commit e1e047ace8 upstream.
Commit 2abb0d5268 ("PM / devfreq: Lock devfreq in trans_stat_show")
revealed a missing locking while calling devfreq_update_status() function
during suspend/resume cycle.
Code analysis revealed that devfreq_set_target() function was called
without needed locks held for setting device specific suspend_freq if such
has been defined. This patch fixes that by adding the needed locking, what
fixes following kernel warning on Exynos4412-based OdroidU3 board during
system suspend:
PM: suspend entry (deep)
Filesystems sync: 0.002 seconds
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1385 at drivers/devfreq/devfreq.c:204 devfreq_update_status+0xc0/0x188
Modules linked in:
CPU: 2 PID: 1385 Comm: rtcwake Not tainted 5.4.0-rc6-next-20191111 #6848
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0112588>] (unwind_backtrace) from [<c010e070>] (show_stack+0x10/0x14)
[<c010e070>] (show_stack) from [<c0afb010>] (dump_stack+0xb4/0xe0)
[<c0afb010>] (dump_stack) from [<c01272e0>] (__warn+0xf4/0x10c)
[<c01272e0>] (__warn) from [<c01273a8>] (warn_slowpath_fmt+0xb0/0xb8)
[<c01273a8>] (warn_slowpath_fmt) from [<c07d105c>] (devfreq_update_status+0xc0/0x188)
[<c07d105c>] (devfreq_update_status) from [<c07d2d70>] (devfreq_set_target+0xb0/0x15c)
[<c07d2d70>] (devfreq_set_target) from [<c07d3598>] (devfreq_suspend+0x2c/0x64)
[<c07d3598>] (devfreq_suspend) from [<c05de0b0>] (dpm_suspend+0xa4/0x57c)
[<c05de0b0>] (dpm_suspend) from [<c05def74>] (dpm_suspend_start+0x98/0xa0)
[<c05def74>] (dpm_suspend_start) from [<c0195b58>] (suspend_devices_and_enter+0xec/0xc74)
[<c0195b58>] (suspend_devices_and_enter) from [<c0196a20>] (pm_suspend+0x340/0x410)
[<c0196a20>] (pm_suspend) from [<c019480c>] (state_store+0x6c/0xc8)
[<c019480c>] (state_store) from [<c033fc50>] (kernfs_fop_write+0x10c/0x228)
[<c033fc50>] (kernfs_fop_write) from [<c02a6d3c>] (__vfs_write+0x30/0x1d0)
[<c02a6d3c>] (__vfs_write) from [<c02a9afc>] (vfs_write+0xa4/0x180)
[<c02a9afc>] (vfs_write) from [<c02a9d58>] (ksys_write+0x60/0xd8)
[<c02a9d58>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed3d7fa8 to 0xed3d7ff0)
...
irq event stamp: 9667
hardirqs last enabled at (9679): [<c0b1e7c4>] _raw_spin_unlock_irq+0x20/0x58
hardirqs last disabled at (9698): [<c0b16a20>] __schedule+0xd8/0x818
softirqs last enabled at (9694): [<c01026fc>] __do_softirq+0x4fc/0x5fc
softirqs last disabled at (9719): [<c012fe68>] irq_exit+0x16c/0x170
---[ end trace 41ac5b57d046bdbc ]---
------------[ cut here ]------------
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66d0e797bf upstream.
This reverts commit 4585fbcb53.
The name changing as devfreq(X) breaks some user space applications,
such as Android HAL from Unisoc and Hikey [1].
The device name will be changed unexpectly after every boot depending
on module init sequence. It will make trouble to setup some system
configuration like selinux for Android.
So we'd like to revert it back to old naming rule before any better
way being found.
[1] https://lkml.org/lkml/2018/5/8/1042
Cc: John Stultz <john.stultz@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Orson Zhai <orson.unisoc@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eff5d31f74 ]
To build test, add COMPILE_TEST depedency to both ARM_RK3399_DMC_DEVFREQ
and DEVFREQ_EVENT_ROCKCHIP_DFI configuration. And ARM_RK3399_DMC_DEVFREQ
used the SMCCC interface so that add HAVE_ARM_SMCCC dependency to prevent
the build break.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4556f5e99 ]
Putting a 'struct devfreq_event_dev' object on the stack is generally
a bad idea and here it leads to a warnig about potential stack overflow:
drivers/devfreq/event/exynos-ppmu.c:643:12: error: stack frame size of 1040 bytes in function 'exynos_ppmu_probe' [-Werror,-Wframe-larger-than=]
There is no real need for the device structure, only the string inside
it, so add an internal helper function that simply takes the string
as its argument and remove the device structure.
Fixes: 1dd62c66d3 ("PM / devfreq: events: extend events by type of counted data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[cw00.choi: Fix the issue from 'desc->name' to 'desc[j].name']
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2fee1a7cc6 upstream.
The commit 4585fbcb53 ("PM / devfreq: Modify the device name as devfreq(X) for
sysfs") changed the node name to devfreq(x). After this commit, it is not
possible to get the device name through /sys/class/devfreq/devfreq(X)/*.
Add new name attribute in order to get device name.
Cc: stable@vger.kernel.org
Fixes: 4585fbcb53 ("PM / devfreq: Modify the device name as devfreq(X) for sysfs")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d68adc8f85 upstream.
The governor is initialized after sysfs attributes become visible so in
theory the governor field can be NULL here.
Fixes: bcf23c79c4 ("PM / devfreq: Fix available_governor sysfs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42a6b25e67 ]
Right now devfreq_dev_release will print a warning and abort the rest of
the cleanup if the devfreq instance is not part of the global
devfreq_list. But this is a valid scenario, for example it can happen if
the governor can't be found or on any other init error that happens
after device_register.
Initialize devfreq->node to an empty list head in devfreq_add_device so
that list_del becomes a safe noop inside devfreq_dev_release and we can
continue the rest of the cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7cc792d00 ]
The devfreq_notifier_call functions will update scaling_min_freq and
scaling_max_freq when the OPP table is updated.
If fetching the maximum frequency fails then scaling_max_freq remains
set to zero which is confusing. Set to ULONG_MAX instead so we don't
need special handling for this case in other places.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e876e710ed ]
Notifier callbacks shouldn't return negative errno but one of the
NOTIFY_OK/DONE/BAD values.
The OPP core will ignore return values from notifiers but returning a
value that matches NOTIFY_STOP_MASK will stop the notification chain.
Fix by always returning NOTIFY_OK.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2abb0d5268 upstream.
There is no locking in this sysfs show function so stats printing can
race with a devfreq_update_status called as part of freq switching or
with initialization.
Also add an assert in devfreq_update_status to make it clear that lock
must be held by caller.
Fixes: 39688ce6fa ("PM / devfreq: account suspend/resume for stats")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent commit of
PM / devfreq: passive: Use non-devm notifiers
had incurred compiler warning, "unused variable 'dev'".
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The devfreq passive governor registers and unregisters devfreq
transition notifiers on DEVFREQ_GOV_START/GOV_STOP using devm wrappers.
If devfreq itself is registered with devm then a warning is triggered on
rmmod from devm_devfreq_unregister_notifier. Call stack looks like this:
devm_devfreq_unregister_notifier+0x30/0x40
devfreq_passive_event_handler+0x4c/0x88
devfreq_remove_device.part.8+0x6c/0x9c
devm_devfreq_dev_release+0x18/0x20
release_nodes+0x1b0/0x220
devres_release_all+0x78/0x84
device_release_driver_internal+0x100/0x1c0
driver_detach+0x4c/0x90
bus_remove_driver+0x7c/0xd0
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
imx_devfreq_platdrv_exit+0x14/0xd40 [imx_devfreq]
This happens because devres_release_all will first remove all the nodes
into a separate todo list so the nested devres_release from
devm_devfreq_unregister_notifier won't find anything.
Fix the warning by calling the non-devm APIS for frequency notification.
Using devm wrappers is not actually useful for a governor anyway: it
relies on the devfreq core to correctly match the GOV_START/GOV_STOP
notifications.
Fixes: 996133119f ("PM / devfreq: Add new passive governor")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reuse opp core code for setting bus clock and voltage. As a side
effect this allow usage of coupled regulators feature (required
for boards using Exynos5422/5800 SoCs) because dev_pm_opp_set_rate()
uses regulator_set_voltage_triplet() for setting regulator voltage
while the old code used regulator_set_voltage_tol() with fixed
tolerance. This patch also removes no longer needed parsing of DT
property "exynos,voltage-tolerance" (no Exynos devfreq DT node uses
it). After applying changes both functions exynos_bus_passive_target()
and exynos_bus_target() have the same code, so remove
exynos_bus_passive_target(). In exynos_bus_probe() replace it with
exynos_bus_target.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Regulators should be enabled before clocks to avoid h/w hang. This
require change in exynos_bus_probe() to move exynos_bus_parse_of()
after exynos_bus_parent_parse_of() and change in error handling.
Similar change is needed in exynos_bus_exit() where clock should be
disabled before regulators.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Correct the documentation for devm_devfreq_remove_device() argument.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds posibility to choose what type of data should be counted
by the PPMU counter. Now the type comes from DT where the event has been
defined. When there is no 'event-data-type' the default value is used,
which is 'read+write data in bytes'.
It is needed when you want to know not only read+write data bytes but
i.e. only write data in byte, or number of read requests, etc.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
[Updated property by MyungJoo. data_type --> event_type]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The patch changes the way how the 'ops' gets populated for different
device versions. The matching function now uses 'of_device_id' in order
to identify the device type.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Compile-testing the new driver on platforms without CONFIG_COMMON_CLK
leads to a link error:
drivers/devfreq/tegra20-devfreq.o: In function `tegra_devfreq_target':
tegra20-devfreq.c:(.text+0x288): undefined reference to `clk_set_min_rate'
Add a dependency on COMMON_CLK to avoid this.
Fixes: 1d39ee8dad6d ("PM / devfreq: Introduce driver for NVIDIA Tegra20")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Define new performance events supported by Exynos5422 SoC counters.
The counters are built-in in Dynamic Memory Controller and provide
information regarding memory utilization.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
A bit unexpectedly (but still documented), request_module may
return a positive value, in case of a modprobe error.
This is currently causing issues in the devfreq framework.
When a request_module exits with a positive value, we currently
return that via ERR_PTR. However, because the value is positive,
it's not a ERR_VALUE proper, and is therefore treated as a
valid struct devfreq_governor pointer, leading to a kernel oops.
Fix this by returning -EINVAL if request_module returns a positive
value.
Fixes: b53b012805 ("PM / devfreq: Fix static checker warning in try_then_request_governor")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Add devfreq driver for NVIDIA Tegra20 SoC's. The driver periodically
reads out Memory Controller counters and adjusts memory frequency based
on the memory clients activity.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[Removed MAINTAINERS updates by MyungJoo so that it can be sent elsewhere.]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
In order to reflect that driver serves NVIDIA Tegra30 and later SoC
generations, let's rename the driver's source file to "tegra30-devfreq.c".
This will make driver files to look more consistent after addition of a
driver for Tegra20.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The driver's compilation doesn't have any specific dependencies, hence
the COMPILE_TEST option can be supported in Kconfig.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The devfreq driver can be used on Tegra30 without any code change and
it works perfectly fine, the default Tegra124 parameters are good enough
for Tegra30.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
[Modified by MyungJoo to depends on Tegra30/114/124/210 only]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Move hardware configuration to governor's start/resume methods.
This allows to re-initialize hardware counters and reconfigure
cleanly if governor was stopped/paused. That is needed because we
are not aware of all hardware changes that happened while governor
was stopped and the paused state may get out of sync with reality,
hence it's better to start with a clean slate after the pause. In
a result there is no memory bandwidth starvation after resume from
suspend-to-ram that results in display controller underflowing that
happens on resume because of improper decision made by devfreq about
the required memory frequency. This change also cleans up code a tad
by moving hardware-configuration code into a single location.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no need to register the ACTMON's governor separately from
the driver, hence let's move the registration into the driver's probe
function for consistency and to make code cleaner a tad.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The ACTMON's governor supports only the Tegra's devfreq device and there
is no need to use any other governor, hence let's mark Tegra governor as
immutable to permanently stick it with Tegra's devfreq device.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The frequency value potentially could change in-between. It doesn't
cause any real problem at all right now, but that could change in the
future. Hence let's avoid the inconsistency.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reset hardware, disable ACTMON clock, release OPP's and handle all
possible error cases correctly, maintaining the correct tear down
order. Also use devm_platform_ioremap_resource() which is now available
in the kernel.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no guarantee that interrupt handling isn't running in parallel
with tegra_actmon_disable_interrupts(), hence it is necessary to protect
DEV_CTRL register accesses and clear IRQ status with ACTMON's IRQ being
disabled in the Interrupt Controller in order to ensure that device
interrupt is indeed being disabled.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no real need in the primary interrupt handler, hence move
everything to the secondary (threaded) handler. In a result locking
is consistent now and there are no potential races with the interrupt
handler because it is protected with the devfreq's mutex.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no real benefit from doing so, hence let's drop that rate setting
for consistency.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The clk_set_min_rate() could fail and in this case clk_set_rate() sets
rate to 0, which may drop EMC rate to minimum and make machine very
difficult to use.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The write memory barrier isn't needed because the BUS buffer is flushed
by read after write that happens after the removed wmb(), we will also
use readl() instead of the relaxed version to ensure that read is indeed
completed.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no need to insert memory barrier on each readl/writel
invocation, hence use the relaxed versions.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The kHz to Hz is incorrectly converted in a few places in the code,
this results in a wrong frequency being calculated because devfreq core
uses OPP frequencies that are given in Hz to clamp the rate, while
tegra-devfreq gives to the core value in kHz and then it also expects to
receive value in kHz from the core. In a result memory freq is always set
to a value which is close to ULONG_MAX because of the bug. Hence the EMC
frequency is always capped to the maximum and the driver doesn't do
anything useful. This patch was tested on Tegra30 and Tegra124 SoC's, EMC
frequency scaling works properly now.
Cc: <stable@vger.kernel.org> # 4.14+
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add basic tracing of the devfreq workqueue and delayed work.
It aims to capture changes of the polling intervals and device state.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
on-die termination (ODT) and auto power down parameters from kernel,
this patch adds the functionality to do this. Also, if DDR clock
frequency is lower than the on-die termination (ODT) disable frequency
this driver should disable the DDR ODT.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Some rk3399 GRF (Generic Register Files) definitions can be used for
different drivers. Move these definitions to a common include so we
don't need to duplicate these definitions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Force all Exynos buses to safe operation points before doing the system
reboot operation. There are board on which some aggressive power saving
operation points are behind the capabilities of the bootloader to properly
reset the hardware and boot the board. This way one can avoid board crash
early after reboot.
This fixes reboot issue on OdroidU3 board both with eMMC and SD boot.
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The patch 23c7b54ca1cd: "PM / devfreq: Fix devfreq_add_device() when
drivers are built as modules." leads to the following static checker
warning:
drivers/devfreq/devfreq.c:1043 governor_store()
warn: 'governor' can also be NULL
The reason is that the try_then_request_governor() function returns both
error pointers and NULL. It should just return error pointers, so fix
this by returning a ERR_PTR to the error intead of returning NULL.
Fixes: 23c7b54ca1 ("PM / devfreq: Fix devfreq_add_device() when drivers are built as modules.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
If the new governor fails to start, switch back to old governor so that the
devfreq state is not left in some weird limbo.
[Myungjoo: assume fatal on revert failure and set df->governor to NULL]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This variable is not used after initialization, so
remove it. And in order to unify the code style,
move the location where the dev_get_drvdata is called
by the way.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Marek Szyprowski