This patch improves the sequence the resources are released by, first,
- disabling the IRQ in the controller, then by
- resetting the DMA logic, and finally, by
- adding a read cycle to ensure that the above commands have been received
before freeing the system interrupt.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes a typo in the error message in pciefd_can_probe().
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This cosmetic change should facilitate in the future the use of MSI
rather than legacy INTx interrupts.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANFD_IRQ_SET as well as CANFD_TX_PATH_SET are not used.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The embedded firmware aligns its messages on 32-bit boundaries.
This patch makes sure to browse through the list of received messages
while respecting 32-bit alignment.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards
family is not capable of handling a mix of 32-bit and 64-bit logical
addresses. If the board is equipped with 2 or 4 CAN ports, then such a
situation might lead to a PCIe Bus Error "Malformed TLP" packet
as well as "irq xx: nobody cared" issue.
This patch adds a workaround that requests only 32-bit DMA addresses
when these might be allocated outside of the 4 GB area.
This issue has been fixed in firmware v3.3.0 and next.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When an interface starts, the echo_skb array is empty and the network
queue should be started only. This patch replaces useless code and locks
when the internal RX_BARRIER message is received from the IP core, telling
the driver that tx may start.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch makes atomic the handling of the linux-can echo_skb array and
the network tx queue. This prevents from the "BUG! echo_skb is occupied!"
message to be printed by the linux-can core, in SMP environments.
Reported-by: Diana Burgess <diana@peloton-tech.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
PCI/PCIe drivers for PEAK-System CAN/CAN-FD interfaces do some access to the
PCI config during probing. In case one of these accesses fails, a POSITIVE
PCIBIOS_xxx error code is returned back. This POSITIVE error code MUST be
converted into a NEGATIVE errno for the probe() function to indicate it
failed. Using the pcibios_err_to_errno() function, we make sure that the
return code will always be negative.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds support for the following PEAK-System CAN FD interfaces:
PCAN-cPCIe FD CAN FD Interface for cPCI Serial (2 or 4 channels)
PCAN-PCIe/104-Express CAN FD Interface for PCIe/104-Express (1, 2 or 4 ch.)
PCAN-miniPCIe FD CAN FD Interface for PCIe Mini (1, 2 or 4 channels)
PCAN-PCIe FD OEM CAN FD Interface for PCIe OEM version (1, 2 or 4 ch.)
PCAN-M.2 CAN FD Interface for M.2 (1 or 2 channels)
Like the PCAN-PCIe FD interface, all of these boards run the same IP Core
that is able to handle CAN FD (see also http://www.peak-system.com).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes two uninitialized symbol warnings in the new code adding
support of the PEAK-System PCAN-PCI Express FD boards, in the socket-CAN
network protocol family.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support of the PCAN-PCI Express FD boards made
by PEAK-System, for computers using the PCI Express slot.
The PCAN-PCI Express FD has one or two CAN FD channels, depending
on the model. A galvanic isolation of the CAN ports protects
the electronics of the card and the respective computer against
disturbances of up to 500 Volts. The PCAN-PCI Express FD can be operated
with ambient temperatures in a range of -40 to +85 °C.
Such boards run an extented version of the CAN-FD IP running into USB
CAN-FD interfaces from PEAK-System, so this patch adds several new commands
and their corresponding data types to the PEAK CAN-FD common definitions
header file too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
