This patch changes the way we handle the maximum frame size for the Rx
path. Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount. With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size. This makes the behavior more
consistent with the other drivers such as igb which had similar logic. In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.
Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.
Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
I also found and fixed a store forwarding stall from where we were
assigning "*new_buff = *old_buff". By breaking it up into individual
copies we can avoid this and as a result the performance is slightly
improved.
Change-ID: I1d3880dece4133eca3c32423b04a5467321ccc52
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING. By enabling both of these for the Rx path we
are able to see performance improvements on architectures that implement
either one due to the fact that page mapping and unmapping only has to
sync what is actually being used instead of the entire buffer. In addition
by enabling the weak ordering attribute enables a performance improvement
for architectures that can associate a memory ordering with a DMA buffer
such as Sparc.
Change-ID: If176824e8231c5b24b8a5d55b339a6026738fc75
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reduces the size of struct i40e_rx_buffer by one pointer,
and makes the i40e driver a little more consistent with the igb driver
in terms of packets that span buffers.
We do this by moving the skb field from struct i40e_rx_buffer to
struct i40e_ring. We pass the skb we already have (or NULL if we
don't) to i40e_fetch_rx_buffer(), which skips the skb allocation if we
already have one for this packet.
Change-ID: I4ad48a531844494ba0c5d8e1a62209a057f661b0
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the macro INTRL_USEC_TO_REG into a static inline
function and fixes a couple subtle bugs caused by the macro.
This patch fixes a bug which was caused by passing a bad register value
to the firmware. If enabling interrupt rate limiting, a non-zero value
for the rate limit must be used. Otherwise the firmware sets the
interrupt rate limit to the maximum value. Due to the limited
resolution of the register, attempting to set a value of 1, 2, or 3
would be rounded down to 0 and limiting was left enabled, causing
unexpected behavior.
This patch also fixes a possible bug in which using the macro itself can
introduce unintended side-affects because the macro argument is used
more than once in the macro definition (e.g. a variable post-increment
argument would perform a double increment on the variable).
Without this patch, attempting to set interrupt rate limits of 1, 2, or
3 results in unexpected behavior and future use of this macro could
cause subtle bugs.
Change-Id: I83ac842de0ca9c86761923d6e3a4d7b1b95f2b3f
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_txd_use_count function was fast but confusing. In the comments,
it even admits that it's ugly. So replace it with a new function that is
(very) slightly faster and has extensive commenting to help the thicker
among us (including the author, who will forget in a week) understand
how it works.
Change-ID: Ifb533f13786a0bf39cb29f77969a5be2c83d9a87
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reorders the logic at the end of i40e_tx_map to address the
fact that the logic was rather convoluted and much larger than it needed
to be.
In order to try and coalesce the code paths I have updated some of the
comments and repurposed some of the variables in order to reduce
unnecessary overhead.
This patch does the following:
1. Quit tracking skb->xmit_more with a flag, just max out packet_stride
2. Drop tail_bump and do_rs and instead just use desc_count and td_cmd
3. Pull comments from ixgbe that make need for wmb() more explicit.
Change-ID: Ic7da85ec75043c634e87fef958109789bcc6317c
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current Rx timestamp hang logic is not very robust because it does
not notice a register is hung until all four timestamps have been
latched and we wait a full 5 seconds. Replace this logic with a newer Rx
hang detection based on storing the jiffies when we first notice
a receive timestamp event. We store each register's time separately,
along with a flag indicating if it is currently latched. Upon first
transitioning to latch, we will update the latch_events[i] jiffies
value. This indicates the time we first noticed this event. The watchdog
routine will simply check that the either the flag has been cleared, or
we have passed at least one second. In this case, it is able to clear
the Rx timestamp register under the assumption that it was for a dropped
frame. The benefit if this strategy is that we should be able to
detect and clear out stalled RXTIME_H registers before we exhaust the
supply of 4, and avoid complete stall of Rx timestamp events.
Change-ID: Id55458c0cd7a5dd0c951ff2b8ac0b2509364131f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a txring_txq function which allows us to convert a
i40e_ring/i40evf_ring to a netdev_tx_queue structure. This way we
can avoid having to make a multi-line function call for all the spots
that need access to this.
Change-ID: Ic063b71d8b92ea406d2c32e798c8e2b02809d65b
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a 16 byte descriptor for receive, but the
driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole
lot of complexity while getting rid of the code.
Also since the previous patch made us use no-split mode all the
time, drop any support in the driver for any other value in dtype
and assume it is always zero (aka no-split).
Hooray for code removal!
Change-ID: I2257e902e4dad84a07b94db6d2e6f4ce69b27bc0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is part 1 of the Rx refactor series, just including
changes to i40e.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split
Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of the rx-refactor, the dtype variable in the i40e_ring
struct is no longer used, so remove it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a bug introduced based on my interpretation of the
XL710 datasheet. Specifically section 8.4.1 states that "A single transmit
packet may span up to 8 buffers (up to 8 data descriptors per packet
including both the header and payload buffers)." It then later goes on to
say that each segment for a TSO obeys the previous rule, however it then
refers to TSO header and the segment payload buffers.
I believe the actual limit for fragments with TSO and a skbuff that has
payload data in the header portion of the buffer is actually only 7
fragments as the skb->data portion counts as 2 buffers, one for the TSO
header, and one for a segment payload buffer.
Fixes: 2d37490b82 ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As it turns out, calling into other files from hot path hurts
performance a lot. In this case the majority of the time we
call "check FCoE" and the packet is *not* FCoE, but this call
was taking 5% of our total cycles spent on receive.
Change-ID: I080552c26e7060bc7b78504dc2763f6f0b3d8c76
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
From what I can tell the practical limitation on the size of the Tx data
buffer is the fact that the Tx descriptor is limited to 14 bits. As such
we cannot use 16K as is typically used on the other Intel drivers. However
artificially limiting ourselves to 8K can be expensive as this means that
we will consume up to 10 descriptors (1 context, 1 for header, and 9 for
payload, non-8K aligned) in a single send.
I propose that we can reduce this by increasing the maximum data for a 4K
aligned block to 12K. We can reduce the descriptors used for a 32K aligned
block by 1 by increasing the size like this. In addition we still have the
4K - 1 of space that is still unused. We can use this as a bit of extra
padding when dealing with data that is not aligned to 4K.
By aligning the descriptors after the first to 4K we can improve the
efficiency of PCIe accesses as we can avoid using byte enables and can fetch
full TLP transactions after the first fetch of the buffer. This helps to
improve PCIe efficiency. Below is the results of testing before and after
with this patch:
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
Before:
87380 16384 16384 10.00 33682.24 20.27 -1.00 0.592 -1.00
After:
87380 16384 16384 10.00 34204.08 20.54 -1.00 0.590 -1.00
So the net result of this patch is that we have a small gain in throughput
due to a reduction in overhead for putting together the frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is meant to rewrite the logic for how we determine if we can
transmit the frame or if it needs to be linearized.
The previous code for this function was using a mix of division and modulus
division as a part of computing if we need to take the slow path. Instead
I have replaced this by simply working with a sliding window which will
tell us if the frame would be capable of causing a single packet to span
several descriptors.
The logic for the scan is fairly simple. If any given group of 6 fragments
is less than gso_size - 1 then it is possible for us to have one byte
coming out of the first fragment, 6 fragments, and one or more bytes coming
out of the last fragment. This gives us a total of 8 fragments
which exceeds what we can allow so we send such frames to be linearized.
Arguably the use of modulus might be more exact as the approach I propose
may generate some false positives. However the likelihood of us taking much
of a hit for those false positives is fairly low, and I would rather not
add more overhead in the case where we are receiving a frame composed of 4K
pages.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In an upcoming patch I would like to have access to the descriptor count
used for the data portion of the frame. For this reason I am splitting up
the descriptor count function from the function that stops the ring.
Also in order to try and reduce unnecessary duplication of code I am moving
the slow-path portions of the code out of being inline calls so that we can
just jump to them and process them instead of having to build them into
each function that calls them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add exception handling to the Tx checksum path so that we can handle cases
of TSO where the frame is bad, or Tx checksum where we didn't recognize a
protocol
Drop I40E_TX_FLAGS_CSUM as it is unused, move the CHECKSUM_PARTIAL check
into the function itself so that we can decrease indent.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e and i40evf drivers contained code for inserting an outer checksum
on UDP tunnels. The issue however is that the upper levels of the stack
never requested such an offload and it results in possible errors.
In addition the same logic was being applied to the Rx side where it was
attempting to validate the outer checksum, but the logic there was
incorrect in that it was testing for the resultant sum to be equal to the
header checksum instead of being equal to 0.
Since this code is so massively flawed, and doing things that we didn't ask
for it to do I am just dropping it, and will bring it back later to use as
an offload for SKB_GSO_UDP_TUNNEL_CSUM which can make use of such a
feature.
As far as the Rx feature I am dropping it completely since it would need to
be massively expanded and applied to IPv4 and IPv6 checksums for all parts,
not just the one that supports Tx checksum offload for the outer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Get rid of the unused hsplit field in the ring struct and use the
existing macro to detect packet split enablement. This allows debugfs
dumps of the VSI to properly show which Rx routine is in use.
Change-ID: Ic4e9589e6a788ab196ed0850703f704e30c03781
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the packet split Rx code to properly use half-pages for
receives. The previous code was doing way more mapping and unmapping
than it needed to, and wasn't properly using half-pages.
Increment the page use count each time we give a half-page to an skb,
knowing that the stack will probably process and release the page before
we need it again. Only free and reallocate pages if the count shows that
both half-pages are in use. Add counters to track reallocations and page
reuse.
Change-ID: I534b299196036b64be82b4861a0a4036310a8f22
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the "Don't Give Up" patch. Previously the
driver could fail an allocation, and then possibly stall
a queue forever, by never coming back to continue receiving
or allocating buffers.
With this patch, the driver will keep polling trying to allocate
receive buffers until it succeeds. This should keep all receive
queues running even in the face of memory pressure.
Also update copyright year in file header.
Change-ID: I2b103d1ce95b9831288a7222c3343ffa1988b81b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in NAPI with interrupts disabled, the HW needs to be forced to do a
write back on TX if the number of descriptors pending are less than a
cache line.
This stat helps keep track of how many times we get into this situation.
Change-ID: I76c1bcc7ebccd6bffcc5aa33bfe05f2fa1c9a984
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently. This caused a lot
of variation in the interrupt rate for fairly constant workloads.
Change the code to have a counter and adjust only once every N
number of interrupts.
Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dynamic algorithm, while now working, doesn't have good
performance in 40G mode.
One part of this patch addresses the high CPU utilization of some small
streaming workloads that the driver should reduce CPU in.
It also changes the minimum ITR that the dynamic algorithm
will settle on, causing our minimum latency to go from 12us
to about 14us, when using adaptive mode.
It also changes the BULK interrupt rate to allow maximum throughput
on a 40Gb connection with a single thread of transmit, clamping
interrupt rate to 8000 for TX makes single thread traffic go too
slow.
The new ULTRA bulk setting is introduced and is used
when the Rx packet rate on this queue exceeds 40000 packets per
second. This value of 40000 was chosen because the automatic tuning
of minimum ITR=20us means that a single queue can't quite achieve
that many packets per second from a round-robin test.
Change-ID: Icce8faa128688ca5fd2c4229bdd9726877a92ea2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.
Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse found some issues with 32 bit compilation, which probably should
at least work without warning. Not only that, but the code was wrong.
Thanks sparse!!
And thanks to the kbuild robot zero day testing for finding this issue.
$ make ARCH=i386 M=drivers/net/ethernet/intel/i40e C=2 CF="-D__CHECK_ENDIAN__"
CHECK drivers/net/ethernet/intel/i40e/i40e_main.c
include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (32) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (42) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (39) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (40) for type unsigned long
CC: kbuild-all@01.org
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump and when
it does a WB. It also optimizes when we do a wmb.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the driver timeout logic by issuing a writeback
request via a software interrupt to the hardware the first time the
driver detects a hang. The driver was too aggressive in resetting a hung
queue, so back that off by removing logic to down the netdevice after
too many hangs, and move the function to the service task.
Change-ID: Ife100b9d124cd08cbdb81ab659008c1b9abbedea
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_get_head needs to be called in multiple files in a further patch,
prepare by moving the function into a header file.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.
NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.
Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver doesn't use the time_stamp member to determine if there is a
tx_hang any more. There really isn't any point to the variable at all
so just remove it. It was left over from a previous tx_hang design.
Change-ID: I4c814827e1bcb46e45118fe37acdcfa814fb62a0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without this, RSS would have done inner header load balancing. Now we can
get the benefits of ATR for tunneled packets to better align TX and RX
queues with the right core/interrupt.
Change-ID: I07d0e0a192faf28fdd33b2f04c32b2a82ff97ddd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has some limitations the driver needs to adhere to,
that we found in extended testing.
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events occurs, the hardware will generate an internal
error and freeze the Tx queue.
This patch linearizes the skb to avoid these situations.
Change-ID: I37dab7d3966e14895a9663ec4d0aaa8eb0d9e115
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the receive hot path code into two, one for packet split and one
for single buffer. This improves receive performance since we only need
to check if the ring is in packet split mode once per NAPI poll time,
not several times per packet. The single buffer code is further improved
by the removal of a bunch of code and several variables that are not
needed. On a receive-oriented test this can improve single-threaded
throughput.
Also refactor the packet split receive path to use a fixed buffer for
headers, like ixgbe does. This vastly reduces the number of DMA mappings
and unmappings we need to do, allowing for much better performance in
the presence of an IOMMU.
Lastly, correct packet split descriptor types now that we are actually
using them.
Change-ID: I3a194a93af3d2c31e77ff17644ac7376da6f3e4b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver was polling with interrupts disabled the hardware
will occasionally not write back descriptors. This patch causes
the driver to detect this situation and force an interrupt to
fire which will flush the stuck descriptor. Does not conflict
with napi because if we are already polling the napi_schedule is
ignored. Additionally the extra interrupts are rate limited, so
don't cause a burden to the CPU.
Change-ID: Iba4616d2a71288672a5f08e4512e2704b97335e8
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interrupt throttle rate minimum is actually 2us, so
fix that define and while we are there, remove some unused defines.
Change some strings in the function to be a bit less wrappy, and
express the correct limits.
Change-ID: I96829bbc77935e0b57c6f0fc1439fb4152b2960a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are seeing situations where the driver sees a hang with less than 4
desc pending, if the driver chooses to ignore it the queue progresses
forward and the stack never experiences a real hang.
With this patch we will log a stat when this situation happens
"tx_sluggish" will increment and we can see some more details
at a higher debug level. Other than that we will ignore this
particular case of Tx hang.
Change-ID: I7d1d1666d990e2b12f4f6bed0d17d22e1b6410d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck