Christoph correctly points out that this issue is no different
for other block devices, and poking at cross layer internals
is not the right way to solve it.
This reverts commit bb6aa6f082.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Implement a generic path for sending sync I/O on LightNVM. This allows
to reuse the standard synchronous path trough blk_execute_rq(), instead
of implementing a wait_for_completion on the target side (e.g., pblk).
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Not all exported symbols are being used outside core and there were
some stale entries in lightnvm.h
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
vblk isn't being used anyway and if we ever have a usecase we can
introduce this again. This makes the logic easier and removes
unnecessary checks.
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove repeated calculation for number of channels while creating a
target device.
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvm_tgt_types list was protected by wrong lock for NVM_INFO ioctl call
and can race with addition or removal of target types. Also
unregistering target type was not protected correctly.
Fixes: 5cd907853 ("lightnvm: remove nested lock conflict with mm")
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a virtual block device is formatted and mounted after creating
with "nvme lnvm create... -t pblk", a removal from "nvm lnvm remove"
would result in this:
446416.309757] bdi-block not registered
[446416.309773] ------------[ cut here ]------------
[446416.309780] WARNING: CPU: 3 PID: 4319 at fs/fs-writeback.c:2159
__mark_inode_dirty+0x268/0x340
Ideally removal should return -EBUSY as block device is mounted after
formatting. This patch tries to address this checking if whole device
or any partition of it already mounted or not before removal.
Whole device is checked using "bd_super" member of block device. This
member is always set once block device has been mounted using a
filesystem. Another member "bd_part_count" takes care of checking any
if any partitions are under use. "bd_part_count" is only updated
under locks when partitions are opened or closed (first open and last
release). This at least does take care sending -EBUSY if removal is
being attempted while whole block device or any partition is mounted.
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If target type module e.g. pblk here is unloaded (rmmod) while module
is in use (after creating target) system crashes. We fix this by
using module API refcnt.
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While creating new device with NVM_DEV_CREATE if LUNs are already
allocated ioctl would return -ENOMEM which is wrong. This patch
propagates -EBUSY from nvm_reserve_luns which is correct response.
Fixes: ade69e243 ("lightnvm: merge gennvm with core")
Reviewed-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In case of a failure when submitting a request, convert the ppa_list
addresses to the target format so that it can interpret ppas for
recovery
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Free memory correctly when an allocation fails on a loop and we free
backwards previously successful allocations.
Signed-off-by: Javier González <javier@cnexlabs.com>
Reviewed-by: Matias Bjørling <matias@cnexlabs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
From userspace calling ioctl(NVM_DEV_CREATE) was returning ENOMEM for
invalid arguments even though pblk (pblk_init) was returning correctly
-EINVAL to nvm_create_tgt inside core. This patch propagates the
correct return value to userspace.
Because pblk was introduced recently this only needs to go in 4.12.
Fixes: a4bd217b43 ("lightnvm: physical block device (pblk) target")
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Convert sprintf calls to strlcpy in order to make possible buffer
overflow more obvious.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Prefix the nvm_free static function with a missing static keyword.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Target initialization has two responsibilities: creating the target
partition and instantiating the target. This patch enables to create a
factory partition (e.g., do not trigger recovery on the given target).
This is useful for target development and for being able to restore the
device state at any moment in time without requiring a full-device
erase.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Reorder disk allocation such that the disk structure can be put
safely.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The dev->lun_map bits are cleared twice if an target init error occurs.
First in the target clean routine, and then next in the nvm_tgt_create
error function. Make sure that it is only cleared once by extending
nvm_remove_tgt_devi() with a clear bit, such that clearing of bits can
ignored when cleaning up a successful initialized target.
Signed-off-by: Javier González <javier@cnexlabs.com>
Fix style.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Until now erases have been submitted as synchronous commands through a
dedicated erase function. In order to enable targets implementing
asynchronous erases, refactor the erase path so that it uses the normal
async I/O submission functions. If a target requires sync I/O, it can
implement it internally. Also, adapt rrpc to use the new erase path.
Signed-off-by: Javier González <javier@cnexlabs.com>
Fixed spelling error.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The create target ioctl takes a lun begin and lun end parameter, which
defines the range of luns to initialize a target with. If the user does
not set the parameters, it default to only using lun 0. Instead,
defaults to use all luns in the OCSSD, as it is the usual behaviour
users want.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If one specifies the end lun id to be the absolute number of luns,
without taking zero indexing into account, the lightnvm core will pass
the off-by-one end lun id to target creation, which then panics during
nvm_ioctl_dev_create.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to register through the sysfs interface, a driver needs to know
its kobject. On a disk structure, this happens when the partition
information is added (device_add_disk), which for lightnvm takes place
after the target has been initialized. This means that on target
initialization, the kboject has not been created yet.
This patch adds a target function to let targets initialize their own
kboject as a child of the disk kobject.
Signed-off-by: Javier González <javier@cnexlabs.com>
Added exit typedef and passed gendisk instead of void pointer for exit.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix a memory leak when target creation fails. More specifically, free
the entire device structure given to the target (tgt_dev).
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When the lightnvm core had the "gennvm" layer between the device and the
target, there was a need for the core to be able to figure out which
target it should send an end_io callback to. Leading to a "double"
end_io, first for the media manager instance, and then for the target
instance. Now that core and gennvm is merged, there is no longer a need
for this, and a single end_io callback will do.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The number of configuration groups has been limited to one in current
code, even if there is support for up to four. With the introduction
of the open-channel SSD 1.3 specification, only a single
group is exposed onwards. Reflect this in the nvm_id structure.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Going from target specific ppa addresses to device was accomplished by
first converting target to generic ppa addresses and generic to device
addresses. The conversion was either open-coded or used the built-in
nvm_trans_* and nvm_map_* functions for conversion. Simplify the
interface and cleanup the calls to provide clean functions that now
either take a list of ppas or a nvm_rq, and is exposed through:
void nvm_ppa_* - target to/from device with a list of PPAs,
void nvm_rq_* - target to/from device with a nvm_rq.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The only check there was done was a debugging check. Remove it and
replace the return value with void to reduce error checking.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since the merge of gennvm and core, there is no longer a need for the
device specific bad block functions.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The nvm_submit_ppa* functions are no longer needed after gennvm and core
have been merged.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
After gennvm and core have been merged, there are no more callers to
nvm_erase_ppa. Therefore collapse the device specific and target
specific erase functions.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For the first iteration of Open-Channel SSDs, it was anticipated that
there could be various media managers on top of an open-channel SSD,
such to allow vendors to plug in their own host-side FTLs, without the
media manager in between.
Now that an Open-Channel SSD is exposed as a traditional block device,
there is no longer a need for this. Therefore lets merge the gennvm code
with core and simplify the stack.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAtwA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyCgCeJn36u1AsBi7qZ3u/1hwD8k56s2IAnRo6U31r
WW65YcNTK7qYXqNbfgIa
=/t/V
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (107 commits)
uio-hv-generic: store physical addresses instead of virtual
Tools: hv: kvp: configurable external scripts path
uio-hv-generic: new userspace i/o driver for VMBus
vmbus: add support for dynamic device id's
hv: change clockevents unbind tactics
hv: acquire vmbus_connection.channel_mutex in vmbus_free_channels()
hyperv: Fix spelling of HV_UNKOWN
mei: bus: enable non-blocking RX
mei: fix the back to back interrupt handling
mei: synchronize irq before initiating a reset.
VME: Remove shutdown entry from vme_driver
auxdisplay: ht16k33: select framebuffer helper modules
MAINTAINERS: add git url for fpga
fpga: Clarify how write_init works streaming modes
fpga zynq: Fix incorrect ISR state on bootup
fpga zynq: Remove priv->dev
fpga zynq: Add missing \n to messages
fpga: Add COMPILE_TEST to all drivers
uio: pruss: add clk_disable()
char/pcmcia: add some error checking in scr24x_read()
...
Since targets are given a virtual target device, it is necessary to
translate all communication between targets and the backend device.
Implement the translation layer for get/set bad block table.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
On target-specific operations pass on nvm_tgt_dev instead of the generic
nvm device.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Target devices do not have access to the device driver operations.
Introduce a helper function that exposes the max. number of physical
sectors supported by the underlying device.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid calling media manager and device-specific operations directly from
rrpc. Create helper functions on lightnvm's core instead.
Signed-off-by: Javier González <javier@cnexlabs.com>
Made it work with null_blk as well.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.
Since targets own the LUNs the are instantiated on top of and manage the
free block list internally, there is no need for a LUN abstraction in
the media manager. LUNs are intrinsically managed as in the physical
layout (ch:0,lun:0, ..., ch:0,lun:n, ch:1,lun:0, ch:1,lun:n, ...,
ch:m,lun:0, ch:m,lun:n) and given to the targets based on the target
creation ioctl. This simplifies LUN management and clears the path for a
partition manager to sit directly underneath LightNVM targets.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.
A part of this transformation is that targets manage their blocks
internally. This patch eliminates the nvm_block abstraction and moves
block management to the target logic. The rrpc target is transformed.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.
This patch moves the block provisioning inside of the target and removes
the get/put block interface from the media manager.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
LightNVM used to be managed and configured through sysfs. Since the
introduction of management ioctls this interface is redundant and
outdated. Get rid of it.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Bad blocks should be managed by block owners. This would be either
targets for data blocks or sysblk for system blocks.
In order to support this, export two functions: One to mark a block as
an specific type (e.g., bad block) and another to update the bad block
table on the device.
Move bad block management to rrpc.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Erases might be subject to host hints. An example is multi-plane
programming to erase blocks in parallel. Enable targets to specify this
hint.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Previously, LBA read and write were not supported in the lightnvm
specification. Now that it supports it, lets use the traditional
NVMe gendisk, and attach the lightnvm sysfs geometry export.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The Kconfig currently controlling compilation of this code is:
drivers/lightnvm/Kconfig:menuconfig NVM
drivers/lightnvm/Kconfig: bool "Open-Channel SSD target support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_misc_driver translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with moduleparam.h because this file still uses
module params to control behaviour.
Also note that MODULE_ALIAS is a no-op for non-modular code.
Cc: Matias Bjorling <mb@lightnvm.io>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull block layer updates from Jens Axboe:
"This is the main pull request for block layer changes in 4.9.
As mentioned at the last merge window, I've changed things up and now
do just one branch for core block layer changes, and driver changes.
This avoids dependencies between the two branches. Outside of this
main pull request, there are two topical branches coming as well.
This pull request contains:
- A set of fixes, and a conversion to blk-mq, of nbd. From Josef.
- Set of fixes and updates for lightnvm from Matias, Simon, and Arnd.
Followup dependency fix from Geert.
- General fixes from Bart, Baoyou, Guoqing, and Linus W.
- CFQ async write starvation fix from Glauber.
- Add supprot for delayed kick of the requeue list, from Mike.
- Pull out the scalable bitmap code from blk-mq-tag.c and make it
generally available under the name of sbitmap. Only blk-mq-tag uses
it for now, but the blk-mq scheduling bits will use it as well.
From Omar.
- bdev thaw error progagation from Pierre.
- Improve the blk polling statistics, and allow the user to clear
them. From Stephen.
- Set of minor cleanups from Christoph in block/blk-mq.
- Set of cleanups and optimizations from me for block/blk-mq.
- Various nvme/nvmet/nvmeof fixes from the various folks"
* 'for-4.9/block' of git://git.kernel.dk/linux-block: (54 commits)
fs/block_dev.c: return the right error in thaw_bdev()
nvme: Pass pointers, not dma addresses, to nvme_get/set_features()
nvme/scsi: Remove power management support
nvmet: Make dsm number of ranges zero based
nvmet: Use direct IO for writes
admin-cmd: Added smart-log command support.
nvme-fabrics: Add host_traddr options field to host infrastructure
nvme-fabrics: revise host transport option descriptions
nvme-fabrics: rework nvmf_get_address() for variable options
nbd: use BLK_MQ_F_BLOCKING
blkcg: Annotate blkg_hint correctly
cfq: fix starvation of asynchronous writes
blk-mq: add flag for drivers wanting blocking ->queue_rq()
blk-mq: remove non-blocking pass in blk_mq_map_request
blk-mq: get rid of manual run of queue with __blk_mq_run_hw_queue()
block: export bio_free_pages to other modules
lightnvm: propagate device_add() error code
lightnvm: expose device geometry through sysfs
lightnvm: control life of nvm_dev in driver
blk-mq: register device instead of disk
...
For a host to access an Open-Channel SSD, it has to know its geometry,
so that it writes and reads at the appropriate device bounds.
Currently, the geometry information is kept within the kernel, and not
exported to user-space for consumption. This patch exposes the
configuration through sysfs and enables user-space libraries, such as
liblightnvm, to use the sysfs implementation to get the geometry of an
Open-Channel SSD.
The sysfs entries are stored within the device hierarchy, and can be
found using the "lightnvm" device type.
An example configuration looks like this:
/sys/class/nvme/
└── nvme0n1
├── capabilities: 3
├── device_mode: 1
├── erase_max: 1000000
├── erase_typ: 1000000
├── flash_media_type: 0
├── media_capabilities: 0x00000001
├── media_type: 0
├── multiplane: 0x00010101
├── num_blocks: 1022
├── num_channels: 1
├── num_luns: 4
├── num_pages: 64
├── num_planes: 1
├── page_size: 4096
├── prog_max: 100000
├── prog_typ: 100000
├── read_max: 10000
├── read_typ: 10000
├── sector_oob_size: 0
├── sector_size: 4096
├── media_manager: gennvm
├── ppa_format: 0x380830082808001010102008
├── vendor_opcode: 0
├── max_phys_secs: 64
└── version: 1
Signed-off-by: Simon A. F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
LightNVM compatible device drivers does not have a method to expose
LightNVM specific sysfs entries.
To enable LightNVM sysfs entries to be exposed, lightnvm device
drivers require a struct device to attach it to. To allow both the
actual device driver and lightnvm sysfs entries to coexist, the device
driver tracks the lifetime of the nvm_dev structure.
This patch refactors NVMe and null_blk to handle the lifetime of struct
nvm_dev, which eliminates the need for struct gendisk when a lightnvm
compatible device is provided.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
With LightNVM enabled namespaces, the gendisk structure is not exposed
to the user. This prevents LightNVM users from accessing the NVMe device
driver specific sysfs entries, and LightNVM namespace geometry.
Refactor the revalidation process, so that a namespace, instead of a
gendisk, is revalidated. This later allows patches to wire up the
sysfs entries up to a non-gendisk namespace.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Jens Axboe