A ticket was not released after a call of the function
"rxkad_decrypt_ticket" failed. Thus replace the jump target
"temporary_error_free_resp" by "temporary_error_free_ticket".
Fixes: 8c2f826dc3 ("rxrpc: Don't put crypto buffers on the stack")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Markus Elfring <Markus.Elfring@web.de>
Fix a warning due to an uninitialised variable.
le included from ../fs/afs/fs_probe.c:11:
../fs/afs/fs_probe.c: In function 'afs_fileserver_probe_result':
../fs/afs/internal.h:1453:2: warning: 'rtt_us' may be used uninitialized in this function [-Wmaybe-uninitialized]
1453 | printk("[%-6.6s] "FMT"\n", current->comm ,##__VA_ARGS__)
| ^~~~~~
../fs/afs/fs_probe.c:35:15: note: 'rtt_us' was declared here
Signed-off-by: David Howells <dhowells@redhat.com>
In cas_init_one(), "pdev" is requested by "pci_request_regions", but it
was not released after a call of the function “pci_write_config_byte”
failed. Thus replace the jump target “err_write_cacheline” by
"err_out_free_res".
Fixes: 1f26dac320 ("[NET]: Add Sun Cassini driver.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur says:
====================
bridge: mrp: Add br_mrp_unique_ifindex function
This patch series adds small fixes to MRP implementation.
The following are fixed in this patch series:
- now is not allow to add the same port to multiple MRP rings
- remove unused variable
- restore the port state according to the bridge state when the MRP instance
is deleted
v2:
- use rtnl_dereference instead of rcu_dereference in the first patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a MRP instance is deleted, then restore the port according to the
bridge state. If the bridge is up then the ports will be in forwarding
state otherwise will be in disabled state.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the variable mrp_ring_state from switchdev_attr because is not
used anywhere.
The ring state is set using SWITCHDEV_OBJ_ID_RING_STATE_MRP.
Fixes: c284b54590 ("switchdev: mrp: Extend switchdev API to offload MRP")
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allow to have the same net bridge port part of multiple MRP
rings. Therefore add a check if the port is used already in a different
MRP. In that case return failure.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_set_ageing_time has 2 callers:
- felix_set_ageing_time: from drivers/net/dsa/ocelot/felix.c
- ocelot_port_attr_ageing_set: from drivers/net/ethernet/mscc/ocelot.c
The issue described in the fixed commit below actually happened for the
felix_set_ageing_time code path only, since ocelot_port_attr_ageing_set
was already dividing by 1000. So to make both paths symmetrical (and to
fix addresses getting aged way too fast on Ocelot), stop dividing by
1000 at caller side altogether.
Fixes: c0d7eccbc7 ("net: mscc: ocelot: ANA_AUTOAGE_AGE_PERIOD holds a value in seconds, not ms")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to r8168 vendor driver DASHv3 chips like RTL8168fp/RTL8117
need a special addressing for OCP access.
Fix is compile-tested only due to missing test hardware.
Fixes: 1287723aa1 ("r8169: add support for RTL8117")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy says:
====================
DP83869 Enhancements
These are improvements to the DP83869 Ethernet PHY driver. OP-mode and port
mirroring may be strapped on the device but the software only retrives these
settings from the device tree. Reading the straps and initializing the
associated stored variables so when setting the PHY up and down the PHY's
configuration values will be retained.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the op-mode for the device is not set in the device tree then set
the strapped op-mode and store it for later configuration.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree may not have the property set for port mirroring
because the hardware may have it strapped. If the property is not in the
DT then check the straps and set the port mirroring bit appropriately.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
test_lirc_mode2.sh assumes presence of /sys/class/rc/rc0/lirc*/uevent
which will not be present unless CONFIG_LIRC=y
Fixes: 6bdd533cee ("bpf: add selftest for lirc_mode2 type program")
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/1590147389-26482-3-git-send-email-alan.maguire@oracle.com
test_seg6_loop.o uses the helper bpf_lwt_seg6_adjust_srh();
it will not be present if CONFIG_IPV6_SEG6_BPF is not specified.
Fixes: b061017f8b ("selftests/bpf: add realistic loop tests")
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/1590147389-26482-2-git-send-email-alan.maguire@oracle.com
Getting a clean BPF selftests run involves ensuring latest trunk LLVM/clang
are used, pahole is recent (>=1.16) and config matches the specified
config file as closely as possible. Add to bpf_devel_QA.rst and point
tools/testing/selftests/bpf/README.rst to it.
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/1590146674-25485-1-git-send-email-alan.maguire@oracle.com
Ido Schimmel says:
====================
mlxsw: Various fixes
Patch #1 from Jiri fixes a use-after-free discovered while fuzzing mlxsw
/ devlink with syzkaller.
Patch #2 from Amit works around a limitation in new versions of arping,
which is used in several selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from iputils s20190709 (used in Fedora 31), arping does not
support timeout being specified as a decimal:
$ arping -c 1 -I swp1 -b 192.0.2.66 -q -w 0.1
arping: invalid argument: '0.1'
Previously, such timeouts were rounded to an integer.
Fix this by specifying the timeout as an integer.
Fixes: a5ee171d08 ("selftests: mlxsw: qos_mc_aware: Add a test for UC awareness")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of reload fail, the mlxsw_sp->ports contains a pointer to a
freed memory (either by reload_down() or reload_up() error path).
Fix this by initializing the pointer to NULL and checking it before
dereferencing in split/unsplit/type_set callpaths.
Fixes: 24cc68ad6c ("mlxsw: core: Add support for reload")
Reported-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
netdevsim: Two small fixes
Fix two bugs observed while analyzing regression failures.
Patch #1 fixes a bug where sometimes the drop counter of a packet trap
policer would not increase.
Patch #2 adds a missing initialization of a variable in a related
selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable is used by log_test() to check if the test case completely
successfully or not. In case it is not initialized at the start of a
test case, it is possible for the test case to fail despite not
encountering any errors.
Example:
```
...
TEST: Trap group statistics [ OK ]
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
TEST: Trap policer binding [FAIL]
Policer drop counter was not incremented
```
Failure of trap_policer_test() caused trap_policer_bind_test() to fail
as well.
Fix by adding missing initialization of the variable.
Fixes: 5fbff58e27 ("selftests: netdevsim: Add test cases for devlink-trap policers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the policer drop counter is retrieved when the jiffies value is
a multiple of 64, the counter will not be incremented.
This randomly breaks a selftest [1] the reads the counter twice and
checks that it was incremented:
```
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
```
Fix by always incrementing the counter by 1.
[1] tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh
Fixes: ad188458d0 ("netdevsim: Add devlink-trap policer support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon adapter hotplug, cxgb4 registers ULD devices for all the ULDs that
are already loaded, ensuring that ULD's can enumerate the hotplugged
adapter without reloading the ULD.
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=jJvy
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20200520' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix retransmission timeout and ACK discard
Here are a couple of fixes and an extra tracepoint for AF_RXRPC:
(1) Calculate the RTO pretty much as TCP does, rather than making
something up, including an initial 4s timeout (which causes return
probes from the fileserver to fail if a packet goes missing), and add
backoff.
(2) Fix the discarding of out-of-order received ACKs. We mustn't let the
hard-ACK point regress, nor do we want to do unnecessary
retransmission because the soft-ACK list regresses. This is not
trivial, however, due to some loose wording in various old protocol
specs, the ACK field that should be used for this sometimes has the
wrong information in it.
(3) Add a tracepoint to log a discarded ACK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make FLOW_ACTION_HW_STATS_DONT_CARE be all bits, rather than none, so that
drivers and __flow_action_hw_stats_check can use simple bitwise checks.
Pre-fill all actions with DONT_CARE in flow_rule_alloc(), rather than
relying on implicit semantics of zero from kzalloc, so that callers which
don't configure action stats themselves (i.e. netfilter) get the correct
behaviour by default.
Only the kernel's internal API semantics change; the TC uAPI is unaffected.
v4: move DONT_CARE setting to flow_rule_alloc() for robustness and simplicity.
v3: set DONT_CARE in nft and ct offload.
v2: rebased on net-next, removed RFC tags.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
[1] https://lists.openwall.net/netdev/2020/01/08/201
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Fedorenko says:
====================
ip6_tunnel: add MPLS support
The support for MPLS-in-IPv4 was added earlier. This patchset adds
support for MPLS-in-IPv6.
Changes in v2:
- Eliminate ifdefs IS_ENABLE(CONFIG_MPLS)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 tunnel devices in AF_MPLS.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is just preparation for MPLS support in ip6_tunnel
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge ip{4,6}ip6_tnl_xmit functions into one universal
ipxip6_tnl_xmit in preparation for adding MPLS support.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bdf6fa52f0 ("sctp: handle association restarts when the
socket is closed.") starts shutdown when an association is restarted,
if in SHUTDOWN-PENDING state and the socket is closed. However, the
rationale stated in that commit applies also when in SHUTDOWN-SENT
state - we don't want to move an association to ESTABLISHED state when
the socket has been closed, because that results in an association
that is unreachable from user space.
The problem scenario:
1. Client crashes and/or restarts.
2. Server (using one-to-one socket) calls close(). SHUTDOWN is lost.
3. Client reconnects using the same addresses and ports.
4. Server's association is restarted. The association and the socket
move to ESTABLISHED state, even though the server process has
closed its descriptor.
Also, after step 4 when the server process exits, some resources are
leaked in an attempt to release the underlying inet sock structure in
ESTABLISHED state:
IPv4: Attempt to release TCP socket in state 1 00000000377288c7
Fix by acting the same way as in SHUTDOWN-PENDING state. That is, if
an association is restarted in SHUTDOWN-SENT state and the socket is
closed, then start shutdown and don't move the association or the
socket to ESTABLISHED state.
Fixes: bdf6fa52f0 ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rxhash is enabled on any ethernet port except the first in each CP
block, traffic flow is prevented. The analysis is below:
I've been investigating this afternoon, and what I've found, comparing
a kernel without 895586d5dc and with 895586d5dc applied is:
- The table programmed into the hardware via mvpp22_rss_fill_table()
appears to be identical with or without the commit.
- When rxhash is enabled on eth2, mvpp2_rss_port_c2_enable() reports
that c2.attr[0] and c2.attr[2] are written back containing:
- with 895586d5dc, failing: 00200000 40000000
- without 895586d5dc, working: 04000000 40000000
- When disabling rxhash, c2.attr[0] and c2.attr[2] are written back as:
04000000 00000000
The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the
first value is the queue number, which comprises two fields. The high
5 bits are 24:29 and the low three are 21:23 inclusive. This comes
from:
c2.attr[0] = MVPP22_CLS_C2_ATTR0_QHIGH(qh) |
MVPP22_CLS_C2_ATTR0_QLOW(ql);
So, the working case gives eth2 a queue id of 4.0, or 32 as per
port->first_rxq, and the non-working case a queue id of 0.1, or 1.
The allocation of queue IDs seems to be in mvpp2_port_probe():
if (priv->hw_version == MVPP21)
port->first_rxq = port->id * port->nrxqs;
else
port->first_rxq = port->id * priv->max_port_rxqs;
Where:
if (priv->hw_version == MVPP21)
priv->max_port_rxqs = 8;
else
priv->max_port_rxqs = 32;
Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1
(eth2) be 32. It seems the idea is that the first 32 queues belong to
port 0, the second 32 queues belong to port 1, etc.
mvpp2_rss_port_c2_enable() gets the queue number from it's parameter,
'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns
port->rss_ctx[0].
mvpp22_rss_context_create() is responsible for allocating that, which
it does by looking for an unallocated priv->rss_tables[] pointer. This
table is shared amongst all ports on the CP silicon.
When we write the tables in mvpp22_rss_fill_table(), the RSS table
entry is defined by:
u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) |
MVPP22_RSS_INDEX_TABLE_ENTRY(i);
where rss_ctx is the context ID (queue number) and i is the index in
the table.
If we look at what is written:
- The first table to be written has "sel" values of 00000000..0000001f,
containing values 0..3. This appears to be for eth1. This is table 0,
RX queue number 0.
- The second table has "sel" values of 00000100..0000011f, and appears
to be for eth2. These contain values 0x20..0x23. This is table 1,
RX queue number 0.
- The third table has "sel" values of 00000200..0000021f, and appears
to be for eth3. These contain values 0x40..0x43. This is table 2,
RX queue number 0.
How do queue numbers translate to the RSS table? There is another
table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field
of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE
register. Before 895586d5dc, it was:
mvpp2_write(priv, MVPP22_RSS_INDEX,
MVPP22_RSS_INDEX_QUEUE(port->first_rxq));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE,
MVPP22_RSS_TABLE_POINTER(port->id));
and after:
mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(ctx));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(ctx));
Before the commit, for eth2, that would've contained '32' for the
index and '1' for the table pointer - mapping queue 32 to table 1.
Remember that this is queue-high.queue-low of 4.0.
After the commit, we appear to map queue 1 to table 1. That again
looks fine on the face of it.
Section 9.3.1 of the A8040 manual seems indicate the reason that the
queue number is separated. queue-low seems to always come from the
classifier, whereas queue-high can be from the ingress physical port
number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG.
We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high
comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to
be where our bug comes from.
mvpp2_cls_oversize_rxq_set() sets this up as:
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_P2HQ_REG(port->id),
(port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS));
val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG);
val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id);
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val);
Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high
for eth2 is _always_ 4, so only queues 32 through 39 inclusive are
available to eth2. Yet, we're trying to tell the classifier to set
queue-high, which will be ignored, to zero. Hence, the queue-high
field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be
ignored.
This means we end up directing traffic from eth2 not to queue 1, but
to queue 33, and then we tell it to look up queue 33 in the RSS table.
However, RSS table has not been programmed for queue 33, and so it ends
up (presumably) dropping the packets.
It seems that mvpp22_rss_context_create() doesn't take account of the
fact that the upper 5 bits of the queue ID can't actually be changed
due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that
mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either
way, these two functions mutually disagree with what queue number
should be used.
Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU
validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used
for over-sized packets attempting to egress through this port. With
the classifier having had RSS enabled and directing eth2 traffic to
queue 1, we may still have packets appearing on queue 32 for this port.
However, the only way we may end up with over-sized packets attempting
to egress through eth2 - is if the A8040 forwards frames between its
ports. From what I can see, we don't support that feature, and the
kernel restricts the egress packet size to the MTU. In any case, if we
were to attempt to transmit an oversized packet, we have no support in
the kernel to deal with that appearing in the port's receive queue.
So, this patch attempts to solve the issue by clearing the
MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH()
from the classifier to define the queue-high field of the queue number.
My testing seems to confirm my findings above - clearing this bit
means that if I enable rxhash on eth2, the interface can then pass
traffic, as we are now directing traffic to RX queue 1 rather than
queue 33. Traffic still seems to work with rxhash off as well.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Fixes: 895586d5dc ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-05-22
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 3 day(s) which contain
a total of 5 files changed, 69 insertions(+), 11 deletions(-).
The main changes are:
1) Fix to reject mmap()'ing read-only array maps as writable since BPF verifier
relies on such map content to be frozen, from Andrii Nakryiko.
2) Fix breaking audit from secid_to_secctx() LSM hook by avoiding to use
call_int_hook() since this hook is not stackable, from KP Singh.
3) Fix BPF flow dissector program ref leak on netns cleanup, from Jakub Sitnicki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is some ambiguity in the RFC as to whether the ADD_ADDR HMAC is
the rightmost 64 bits of the entire hash or of the leftmost 160 bits
of the hash. The intention, as clarified with the author of the RFC,
is the entire hash.
This change returns the entire hash from
mptcp_crypto_hmac_sha (instead of only the first 160 bits), and moves
any truncation/selection operation on the hash to the caller.
Fixes: 12555a2d97 ("mptcp: use rightmost 64 bits in ADD_ADDR HMAC")
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Todd Malsbary <todd.malsbary@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski says:
====================
mediatek: add support for MediaTek Ethernet MAC
This series adds support for the STAR Ethernet Controller present on MediaTeK
SoCs from the MT8* family.
First we convert the existing DT bindings for the PERICFG controller to YAML
and add a new compatible string for mt8516 variant of it. Then we add the DT
bindings for the MAC.
Next we do some cleanup of the mediatek ethernet drivers directory.
The largest patch in the series adds the actual new driver.
The rest of the patches add DT fixups for the boards already supported
upstream.
v1 -> v2:
- add a generic helper for retrieving the net_device associated with given
private data
- fix several typos in commit messages
- remove MTK_MAC_VERSION and don't set the driver version
- use NET_IP_ALIGN instead of a magic number (2) but redefine it as it defaults
to 0 on arm64
- don't manually turn the carrier off in mtk_mac_enable()
- process TX cleanup in napi poll callback
- configure pause in the adjust_link callback
- use regmap_read_poll_timeout() instead of handcoding the polling
- use devres_find() to verify that struct net_device is managed by devres in
devm_register_netdev()
- add a patch moving all networking devres helpers into net/devres.c
- tweak the dma barriers: remove where unnecessary and add comments to the
remaining barriers
- don't reset internal counters when enabling the NIC
- set the net_device's mtu size instead of checking the framesize in
ndo_start_xmit() callback
- fix a race condition in waking up the netif queue
- don't emit log messages on OOM errors
- use dma_set_mask_and_coherent()
- use eth_hw_addr_random()
- rework the receive callback so that we reuse the previous skb if unmapping
fails, like we already do if skb allocation fails
- rework hash table operations: add proper timeout handling and clear bits when
appropriate
v2 -> v3:
- drop the patch adding priv_to_netdev() and store the netdev pointer in the
driver private data
- add an additional dma_wmb() after reseting the descriptor in
mtk_mac_ring_pop_tail()
- check the return value of dma_set_mask_and_coherent()
- improve the DT bindings for mtk-eth-mac: make the reg property in the example
use single-cell address and size, extend the description of the PERICFG
phandle and document the mdio sub-node
- add a patch converting the old .txt bindings for PERICFG to yaml
- limit reading the DMA memory by storing the mapped addresses in the driver
private structure
- add a patch documenting the existing networking devres helpers
v3 -> v4:
- drop the devres patches: they will be sent separately
- call netdev_sent_queue() & netdev_completed_queue() where appropriate
- don't redefine NET_IP_ALIGN: define a private constant in the driver
- fix a couple typos
- only disabe/enable the MAC in suspend/resume if netif is running
- drop the count field from the ring structure and instead calculate the number
of used descriptors from the tail and head indicies
- rework the locking used to protect the ring structures from concurrent
access: use cheaper spin_lock_bh() and completely disable the internal
spinlock used by regmap
- rework the interrupt handling to make it more fine-grained: onle re-enable
TX and RX interrupts while they're needed, process the stats updates in a
workqueue, not in napi context
- shrink the code responsible for unmapping and freeing skb memory
- rework the barriers as advised by Arnd
v4 -> v5:
- rename the driver to make it less confusing with the existing mtk_eth_soc
ethernet driver
- unregister the mdiobus at device's detachment
- open-code spin lock calls to avoid calling the _bh variants where unnecessary
- limit read-modify-write operations where possible when accessing descriptor
memory
- use READ_ONCE/WRITE_ONCE when modifying the status and data_ptr descriptor
fields
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add remaining properties to the ethernet node and enable it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup the pin control for the Ethernet MAC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ethernet0 alias for ethernet so that u-boot can find this node
and fill in the MAC address.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Ethernet MAC node to mt8516.dtsi. This defines parameters common
to all the boards based on this SoC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the PERICFG register range as a syscon. This will
soon be used by the MediaTek Ethernet MAC driver for NIC configuration.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the driver for the MediaTek STAR Ethernet MAC currently used
on the MT8* SoC family. For now we only support full-duplex.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Makefile formatting in the kernel tree usually doesn't use tabs,
so remove them before we add a second driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll soon by adding a second MediaTek Ethernet driver so modify the
Kconfig prompt.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds yaml DT bindings for the MediaTek STAR Ethernet MAC present
on the mt8* family of SoCs.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PERICFG controller is present on the MT8516 SoC. Add an appropriate
compatible variant.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
