We will never need more guest_msrs than there are indices in
vmx_msr_index. Thus, at present, the guest_msrs array will not exceed
168 bytes.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 37e4c997da ("KVM: VMX: validate individual bits of guest
MSR_IA32_FEATURE_CONTROL") broke the KVM_SET_MSRS ABI by instituting
new constraints on the data values that kvm would accept for the guest
MSR, IA32_FEATURE_CONTROL. Perhaps these constraints should have been
opt-in via a new KVM capability, but they were applied
indiscriminately, breaking at least one existing hypervisor.
Relax the constraints to allow either or both of
FEATURE_CONTROL_VMXON_ENABLED_OUTSIDE_SMX and
FEATURE_CONTROL_VMXON_ENABLED_INSIDE_SMX to be set when nVMX is
enabled. This change is sufficient to fix the aforementioned breakage.
Fixes: 37e4c997da ("KVM: VMX: validate individual bits of guest MSR_IA32_FEATURE_CONTROL")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If X86_FEATURE_RTM is disabled, the guest should not be able to access
MSR_IA32_TSX_CTRL. We can therefore use it in KVM to force all
transactions from the guest to abort.
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current guest mitigation of TAA is both too heavy and not really
sufficient. It is too heavy because it will cause some affected CPUs
(those that have MDS_NO but lack TAA_NO) to fall back to VERW and
get the corresponding slowdown. It is not really sufficient because
it will cause the MDS_NO bit to disappear upon microcode update, so
that VMs started before the microcode update will not be runnable
anymore afterwards, even with tsx=on.
Instead, if tsx=on on the host, we can emulate MSR_IA32_TSX_CTRL for
the guest and let it run without the VERW mitigation. Even though
MSR_IA32_TSX_CTRL is quite heavyweight, and we do not want to write
it on every vmentry, we can use the shared MSR functionality because
the host kernel need not protect itself from TSX-based side-channels.
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When L1 guest uses 5-level paging, it fails vm-entry to L2 due to
invalid host-state. It needs to add CR4_LA57 bit to nested CR4_FIXED1
MSR.
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The L1 hypervisor may include the IA32_TIME_STAMP_COUNTER MSR in the
vmcs12 MSR VM-exit MSR-store area as a way of determining the highest
TSC value that might have been observed by L2 prior to VM-exit. The
current implementation does not capture a very tight bound on this
value. To tighten the bound, add the IA32_TIME_STAMP_COUNTER MSR to the
vmcs02 VM-exit MSR-store area whenever it appears in the vmcs12 VM-exit
MSR-store area. When L0 processes the vmcs12 VM-exit MSR-store area
during the emulation of an L2->L1 VM-exit, special-case the
IA32_TIME_STAMP_COUNTER MSR, using the value stored in the vmcs02
VM-exit MSR-store area to derive the value to be stored in the vmcs12
VM-exit MSR-store area.
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename function find_msr() to vmx_find_msr_index() in preparation for an
upcoming patch where we export it and use it in nested.c.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename NR_AUTOLOAD_MSRS to NR_LOADSTORE_MSRS. This needs to be done
due to the addition of the MSR-autostore area that will be added in a
future patch. After that the name AUTOLOAD will no longer make sense.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When L1 don't use TPR-Shadow to run L2, L0 configures vmcs02 without
TPR-Shadow and install intercepts on CR8 access (load and store).
If L1 do not intercept L2 CR8 access, L0 intercepts on those accesses
will emulate load/store on L1's LAPIC TPR. If in this case L2 lowers
TPR such that there is now an injectable interrupt to L1,
apic_update_ppr() will request a KVM_REQ_EVENT which will trigger a call
to update_cr8_intercept() to update TPR-Threshold to highest pending IRR
priority.
However, this update to TPR-Threshold is done while active vmcs is
vmcs02 instead of vmcs01. Thus, when later at some point L0 will
emulate an exit from L2 to L1, L1 will still run with high
TPR-Threshold. This will result in every VMEntry to L1 to immediately
exit on TPR_BELOW_THRESHOLD and continue to do so infinitely until
some condition will cause KVM_REQ_EVENT to be set.
(Note that TPR_BELOW_THRESHOLD exit handler do not set KVM_REQ_EVENT
until apic_update_ppr() will notice a new injectable interrupt for PPR)
To fix this issue, change update_cr8_intercept() such that if L2 lowers
L1's TPR in a way that requires to lower L1's TPR-Threshold, save update
to TPR-Threshold and apply it to vmcs01 when L0 emulates an exit from
L2 to L1.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's enough to check the exit value and issue a direct call to avoid
the retpoline for all the common vmexit reasons.
Of course CONFIG_RETPOLINE already forbids gcc to use indirect jumps
while compiling all switch() statements, however switch() would still
allow the compiler to bisect the case value. It's more efficient to
prioritize the most frequent vmexits instead.
The halt may be slow paths from the point of the guest, but not
necessarily so from the point of the host if the host runs at full CPU
capacity and no host CPU is ever left idle.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Eliminate wasteful call/ret non RETPOLINE case and unnecessary fentry
dynamic tracing hooking points.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Streamline the PID.PIR check and change its call sites to use
the newly added helper.
Suggested-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When vCPU enters block phase, pi_pre_block() inserts vCPU to a per pCPU
linked list of all vCPUs that are blocked on this pCPU. Afterwards, it
changes PID.NV to POSTED_INTR_WAKEUP_VECTOR which its handler
(wakeup_handler()) is responsible to kick (unblock) any vCPU on that
linked list that now has pending posted interrupts.
While vCPU is blocked (in kvm_vcpu_block()), it may be preempted which
will cause vmx_vcpu_pi_put() to set PID.SN. If later the vCPU will be
scheduled to run on a different pCPU, vmx_vcpu_pi_load() will clear
PID.SN but will also *overwrite PID.NDST to this different pCPU*.
Instead of keeping it with original pCPU which vCPU had entered block
phase on.
This results in an issue because when a posted interrupt is delivered, as
the wakeup_handler() will be executed and fail to find blocked vCPU on
its per pCPU linked list of all vCPUs that are blocked on this pCPU.
Which is due to the vCPU being placed on a *different* per pCPU
linked list i.e. the original pCPU in which it entered block phase.
The regression is introduced by commit c112b5f502 ("KVM: x86:
Recompute PID.ON when clearing PID.SN"). Therefore, partially revert
it and reintroduce the condition in vmx_vcpu_pi_load() responsible for
avoiding changing PID.NDST when loading a blocked vCPU.
Fixes: c112b5f502 ("KVM: x86: Recompute PID.ON when clearing PID.SN")
Tested-by: Nathan Ni <nathan.ni@oracle.com>
Co-developed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 17e433b543 ("KVM: Fix leak vCPU's VMCS value into other pCPU")
introduced vmx_dy_apicv_has_pending_interrupt() in order to determine
if a vCPU have a pending posted interrupt. This routine is used by
kvm_vcpu_on_spin() when searching for a a new runnable vCPU to schedule
on pCPU instead of a vCPU doing busy loop.
vmx_dy_apicv_has_pending_interrupt() determines if a
vCPU has a pending posted interrupt solely based on PID.ON. However,
when a vCPU is preempted, vmx_vcpu_pi_put() sets PID.SN which cause
raised posted interrupts to only set bit in PID.PIR without setting
PID.ON (and without sending notification vector), as depicted in VT-d
manual section 5.2.3 "Interrupt-Posting Hardware Operation".
Therefore, checking PID.ON is insufficient to determine if a vCPU has
pending posted interrupts and instead we should also check if there is
some bit set on PID.PIR if PID.SN=1.
Fixes: 17e433b543 ("KVM: Fix leak vCPU's VMCS value into other pCPU")
Reviewed-by: Jagannathan Raman <jag.raman@oracle.com>
Co-developed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Outstanding Notification (ON) bit is part of the Posted Interrupt
Descriptor (PID) as opposed to the Posted Interrupts Register (PIR).
The latter is a bitmap for pending vectors.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX already does so if the host has SMEP, in order to support the combination of
CR0.WP=1 and CR4.SMEP=1. However, it is perfectly safe to always do so, and in
fact VMX already ends up running with EFER.NXE=1 on old processors that lack the
"load EFER" controls, because it may help avoiding a slow MSR write. Removing
all the conditionals simplifies the code.
SVM does not have similar code, but it should since recent AMD processors do
support SMEP. So this patch also makes the code for the two vendors more similar
while fixing NPT=0, CR0.WP=1 and CR4.SMEP=1 on AMD processors.
Cc: stable@vger.kernel.org
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hoist support for RDMSR/WRMSR of IA32_XSS from vmx into common code so
that it can be used for svm as well.
Right now, kvm only allows the guest IA32_XSS to be zero,
so the guest's usage of XSAVES will be exactly the same as XSAVEC.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: Ie4b0f777d71e428fbee6e82071ac2d7618e9bb40
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hoist the vendor-specific code related to loading the hardware IA32_XSS
MSR with guest/host values on VM-entry/VM-exit to common x86 code.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: Ic6e3430833955b98eb9b79ae6715cf2a3fdd6d82
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the guest can execute the XSAVES/XRSTORS instructions, use wrmsr to
set the hardware IA32_XSS MSR to guest/host values on VM-entry/VM-exit,
rather than the MSR-load areas. By using the same approach as AMD, we
will be able to use a common implementation for both (in the next
patch).
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: I9447d104b2615c04e39e4af0c911e1e7309bf464
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Volume 4 of the SDM says that IA32_XSS is supported
if CPUID(EAX=0DH,ECX=1):EAX.XSS[bit 3] is set, so only the
X86_FEATURE_XSAVES check is necessary (X86_FEATURE_XSAVES is the Linux
name for CPUID(EAX=0DH,ECX=1):EAX.XSS[bit 3]).
Fixes: 4d763b168e ("KVM: VMX: check CPUID before allowing read/write of IA32_XSS")
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: I9059b9f2e3595e4b09a4cdcf14b933b22ebad419
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cache whether XSAVES is enabled in the guest by adding xsaves_enabled to
vcpu->arch.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: If4638e0901c28a4494dad2e103e2c075e8ab5d68
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename {vmx,nested_vmx}_vcpu_setup() to match what they really do.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the initialization of vmx->guest_msrs[] from vmx_vcpu_setup() to
vmx_create_vcpu(), and put it right after its allocation.
This also is the preperation for next patch.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
... It can be removed here because the same code is called later in
vmx_vcpu_reset() as the flow:
kvm_arch_vcpu_setup()
-> kvm_vcpu_reset()
-> vmx_vcpu_reset()
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the code that writes vmx->vpid to vmcs from vmx_vcpu_reset() to
vmx_vcpu_setup(), because vmx->vpid is allocated when creating vcpu and
never changed. So we don't need to update the vmcs.vpid when resetting
vcpu.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Generally, APICv for all vcpus in the VM are enable/disable in the same
manner. So, get_enable_apicv() should represent APICv status of the VM
instead of each VCPU.
Modify kvm_x86_ops.get_enable_apicv() to take struct kvm as parameter
instead of struct kvm_vcpu.
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Handle caching CR3 (from VMX's VMCS) into struct kvm_vcpu via the common
cache_reg() callback and drop the dedicated decache_cr3(). The name
decache_cr3() is somewhat confusing as the caching behavior of CR3
follows that of GPRs, RFLAGS and PDPTRs, (handled via cache_reg()), and
has nothing in common with the caching behavior of CR0/CR4 (whose
decache_cr{0,4}_guest_bits() likely provided the 'decache' verbiage).
This would effectivel adds a BUG() if KVM attempts to cache CR3 on SVM.
Change it to a WARN_ON_ONCE() -- if the cache never requires filling,
the value is already in the right place -- and opportunistically add one
in VMX to provide an equivalent check.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add helpers to prettify code that tests and/or marks whether or not a
register is available and/or dirty.
Suggested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rework vmx_set_rflags() to avoid the extra code need to handle emulation
of real mode and invalid state when unrestricted guest is disabled. The
primary reason for doing so is to avoid the call to vmx_get_rflags(),
which will incur a VMREAD when RFLAGS is not already available. When
running nested VMs, the majority of calls to vmx_set_rflags() will occur
without an associated vmx_get_rflags(), i.e. when stuffing GUEST_RFLAGS
during transitions between vmcs01 and vmcs02.
Note, vmx_get_rflags() guarantees RFLAGS is marked available.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Replace "else" with early "return" in the unrestricted guest branch. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Capture struct vcpu_vmx in a local variable to improve the readability
of vmx_{g,s}et_rflags().
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Skip the VMWRITE to update GUEST_CR3 if CR3 is not available, i.e. has
not been read from the VMCS since the last VM-Enter. If vcpu->arch.cr3
is stale, kvm_read_cr3(vcpu) will refresh vcpu->arch.cr3 from the VMCS,
meaning KVM will do a VMREAD and then VMWRITE the value it just pulled
from the VMCS.
Note, this is a purely theoretical change, no instances of skipping
the VMREAD+VMWRITE have been observed with this change.
Tested-by: Reto Buerki <reet@codelabs.ch>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Write the desired L2 CR3 into vmcs02.GUEST_CR3 during nested VM-Enter
instead of deferring the VMWRITE until vmx_set_cr3(). If the VMWRITE
is deferred, then KVM can consume a stale vmcs02.GUEST_CR3 when it
refreshes vmcs12->guest_cr3 during nested_vmx_vmexit() if the emulated
VM-Exit occurs without actually entering L2, e.g. if the nested run
is squashed because nested VM-Enter (from L1) is putting L2 into HLT.
Note, the above scenario can occur regardless of whether L1 is
intercepting HLT, e.g. L1 can intercept HLT and then re-enter L2 with
vmcs.GUEST_ACTIVITY_STATE=HALTED. But practically speaking, a VMM will
likely put a guest into HALTED if and only if it's not intercepting HLT.
In an ideal world where EPT *requires* unrestricted guest (and vice
versa), VMX could handle CR3 similar to how it handles RSP and RIP,
e.g. mark CR3 dirty and conditionally load it at vmx_vcpu_run(). But
the unrestricted guest silliness complicates the dirty tracking logic
to the point that explicitly handling vmcs02.GUEST_CR3 during nested
VM-Enter is a simpler overall implementation.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Reto Buerki <reet@codelabs.ch>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit bf653b78f9 ("KVM: vmx: Introduce handle_unexpected_vmexit
and handle WAITPKG vmexit") introduced specialized handling of
specific exit-reasons that should not be raised by CPU because
KVM configures VMCS such that they should never be raised.
However, since commit 7396d337cf ("KVM: x86: Return to userspace
with internal error on unexpected exit reason"), VMX & SVM
exit handlers were modified to generically handle all unexpected
exit-reasons by returning to userspace with internal error.
Therefore, there is no need for specialized handling of specific
unexpected exit-reasons (This specialized handling also introduced
inconsistency for these exit-reasons to silently skip guest instruction
instead of return to userspace on internal-error).
Fixes: bf653b78f9 ("KVM: vmx: Introduce handle_unexpected_vmexit and handle WAITPKG vmexit")
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The l1tf_vmx_mitigation is only set to VMENTER_L1D_FLUSH_NOT_REQUIRED
when the ARCH_CAPABILITIES MSR indicates that L1D flush is not required.
However, if the CPU is not affected by L1TF, l1tf_vmx_mitigation will
still be set to VMENTER_L1D_FLUSH_AUTO. This is certainly not the best
option for a !X86_BUG_L1TF CPU.
So force l1tf_vmx_mitigation to VMENTER_L1D_FLUSH_NOT_REQUIRED to make it
more explicit in case users are checking the vmentry_l1d_flush parameter.
Signed-off-by: Waiman Long <longman@redhat.com>
[Patch rewritten accoring to Borislav Petkov's suggestion. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The following was reported on i386:
arch/x86/kvm/vmx/vmx.c: In function 'hv_enable_direct_tlbflush':
arch/x86/kvm/vmx/vmx.c:503:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
pr_debugs() in this function are more or less useless, let's just
remove them. evmcs->hv_vm_id can use 'unsigned long' instead of 'u64'.
Also, simplify the code a little bit.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that VMREAD flows require a taken branch, courtesy of commit
3901336ed9 ("x86/kvm: Don't call kvm_spurious_fault() from .fixup")
bite the bullet and add full error handling to VMREAD, i.e. replace the
JMP added by __ex()/____kvm_handle_fault_on_reboot() with a hinted Jcc.
To minimize the code footprint, add a helper function, vmread_error(),
to handle both faults and failures so that the inline flow has a single
CALL.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rework the VMX instruction helpers using asm-goto to branch directly
to error/fault "handlers" in lieu of using __ex(), i.e. the generic
____kvm_handle_fault_on_reboot(). Branching directly to fault handling
code during fixup avoids the extra JMP that is inserted after every VMX
instruction when using the generic "fault on reboot" (see commit
3901336ed9, "x86/kvm: Don't call kvm_spurious_fault() from .fixup").
Opportunistically clean up the helpers so that they all have consistent
error handling and messages.
Leave the usage of ____kvm_handle_fault_on_reboot() (via __ex()) in
kvm_cpu_vmxoff() and nested_vmx_check_vmentry_hw() as is. The VMXOFF
case is not a fast path, i.e. the cleanliness of __ex() is worth the
JMP, and the extra JMP in nested_vmx_check_vmentry_hw() is unavoidable.
Note, VMREAD cannot get the asm-goto treatment as output operands aren't
compatible with GCC's asm-goto due to internal compiler restrictions.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As the latest Intel 64 and IA-32 Architectures Software Developer's
Manual, UMWAIT and TPAUSE instructions cause a VM exit if the
RDTSC exiting and enable user wait and pause VM-execution
controls are both 1.
Because KVM never enable RDTSC exiting, the vm-exit for UMWAIT and TPAUSE
should never happen. Considering EXIT_REASON_XSAVES and
EXIT_REASON_XRSTORS is also unexpected VM-exit for KVM. Introduce a common
exit helper handle_unexpected_vmexit() to handle these unexpected VM-exit.
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Co-developed-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
UMWAIT and TPAUSE instructions use 32bit IA32_UMWAIT_CONTROL at MSR index
E1H to determines the maximum time in TSC-quanta that the processor can
reside in either C0.1 or C0.2.
This patch emulates MSR IA32_UMWAIT_CONTROL in guest and differentiate
IA32_UMWAIT_CONTROL between host and guest. The variable
mwait_control_cached in arch/x86/kernel/cpu/umwait.c caches the MSR value,
so this patch uses it to avoid frequently rdmsr of IA32_UMWAIT_CONTROL.
Co-developed-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
UMONITOR, UMWAIT and TPAUSE are a set of user wait instructions.
This patch adds support for user wait instructions in KVM. Availability
of the user wait instructions is indicated by the presence of the CPUID
feature flag WAITPKG CPUID.0x07.0x0:ECX[5]. User wait instructions may
be executed at any privilege level, and use 32bit IA32_UMWAIT_CONTROL MSR
to set the maximum time.
The behavior of user wait instructions in VMX non-root operation is
determined first by the setting of the "enable user wait and pause"
secondary processor-based VM-execution control bit 26.
If the VM-execution control is 0, UMONITOR/UMWAIT/TPAUSE cause
an invalid-opcode exception (#UD).
If the VM-execution control is 1, treatment is based on the
setting of the “RDTSC exiting†VM-execution control. Because KVM never
enables RDTSC exiting, if the instruction causes a delay, the amount of
time delayed is called here the physical delay. The physical delay is
first computed by determining the virtual delay. If
IA32_UMWAIT_CONTROL[31:2] is zero, the virtual delay is the value in
EDX:EAX minus the value that RDTSC would return; if
IA32_UMWAIT_CONTROL[31:2] is not zero, the virtual delay is the minimum
of that difference and AND(IA32_UMWAIT_CONTROL,FFFFFFFCH).
Because umwait and tpause can put a (psysical) CPU into a power saving
state, by default we dont't expose it to kvm and enable it only when
guest CPUID has it.
Detailed information about user wait instructions can be found in the
latest Intel 64 and IA-32 Architectures Software Developer's Manual.
Co-developed-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX's EPT misconfig flow to handle fast-MMIO path falls back to decoding
the instruction to determine the instruction length when running as a
guest (Hyper-V doesn't fill VMCS.VM_EXIT_INSTRUCTION_LEN because it's
technically not defined for EPT misconfigs). Rather than implement the
slow skip in VMX's generic skip_emulated_instruction(),
handle_ept_misconfig() directly calls kvm_emulate_instruction() with
EMULTYPE_SKIP, which intentionally doesn't do single-step detection, and
so handle_ept_misconfig() misses a single-step #DB.
Rework the EPT misconfig fallback case to route it through
kvm_skip_emulated_instruction() so that single-step #DBs and interrupt
shadow updates are handled automatically. I.e. make VMX's slow skip
logic match SVM's and have the SVM flow not intentionally avoid the
shadow update.
Alternatively, the handle_ept_misconfig() could manually handle single-
step detection, but that results in EMULTYPE_SKIP having split logic for
the interrupt shadow vs. single-step #DBs, and split emulator logic is
largely what led to this mess in the first place.
Modifying SVM to mirror VMX flow isn't really an option as SVM's case
isn't limited to a specific exit reason, i.e. handling the slow skip in
skip_emulated_instruction() is mandatory for all intents and purposes.
Drop VMX's skip_emulated_instruction() wrapper since it can now fail,
and instead WARN if it fails unexpectedly, e.g. if exit_reason somehow
becomes corrupted.
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: d391f12070 ("x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Deferring emulation failure handling (in some cases) to the caller of
x86_emulate_instruction() has proven fragile, e.g. multiple instances of
KVM not setting run->exit_reason on EMULATE_FAIL, largely due to it
being difficult to discern what emulation types can return what result,
and which combination of types and results are handled where.
Now that x86_emulate_instruction() always handles emulation failure,
i.e. EMULATION_FAIL is only referenced in callers, remove the
emulation_result enums entirely. Per KVM's existing exit handling
conventions, return '0' and '1' for "exit to userspace" and "resume
guest" respectively. Doing so cleans up many callers, e.g. they can
return kvm_emulate_instruction() directly instead of having to interpret
its result.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that EMULATE_FAIL is completely unused, remove the last remaning
usage where KVM does something functional in response to EMULATE_FAIL.
Leave the check in place as a WARN_ON_ONCE to provide a better paper
trail when EMULATE_{DONE,FAIL,USER_EXIT} are completely removed.
Opportunistically remove the gotos in handle_invalid_guest_state().
With the EMULATE_FAIL handling gone there is no need to have a common
handler for emulation failure and the gotos only complicate things,
e.g. the signal_pending() check always returns '1', but this is far
from obvious when glancing through the code.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Request triple fault in kvm_inject_realmode_interrupt() instead of
returning EMULATE_FAIL and deferring to the caller. All existing
callers request triple fault and it's highly unlikely Real Mode is
going to acquire new features. While this consolidates a small amount
of code, the real goal is to remove the last reference to EMULATE_FAIL.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Consolidate the reporting of emulation failure into kvm_task_switch()
so that it can return EMULATE_USER_EXIT. This helps pave the way for
removing EMULATE_FAIL altogether.
This also fixes a theoretical bug where task switch interception could
suppress an EMULATE_USER_EXIT return.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Immediately inject a #GP when VMware emulation fails and return
EMULATE_DONE instead of propagating EMULATE_FAIL up the stack. This
helps pave the way for removing EMULATE_FAIL altogether.
Rename EMULTYPE_VMWARE to EMULTYPE_VMWARE_GP to document that the x86
emulator is called to handle VMware #GP interception, e.g. why a #GP
is injected on emulation failure for EMULTYPE_VMWARE_GP.
Drop EMULTYPE_NO_UD_ON_FAIL as a standalone type. The "no #UD on fail"
is used only in the VMWare case and is obsoleted by having the emulator
itself reinject #GP.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The VMware backdoor hooks #GP faults on IN{S}, OUT{S}, and RDPMC, none
of which generate a non-zero error code for their #GP. Re-injecting #GP
instead of attempting emulation on a non-zero error code will allow a
future patch to move #GP injection (for emulation failure) into
kvm_emulate_instruction() without having to plumb in the error code.
Reviewed-and-tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the stat.mmio_exits update into x86_emulate_instruction(). This is
both a bug fix, e.g. the current update flows will incorrectly increment
mmio_exits on emulation failure, and a preparatory change to set the
stage for eliminating EMULATE_DONE and company.
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jim Mattson