[ Upstream commit f141a42215 ]
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not called in
error handling paths. Call pm_runtime_put if pm_runtime_get_sync fails.
Fixes: fc05a5b222 ("ASoC: rockchip: add support for pdm controller")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200613205158.27296-1-wu000273@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed1220df6e ]
For mono channel, SSI will switch to Normal mode.
In Normal mode and Network mode, the Word Length Control bits
control the word length divider in clock generator, which is
different with I2S Master mode (the word length is fixed to
32bit), it should be the value of params_width(hw_params).
The condition "slots == 2" is not good for I2S Master mode,
because for Network mode and Normal mode, the slots can also
be 2. Then we need to use (ssi->i2s_net & SSI_SCR_I2S_MODE_MASK)
to check if it is I2S Master mode.
So we refine the formula for mono channel, otherwise there
will be sound issue for S24_LE.
Fixes: b0a7043d5c ("ASoC: fsl_ssi: Caculate bit clock rate using slot number and width")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/034eff1435ff6ce300b6c781130cefd9db22ab9a.1592276147.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a212008925 ]
Currently both FE and BE dai-links are configured bi-directional,
However the DSP BE dais are only single directional,
so set the directions as supported by the BE dais.
Fixes: c25e295cd7 (ASoC: qcom: Add support to parse common audio device nodes)
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200612123711.29130-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a95737440 ]
This patch adds support to q6afe_is_rx_port() to get direction
of DSP BE dai port, this is useful for setting dailink
directions correctly.
Fixes: c25e295cd7 (ASoC: qcom: Add support to parse common audio device nodes)
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200612123711.29130-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6476b60f32 ]
Successful send of EOS command does not indicate that EOS is actually
finished, correct event to wait EOS is finished is EOS_RENDERED event.
EOS_RENDERED means that the DSP has finished processing all the buffers
for that particular session and stream.
This patch fixes EOS handling!
Fixes: 68fd8480bb ("ASoC: qdsp6: q6asm: Add support to audio stream apis")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200611124159.20742-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79d4f823a0 ]
The Asus T101HA uses the default jack-detect mode 3, but instead of
using an analog microphone it is using a DMIC on dmic-data-pin 1,
like the Asus T100HA. Note unlike the T100HA its jack-detect is not
inverted.
Add a DMI quirk with the correct settings for this model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200608204634.93407-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 199a5e8fda ]
The Toshiba Encore WT10-A tablet almost fully works with the default
settings for Bay Trail CR devices. The only issue is that it uses a
digital mic. connected the the DMIC1 input instead of an analog mic.
Add a quirk for this model using the default settings with the input-map
replaced with BYT_RT5640_DMIC1_MAP.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200608204634.93407-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba4e5abc6c ]
With additional checks on dailinks, we see errors such as
[ 3.000418] sof-nocodec sof-nocodec: CPU DAI DMIC01 Pin for rtd
NoCodec-6 does not support playback
It's not clear why we set the dpcm_playback and dpcm_capture flags
unconditionally, add a check on number of channels for each direction
to avoid invalid configurations.
Fixes: 8017b8fd37 ('ASoC: SOF: Add Nocodec machine driver support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200608194415.4663-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 607fa205a7 ]
Additional checks for valid DAIs expose a corner case, where existing
BE dailinks get modified, e.g. HDMI links are tagged with
dpcm_capture=1 even if the DAIs are for playback.
This patch makes those changes conditional and flags configuration
issues when a BE dailink is has no_pcm=0 but dpcm_playback or
dpcm_capture=1 (which makes no sense).
As discussed on the alsa-devel mailing list, there are redundant flags
for dpcm_playback, dpcm_capture, playback_only, capture_only. This
will have to be cleaned-up in a future update. For now only correct
and flag problematic configurations.
Fixes: 218fe9b7ec ("ASoC: soc-core: Set dpcm_playback / dpcm_capture")
Suggested-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200608194415.4663-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36124fb19f ]
fsl_asrc_dma_hw_params() invokes dma_request_channel() or
fsl_asrc_get_dma_channel(), which returns a reference of the specified
dma_chan object to "pair->dma_chan[dir]" with increased refcnt.
The reference counting issue happens in one exception handling path of
fsl_asrc_dma_hw_params(). When config DMA channel failed for Back-End,
the function forgets to decrease the refcnt increased by
dma_request_channel() or fsl_asrc_get_dma_channel(), causing a refcnt
leak.
Fix this issue by calling dma_release_channel() when config DMA channel
failed.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/1590415966-52416-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25bf943e4e ]
Function "pm_runtime_get_sync()" is not handled by "pm_runtime_put()"
if "PTR_ERR(rst) == -EPROBE_DEFER". Fix this issue by adding
"pm_runtime_put()" into this error path.
Fixes: f65bb92ca1 ("ASoC: img-i2s-in: Add runtime PM")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Link: https://lore.kernel.org/r/20200525055011.31925-1-wu000273@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e0e10fde0 ]
The Toshiba Encore WT8-A tablet almost fully works with the default
settings for non-CR Bay Trail devices. The only problem is that its
jack-detect switch is not inverted (it is active high instead of
the normal active low).
Add a quirk for this model using the default settings +
BYT_RT5640_JD_NOT_INV.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200518072416.5348-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03990fd58d ]
If an error occurs after the call to 'omap_mcbsp_init()', the reference to
'mcbsp->fclk' must be decremented, as already done in the remove function.
This can be achieved easily by using the devm_ variant of 'clk_get()'
when the reference is taken in 'omap_mcbsp_init()'
This fixes the leak in the probe and has the side effect to simplify both
the error handling path of 'omap_mcbsp_init()' and the remove function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Link: https://lore.kernel.org/r/20200512134325.252073-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e8748fcae ]
There are 2 issues here:
- if one of the 'of_parse_phandle' fails, calling 'mop500_of_node_put()'
is a no-op because the 'mop500_dai_links' structure has not been
initialized yet, so the referenced are not decremented
- The reference stored in 'mop500_dai_links[i].codecs' is refcounted
only once in the probe and must be decremented only once.
Fixes: 39013bd60e ("ASoC: Ux500: Dispose of device nodes correctly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200512100705.246349-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66c705d07d ]
SSI BUSIF buffer is possible to overflow or underflow, especially in a
hypervisor environment. If there is no interrupt support, it will eventually
lead to errors in pcm data.
This patch adds overflow and underflow interrupt support for SSI BUSIF buffer.
Reported-by: Chen Li <licheng0822@thundersoft.com>
Signed-off-by: Yongbo Zhang <giraffesnn123@gmail.com>
Tested-by: Chen Li <licheng0822@thundersoft.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200512093003.28332-1-giraffesnn123@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d8785bc7a ]
Fix to return negative error code -ENOMEM from the IPC init error
handling case instead of 0, as done elsewhere in this function.
Fixes: c16211d622 ("ASoC: SOF: Add Sound Open Firmware driver core")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200509093337.78897-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a446873d7 ]
During S3 test, the following error was observed:
[ 726.174237] i2c_designware i2c_designware.0: platform_pm_resume+0x0/0x3d returned 0 after 0 usecs
[ 726.184187] max98373 i2c-MX98373:00: calling max98373_resume+0x0/0x30 [snd_soc_max98373] @ 12698, parent: i2c-11
[ 726.195589] max98373 i2c-MX98373:00: Reset command failed. (ret:-16)
When calling regmap_update_bits(), since map->reg_update_bits is NULL,
_regmap_read() is entered with the following logic:
if (!map->cache_bypass) {
ret = regcache_read(map, reg, val);
if (ret == 0)
return 0;
}
if (map->cache_only)
return -EBUSY;
regcache_read() hits -EINVAL because MAX98373_R2000_SW_RESET is volatile,
as map->cache_only is set by codec suspend, thus -EBUSY is returned.
Fix by moving max98373_reset() after cache_only set to false in max98373_resume().
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Link: https://lore.kernel.org/r/1588376661-29799-1-git-send-email-yong.zhi@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b8a299a58 ]
free_irq() is missing in case of error, fix that.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200606153103.GA17905@amd
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c26fde3b15 ]
This provides a better separation between runtime and PM sleep
callbacks.
Only do nothing if given runtime flag is set and calback is not set.
With the current implementation, if PM sleep callback is set but runtime
callback is not set then at runtime resume we reload the firmware even
if we do not support runtime resume callback.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200515135958.17511-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a697ae6ea5 ]
davinci_mcasp_get_dma_type() invokes dma_request_chan(), which returns a
reference of the specified dma_chan object to "chan" with increased
refcnt.
When davinci_mcasp_get_dma_type() returns, local variable "chan" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
davinci_mcasp_get_dma_type(). When chan device is NULL, the function
forgets to decrease the refcnt increased by dma_request_chan(), causing
a refcnt leak.
Fix this issue by calling dma_release_channel() when chan device is
NULL.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/1587818916-38730-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fecbb71fe ]
Disable exception interrupt before scheduling tasklet, otherwise if
the tasklet isn't handled immediately, there will be endless xrun
interrupt.
Fixes: 7ccafa2b38 ("ASoC: fsl_esai: recover the channel swap after xrun")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/a8f2ad955aac9e52587beedc1133b3efbe746895.1587968824.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe17e6cdc0 ]
when do randconfig like this:
CONFIG_SND_SOC_SOF_IMX8_SUPPORT=y
CONFIG_SND_SOC_SOF_IMX8=y
CONFIG_SND_SOC_SOF_OF=y
CONFIG_IMX_DSP=m
CONFIG_IMX_SCU=y
there is a link error:
sound/soc/sof/imx/imx8.o: In function 'imx8_send_msg':
imx8.c:(.text+0x380): undefined reference to 'imx_dsp_ring_doorbell'
Select IMX_DSP in SND_SOC_SOF_IMX8_SUPPORT to fix this
Fixes: f9ad754684 ("ASoC: SOF: imx: fix reverse CONFIG_SND_SOC_SOF_OF dependency")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20200409071832.2039-2-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ef9d5073b ]
The microphone-jack state needs to be masked in a case of a 4-pin jack
when microphone and ground pins are shorted. Presence of nvidia,headset
tells that WM8903 CODEC driver should mask microphone's status if short
circuit is detected, i.e headphones are inserted.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200330204011.18465-3-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8ba4dc3cff upstream.
The xmax values for Master Playback Volume and Mic Boost
Capture Volume are specified incorrectly (one greater)
which results in the wrong dB gain being shown to the user
in the case of Master Playback Volume.
Signed-off-by: Pavel Dobias <dobias@2n.cz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200515120757.24669-1-dobias@2n.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d745cc1ab6 ]
Those strings are exposed to the user space as the
card name thus used in the GUIs. The common
standard is to avoid '_' here. The worst case
is 'sof-skl_hda_card' string.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191028164624.14334-1-perex@perex.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54cb622168 ]
Fix the rsnd_ssi_stop function to skip disabling the individual SSIs of
a multi-SSI setup, as the actual stop is performed by rsnd_ssiu_stop_gen2
- the same logic as in rsnd_ssi_start. The attempt to disable these SSIs
was harmless, but caused a "status check failed" message to be printed
for every SSI in the multi-SSI setup.
The disabling of interrupts is still performed, as they are enabled for
all SSIs in rsnd_ssi_init, but care is taken to not accidentally set the
EN bit for an SSI where it was not set by rsnd_ssi_start.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200417153017.1744454-3-matthias.blankertz@cetitec.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c258657dd ]
The master SSI of a multi-SSI setup was attached both to the
RSND_MOD_SSI slot and the RSND_MOD_SSIP slot of the rsnd_dai_stream.
This is not correct wrt. the meaning of being "parent" in the rest of
the SSI code, where it seems to indicate an SSI that provides clock and
word sync but is not transmitting/receiving audio data.
Not treating the multi-SSI master as parent allows removal of various
special cases to the rsnd_ssi_is_parent conditions introduced in commit
a09fb3f28a ("ASoC: rsnd: Fix parent SSI start/stop in multi-SSI mode").
It also fixes the issue that operations performed via rsnd_dai_call()
were performed twice for the master SSI. This caused some "status check
failed" spam when stopping a multi-SSI stream as the driver attempted to
stop the master SSI twice.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200417153017.1744454-2-matthias.blankertz@cetitec.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 326b509238 ]
If we don't find any pcm, pcm will point at address at an offset from
the the list head and not a meaningful structure. Fix this by returning
correct pcm if found and NULL if not. Found with coccinelle.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20200415162849.308-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b94e164759 ]
The HDMI?_SEL register maps up to four stereo SSI data lanes onto the
sdata[0..3] inputs of the HDMI output block. The upper half of the
register contains four blocks of 4 bits, with the most significant
controlling the sdata3 line and the least significant the sdata0 line.
The shift calculation has an off-by-one error, causing the parent SSI to
be mapped to sdata3, the first multi-SSI child to sdata0 and so forth.
As the parent SSI transmits the stereo L/R channels, and the HDMI core
expects it on the sdata0 line, this causes no audio to be output when
playing stereo audio on a multichannel capable HDMI out, and
multichannel audio has permutated channels.
Fix the shift calculation to map the parent SSI to sdata0, the first
child to sdata1 etc.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200415141017.384017-3-matthias.blankertz@cetitec.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a09fb3f28a ]
The parent SSI of a multi-SSI setup must be fully setup, started and
stopped since it is also part of the playback/capture setup. So only
skip the SSI (as per commit 203cdf51f2 ("ASoC: rsnd: SSI parent cares
SWSP bit") and commit 597b046f0d ("ASoC: rsnd: control SSICR::EN
correctly")) if the SSI is parent outside of a multi-SSI setup.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200415141017.384017-2-matthias.blankertz@cetitec.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26d8788159 ]
As done in already existing cases, we should use le32_to_cpu macro while
accessing hdr->magic. Found with sparse.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20200415162435.31859-2-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa7812737f ]
As mentioned slightly out of patch context in the code, there
is no reset routine for the chip. On boards where the chip is
supplied by a fixed regulator, it might not even be resetted
during (e.g. watchdog) reboot and can be in any state.
If the device is probed with VAG enabled, the driver's probe
routine will generate a loud pop sound when ANA_POWER is
being programmed. Avoid this by properly disabling just the
VAG bit and waiting the required power down time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Fabio Estevam <festivem@gmail.com>
Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3677fc3d6 ]
Function pcm_new_ver can fail, so we should check it's return value and
handle possible error.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200327204729.397-6-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6856e887ea ]
Function soc_tplg_add_route can propagate error code from callback, we
should check its return value and handle fail in correct way.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200327204729.397-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ae548f30d ]
Functions soc_tplg_denum_create, soc_tplg_dmixer_create,
soc_tplg_dbytes_create can fail, so their return values should be
checked and error should be propagated.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200327204729.397-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 482db55ae8 ]
Function soc_tplg_create_tlv can fail, so we should check if it succeded
or not and proceed appropriately.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200327204729.397-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 005aa9f0af which is
commit 1164284270 upstream.
It should not have been backported, I only looked at the "Fixes:" tag,
not the changelog text itself, my fault.
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a22ae72b86 upstream.
v5.4 changes in soc-core tightened the checks on soc_dapm_add_routes,
which results in the ASoC card probe failing.
Introduce a flag to be set in machine drivers to prevent the probe
from stopping in case of incomplete topologies or missing routes. This
flag is for backwards compatibility only and shall not be used for
newer machine drivers.
Example with an HDaudio card with a bad topology:
[ 236.177898] skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: Failed to
add route iDisp1_out -> direct -> iDisp1 Tx
[ 236.177902] skl_hda_dsp_generic skl_hda_dsp_generic:
snd_soc_bind_card: snd_soc_dapm_add_routes failed: -19
with the disable_route_checks set:
[ 64.031657] skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: Failed to
add route iDisp1_out -> direct -> iDisp1 Tx
[ 64.031661] skl_hda_dsp_generic skl_hda_dsp_generic:
snd_soc_bind_card: disable_route_checks set, ignoring errors on
add_routes
Fixes: daa480bde6 ("ASoC: soc-core: tidyup for snd_soc_dapm_add_routes()")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200309192744.18380-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e060a453c upstream.
After suspend & resume, wm8960_hw_params may be called when
bias_level is not SND_SOC_BIAS_ON, then wm8960_configure_clocking
is not called. But if sample rate is changed at that time, then
the output clock rate will be not correct.
So judgement of bias_level is SND_SOC_BIAS_ON in wm8960_hw_params
is not necessary and it causes above issue.
Fixes: 3176bf2d7c ("ASoC: wm8960: update pll and clock setting function")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1587468525-27514-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1164284270 upstream.
Since the addition of commit 9b5db05936 ("ASoC: soc-pcm: dpcm: Only allow
playback/capture if supported"), meson-axg cards which have codec-to-codec
links fail to init and Oops:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000128
Internal error: Oops: 96000044 [#1] PREEMPT SMP
CPU: 3 PID: 1582 Comm: arecord Not tainted 5.7.0-rc1
pc : invalidate_paths_ep+0x30/0xe0
lr : snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8
Call trace:
invalidate_paths_ep+0x30/0xe0
snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8
dpcm_path_get+0x38/0xd0
dpcm_fe_dai_open+0x70/0x920
snd_pcm_open_substream+0x564/0x840
snd_pcm_open+0xfc/0x228
snd_pcm_capture_open+0x4c/0x78
snd_open+0xac/0x1a8
...
While initiliazing the links, ASoC treats the codec-to-codec links of this
card type as a DPCM backend. This error eventually leads to the Oops.
Most of the card driver code is shared between DPCM backends and
codec-to-codec links. The property "no_pcm" marking DCPM BE was left set on
codec-to-codec links, leading to this problem. This commit fixes that.
Fixes: 0a8f1117a6 ("ASoC: meson: axg-card: add basic codec-to-codec link support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200420114511.450560-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9df8ba7c63 upstream.
If probe fails after enabling the regulators regulator_put is called for
each supply without having them disabled before. This produces some
warnings like
WARNING: CPU: 0 PID: 90 at drivers/regulator/core.c:2044 _regulator_put.part.0+0x154/0x15c
[<c010f7a8>] (unwind_backtrace) from [<c010c544>] (show_stack+0x10/0x14)
[<c010c544>] (show_stack) from [<c012b640>] (__warn+0xd0/0xf4)
[<c012b640>] (__warn) from [<c012b9b4>] (warn_slowpath_fmt+0x64/0xc4)
[<c012b9b4>] (warn_slowpath_fmt) from [<c04c4064>] (_regulator_put.part.0+0x154/0x15c)
[<c04c4064>] (_regulator_put.part.0) from [<c04c4094>] (regulator_put+0x28/0x38)
[<c04c4094>] (regulator_put) from [<c04c40cc>] (regulator_bulk_free+0x28/0x38)
[<c04c40cc>] (regulator_bulk_free) from [<c0579b2c>] (release_nodes+0x1d0/0x22c)
[<c0579b2c>] (release_nodes) from [<c05756dc>] (really_probe+0x108/0x34c)
[<c05756dc>] (really_probe) from [<c0575aec>] (driver_probe_device+0xb8/0x16c)
[<c0575aec>] (driver_probe_device) from [<c0575d40>] (device_driver_attach+0x58/0x60)
[<c0575d40>] (device_driver_attach) from [<c0575da0>] (__driver_attach+0x58/0xcc)
[<c0575da0>] (__driver_attach) from [<c0573978>] (bus_for_each_dev+0x78/0xc0)
[<c0573978>] (bus_for_each_dev) from [<c0574b5c>] (bus_add_driver+0x188/0x1e0)
[<c0574b5c>] (bus_add_driver) from [<c05768b0>] (driver_register+0x74/0x108)
[<c05768b0>] (driver_register) from [<c061ab7c>] (i2c_register_driver+0x3c/0x88)
[<c061ab7c>] (i2c_register_driver) from [<c0102df8>] (do_one_initcall+0x58/0x250)
[<c0102df8>] (do_one_initcall) from [<c01a91bc>] (do_init_module+0x60/0x244)
[<c01a91bc>] (do_init_module) from [<c01ab5a4>] (load_module+0x2180/0x2540)
[<c01ab5a4>] (load_module) from [<c01abbd4>] (sys_finit_module+0xd0/0xe8)
[<c01abbd4>] (sys_finit_module) from [<c01011e0>] (__sys_trace_return+0x0/0x20)
Fixes: 3fd6e7d9a1 (ASoC: tas571x: New driver for TI TAS571x power amplifiers)
Signed-off-by: Philipp Puschmann <p.puschmann@pironex.de>
Link: https://lore.kernel.org/r/20200414112754.3365406-1-p.puschmann@pironex.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c824ec094 upstream.
For some reason, the MI2S DAIs do not have channels_min/max defined.
This means that snd_soc_dai_stream_valid() returns false,
i.e. the DAIs have neither valid playback nor capture stream.
It's quite surprising that this ever worked correctly,
but in 5.7-rc1 this is now failing badly: :)
Commit 0e9cf4c452 ("ASoC: pcm: check if cpu-dai supports a given stream")
introduced a check for snd_soc_dai_stream_valid() before calling
hw_params(), which means that the q6i2s_hw_params() function
was never called, eventually resulting in:
qcom-q6afe aprsvc:q6afe:4:4: no line is assigned
... even though "qcom,sd-lines" is set in the device tree.
Commit 9b5db05936 ("ASoC: soc-pcm: dpcm: Only allow playback/capture if supported")
now even avoids creating PCM devices if the stream is not supported,
which means that it is failing even earlier with e.g.:
Primary MI2S: ASoC: no backend playback stream
Avoid all that trouble by adding channels_min/max for the MI2S DAIs.
Fixes: 24c4cbcfac ("ASoC: qdsp6: q6afe: Add q6afe dai driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200415150050.616392-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebf1474745 upstream.
snd_soc_dapm_kcontrol widget which is created by autodisable control
should contain correct on_val, mask and shift because it is set when the
widget is powered and changed value is applied on registers by following
code in dapm_seq_run_coalesced().
mask |= w->mask << w->shift;
if (w->power)
value |= w->on_val << w->shift;
else
value |= w->off_val << w->shift;
Shift on the mask in dapm_kcontrol_data_alloc() is removed to prevent
double shift.
And, on_val in dapm_kcontrol_set_value() is modified to get correct
value in the dapm_seq_run_coalesced().
Signed-off-by: Gyeongtaek Lee <gt82.lee@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/000001d61537$b212f620$1638e260$@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e6110114d1 ]
Check if DMA pages were successfully allocated in initialization
before calling free. For many types of memory (like sgbufs)
the extra free is harmless, but not all backends track allocation
state, so add an explicit check.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200124213625.30186-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8b78f24c1 ]
The MPMAN MPWIN895CL tablet almost fully works with out default settings.
The only problem is that it has only 1 speaker so any sounds only playing
on the right channel get lost.
Add a quirk for this model using the default settings + MONO_SPEAKER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200405133726.24154-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pierre-Louis Bossart