A number of LTE devices from different vendors all suffer from the
same firmware bug: Most of the packets received from the device while
it is attached to a LTE network will not have an ethernet header. The
devices work as expected when attached to 2G or 3G networks, sending
an ethernet header with all packets.
This driver is not aware of which network the modem attached to, and
even if it were there are still some packet types which are always
received with the header intact.
All devices supported by this driver have severely limited
networking capabilities:
- can only transmit IPv4, IPv6 and possibly ARP
- can only support a single host hardware address at any time
- will only do point-to-point communcation with the host
Because of this, we are able to reliably identify any bogus raw IP
packets by simply looking at the 4 IP version bits. All we need to
do is to avoid 4 or 6 in the first digit of the mac address. This
workaround ensures this, and fix up the received packets as necessary.
Given the distribution of the bug, it is believed that the source is
the chipset vendor. The devices which are verified to be affected are:
Huawei E392u-12 (Qualcomm MDM9200)
Pantech UML290 (Qualcomm MDM9600)
Novatel USB551L (Qualcomm MDM9600)
Novatel E362 (Qualcomm MDM9600)
It is believed that the bug depend on firmware revision, which means
that possibly all devices based on the above mentioned chipset may be
affected if we consider all available firmware revisions.
The information about affected devices and versions is likely
incomplete. As the additional overhead for packets not needing this
fixup is very small, it is considered acceptable to apply the
workaround to all devices handled by this driver.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
This patch-set fixes mainly bugs on enslave failure and one occasion
of a needed locking. The patches are:
1. On enslave failure mc addresses are not flushed from the slave
2. On enslave failure vlans are not cleaned up from the slave
3. On enslave failure the bond's primary and curr_active_slave
are not cleaned up (which might result in use of freed memory)
4. On enslave failure netpoll is not disabled which might result in
a memory leak
5. In bond_mc_swap() the bond's mc addr list is walked without
netif_addr_lock, since it can be called without rtnl, add it
v2: patch 01 - fix log message and remove unnecessary code move
====================
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_addr_lock_bh() to acquire the appropriate lock before walking.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave_disable_netpoll() is not called upon enslave failure which would
lead to a memory leak. Call slave_disable_netpoll() after err_detach as
that's the first error path after enabling netpoll on that slave.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On enslave failure primary_slave can point to new_slave which is to be
freed, and the same applies to curr_active_slave. So check if this is
the case and clean up properly after err_detach because that's the first
error code path after they're set.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main problem is with vid refcount which only gets bumped up.
Delete the vlans after err_detach as that's the first error path
after the vlans are added.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.
v2: update log message and don't move code unnecessarily
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -EINVAL when tb[TCA_FW_MASK] is set and head->mask != 0xFFFFFFFF
instead of 0 (ifdef CONFIG_NET_CLS_IND and tb[TCA_FW_INDEV]), as done elsewhere
in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "reason" can come from skb->data[] and it hasn't been capped so it
can be from 0-255 instead of just 0-6. For example in irlmp_state_dtr()
the code does:
reason = skb->data[3];
...
irlmp_disconnect_indication(self, reason, skb);
Also LMREASON has a couple other values which don't have entries in the
irlmp_reasons[] array. And 0xff is a valid reason as well which means
"unknown".
So far as I can see we don't actually care about "reason" except for in
the debug code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Dave Kleikamp, when we emit cross calls to do batched
TLB flush processing we have a race because we do not synchronize on
the sibling cpus completing the cross call.
So meanwhile the TLB batch can be reset (tb->tlb_nr set to zero, etc.)
and either flushes are missed or flushes will flush the wrong
addresses.
Fix this by using generic infrastructure to synchonize on the
completion of the cross call.
This first required getting the flush_tlb_pending() call out from
switch_to() which operates with locks held and interrupts disabled.
The problem is that smp_call_function_many() cannot be invoked with
IRQs disabled and this is explicitly checked for with WARN_ON_ONCE().
We get the batch processing outside of locked IRQ disabled sections by
using some ideas from the powerpc port. Namely, we only batch inside
of arch_{enter,leave}_lazy_mmu_mode() calls. If we're not in such a
region, we flush TLBs synchronously.
1) Get rid of xcall_flush_tlb_pending and per-cpu type
implementations.
2) Do TLB batch cross calls instead via:
smp_call_function_many()
tlb_pending_func()
__flush_tlb_pending()
3) Batch only in lazy mmu sequences:
a) Add 'active' member to struct tlb_batch
b) Define __HAVE_ARCH_ENTER_LAZY_MMU_MODE
c) Set 'active' in arch_enter_lazy_mmu_mode()
d) Run batch and clear 'active' in arch_leave_lazy_mmu_mode()
e) Check 'active' in tlb_batch_add_one() and do a synchronous
flush if it's clear.
4) Add infrastructure for synchronous TLB page flushes.
a) Implement __flush_tlb_page and per-cpu variants, patch
as needed.
b) Likewise for xcall_flush_tlb_page.
c) Implement smp_flush_tlb_page() to invoke the cross-call.
d) Wire up global_flush_tlb_page() to the right routine based
upon CONFIG_SMP
5) It turns out that singleton batches are very common, 2 out of every
3 batch flushes have only a single entry in them.
The batch flush waiting is very expensive, both because of the poll
on sibling cpu completeion, as well as because passing the tlb batch
pointer to the sibling cpus invokes a shared memory dereference.
Therefore, in flush_tlb_pending(), if there is only one entry in
the batch perform a completely asynchronous global_flush_tlb_page()
instead.
Reported-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
cyc_to_sched_clock() is called by sched_clock() and cyc_to_ns()
is called by cyc_to_sched_clock(). I suspect that some compilers
inline both of these functions into sched_clock() and so we've
been getting away without having a notrace marking. It seems that
my compiler isn't inlining cyc_to_sched_clock() though, so I'm
hitting a recursion bug when I enable the function graph tracer,
causing my system to crash. Marking these functions notrace fixes
it. Technically cyc_to_ns() doesn't need the notrace because it's
already marked inline, but let's just add it so that if we ever
remove inline from that function it doesn't blow up.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only one remaining fix for arm-soc platforms at this time, a small
bugfix for cpu hotplug on highbank platforms that has become much
easier to hit as of late. Details in the patch description, but it's
small and well-contained and definitely impacts users of the platform,
so 3.9 seems appropriate.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=j3Hq
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Only one remaining fix for arm-soc platforms at this time, a small
bugfix for cpu hotplug on highbank platforms that has become much
easier to hit as of late.
Details in the patch description, but it's small and well-contained
and definitely impacts users of the platform, so 3.9 seems
appropriate."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: highbank: fix cache flush ordering for cpu hotplug
Pablo Neira Ayuso says:
====================
If time allows, please consider pulling the following patchset contains two
late Netfilter fixes, they are:
* Skip broadcast/multicast locally generated traffic in the rpfilter,
(closes netfilter bugzilla #814), from Florian Westphal.
* Fix missing elements in the listing of ipset bitmap ip,mac set
type with timeout support enabled, from Jozsef Kadlecsik.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
A few stragglers hoping for 3.9, somewhat delayed due to my travels...
On the mac80211 bits, Johannes says:
"Sadly, I have another pull request -- the idle handling fix broke LED
handling in some cases."
and:
"Yet one more!
This fixes a fairly important/annoying bug -- when roaming between
multiple APs of the same network, the system could get stuck thinking it
was connected to the old one while it really wasn't."
On top of that...
Arend sends a brcmfmac patch that removes advertising a feature that
isn't actually fully supported, and a brcmsmac patch that rearranges
code to request firmware at IFF_UP to play more nicely with being
built into the kernel.
Felix gives us a minor ath9k_htc fix to support the newly released
open source firmware, and an ath9k_hw initvals fix to improve device
stability.
Rafał Miłecki provides a fix for an ssb regression that caused a
serious performance problem with b43.
Zefir Kurtisi offers an ath9k fix to change some kmalloc flags to
allow the DFS detector to be called in softirq context.
Please let me know if there are problems. If these don't make 3.9,
I'll just pull them into wireless-next -- just let me know if you
want to do it that way!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bd090dfc63 (tcp: tcp_replace_ts_recent() should not be called
from tcp_validate_incoming()) introduced a TS ecr bug in slow path
processing.
1 A > B P. 1:10001(10000) ack 1 <nop,nop,TS val 1001 ecr 200>
2 B < A . 1:1(0) ack 1 win 257 <sack 9001:10001,TS val 300 ecr 1001>
3 A > B . 1:1001(1000) ack 1 win 227 <nop,nop,TS val 1002 ecr 200>
4 A > B . 1001:2001(1000) ack 1 win 227 <nop,nop,TS val 1002 ecr 200>
(ecr 200 should be ecr 300 in packets 3 & 4)
Problem is tcp_ack() can trigger send of new packets (retransmits),
reflecting the prior TSval, instead of the TSval contained in the
currently processed incoming packet.
Fix this by calling tcp_replace_ts_recent() from tcp_ack() after the
checks, but before the actions.
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is my example conversion of a few existing mmap users. The pcm
mmap case is one of the more straightforward ones.
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is my example conversion of a few existing mmap users. The
fb_mmap() case is a good example because it is a bit more complicated
than some: fb_mmap() mmaps one of two different memory areas depending
on the page offset of the mmap (but happily there is never any mixing of
the two, so the helper function still works).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is my example conversion of a few existing mmap users. The mtdchar
case is actually disabled right now (and stays disabled), but I did it
because it showed up on my "git grep", and I was familiar with the code
due to fixing an overflow problem in the code in commit 9c603e53d3
("mtdchar: fix offset overflow detection").
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is my example conversion of a few existing mmap users. The HPET
case is simple, widely available, and easy to test (Clemens Ladisch sent
a trivial test-program for it).
Test-program-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull input fixes from Dmitry Torokhov:
"Two more small fixups to the wacom driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - fix "can not retrieve extra class descriptor" for DTH2242
Input: wacom - DTH2242 Grip Pen id was off by one bit
Pull fuse build fix from Miklos Szeredi:
"This fixes android builds. The patch appears large, but is just
search & replace."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix type definitions in uapi header
Same as Cintiq 24HDT, DTH2242 has two interfaces sharing one configuration.
This patch ignores the second interface.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull user-namespace fixes from Andy Lutomirski.
* 'userns-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux:
userns: Changing any namespace id mappings should require privileges
userns: Check uid_map's opener's fsuid, not the current fsuid
userns: Don't let unprivileged users trick privileged users into setting the id_map
Pull x86 platform driver revert from Matthew Garrett:
"It turns out that one of the hp-wmi patches this cycle breaks some
other HP laptops. I think we have a good idea how to work on it for
3.10, but it's safer to just revert it for now."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Revert "hp-wmi: Add support for SMBus hotkeys"
Alex Efros reported rpfilter module doesn't match following packets:
IN=br.qemu SRC=192.168.2.1 DST=192.168.2.255 [ .. ]
(netfilter bugzilla #814).
Problem is that network stack arranges for the locally generated broadcasts
to appear on the interface they were sent out, so the IFF_LOOPBACK check
doesn't trigger.
As -m rpfilter is restricted to PREROUTING, we can check for existing
rtable instead, it catches locally-generated broad/multicast case, too.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This reverts commit fabf85e3ca which breaks
hotkey support on some other HP laptops. We'll try doing this differently
in 3.10.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
The type when timeout support was enabled, could not list all elements,
just the first ones which could fit into one netlink message: it just
did not continue listing after the first message.
Reported-by: Yoann JUET <yoann.juet@univ-nantes.fr>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Tested-by: Yoann JUET <yoann.juet@univ-nantes.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit 6b923cb718 (bonding: support for IPv6 transmit hashing)
bonding doesn't properly hash traffic in forwarding setups.
Vitaly V. Bursov diagnosed that skb_network_header_len() returned 0 in
this case.
More generally, the transport header might not be in the skb head.
Use pskb_may_pull() & skb_header_pointer() to get it right, and use
proto_ports_offset() in bond_xmit_hash_policy_l34() to get support for
more protocols than TCP and UDP.
Reported-by: Vitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: John Eaglesham <linux@8192.net>
Tested-by: Vitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes 2 issues regarding bnx2x's status blocks:
1. ethtool -c caused corruption of status blocks in FW RAM.
2. when using multi-CoS, the configuration of the timeout values of
status blocks is incorrect, harming the coalescing of interrupts
for such CoSs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading after UNDI (e.g., Boot from SAN) the UNDI does not
gracefully yield its resources; The bnx2x driver handles that release
itself.
During the manipulation required to release those resources, it's possible
for the UNDI to try and write to memory regions which are no longer accessible,
causing the PCI bus to prevent further writes from the chip.
This would in turn cause DMAE timeouts later on in the driver, as the driver
will be unable to use the chip's DMA engines.
This patch prevents the chip from actually writing through the PCI bus
in said scenario, thus allowing the release without the unfortunate by-product.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh says:
====================
This patch series contains bug fixes for -
* Loopback test failure while traffic is running.
* Tx timeout and subsequent firmware reset by removing check for
'(adapter->netdev->features & (NETIF_F_TSO | NETIF_F_TSO6)' from tx fast
path, as per Eric's suggestion.
* Typo in logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o Debug logs were not matching with code functionality.
o Changed dev_info to netdev_err
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver receives a packet with gso size > 0 and when TSO is disabled,
it should be transmitted as a TSO packet to prevent Tx timeout and subsequent
firmware reset.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before conducting loopback test by sending packets, driver should stop transmit
queue and turn off carrier.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF driver does not check if the administrator has already set a VF
VLAN via the PF driver before setting the new VLAN. This results in
the following scenario:
A) Administrator sets VF <n> to VLAN 100
B) Administrator sets VF <x> to VLAN 100
C) Administrator sets VF <n> to VLAN 200
D) The VF <n> driver continues to be able to receive traffic on VLAN
100 because the VLVFB pool enable bit for that VF was left set
instead of being cleared as it should be.
This fix ensures that the old VLAN filter for VF <n> is first removed
and the pool bit enable for VF <n> is cleared so that it no longer
receives traffic on VLAN 100.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch actually reverts:
igb: Support using build_skb in the case that jumbo frames are disabled
The reason for reverting this patch is that it can lead to data corruption.
The following flow was pointed out by Ben Hutchings:
1. skb is forwarded to another device
2. Packet headers are modified and it's put into a queue
3. Second packet is received into the other half of this page
4. Page cannot be reused, so is DMA-unmapped
5. The DMA mapping was non-coherent, so unmap copies or invalidates
cache
The headers added in step 2 get trashed in step 5.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix MAC address check in case of multiple mesh interfaces
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=oL+V
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- fix MAC address check in case of multiple mesh interfaces
Signed-off-by: David S. Miller <davem@davemloft.net>
The L1 data cache flush needs to be after highbank_set_cpu_jump call which
pollutes the cache with the l2x0_lock. This causes other cores to deadlock
waiting for the l2x0_lock. Moving the flush of the entire data cache after
highbank_set_cpu_jump fixes the problem. Use flush_cache_louis instead of
flush_cache_all are that is sufficient to flush only the L1 data cache.
flush_cache_louis did not exist when highbank_cpu_die was originally
written.
With PL310 errata 769419 enabled, a wmb is inserted into idle which takes
the l2x0_lock. This makes the problem much more easily hit and causes
reset to hang.
Reported-by: Paolo Pisati <p.pisati@gmail.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit 3a366e614d.
Wanlong Gao reports that it causes a kernel panic on his machine several
minutes after boot. Reverting it removes the panic.
Jens says:
"It's not quite clear why that is yet, so I think we should just revert
the commit for 3.9 final (which I'm assuming is pretty close).
The wifi is crap at the LSF hotel, so sending this email instead of
queueing up a revert and pull request."
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Requested-by: Jens Axboe <axboe@kernel.dk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Install the Hyper-V specific interrupt handler only when needed. This would
permit us to get rid of the Xen check. Note that when the vmbus drivers invokes
the call to register its handler, we are sure to be running on Hyper-V.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Link: http://lkml.kernel.org/r/1366299886-6399-1-git-send-email-kys@microsoft.com
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fix a double locking bug caused when debug.kprobe-optimization=0.
While the proc_kprobes_optimization_handler locks kprobe_mutex,
wait_for_kprobe_optimizer locks it again and that causes a double lock.
To fix the bug, this introduces different mutex for protecting
sysctl parameter and locks it in proc_kprobes_optimization_handler.
Of course, since we need to lock kprobe_mutex when touching kprobes
resources, that is done in *optimize_all_kprobes().
This bug was introduced by commit ad72b3bea7 ("kprobes: fix
wait_for_kprobe_optimizer()")
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The BUG_ON() directive is triggered probably due to a latency
modification following inclusion of commit c10d73671a ("softirq:
reduce latencies"). This condition has not been met before 3.9-rc1 and
doesn't trigger without this patch.
We now make sure that DMA channel is idle before calling
atc_complete_all() which makes the BUG_ON() "protection" useless.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesse Gross says:
====================
Two small bug fixes for net/3.9 including the issue previously
discussed where allocation of netlink notifications can fail after
changes have been committed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull idle patches from Len Brown:
"A pair of small patches for 3.9-rc7.
This CPU-id should have been included in the ones that we updated
earlier in 3.9. This pair of patches will allow this flavor of
Haswell to behave like the other flavors."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: additional Haswell CPU-id
intel_idle: additional Haswell CPU-id
This fixes a kernel memory contents leak via the tkill and tgkill syscalls
for compat processes.
This is visible in the siginfo_t->_sifields._rt.si_sigval.sival_ptr field
when handling signals delivered from tkill.
The place of the infoleak:
int copy_siginfo_to_user32(compat_siginfo_t __user *to, siginfo_t *from)
{
...
put_user_ex(ptr_to_compat(from->si_ptr), &to->si_ptr);
...
}
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Reviewed-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the error return value in kswapd_run(). The bug was introduced by
commit d5dc0ad928 ("mm/vmscan: fix error number for failed kthread").
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
