assignment to a check.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We currently have videomode_from_timing(), which takes one
display_timing entry from display_timings.
To make it easier to use display_timing without display_timings, this
patch renames videomode_from_timing() to videomode_from_timings(), and
adds a new videomode_from_timing() which just converts a given
display_timing to videomode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
This patch simplifies videomode related Kconfig and Makefile. After this
patch, there's only one non-user selectable Kconfig option left,
VIDEOMODE_HELPERS. The reasons for the change:
* Videomode helper functions are not something that should be shown in
the kernel configuration options. The related code should just be
included if it's needed, i.e. selected by drivers using videomode.
* There's no need to have separate Kconfig options for videomode and
display_timing. First of all, the amount of code for both is quite
small. Second, videomode depends on display_timing, and display_timing
in itself is not really useful, so both would be included in any case.
* CONFIG_VIDEOMODE is a bit vague name, and CONFIG_VIDEOMODE_HELPERS
describes better what's included.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[airlied: hack for now until we fix cma helpers on other OF platforms]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Add an output panel driver for LCD panels. Tested with LCD3 cape on
beaglebone.
v1: original
v2: s/of_find_node_by_name()/of_get_child_by_name()/ from Pantelis
Antoniou
v3: add backlight support
v4: rebase to latest of video timing helpers
v5: remove some unneeded fields from panel-info struct, add DT bindings
docs
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Add output panel driver for i2c encoder slaves.
v1: original
v2: add DT bindings docs, and minor updates for review comments
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
A simple DRM/KMS driver for the TI LCD Controller found in various
smaller TI parts (AM33xx, OMAPL138, etc). This driver uses the
CMA helpers. Currently only the TFP410 DVI encoder is supported
(tested with beaglebone + DVI cape). There are also various LCD
displays, for which support can be added (as I get hw to test on),
and an external i2c HDMI encoder found on some boards.
The display controller supports a single CRTC. And the encoder+
connector are split out into sub-devices. Depending on which LCD
or external encoder is actually present, the appropriate output
module(s) will be loaded.
v1: original
v2: fix fb refcnting and few other cleanups
v3: get +/- vsync/hsync from timings rather than panel-info, add
option DT max-bandwidth field so driver doesn't attempt to
pick a display mode with too high memory bandwidth, and other
small cleanups
v4: remove some unneeded stuff from panel-info struct, properly
set high bits for hfp/hsw/hbp for rev 2, add DT bindings docs
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
