After calling phy_select_page() and until calling phy_restore_page(),
the mutex 'mdio_lock' is already locked, so the driver should use
non-locked version of phy functions. Or there will be a deadlock with
'mdio_lock'.
This replaces phy functions called from rtl8211e_config_init() to avoid
the deadlock issue.
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding missing callbacks I missed that one had them set already.
Interesting that the compiler didn't complain.
Fixes: daf3ddbe11 ("net: phy: realtek: add missing page operations")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing page operation callbacks to few Realtek drivers.
This also fixes a NPE after the referenced commit added code to the
RTL8211E driver that uses phy_select_page().
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's prone to problems if delay is cleared out for other than RGMII
modes. So lets set/clear the TX-delay in the config register only
if actually RGMII-like interface mode is requested. This only
concerns rtl8211f chips.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. Alas this is the only
documented info regarding the RGMII timing control configurations the PHY
provides. It turns out the same settings can be setup via MDIO registers
hidden in the extension pages layout. Particularly the extension page 0xa4
provides a register 0x1c, which bits 1 and 2 control the described delays.
They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.
The hidden RGMII configs register utilization was found in the rtl8211e
U-boot driver:
https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99
There is also a freebsd-folks discussion regarding this register:
https://reviews.freebsd.org/D13591
It confirms that the register bits field must control the so called
configuration pins described in the table 12-13 of the official PHY
datasheet:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phylib uses genphy_read_abilities() as fallback, we don't have
to set callback get_features any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_read_abilities(). This allows to remove all
calls to genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY's of later RTL8168 network chips report the generic
PHYID 0x001cc800 (Realtek OUI, model and revision number both set to
zero) and therefore currently the genphy driver is used.
To be able to use the paged version of e.g. phy_write() we need a
PHY driver with the read_page and write_page callbacks implemented.
So basically make a copy of the genphy driver, just with the
read_page and write_page callbacks being set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new macros for PHYID matching to avoid boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of listing every single PHYID, load the driver for every PHYID
with a Realtek OUI, independent of model number and revision.
This patch also improves two further aspects:
- constify realtek_tbl[]
- the mask should have been 0xffffffff instead of 0x001fffff so far,
by masking out some bits a PHY from another vendor could have been
matched
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366RB is an ASIC with five internal PHYs for
LAN0..LAN3 and WAN. The PHYs are spawn off the main
device so they can be handled in a distributed manner
by the Realtek PHY driver. All that is really needed
is the power save feature enablement and letting the
PHY driver core pick up the IRQ from the switch chip.
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing entry for RTL8211C to mdio_device_id table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: cf87915cb9 ("net: phy: realtek: add support for RTL8211C")
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8211C has an issue when operating in Gigabit slave mode, therefore
genphy driver can't be used. See also this U-boot change.
https://lists.denx.de/pipermail/u-boot/2016-March/249712.html
Add a PHY driver for this chip with the quirk to force Gigabit master
mode. As a note: This will make it impossible to connect two network
ports directly which both are driven by a RTl8211C.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for RTL8211 I forgot to update the mdio_device_id
table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: d241d4aac9 ("net: phy: realtek: add support for RTL8211")
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of adding phylib support to the r8169 driver we need
PHY drivers for all chip-internal PHY types. Fortunately almost all
of them are either supported by the Realtek PHY driver already or work
with the genphy driver.
Still missing is support for the PHY of RTL8169s, it requires a quirk
to properly support 100Mbit-fixed mode. The quirk was copied from
r8169 driver which copied it from the vendor driver.
Based on the PHYID the internal PHY seems to be a RTL8211.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet on mpc8315erdb is broken since commit b6b5e8a691
("gianfar: Disable EEE autoneg by default"). The reason is that
even though the rtl8211b doesn't support the MMD extended registers
access, it does return some random values if we trying to access
the MMD register via indirect method. This makes it seem that the
EEE is supported by this phy device. And the subsequent writing to
the MMD registers does cause the phy malfunction. So use the dummy
stubs for the MMD register access to fix this issue.
Fixes: b6b5e8a691 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new helpers for paged register access.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek PHYs implement the concept of so-called "extension pages". The
reason for this is probably because these PHYs expose more registers
than available in the standard address range.
After all read/write operations on such a page are done the driver
should switch back to page 0 where the standard MII registers (such as
MII_BMCR) are available.
When referring to such a register the datasheets of RTL8211E and
RTL8211F always specify:
- the page / "ext. page" which has to be written to RTL821x_PAGE_SELECT
- an address (sometimes also called reg)
These new utility functions make the existing code easier to read since
it removes some duplication (switching back to page 0 is done within the
new helpers for example).
No functional changes are intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply makes the code easier to read. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply moves all register bit #defines which describe the (PHY
specific) bits in the RTL821x_INER right below the RTL821x_INER register
definition. This makes it easier to spot which registers and bits belong
together.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This macro is only used by the RTL8211B code. RTL8211E and RTL8211F both
use other bits to initialize the RTL821x_INER register.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it easier to compare the #defines with the datasheets.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit b94d22d94a "ARM64: dts: meson-gx: add external PHY
interrupt on some platforms" ethernet stopped working on my Odroid-C2
which has a RTL8211F phy.
It turned out that no interrupts were triggered. Further analysis
showed the register INER can't be altered on page 0.
Because register INSR needs to be accessed via page 0xa43 I assumed
that register INER needs to be accessed via some page too.
Some brute force check resulted in page 0xa42 being the right one.
With this patch the phy is working properly in interrupt mode.
Fixes: 3447cf2e9a ("net/phy: Add support for Realtek RTL8211F")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RTL8201F phy-id and the related functions to the driver.
The original patch is as follows:
https://patchwork.kernel.org/patch/2538341/
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames the definition of page select register from
RTL8211F_PAGE_SELECT to RTL821x_PAGE_SELECT to use it across models.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. There are dedicated phy-modes which tell the
PHY driver to enable the RX and/or TX delays:
- PHY_INTERFACE_MODE_RGMII should disable the RX and TX delay in the
PHY (if required, the MAC should add the delays in this case)
- PHY_INTERFACE_MODE_RGMII_ID should enable RX and TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_TXID should enable the TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_RXID should enable the RX delay in the PHY
(currently not supported by RTL8211F)
With this patch we enable the TX delay for PHY_INTERFACE_MODE_RGMII_ID
and PHY_INTERFACE_MODE_RGMII_TXID.
Additionally we now explicity disable the TX-delay, which seems to be
enabled automatically after a hard-reset of the PHY (by triggering it's
reset pin) to get a consistent state (as defined by the phy-mode).
This fixes a compatibility problem with some SoCs where the TX-delay was
also added by the MAC. With the TX-delay being applied twice the TX
clock was off and TX traffic was broken or very slow (<10Mbit/s) on
1000Mbit/s links.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8211F has different register definitions from RTL8211E.
Specially it needs to enable TXDLY in case of RGMII.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.
Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using phy_drivers_register/_unregister functions is proper way to
handle multiple PHY drivers registration. For Realtek PHY drivers
module, it fixes incomplete current error-handlings up and adds
missed unregistration for the RTL8201CP driver.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix a problem in the rtl8211 where the driver
wasn't properly enabled the interrupt on link change status.
it has to enable the ineterrupt on the bit 10 in the register 18
(INER).
Reported-by: Sharma Bhupesh <B45370@freescale.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the minimal driver to manage the
Realtek RTL8211E 10/100/1000 Transceivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If registering of one of them fails, all already registered drivers
of this module will be unregistered.
Use the new register/unregister functions in all drivers
registering more than one driver.
amd.c, realtek.c: Simplify: directly return registration result.
Tested with broadcom.c
All others compile-tested.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
MODULE_DEVICE_TABLE only expands to something if it's compiled
for a module. So when building-in support for the phys, the
mdio_device_id tables are unused. Marking them with __maybe_unused
fixes the following warnings:
drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used
drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used
drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used
drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used
drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used
drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used
drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used
drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used
drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used
drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used
drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used
drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used
drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used
drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used
drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
this PHY present on the MPC8315E and MPC837xE RDB boards.
Signed-off-by: Johnson Leung <r58129@freescale.com>
Signed-off-by: Kevin Lam <r43770@freescale.com>
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
