Make intel_pstate update per-logical-CPU limits when the global
settings are changed to ensure that they are always in sync and
users will not see confusing values in per-logical-CPU sysfs
attributes.
This also fixes the problem that setting the "no_turbo" global
attribute to 1 in the "passive" mode (ie. when intel_pstate acts
as a regular cpufreq driver) when scaling_governor is set to
"performance" has no effect.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Race conditions are possible if intel_cpufreq_verify_policy()
is executed in parallel with global limits updates from sysfs,
so the invocation of intel_pstate_update_perf_limits() in it
should be carried out under intel_pstate_limits_lock.
Make that happen.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Theoretically, intel_pstate_resume() may be executed in parallel
with intel_pstate_set_policy(), if the latter is invoked via
cpufreq_update_policy() as a result of a notification, so use
intel_pstate_limits_lock in there too to avoid race conditions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
If intel_pstate works in the passive mode in which it acts as
a regular cpufreq driver and collaborates with generic cpufreq
governors, the PID parameters are not used, so do not expose
them via debugfs in that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible to provide hints to the HWP algorithms in the processor
to be more performance centric to more energy centric. These hints are
provided by using HWP energy performance preference (EPP) or energy
performance bias (EPB) settings.
The scope of these settings is per logical processor, which means that
each of the logical processors in the package can be programmed with a
different value.
This change provides cpufreq sysfs interface to provide hint. For each
policy, two additional attributes will be available to check and provide
hint. These attributes will only be present when the intel_pstate driver
is using HWP mode.
These attributes are:
- energy_performance_available_preferences
- energy_performance_preference
To get list of supported hints:
$ cat energy_performance_available_preferences
default performance balance_performance balance_power power
The current preference can be read or changed via cpufreq sysfs
attribute "energy_performance_preference". Reading from this attribute
will display current effective setting changed via any method. User can
write any of the valid preference string to this attribute. User can
always restore to power-on default by writing "default".
Implementation
Since these hints can be provided by direct MSR write or using some tools
like x86_energy_perf_policy, the driver internally doesn't maintain any
state. The user operation will result in direct read/write of MSR: 0x774
(HWP_REQUEST_MSR). Also driver use read modify write to update other
fields in this MSR.
Summary of changes:
- struct cpudata field epp_saved is renamed to epp_powersave, as this
stores the value to restore once policy is switched from performance
to powersave to restore original powersave EPP value.
- A new struct cpudata field epp_saved is used to store the raw MSR
EPP/EPB value when a CPU goes offline or on suspend and restore on
online/resume. This ensures that EPP value is restored to correct
value irrespective of the means used to set.
- EPP/EPB value ranges are fixed for each preference, which can be
set for the cpufreq sysfs, so user request is mapped to/from this
range.
- New attributes are only added when HWP is present.
- Since EPP value of 0 is valid the fields are initialized to
-EINVAL when not valid. The field epp_default is read only once
after powerup to avoid reading on subsequent CPU online operation
- New suspend callback to store epp on suspend operation
- Don't invalidate old epp_saved field on resume and online as now
we can restore last epp value on suspend and this field can still
have old EPP value sampled during switch to performance from
powersave.
- While here optimized setting of cpu_data->epp_powersave = epp in
intel_pstate_hwp_set() as this was done in both true and false
paths.
- epp/epb set function returns error to caller on failure to pass
on to user space for display.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To avoid race conditions from multiple threads, increase the scope
of intel_pstate_limits_lock to include HWP requests also.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Knights Mill (KNM) to the list of CPUIDs supported by intel_pstate.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The addition of the generic governor support marked the
intel_pstate_exit_perf_limits as inline(), which fixed a warning,
but it introduced another warning:
drivers/cpufreq/intel_pstate.c: In function ‘intel_pstate_exit_perf_limits’:
drivers/cpufreq/intel_pstate.c:483:1: error: no return statement in function returning non-void [-Werror=return-type]
This changes it back to a 'void' return type, and changes the
corresponding intel_pstate_init_acpi_perf_limits() function to
be inline as well for consistency.
Fixes: 001c76f05b (cpufreq: intel_pstate: Generic governors support)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When user has selected performance policy, then set the EPP (Energy
Performance Preference) or EPB (Energy Performance Bias) to maximum
performance mode.
Also when user switch back to powersave, then restore EPP/EPB to last
EPP/EPB value before entering performance mode. If user has not changed
EPP/EPB manually then it will be power on default value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Even with round up of limits->min_perf and limits->max_perf, in some
cases resultant performance is 100 MHz less than the desired.
For example when the maximum frequency is 3.50 GHz, setting
scaling_min_frequency to 2.3 GHz always results in 2.2 GHz minimum.
Currently the fixed floating point operation uses 8 bit precision for
calculating limits->min_perf and limits->max_perf. For some operations
in this driver the 14 bit precision is used. Using the 14 bit precision
also for calculating limits->min_perf and limits->max_perf, addresses
this issue.
Introduced fp_ext_toint() equivalent to fp_toint() and int_ext_tofp()
equivalent to int_tofp() with 14 bit precision.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In some use cases, user wants to enforce a minimum performance limit on
CPUs. But because of simple division the resultant performance is 100 MHz
less than the desired in some cases.
For example when the maximum frequency is 3.50 GHz, setting
scaling_min_frequency to 1.6 GHz always results in 1.5 GHz minimum. With
simple round up, the frequency can be set to 1.6 GHz to minimum in this
case. This round up is already done to max_policy_pct and max_perf, so do
the same for min_policy_pct and min_perf.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There may be reasons to use generic cpufreq governors (eg. schedutil)
on Intel platforms instead of the intel_pstate driver's internal
governor. However, that currently can only be done by disabling
intel_pstate altogether and using the acpi-cpufreq driver instead
of it, which is subject to limitations.
First of all, acpi-cpufreq only works on systems where the _PSS
object is present in the ACPI tables for all logical CPUs. Second,
on those systems acpi-cpufreq will only use frequencies listed by
_PSS which may be suboptimal. In particular, by convention, the
whole turbo range is represented in _PSS as a single P-state and
the frequency assigned to it is greater by 1 MHz than the greatest
non-turbo frequency listed by _PSS. That may confuse governors to
use turbo frequencies less frequently which may lead to suboptimal
performance.
For this reason, make it possible to use the intel_pstate driver
with generic cpufreq governors as a "normal" cpufreq driver. That
mode is enforced by adding intel_pstate=passive to the kernel
command line and cannot be disabled at run time. In that mode,
intel_pstate provides a cpufreq driver interface including
the ->target() and ->fast_switch() callbacks and is listed in
scaling_driver as "intel_cpufreq".
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Currently, intel_pstate is unable to control P-states on my
IvyBridge-based Acer Aspire S5, because they are controlled by SMM
on that machine by default and it is necessary to request OS control
of P-states from it via the SMI Command register exposed in the ACPI
FADT. intel_pstate doesn't do that now, but acpi-cpufreq and other
cpufreq drivers for x86 platforms do.
Address this problem by making intel_pstate use the ACPI-defined
mechanism as well. However, intel_pstate is not modular and it
doesn't need the module refcount tricks played by
acpi_processor_notify_smm(), so export the core of this function
to it as acpi_processor_pstate_control() and make it call that.
[The changes in processor_perflib.c related to this should not
make any functional difference for the acpi_processor_notify_smm()
users].
To be safe, only call acpi_processor_notify_smm() from intel_pstate
if ACPI _PPC support is enabled in it.
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Use get_target_pstate_use_cpu_load() to calculate target P-State for
devices, with the preferred power management profile in ACPI FADT
set to PM_MOBILE.
This may help in resolving some thermal issues caused by low sustained
cpu bound workloads. The current algorithm tend to over provision in this
case as it doesn't look at the CPU busyness.
Also included the fix from Arnd Bergmann <arnd@arndb.de> to solve compile
issue, when CONFIG_ACPI is not defined.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The limits variable gets modified from intel_pstate sysfs and also gets
modified from cpufreq sysfs. So protect with a mutex to keep data
integrity, when they are getting modified from multiple threads.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When policy->max and policy->min are same, in some cases they don't
result in the same frequency cap. The max_policy_pct is rounded up but
not min_perf_pct. So even when they are same, results in different
percentage or maximum and minimum.
Since minimum is a conservative value for power, a lower value without
rounding is better in most of the cases, unless user wants
policy->max = policy->min.
This change uses use the same policy percentage when policy->max and
policy->min are same.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Intel P-State offers two interface to set performance limits:
- Intel P-State sysfs
/sys/devices/system/cpu/intel_pstate/max_perf_pct
/sys/devices/system/cpu/intel_pstate/min_perf_pct
- cpufreq
/sys/devices/system/cpu/cpu*/cpufreq/scaling_max_freq
/sys/devices/system/cpu/cpu*/cpufreq/scaling_min_freq
In the current implementation both of the above methods, change limits
to every CPU in the system. Moreover the limits placed using cpufreq
policy interface also presented in the Intel P-State sysfs via modified
max_perf_pct and min_per_pct during sysfs reads. This allows to check
percent of reduced/increased performance, irrespective of method used to
limit.
There are some new generations of processors, where it is possible to
have limits placed on individual CPU cores. Using cpufreq interface it
is possible to set limits on each CPU. But the current processing will
use last limits placed on all CPUs. So the per core limit feature of
CPUs can't be used.
This change brings in capability to set P-States limits for each CPU,
with some limitations. In this case what should be the read of
max_perf_pct and min_perf_pct? It can be most restrictive limits placed
on any CPU or max possible performance on any given CPU on which no
limits are placed. In either case someone will have issue.
So the consensus is, we can't have both sysfs controls present when user
wants to use limit per core limits.
- By default per-core-control feature is not enabled. So no one will
notice any difference.
- The way to enable is by kernel command line
intel_pstate=per_cpu_perf_limits
- When the per-core-controls are enabled there is no display of for both
read and write on
/sys/devices/system/cpu/intel_pstate/max_perf_pct
/sys/devices/system/cpu/intel_pstate/min_perf_pct
- User can change limits using
/sys/devices/system/cpu/cpu*/cpufreq/scaling_max_freq
/sys/devices/system/cpu/cpu*/cpufreq/scaling_min_freq
/sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
- User can still observe turbo percent and number of P-States from
/sys/devices/system/cpu/intel_pstate/turbo_pct
/sys/devices/system/cpu/intel_pstate/num_pstates
- User can read write system wide turbo status
/sys/devices/system/cpu/no_turbo
While changing this BUG_ON is changed to WARN_ON, as they are not fatal
errors for the system.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The only times at which intel_pstate checks the policy set for
a given CPU is the initialization of that CPU and updates of its
policy settings from cpufreq when intel_pstate_set_policy() is
invoked.
That is insufficient, however, because intel_pstate uses the same
P-state selection function for all CPUs regardless of the policy
setting for each of them and the P-state limits are shared between
them. Thus if the policy is set to "performance" for a particular
CPU, it may not behave as expected if the cpufreq settings are
changed subsequently for another CPU.
That can be easily demonstrated by writing "performance" to
scaling_governor for all CPUs and then switching it to "powersave"
for one of them in which case all of the CPUs will behave as though
their scaling_governor were all "powersave" (even though the policy
still appears to be "performance" for the remaining CPUs).
Fix this problem by modifying intel_pstate_adjust_busy_pstate() to
always set the P-state to the maximum allowed by the current limits
for all CPUs whose policy is set to "performance".
Note that it still is recommended to always change the policy setting
in the same way for all CPUs even with this fix applied to avoid
confusion.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit a4675fbc4a (cpufreq: intel_pstate: Replace timers with
utilization update callbacks) the cpufreq governor callbacks may not
be invoked on NOHZ_FULL CPUs and, in particular, switching to the
"performance" policy via sysfs may not have any effect on them. That
is a problem, because it usually is desirable to squeeze the last
bit of performance out of those CPUs, so work around it by setting
the maximum P-state (within the limits) in intel_pstate_set_policy()
upfront when the policy is CPUFREQ_POLICY_PERFORMANCE.
Fixes: a4675fbc4a (cpufreq: intel_pstate: Replace timers with utilization update callbacks)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
When target state is calculated using get_target_pstate_use_cpu_load(),
PID controller is not used, hence it has no effect on performance.
So don't present debugfs entries to tune PID controller.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "IOwait boosting" mechanism is only used by the
get_target_pstate_use_cpu_load() governor function and the
boost_iowait flag in pid_params is always set when that function
is in use (and it is never set otherwise). This means that the
boost_iowait flag is in fact redundant and may be dropped.
For this reason, replace the boost_iowait flag check in
intel_pstate_update_util() with an equivalent check against
pstate_funcs.get_target_pstate and drop that flag.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
It looks like the name of struct pstate_adjust_policy was updated
without updating its kerneldoc comment accordingly, so fix that
mistake.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PID algorithm used by the intel_pstate driver tends to drive
performance to the minimum for workloads with utilization below the
setpoint, which is undesirable, so replace it with a modified
"proportional" algorithm on Atom.
The new algorithm will set the new P-state to be 1.25 times the
available maximum times the (frequency-invariant) utilization during
the previous sampling period except when the target P-state computed
this way is lower than the average P-state during the previous
sampling period. In the latter case, it will increase the target by
50% of the difference between it and the average P-state to prevent
performance from dropping down too fast in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Make the comment explaining the meaning of the perf_scaled variable
in get_target_pstate_use_performance() more straightforward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a requirement that MSR MSR_PM_ENABLE must be set to 0x01 before
reading MSR_HWP_CAPABILITIES on a given CPU. If cpufreq init() is
scheduled on a CPU which is not same as policy->cpu or migrates to a
different CPU before calling msr read for MSR_HWP_CAPABILITIES, it
is possible that MSR_PM_ENABLE was not to set to 0x01 on that CPU.
This will cause GP fault. So like other places in this path
rdmsrl_on_cpu should be used instead of rdmsrl.
Moreover the scope of MSR_HWP_CAPABILITIES is on per thread basis, so it
should be read from the same CPU, for which MSR MSR_HWP_REQUEST is
getting set.
dmesg dump or warning:
[ 22.014488] WARNING: CPU: 139 PID: 1 at arch/x86/mm/extable.c:50 ex_handler_rdmsr_unsafe+0x68/0x70
[ 22.014492] unchecked MSR access error: RDMSR from 0x771
[ 22.014493] Modules linked in:
[ 22.014507] CPU: 139 PID: 1 Comm: swapper/0 Not tainted 4.7.5+ #1
...
...
[ 22.014516] Call Trace:
[ 22.014542] [<ffffffff813d7dd1>] dump_stack+0x63/0x82
[ 22.014558] [<ffffffff8107bc8b>] __warn+0xcb/0xf0
[ 22.014561] [<ffffffff8107bcff>] warn_slowpath_fmt+0x4f/0x60
[ 22.014563] [<ffffffff810676f8>] ex_handler_rdmsr_unsafe+0x68/0x70
[ 22.014564] [<ffffffff810677d9>] fixup_exception+0x39/0x50
[ 22.014604] [<ffffffff8102e400>] do_general_protection+0x80/0x150
[ 22.014610] [<ffffffff817f9ec8>] general_protection+0x28/0x30
[ 22.014635] [<ffffffff81687940>] ? get_target_pstate_use_performance+0xb0/0xb0
[ 22.014642] [<ffffffff810600c7>] ? native_read_msr+0x7/0x40
[ 22.014657] [<ffffffff81688123>] intel_pstate_hwp_set+0x23/0x130
[ 22.014660] [<ffffffff81688406>] intel_pstate_set_policy+0x1b6/0x340
[ 22.014662] [<ffffffff816829bb>] cpufreq_set_policy+0xeb/0x2c0
[ 22.014664] [<ffffffff81682f39>] cpufreq_init_policy+0x79/0xe0
[ 22.014666] [<ffffffff81682cb0>] ? cpufreq_update_policy+0x120/0x120
[ 22.014669] [<ffffffff816833a6>] cpufreq_online+0x406/0x820
[ 22.014671] [<ffffffff8168381f>] cpufreq_add_dev+0x5f/0x90
[ 22.014717] [<ffffffff81530ac8>] subsys_interface_register+0xb8/0x100
[ 22.014719] [<ffffffff816821bc>] cpufreq_register_driver+0x14c/0x210
[ 22.014749] [<ffffffff81fe1d90>] intel_pstate_init+0x39d/0x4d5
[ 22.014751] [<ffffffff81fe13f2>] ? cpufreq_gov_dbs_init+0x12/0x12
Cc: 4.3+ <stable@vger.kernel.org> # 4.3+
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add io_boost percent to current pstate_sample tracepoint.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify the P-state selection algorithm for Atom processors to use
the new SCHED_CPUFREQ_IOWAIT flag instead of the questionable
get_cpu_iowait_time_us() function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is useful to know the reason why cpufreq_update_util() has just
been called and that can be passed as flags to cpufreq_update_util()
and to the ->func() callback in struct update_util_data. However,
doing that in addition to passing the util and max arguments they
already take would be clumsy, so avoid it.
Instead, use the observation that the schedutil governor is part
of the scheduler proper, so it can access scheduler data directly.
This allows the util and max arguments of cpufreq_update_util()
and the ->func() callback in struct update_util_data to be replaced
with a flags one, but schedutil has to be modified to follow.
Thus make the schedutil governor obtain the CFS utilization
information from the scheduler and use the "RT" and "DL" flags
instead of the special utilization value of ULONG_MAX to track
updates from the RT and DL sched classes. Make it non-modular
too to avoid having to export scheduler variables to modules at
large.
Next, update all of the other users of cpufreq_update_util()
and the ->func() callback in struct update_util_data accordingly.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
* pm-sleep:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
* pm-cpufreq:
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
* pm-core:
PM-wakeup: Delete unnecessary checks before three function calls
* pm-opp:
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
Add Skylake-X and Broadwell-X IDs for out-of-band (OBB) control of
P-States.
For these processors, if MSR_MISC_PWR_MGMT BIT(8) == 1, then the
Intel P-State driver should exit as OS can't control P-States.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Subject/changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The MSR MSR_HWP_INTERRUPT is valid only when CPUID.06H:EAX[8] = 1, so
check for feature before accessing this MSR.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, intel_pstate only updates the cpu_frequency tracepoint
if the new P-state to set is different from the current one, but
that causes powertop to report 100% idle on an 100% loaded system
sometimes.
Prevent that from happening by updating the cpu_frequency tracepoint
every time intel_pstate_update_pstate() is called.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>-
When I was working with the Intel P state driver I came across a
remnant struct element that is no longer needed after the function
intel_pstate_calc_freq() was retired.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If MSR_CONFIG_TDP_CONTROL is locked, we currently try to address some
MSR 0x80000648 or so. Mask out the relevant level bits 0 and 1.
Found while running over the Jailhouse hypervisor which became upset
about this strange MSR index.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace MSR_NHM_TURBO_RATIO_LIMIT with MSR_TURBO_RATIO_LIMIT.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pid_params is written once by copy_pid_params() during initialization,
and thereafter is mostly read by hot path intel_pstate_update_util().
The read of pid_params gets more after commit a4675fbc4a ("cpufreq:
intel_pstate: Replace timers with utilization update callbacks")
pstate_funcs is written once by copy_cpu_funcs() during initialization,
and thereafter is mostly read by hot path intel_pstate_update_util()
hwp_active is written to once during initialization and thereafter is
mostly read by hot path intel_pstate_update_util().
The fact that they are mostly read and not written to makes them
candidates for __read_mostly declarations.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These functions/variables are not needed after booting, so mark them
as __init or __initdata.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__initdata should be placed between the variable name and equal sign
(if there is) for the variable to be placed in the intended section.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
intel_pstate_set_policy() is invoked by the cpufreq core during
driver initialization, on changes of policy attributes (minimim and
maximum frequency, for example) via sysfs and via CPU notifications
from the platform firmware. On some platforms the latter may occur
relatively often.
Commit bb6ab52f2b (intel_pstate: Do not set utilization update hook
too early) made intel_pstate_set_policy() clear the CPU's utilization
update hook before updating the policy attributes for it (and set the
hook again after doind that), but that involves invoking
synchronize_sched() and adds overhead to the CPU notifications
mentioned above and to the sched-RCU handling in general.
That extra overhead is arguably not necessary, because updating
policy attributes when the CPU's utilization update hook is active
should not lead to any adverse effects, so drop the clearing of
the hook from intel_pstate_set_policy() and make it check if
the hook has been set already when attempting to set it.
Fixes: bb6ab52f2b (intel_pstate: Do not set utilization update hook too early)
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The maximum turbo P-State used by the intel_pstate driver may be
limited by ACPI _PSS table entry 0. After commit 9522a2ff9c
(cpufreq: intel_pstate: Enforce _PPC limits), the maximum performance
on servers will be capped by the _PSS table entry 0 by default.
Even though that is formally correct, it may lead to preformance
regressions in some cases. Namely, if the _PSS table entry 0 is
not the maximum turbo P-State, performance measured after commit
9522a2ff9c will not match the performance measured before that
commit on the same system.
For this reason, modify the code to always use the maximum turbo
frequency as the one that corresponds to _PSS table entry 0 if turbo
is enabled in the BIOS. This way, the performance levels from
before commit 9522a2ff9c will be restored on the affected systems.
Fixes: 9522a2ff9c (cpufreq: intel_pstate: Enforce _PPC limits)
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Broxton CPU model number.
Broxton requires core_params to get performance limits via MSRs, but
it is an Atom platform, which requires more power optimized algorithm.
So the P state selection will use similar algorithm as other Atom
platforms.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When turbo is disabled, the ->set_policy() interface is broken.
For example, when turbo is disabled and cpuinfo.max = 2900000 (full
max turbo frequency), setting the limits results in frequency less
than the requested one:
Set 1000000 KHz results in 0700000 KHz
Set 1500000 KHz results in 1100000 KHz
Set 2000000 KHz results in 1500000 KHz
This is because the limits->max_perf fraction is calculated using
the max turbo frequency as the reference, but when the max P-State is
capped in intel_pstate_get_min_max(), the reference is not the max
turbo P-State. This results in reducing max P-State.
One option is to always use max turbo as reference for calculating
limits. But this will not be correct. By definition the intel_pstate
sysfs limits, shows percentage of available performance. So when
BIOS has disabled turbo, the available performance is max non turbo.
So the max_perf_pct should still show 100%.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Subject & changelog, rewrite in fewer lines of code ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>