The transport offset of the IPv4 packet should be fixed and wouldn't
be out of the hw limitation, so the r8152_csum_workaround() should
be used for IPv6 packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get offloads to work with Generic Routing Encapsulation (GRE), the
outer transport header has to be reset after skb_push is done. This
patch has the support for this fix and hence GRE offloading.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several issues in fst_add_one() and fst_init_card():
- invalid pointer dereference at card->ports[card->nports - 1] if
register_hdlc_device() fails for the first port in fst_init_card();
- fst_card_array overflow at fst_card_array[no_of_cards_added]
because there is no checks for array overflow;
- use after free because pointer to deallocated card is left in fst_card_array
if something fails after fst_card_array[no_of_cards_added] = card;
- several leaks on failure paths in fst_add_one().
The patch fixes all the issues and makes code more readable.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When event spec is shared by multiple channels, which has definition
for mask_shared_by_type, iio_device_register_eventset fails.
For example:
static const struct iio_event_spec iio_dummy_events[] = {
{
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_RISING,
.mask_separate = BIT(IIO_EV_INFO_ENABLE),
.mask_shared_by_type = BIT(IIO_EV_INFO_VALUE),
}, {
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_FALLING,
.mask_separate = BIT(IIO_EV_INFO_ENABLE),a
.mask_shared_by_type = BIT(IIO_EV_INFO_VALUE),
}
};
If two channels use this event spec, this will result in error.
This change handles EBUSY error similar to iio_device_add_info_mask_type().
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
Commit 007649375f ("ext4: initialize multi-block allocator before
checking block descriptors") causes the block group descriptor's count
of the number of free blocks to become inconsistent with the number of
free blocks in the allocation bitmap. This is a harmless form of fs
corruption, but it causes the kernel to potentially remount the file
system read-only, or to panic, depending on the file systems's error
behavior.
Thanks to Eric Whitney for his tireless work to reproduce and to find
the guilty commit.
Fixes: 007649375f ("ext4: initialize multi-block allocator before checking block descriptors"
Cc: stable@vger.kernel.org # 3.15
Reported-by: David Jander <david@protonic.nl>
Reported-by: Matteo Croce <technoboy85@gmail.com>
Tested-by: Eric Whitney <enwlinux@gmail.com>
Suggested-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
multipath_busy. This impacted cable-pull testing and also the ability
to boot with IPR SCSI on a POWER8 box.
. Fix possible deadlock with deferred device removal by using a new
dedicated workqueue rather than using the system workqueue.
. Fix NULL pointer crash due to race condition in dm-io's wake up code
for sync_io by using a completion.
. Update dm-crypt and dm-zero author name following legal name change;
this is important to Jana so I didn't see any reason to hold it back.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTv+hvAAoJEMUj8QotnQNawwMH/2yQ7AE3dh44jGr1fp0UEP8e
Vd7HWtUJAm4+lYkPH7AjLCw3YBwWh/ajLXAwMpPBI878o5sgoWTfnq0hbecqoWkt
5EugETiZ20C3K/llNFpw9xdtlObFwI21WUGqmu8ygYvfSvdbg6THPT5o8BdtEvnb
MDBrrrpBpUwMCGw3v7jIoYrKZbWmp46iy5KwVqBbXnD3shpOU8KpasyIOrqlrqjJ
z7BzfprN6ut1zaVs83N4iPMPnSPrIloUisGpPn1r74qRYUv/AXQgiv09WPA3keTN
erRGFU9Mr0I4MGOLTuqHyCVO0t4tze1pL8jwEk29GUkXXcr9Is4p9I307Cm7WvE=
=pBlO
-----END PGP SIGNATURE-----
Merge tag 'dm-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM multipath IO hang regression from 3.15 due to logic bug in
multipath_busy. This impacted cable-pull testing and also the
ability to boot with IPR SCSI on a POWER8 box.
- Fix possible deadlock with deferred device removal by using a new
dedicated workqueue rather than using the system workqueue.
- Fix NULL pointer crash due to race condition in dm-io's wake up code
for sync_io by using a completion.
- Update dm-crypt and dm-zero author name following legal name change;
this is important to Jana so I didn't see any reason to hold it back.
* tag 'dm-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: fix IO hang due to logic bug in multipath_busy
dm io: fix a race condition in the wake up code for sync_io
dm crypt, dm zero: update author name following legal name change
dm: allocate a special workqueue for deferred device removal
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few more powerpc fixes for 3.16
There's a small series of 3 patches that fix saving/restoring MMUCR2
when using KVM without which perf goes completely bonkers in the host
system. Another perf fix from Anton that's been rotting away in
patchwork due to my poor eyesight, a couple of compile fixes, a little
addition to the WSP removal by Michael (removing a bit more dead
stuff) and a fix for an embarassing regression with our soft irq
masking"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: Never program book3s PMCs with values >= 0x80000000
powerpc: Disable RELOCATABLE for COMPILE_TEST with PPC64
powerpc/perf: Clear MMCR2 when enabling PMU
powerpc/perf: Add PPMU_ARCH_207S define
powerpc/kvm: Remove redundant save of SIER AND MMCR2
powerpc/powernv: Check for IRQHAPPENED before sleeping
powerpc: Clean up MMU_FTRS_A2 and MMU_FTR_TYPE_3E
powerpc/cell: Fix compilation with CONFIG_COREDUMP=n
We are seeing a lot of PMU warnings on POWER8:
Can't find PMC that caused IRQ
Looking closer, the active PMC is 0 at this point and we took a PMU
exception on the transition from negative to 0. Some versions of POWER8
have an issue where they edge detect and not level detect PMC overflows.
A number of places program the PMC with (0x80000000 - period_left),
where period_left can be negative. We can either fix all of these or
just ensure that period_left is always >= 1.
This patch takes the second option.
Cc: <stable@vger.kernel.org>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull drm fixes from Dave Airlie:
"Nothing too scary, we have one outstanding i915 regression but Daniel
has promised the fix as soon as he's finished testing it a bit.
Fixes for the main x86 drivers:
- radeon: dpm fixes, displayport regression fix
- i915: quirks for backlight regression, edp reboot fix, valleyview
black screen fixes
- nouveau: display port regression fixes, fix for memory reclocking"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: Reenabling SS on Cayman
drm/radeon: fix typo in ci_stop_dpm()
drm/radeon: fix typo in golden register setup on evergreen
drm/radeon: only print meaningful VM faults
drm/radeon/dp: return -EIO for flags not zero case
drm/i915/vlv: T12 eDP panel timing enforcement during reboot
drm/i915: Only unbind vgacon, not other console drivers
drm/i915: Don't clobber the GTT when it's within stolen memory
drm/i915/vlv: Update the DSI ULPS entry/exit sequence
drm/i915/vlv: DPI FIFO empty check is not needed
drm/i915: Toshiba CB35 has a controllable backlight
drm/i915: Acer C720 and C720P have controllable backlights
drm/i915: quirk asserts controllable backlight presence, overriding VBT
drm/nouveau/ram: fix test for gpio presence
drm/nouveau/dp: workaround broken display
drm/nouveau/dp: fix required link bandwidth calculations
drm/nouveau/kms: restore fbcon after display has been resumed
drm/nv50-/kms: pass a non-zero value for head to sor dpms methods
drm/nouveau/fb: Prevent inlining of ramfuc_reg
drm/gk104/ram: bash mpll bit 31 on
powerpc:allmodconfig has been failing for some time with the following
error.
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:1312: Error: attempt to move .org backwards
make[1]: *** [arch/powerpc/kernel/head_64.o] Error 1
A number of attempts to fix the problem by moving around code have been
unsuccessful and resulted in failed builds for some configurations and
the discovery of toolchain bugs.
Fix the problem by disabling RELOCATABLE for COMPILE_TEST builds instead.
While this is less than perfect, it avoids substantial code changes
which would otherwise be necessary just to make COMPILE_TEST builds
happy and might have undesired side effects.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On POWER8 when switching to a KVM guest we set bits in MMCR2 to freeze
the PMU counters. Aside from on boot they are then never reset,
resulting in stuck perf counters for any user in the guest or host.
We now set MMCR2 to 0 whenever enabling the PMU, which provides a sane
state for perf to use the PMU counters under either the guest or the
host.
This was manifesting as a bug with ppc64_cpu --frequency:
$ sudo ppc64_cpu --frequency
WARNING: couldn't run on cpu 0
WARNING: couldn't run on cpu 8
...
WARNING: couldn't run on cpu 144
WARNING: couldn't run on cpu 152
min: 18446744073.710 GHz (cpu -1)
max: 0.000 GHz (cpu -1)
avg: 0.000 GHz
The command uses a perf counter to measure CPU cycles over a fixed
amount of time, in order to approximate the frequency of the machine.
The counters were returning zero once a guest was started, regardless of
weather it was still running or had been shut down.
By dumping the value of MMCR2, it was observed that once a guest is
running MMCR2 is set to 1s - which stops counters from running:
$ sudo sh -c 'echo p > /proc/sysrq-trigger'
CPU: 0 PMU registers, ppmu = POWER8 n_counters = 6
PMC1: 5b635e38 PMC2: 00000000 PMC3: 00000000 PMC4: 00000000
PMC5: 1bf5a646 PMC6: 5793d378 PMC7: deadbeef PMC8: deadbeef
MMCR0: 0000000080000000 MMCR1: 000000001e000000 MMCRA: 0000040000000000
MMCR2: fffffffffffffc00 EBBHR: 0000000000000000
EBBRR: 0000000000000000 BESCR: 0000000000000000
SIAR: 00000000000a51cc SDAR: c00000000fc40000 SIER: 0000000001000000
This is done unconditionally in book3s_hv_interrupts.S upon entering the
guest, and the original value is only save/restored if the host has
indicated it was using the PMU. This is okay, however the user of the
PMU needs to ensure that it is in a defined state when it starts using
it.
Fixes: e05b9b9e5c ("powerpc/perf: Power8 PMU support")
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of separate bits for every POWER8 PMU feature, have a single one
for v2.07 of the architecture.
This saves us adding a MMCR2 define for a future patch.
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These two registers are already saved in the block above. Aside from
being unnecessary, by the time we get down to the second save location
r8 no longer contains MMCR2, so we are clobbering the saved value with
PMC5.
MMCR2 primarily consists of counter freeze bits. So restoring the value
of PMC5 into MMCR2 will most likely have the effect of freezing
counters.
Fixes: 72cde5a88d ("KVM: PPC: Book3S HV: Save/restore host PMU registers that are new in POWER8")
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 8d6f7c5a: "powerpc/powernv: Make it possible to skip the IRQHAPPENED
check in power7_nap()" added code that prevents cpus from checking for
pending interrupts just before entering sleep state, which is wrong. These
interrupts are delivered during the soft irq disabled state of the cpu.
A cpu cannot enter any idle state with pending interrupts because they will
never be serviced until the next time the cpu is woken up by some other
interrupt. Its only then that the pending interrupts are replayed. This can result
in device timeouts or warnings about this cpu being stuck.
This patch fixes ths issue by ensuring that cpus check for pending interrupts
just before entering any idle state as long as they are not in the path of split
core operations.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In fb5a515704 "powerpc: Remove platforms/wsp and associated pieces",
we removed the last user of MMU_FTRS_A2. So remove it.
MMU_FTRS_A2 was the last user of MMU_FTR_TYPE_3E, so remove it also.
This leaves some unreachable code in mmu_context_nohash.c, so remove
that also.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 046d662f48 "coredump: make core dump functionality optional"
made the coredump optional, but didn't update the spufs code that
depends on it. That leads to build errors such as:
arch/powerpc/platforms/built-in.o: In function `.spufs_arch_write_note':
coredump.c:(.text+0x22cd4): undefined reference to `.dump_emit'
coredump.c:(.text+0x22cf4): undefined reference to `.dump_emit'
coredump.c:(.text+0x22d0c): undefined reference to `.dump_align'
coredump.c:(.text+0x22d48): undefined reference to `.dump_emit'
coredump.c:(.text+0x22e7c): undefined reference to `.dump_skip'
Fix it by adding some ifdefs in the cell code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull kbuild fixes from Michal Marek:
"Three more fixes for the relative build dir feature:
- Shut up make -s again
- Fix for rpm/deb/tar-pkg with O=<subdir>
- Fix for CONFIG_EXTRA_FIRMWARE"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
firmware: Create directories for external firmware
kbuild: Fix packaging targets with relative $(srctree)
kbuild: Do not print the build directory with make -s
- Missing device ID for ACPI enumeration of PNP devices that we
overlooked during the recent rework of that code from Zhang Rui.
- Fix for a problem introduced during the 3.14 cycle in the ACPI
device resources management code and causing it to reject all
resources of length 0 although some of them are actually valid
which affects serial ports detection on a number of systems.
From Andy Whitcroft.
- intel_pstate fix for a boot problem on some BayTrail-based
systems introduced by a previous fix related to that platform
during the 3.13 cycle from Dirk Brandewie.
- Revert of a 3.13 commit that removed the ACPI AC /proc interface
which turns out to be still needed by some old utilities (kpowersave
from kde 3.5.10 in particular) from Lan Tianyu.
- cpufreq build fix for the davinci ARM platform from Prabhakar Lad
(the breakage was introduced during the 3.10 cycle).
- ACPI-related i915 fix preventing firmware on some Thinkpad laptops
from setting backlight levels incorrectly during AC plug/unplug.
From Aaron Lu.
- Fixes for two nasty race conditions in the ACPI embedded controller
driver that may be responsible for a number of past bug reports
related to the EC from Lv Zhang and a fix for two memory leaks in
error code paths in that driver from Colin Ian King.
- Fixes for a couple of corner-case issues in the intel_pstate
driver (all candidates for -stable) from Dirk Brandewie and
Vincent Minet.
- Fixes for two corner-case issues in the ACPI battery driver
from Josef Gajdusek and Lan Tianyu.
- Two new ACPI video blacklist entries for Acer TravelMate B113
and Dell Inspiron 5737 from Edward Lin and Martin Kepplinger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=1zjY
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are a few regression fixes for ACPI device enumeration and
resources management, intel_pstate and cpufreq, a revert of an ACPI
commit removing user space interfaces in /proc that we incorrectly
thought were not used any more, fixes for some long-standing
concurrency issues in the ACPI EC driver, two ACPI battery driver
fixes, stable-candidate fixes for intel_pstate, an ACPI-related fix
for i915 and two new ACPI video blacklist entries for Win8-oriented
BIOSes.
Specifics:
- Missing device ID for ACPI enumeration of PNP devices that we
overlooked during the recent rework of that code from Zhang Rui.
- Fix for a problem introduced during the 3.14 cycle in the ACPI
device resources management code and causing it to reject all
resources of length 0 although some of them are actually valid
which affects serial ports detection on a number of systems. From
Andy Whitcroft.
- intel_pstate fix for a boot problem on some BayTrail-based systems
introduced by a previous fix related to that platform during the
3.13 cycle from Dirk Brandewie.
- Revert of a 3.13 commit that removed the ACPI AC /proc interface
which turns out to be still needed by some old utilities
(kpowersave from kde 3.5.10 in particular) from Lan Tianyu.
- cpufreq build fix for the davinci ARM platform from Prabhakar Lad
(the breakage was introduced during the 3.10 cycle).
- ACPI-related i915 fix preventing firmware on some Thinkpad laptops
from setting backlight levels incorrectly during AC plug/unplug.
From Aaron Lu.
- Fixes for two nasty race conditions in the ACPI embedded controller
driver that may be responsible for a number of past bug reports
related to the EC from Lv Zhang and a fix for two memory leaks in
error code paths in that driver from Colin Ian King.
- Fixes for a couple of corner-case issues in the intel_pstate driver
(all candidates for -stable) from Dirk Brandewie and Vincent Minet.
- Fixes for two corner-case issues in the ACPI battery driver from
Josef Gajdusek and Lan Tianyu.
- Two new ACPI video blacklist entries for Acer TravelMate B113 and
Dell Inspiron 5737 from Edward Lin and Martin Kepplinger"
* tag 'pm+acpi-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PNP: add soc_button_array device ID to PNP IDs list
cpufreq: Makefile: fix compilation for davinci platform
ACPI / video: Add Acer TravelMate B113 to native backlight blacklist
ACPI / video: Add Dell Inspiron 5737 to the blacklist
ACPI / i915: ignore firmware requests for backlight change
ACPI / battery: fix wrong value of capacity_now reported when fully charged
ACPI / resources: only reject zero length resources based at address zero
ACPI / battery: Retry to get battery information if failed during probing
ACPI / EC: Free saved_ec on error exit path
ACPI / EC: Add detailed fields debugging support of EC_SC(R).
ACPI / EC: Update revision due to recent changes
ACPI / EC: Fix race condition in ec_transaction_completed()
ACPI / EC: Remove duplicated ec_wait_ibf0() waiter
ACPI / EC: Add asynchronous command byte write support
ACPI / EC: Avoid race condition related to advance_transaction()
intel_pstate: Set CPU number before accessing MSRs
intel_pstate: Update documentation of {max,min}_perf_pct sysfs files
intel_pstate: don't touch turbo bit if turbo disabled or unavailable.
intel_pstate: Fix setting VID
Revert "ACPI / AC: Remove AC's proc directory."
This new request drops the pageflipping fixes for now. Just a few small
fixes for dpm, DP, and a fix for a hang on boot evergreen.
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: Reenabling SS on Cayman
drm/radeon: fix typo in ci_stop_dpm()
drm/radeon: fix typo in golden register setup on evergreen
drm/radeon: only print meaningful VM faults
drm/radeon/dp: return -EIO for flags not zero case
Replace open-coded test for empty tx ring buffer with equivalent
helper function, uart_circ_empty(). No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 717f3bbab3,
'serial_core: Fix conditional start_tx on ring buffer not empty'
exposes an incorrect assumption in several drivers' start_tx methods;
the tx ring buffer can, in fact, be empty when restarting tx while
performing flow control.
Affected drivers:
sunsab.c
ip22zilog.c
pmac_zilog.c
sunzilog.c
m32r_sio.c
imx.c
Other in-tree serial drivers either are not affected or already
test for empty tx ring buffer before transmitting.
Test for empty tx ring buffer in start_tx() method, after transmitting
x_char (if applicable).
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Seth Bollinger <sethb@digi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the exynos cpuidle driver works correctly only on exynos4210
and 5250. Trying to use it with just one CPU online on any other exynos
SoCs will lead to system failure, due to unsupported AFTR mode on other
SoCs. This patch fixes the problem by registering the driver only on
supported SoCs and letting others simply use default WFI mode until
support for them is added.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
John W. Linville says:
====================
pull request: wireless 2014-07-10
Please pull this batch of fixes intended for the 3.16 stream!
For the iwlwifi bits, Emmanuel says:
"I have here 2 patches that disable the usage of CTS to self. This
keeps making trouble to the firmware and is not a really reliable
protection anyway. We may re-enable it in the future, but in rarer
cases. Along with this, I have a fix from Ilan that prevents a
firmware assertion."
On top of that...
Amitkumar Karwar provides an mwifiex fix to properly initialize
(i.e. zero) tx_info/rx_info.
Andrea Merello stops rt2800usb from doing DMA operations on the
stack...yikes!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Relying on static functions used just once to get inlined (and
subsequently have dead code paths eliminated) is wrong: Compilers are
free to decide whether they do this, regardless of optimization level.
With this not happening for vdso_addr() (observed with gcc 4.1.x), an
unresolved reference to align_vdso_addr() causes the build to fail.
[ hpa: vdso_addr() is never actually used on x86-32, as calculate_addr
in map_vdso() is always false. It ought to be possible to clean
this up further, but this fixes the immediate problem. ]
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/53B5863B02000078000204D5@mail.emea.novell.com
Acked-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Adding the optional clock property for the mfc_pd for
handling the re-parenting while pd on/off.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds IDs for MUX clocks to be used by power domain for MFC
for doing re-parenting while pd on/off.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
While powering on/off a local powerdomain in exynos5 chipsets, the
input clocks to each device gets modified. This behaviour is based
on the SYSCLK_SYS_PWR_REG registers.
E.g. SYSCLK_MFC_SYS_PWR_REG = 0x0, the parent of input clock to MFC
(aclk333) gets modified to oscclk
= 0x1, no change in clocks.
The recommended value of SYSCLK_SYS_PWR_REG before power gating any
domain is 0x0. So we must also restore the clocks while powering on
a domain everytime.
This patch adds the framework for getting the required mux and parent
clocks through a power domain device node. With this patch, while
powering off a domain, parent is set to oscclk and while powering back
on, its re-set to the correct parent which is as per the recommended
pd on/off sequence.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Certain ld versions (observed with 2.20.0) put an empty .rela.dyn
section into shared object files, breaking the assumption on the number
of sections to be copied to the final output. Simply discard any empty
SHT_REL and SHT_RELA sections to address this.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/53B5861E02000078000204D1@mail.emea.novell.com
Acked-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
It reverts commit c745fe611c now that
Cayman is stable since VDDCI fix. Spread spectrum was not the culprit.
This depends on b0880e87c1
(drm/radeon/dpm: fix vddci setup typo on cayman).
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Need to use the RREG32_SMC() accessor since the register
is an smc indirect index.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
If there are error flags in the aux transaction return
-EIO rather than -EBUSY. -EIO restarts the whole transaction
while -EBUSY jus retries. Fixes problematic aux transfers.
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80684
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
restart handling and phy regulators and SATA interconnect data.
Also few build fixes related to the DSP driver in staging, and trivial
stuff like removal of broken and soon to be unused platform data init
for HDMI audio that would be good to get into the -rc series if not
too late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=paeu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.16-rc4" from Tony Lindgren:
Fixes for omaps for the -rc series. It's mostly fixes for clock rates,
restart handling and phy regulators and SATA interconnect data.
Also few build fixes related to the DSP driver in staging, and trivial
stuff like removal of broken and soon to be unused platform data init
for HDMI audio that would be good to get into the -rc series if not
too late.
* tag 'omap-for-v3.16/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
ARM: dts: am335x-evm: Enable the McASP FIFO for audio
ARM: OMAP2+: Make GPMC skip disabled devices
ARM: OMAP2+: create dsp device only on OMAP3 SoCs
ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
ARM: DRA7: hwmod: Fixup SATA hwmod
ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
ARM: dts: dra7xx-clocks: Fix the l3 and l4 clock rates
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit e80991773 ("dm mpath: push back requests instead of queueing")
modified multipath_busy() to return true if !pg_ready(). pg_ready()
checks the current state of the multipath device and may return false
even if a new IO is needed to change the state.
Bart Van Assche reported that he had multipath IO lockup when he was
performing cable pull tests. Analysis showed that the multipath
device had a single path group with both paths active, but that the
path group itself was not active. During the multipath device state
transitions 'queue_io' got set but nothing could clear it. Clearing
'queue_io' only happens in __choose_pgpath(), but it won't be called
if multipath_busy() returns true due to pg_ready() returning false
when 'queue_io' is set.
As such the !pg_ready() check in multipath_busy() is wrong because new
IO will not be sent to multipath target and the multipath state change
won't happen. That results in multipath IO lockup.
The intent of multipath_busy() is to avoid unnecessary cycles of
dequeue + request_fn + requeue if it is known that the multipath
device will requeue.
Such "busy" situations would be:
- path group is being activated
- there is no path and the multipath is setup to requeue if no path
Fix multipath_busy() to return "busy" early only for these specific
situations.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.15
There's a race condition between the atomic_dec_and_test(&io->count)
in dec_count() and the waking of the sync_io() thread. If the thread
is spuriously woken immediately after the decrement it may exit,
making the on stack io struct invalid, yet the dec_count could still
be using it.
Fix this race by using a completion in sync_io() and dec_count().
Reported-by: Minfei Huang <huangminfei@ucloud.cn>
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
The commit 2c140a246d ("dm: allow remove to be deferred") introduced a
deferred removal feature for the device mapper. When this feature is
used (by passing a flag DM_DEFERRED_REMOVE to DM_DEV_REMOVE_CMD ioctl)
and the user tries to remove a device that is currently in use, the
device will be removed automatically in the future when the last user
closes it.
Device mapper used the system workqueue to perform deferred removals.
However, some targets (dm-raid1, dm-mpath, dm-stripe) flush work items
scheduled for the system workqueue from their destructor. If the
destructor itself is called from the system workqueue during deferred
removal, it introduces a possible deadlock - the workqueue tries to flush
itself.
Fix this possible deadlock by introducing a new workqueue for deferred
removals. We allocate just one workqueue for all dm targets. The
ability of dm targets to process IOs isn't dependent on deferred removal
of unused targets, so a deadlock due to shared workqueue isn't possible.
Also, cleanup local_init() to eliminate potential for returning success
on failure.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.13+
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-cpufreq:
cpufreq: Makefile: fix compilation for davinci platform
intel_pstate: Set CPU number before accessing MSRs
intel_pstate: Update documentation of {max,min}_perf_pct sysfs files
intel_pstate: don't touch turbo bit if turbo disabled or unavailable.
intel_pstate: Fix setting VID
* acpi-resources:
ACPI / resources: only reject zero length resources based at address zero
* acpi-ac:
Revert "ACPI / AC: Remove AC's proc directory."
* acpi-scan:
ACPI / PNP: add soc_button_array device ID to PNP IDs list
* acpi-battery:
ACPI / battery: fix wrong value of capacity_now reported when fully charged
ACPI / battery: Retry to get battery information if failed during probing
Pull libata fixes from Tejun Heo:
"Nothing too interesting. All fixes are ahci_platform related"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_xgene: fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode command.
libahci: export ahci_qc_issue() and ahci_start_fix_rx()
ata: ahci_imx: warn when disabling ahci link
ahci: disable ncq feature for hisilicon sata
ahci: imx: manage only sata_ref_clk in imx_sata_enable[disable]
libahci_platform: Fail when PHY required but PHY support disabled
Pull cgroup fixes from Tejun Heo:
"Mostly fixes for the fallouts from the recent cgroup core changes.
The decoupled nature of cgroup dynamic hierarchy management
(hierarchies are created dynamically on mount but may or may not be
reused once unmounted depending on remaining usages) led to more
ugliness being added to kernfs.
Hopefully, this is the last of it"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: break kernfs active protection in cpuset_write_resmask()
cgroup: fix a race between cgroup_mount() and cgroup_kill_sb()
kernfs: introduce kernfs_pin_sb()
cgroup: fix mount failure in a corner case
cpuset,mempolicy: fix sleeping function called from invalid context
cgroup: fix broken css_has_online_children()
Pull workqueue fixes from Tejun Heo:
"Two workqueue fixes. Both are one liners. One fixes missing uevent
for workqueue files on sysfs. The other one fixes missing zeroing of
NUMA cpu masks which can lead to oopses among other things"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: zero cpumask of wq_numa_possible_cpumask on init
workqueue: fix dev_set_uevent_suppress() imbalance
Pull percpu fix from Tejun Heo:
"One patch to fix a typo in percpu section name. Given how long the
bug has been there and that there hasn't been any report of brekage,
it's unlikely to cause actual issues"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
core: fix typo in percpu read_mostly section
