Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jens Thiele <karme@karme.de>
Cc: linux-input@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If using IRQF_TRIGGER_FALLING, then there is a race here: if the reset
completes before we enable the IRQ, then CHG is already low and touch
will be broken.
This has been seen on Chromebook Pixel 2.
A workaround is to reconfig T18 COMMSCONFIG to enable the RETRIGEN bit
using mxt-app:
mxt-app -W -T18 44
mxt-app --backup
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A wrong decoding of the touch coordinate message causes a wrong touch
ID. Touch ID for dual touch must be 0 or 1.
According to the actual Neonode nine byte touch coordinate coding,
the state is transported in the lower nibble and the touch ID in
the higher nibble of payload byte five.
Signed-off-by: Knut Wohlrab <Knut.Wohlrab@de.bosch.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In Cygnus SOC touch screen controller registers are shared with ADC and
flex timer. Using readl/writel could lead to race condition. So touch
screen driver is enhanced to support register access using syscon framework
API's to take care of mutually exclusive access.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of doing the dance with macro that either resolves to a pointer or
NULL, let's switch to using SIMPLE_DEV_PM_OPS().
Also let's mark suspend and resume methods as __maybe_unused instead of
guarding them with an #ifdef and rely on linker to drop unused code. Doing
so should allow better compile coverage.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
The BYD PS/2 protocol driver now uses absolute reporting mode and
should behave more like other touchpads; Synaptics driver needed to
extend one of its quirks to a newer firmware version, and a few USB
drivers got tightened up checks for the contents of their descriptors"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sur40 - fix DMA on stack
Input: ati_remote2 - fix crashes on detecting device with invalid descriptor
Input: synaptics - handle spurious release of trackstick buttons, again
Input: synaptics-rmi4 - remove check of Non-NULL array
Input: byd - enable absolute mode
Input: ims-pcu - sanity check against missing interfaces
Input: melfas_mip4 - add hw_version sysfs attribute
During the initialisation the driver uses a buffer on the stack for DMA.
That violates the cache coherency rules. The fix is to allocate the buffer
with kmalloc().
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Pull input updates from Dmitry Torokhov:
"The most notable item is addition of support for Synaptics RMI4
protocol which is native protocol for all current Synaptics devices
(touchscreens, touchpads). In later releases we'll switch devices
using HID and PS/2 protocol emulation to RMI4.
You will also get:
- BYD PS/2 touchpad protocol support for psmouse
- MELFAS MIP4 Touchscreen driver
- rotary encoder was moved away from legacy platform data and to
generic device properties API, devm_* API, and can now handle
encoders using more than 2 GPIOs
- Cypress touchpad driver was switched to devm_* API and device
properties
- other assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
ARM: pxa/raumfeld: use PROPERTY_ENTRY_INTEGER to define props
Input: synaptics-rmi4 - using logical instead of bitwise AND
Input: powermate - fix oops with malicious USB descriptors
Input: snvs_pwrkey - fix returned value check of syscon_regmap_lookup_by_phandle()
MAINTAINERS: add devicetree bindings to Input Drivers section
Input: synaptics-rmi4 - add device tree support to the SPI transport driver
Input: synaptics-rmi4 - add SPI transport driver
Input: synaptics-rmi4 - add support for F30
Input: synaptics-rmi4 - add support for F12
Input: synaptics-rmi4 - add device tree support for 2d sensors and F11
Input: synaptics-rmi4 - add support for 2D sensors and F11
Input: synaptics-rmi4 - add device tree support for RMI4 I2C devices
Input: synaptics-rmi4 - add I2C transport driver
Input: synaptics-rmi4 - add support for Synaptics RMI4 devices
Input: ad7879 - add device tree support
Input: ad7879 - fix default x/y axis assignment
Input: ad7879 - move header to platform_data directory
Input: ts4800 - add hardware dependency
Input: cyapa - fix for losing events during device power transitions
Input: sh_keysc - remove dependency on SUPERH
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW5j4RAAoJEHm+PkMAQRiGhVEH/0qZbM1J+WnCK92bm9+inCnB
JO2JViGIuCQB5BxljVMil2dzrw85D+dC7+fryr0wVBhhBlr0lXPJGSYCYYTEaI20
Wco5YlTmjRirUwmxWzBXvB5kvTdIaNfNYDcFch6lbsaLUNgqydNKtk08ckO/4k0D
AmaShW8swBiXE/RmHuj8H41ksHsnY8W62dlczEaAIfr4kluPX/kKnyXpmpvmZm1j
sM4fskPlq+Jz5pOXXFsFfrhiBgpSUnwSj1tNwK5+DkmaVnWOkPuwkqLBWqpy4pzm
GTeDBdf5/ixGxgNsZ2VWtbPnc2wEP7SIcu45MU7QFw5kqwDN2nN63BRVXI5Z5qY=
=RFx2
-----END PGP SIGNATURE-----
Merge tag 'v4.5' into next
Merge with Linux 4.5 to get PROPERTY_ENTRY_INTEGER() that is needed to
fix pxa/raumfeld rotary encoder properties.
Add device tree support for the I2C and SPI variant of AD7879(-1).
This allows to specify the touchscreen controller as a I2C client
node or SPI slave device. Most of the options available in platform
data are also available as device tree properties, the only exception
being GPIO capabilities, which can not be activated through device
tree currently.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The X/Y position measurements read from the controller are interpreted
wrong. The first measurement X+ contains the Y position, and the second
measurement Y+ the X position (see also Table 11 Register Table in the
data sheet).
The problem is already known and a swap option has been introduced:
commit 6680884a44 ("Input: ad7879 - add option to correct xy axis")
However, the meaning of the new boolean is inverted since the underlying
values are already swapped. Let ts->swap_xy set to true actually be the
swapped configuration of the two axis.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The header file is used by the SPI and I2C variant of the driver.
Therefore, move it to a more generic place under platform_data.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Technologic Systems TS-4800 is an i.MX515 board, so its drivers
are useless unless building a SOC_IMX51 kernel, except for build
testing purposes.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bring in updates to roraty encoder driver switching it away from legacy
platform data and over to generic device properties and adding support
for encoders using more than 2 GPIOs.
Add support for retrieving device resolution (pixels per mm) from firmware
and using it when setting up input device.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit e4b88e1989
"Input: stmpe-ts - enforce device tree only mode"
removed platform data but accidentally stripped away useful
kerneldoc, so reintroduce it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is an input driver for MELFAS MIP4 Touchscreen devices, such as
MMS400, MMS500, MCS8000, MIT200, MIT300, MIT400, MFS10. All devices
implementing MIP4 protocol (MELFAS Interface Protocol Version 4) should
be supported by this driver.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix spelling typos found in printk and Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a driver for the imx25 ADC/TSC module. It controls the
touchscreen conversion queue and creates a touchscreen input device.
The driver currently only supports 4 wire touchscreens. The driver uses
a simple conversion queue of precharge, touch detection, X measurement,
Y measurement, precharge and another touch detection.
This driver uses the regmap from the parent to setup some touch specific
settings in the core driver and setup a idle configuration with touch
detection.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
[fix clock's period calculation]
[fix calculation of the 'settling' value]
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
drivers/input/touchscreen/colibri-vf50-ts.c: In function ‘vf50_ts_probe’:
drivers/input/touchscreen/colibri-vf50-ts.c:302: error: implicit declaration of function ‘of_property_read_u32’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A recent patch broke parsing the gain, offset, and threshold parameters
from device tree. Instead of setting the cached values and writing them
to the correct registers during probe, it would write the values from DT
into the register address variables and never write them to the chip
during normal operation.
Fixes: 2e23b7a963 ("Input: edt-ft5x06 - use generic properties API")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
If COMPILE_TEST is enabled, relax the dependency on GPIOLIB for the
recently introduced or relaxed symbols TOUCHSCREEN_GOODIX and
TOUCHSCREEN_COLIBRI_VF50.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since we removed support for calling an init() callback from
the platform data, introduce a function which initializes
the chip by performing a hard reset, using the reset gpio
defined in the device properties.
Signed-off-by: Oreste Salerno <oreste.salerno@tomtom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Drop support for platform data passed via a C-structure and switch to
device properties instead, which should make the driver compatible
with all platforms: OF, ACPI and static boards. Static boards should
use property sets to communicate device parameters to the driver.
Signed-off-by: Oreste Salerno <oreste.salerno@tomtom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
"The second round of updates for the input subsystem, mainly changes to
xpad driver to better hanlde Xbox One controllers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio-keys - allow disabling individual buttons in DT
Input: gpio-keys - allow setting input device name in DT
Input: xpad - correct xbox one pad device name
Input: atmel_mxt_ts - improve touchscreen size/orientation handling
Input: xpad - use LED API when identifying wireless controllers
Input: xpad - workaround dead irq_out after suspend/ resume
Input: xpad - update Xbox One Force Feedback Support
Input: xpad - correctly handle concurrent LED and FF requests
Input: xpad - handle "present" and "gone" correctly
Input: xpad - remove spurious events of wireless xpad 360 controller
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull input updates from Dmitry Torokhov:
- new driver for eGalaxTouch serial touchscreen
- new driver for TS-4800 touchscreen
- an update for Goodix touchscreen driver
- PS/2 mouse module was reworked to limit number of protocols we try on
pass-through ports to speed up their detection time
- wacom_w8001 touchscreen driver now reports pen and touch via separate
instances of input devices
- other driver changes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (42 commits)
Input: elantech - mark protocols v2 and v3 as semi-mt
Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE
Input: gpio-keys - fix check for disabling unsupported keys
Input: omap-keypad - remove dead check
Input: ti_am335x_tsc - fix HWPEN interrupt handling
Input: omap-keypad - set tasklet data earlier
Input: rohm_bu21023 - fix handling of retrying firmware update
Input: ALPS - report v3 pinnacle trackstick device only if is present
Input: ALPS - detect trackstick presence for v7 protocol
Input: pcap_ts - use to_delayed_work
Input: bma150 - constify bma150_cfg structure
Input: i8042 - add Fujitsu Lifebook U745 to the nomux list
Input: egalax_ts_serial - fix potential NULL dereference on error
Input: uinput - sanity check on ff_effects_max and EV_FF
Input: uinput - rework ABS validation
Input: uinput - add new UINPUT_DEV_SETUP and UI_ABS_SETUP ioctl
Input: goodix - use "inverted_[xy]" flags instead of "rotated_screen"
Input: goodix - add axis swapping and axis inversion support
Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
Input: goodix - add power management support
...
Both T100 and T9 handle range and orientation in a similar fashion.
Reduce duplication between the two implementations.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
As of e0361b7017 ("Input: wacom_w8001 - split the touch and pen devices
into two devices") the touch events aren't multiplexed over the same device
anymore, the use of ABS_MT_TOOL_TYPE is superfluous. And even before then
it only ever sent MT_TOOL_TYPE_FINGER anyway.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove write to REG_IRQCLR and REG_IRQWAKEUP in interrupt handler for
IRQENB_HW_PEN as the resume handler should and does clear REG_IRQWAKEUP.
IRQENB_HW_PEN bit is set in irqclr so that all interrupts get cleared
later so let IRQENB_HW_PEN be cleared by that.
Without this patch wakeup events from TSC_ADC do not work because pending
interrupts in TSC_ADC were causing HW_PEN interrupt, needed for wake from
suspend modes, to get disabled immediately by IRQ handler after being
enabled and preventing wake from happening.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Because of the wrong condition we'd never retry firmware update.
Acked-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
