ALC650 has a channel swap option between surround and CLFE channels,
so we need to tweak the channel maps dynamically depending on the
register bit.
Now struct snd_ac97 can contain chmap pointers for playback and
capture. The driver may store these and let ac97 driver changing the
channel mapping dynamically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... instead of the standard fixed channel maps.
The generic HDMI is based on the audio infoframe, and its configuration
can be selected via CA bits. Thus we need a translation between the
CA index and the verbose channel map list.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although HD-audio allows pair-wise channel configurations, only the
fixed channel positions are used in this version. In future, this can
be changed and allow user to modify the channel positions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently the check for non-PCM stream state was added to the generic
HDMI driver code. But this check should be done rather to each pin
instead of each converter. Otherwise when a different converter is
assigned at the next open, the audio infoframe can be inconsistent
with the setup using the previous converter.
For fixing this issue, this patch moves the state of the current
non-PCM status from per_cvt to per_pin. (In addition an unused
argument cvt_nid is stripped from hdmi_setup_channel_mapping())
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For multiple speaker outs, the names were previously
"Speaker,0", "Speaker,1", "Center"/"LFE", "Speaker,3". This is
inconsistent, confusing, and is not picked up correctly by PulseAudio.
Instead use "Front", "Surround", "Center"/"LFE", "Side" which
is more standard.
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1046734
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For HBR stream test, use straight channel mapping way.
when switched back to "speaker-test -c8", even the audio
infoframe is up-to-date, there should be correct channel mapping setup.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDMI channel remapping apparently effects HBR packets on Intel's chips.
For compressed non-PCM audio, use "straight-through" channel mapping.
For uncompressed multi-channel pcm audio, use normal channel mapping.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The array channel_allocations[] is an ordered list, add function to get
correct order by ca_index.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The call of pm_notify callback in snd_hda_codec_free() should be with
the check of the current state whether pm_notify(false) is called or
not, instead of codec->power_on check.
For improving the code readability and fixing this inconsistency,
codec->d3_stop_clk_ok is renamed to codec->pm_down_notified, and this
flag is set only when runtime PM down is called. The new name reflects
to a more direct purpose of the flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
k1212MinADCSens and k1212MaxADCSens are defined wrongly.
The max must be greater than the min by obvious reason.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46561
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_SND_HDA_POWER_SAVE is no longer an experimental feature and its
behavior can be well controlled via the default value and module
parameter. Let's just replace it with the standard CONFIG_PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec provides its own set_power_state op, the D3-clock-stop
isn't checked correctly. And the recent changes for repeating the
state-setting operation isn't applied to such a codec, too.
This patch fixes these issues by moving the call of codec's own op to
the place where the generic power-set operation is done, and move the
power-state synchronization code out of
snd_hda_set_power_state_to_all() so that it can be called always at
the end of power-up/down sequence, and updates the D3 clock-stop flag
properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the HD-audio is removed, it leaves the refcounts when codecs are
powered up (usually yes) in the destructor. For fixing the unbalance,
and cleaning up the code mess, this patch changes the following:
- change pm_notify callback to take the explicit power on/off state,
- check of D3 stop-clock and keep_link_on flags is moved to the caller
side,
- call pm_notify callback in snd_hda_codec_new() and snd_hda_codec_free()
so that the refcounts are proprely updated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These codecs seem reporting EPSS but require longer delay for the
proper D3 transition. For example, D3_STOP_CLOCK_OK bit won't be set
correctly even after D3.
In this patch, codec->epss flag is overridden for avoid the
misbehavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EPSS parameter should be static, so we can read it once and remember.
This also allows more easily to override the wrong EPSS capability
reported from a codec by changing the flag in the codec
initialization step.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use unsigned int to make clear that the codes required only for
modules will be reduced by the compiler optimization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch to support runtime PM introduced a bug:
Module parameter 'power_save_controller', and the codec flag 'd3_stop_clk'
'd3_stop_clk_ok' are defined only when HDA power save is enabled in config. But
there are references to them without checking macro CONFIG_SND_HDA_POWER_SAVE.
This patch is to fix the bug.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Runtime PM can bring more power saving:
- When the controller is suspended, its parent device will also have a chance
to suspend.
- PCI subsystem can choose the lowest power state the controller can signal
wake up from. This state can be D3cold on platforms with ACPI PM support.
And runtime PM can provide a gerneral sysfs interface for a system policy
manager.
Runtime PM support is based on current HDA power saving implementation. The user
can enable runtime PM on platfroms that provide acceptable latency on transition
from D3 to D0.
Details:
- When both power saving and runtime PM are enabled:
-- If a codec supports 'stop-clock' in D3, it will request suspending the
controller after it enters D3 and request resuming the controller before
back to D0. Thus the controller will be suspended only when all codecs are
suspended and support stop-clock in D3.
-- User IO operations and HW wakeup signal can resume the controller back to
D0.
- If runtime PM is disabled, power saving just works as before.
- If power saving is disabled, the controller won't be suspended because the
power usage counter can never be 0.
More about 'stop-clock' feature:
If a codec can support targeted pass-through operations in D3 state when there
is no BCLK present on the link, it will set CLKSTOP flag in the supported power
states and report PS-ClkStopOk when entering D3 state. Please refer to HDA spec
section 7.3.3.10 Power state and 7.3.4.12 Supported Power State.
[Fixed CONFIG_PM_RUNTIME dependency in hda_intel.c by tiwai]
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling the jack sync in the init callback of each codec,
call it generically at initialization and resume. By calling it at
the last of resume sequence, a possible race between the jack sync and
the unsol event enablement in the current code will be closed, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes an issue with a machine where there were no speakers,
but GPIO0 had to be data=1 for the headphone to be functioning.
I'm not sure if we need a more advanced patch to solve all possible cases,
but if so, this patch would still provide a minor optimisation.
BugLink: https://bugs.launchpad.net/bugs/1040077
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the codec turn-on operation is canceled by the immediate
power-on, the driver left the power_transition flag as is.
This caused the persistent avoidance of power-save behavior.
Cc: <stable@vger.kernel.org> [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... by calling the newly introduced snd_hda_power_sync().
I had to reimplement a wheel for adding the trigger at changing the
parameter -- the parameter set ops is overwritten to pass the integer
parameter, then trigger the power-state sync.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new helper function snd_hda_power_sync() to trigger the
power-saving manually. It's an inline function call to
snd_hda_power_save() helper function.
Together with this addition, snd_hda_power_up*() and
snd_hda_power_down() functions are inlined to a call of the same
snd_hda_power_save() helper function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's possible that these amps are settable somehow, e g through
secret codec verbs, but for now, don't create the controls (as
they won't be working anyway, and cause errors in amixer).
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1038651
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize rc before returning on failure, as done elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize err before returning on failure, as done elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of blindly initializing a volume knob widget, first check
that there actually is a volume knob widget.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a simple support of automute for the front HP jack to AD1882
stack model. Such an addition is basically an exception -- we really
want to avoid the static quirk codes, but AD1882 parser isn't still
ready for moving to the BIOS auto-parser yet. So, as a quick fix, I
merged it for now.
In near future, we really need the big clean up of patch_analog.c to
move on to the auto-parser...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace with a proper ifdef check of CONFIG_PM_SLEEP in hda_intel.c.
But other places in HD-audio driver are still marked with CONFIG_PM,
since these can be called for power-saving even without
CONFIG_PM_SLEEP.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Conexant devices (e g CX20590) have no mute capability on
their Beep widgets.
This patch makes sure we don't try setting mutes on those widgets.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As spec said, 1 indicates no copyright is asserted.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The return value of snd_hda_param_read() is -1 for an error, otherwise
it's the supported power states of a codec.
The supported power states is a 32-bit value. Bit 31 will be set to 1
if the codec supports EPSS, thus making "sup" negative. And the bit
28:5 is reserved as "0".
So a negative value other than -1 shall be further checked.
Please refer to High-Definition spec 7.3.4.12 "Supported Power
States", thanks!
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When "Beep Playback Switch" had a different value on left and right
channels (such as muting left but not right, or vice versa), this
could result in the right channel being ignored.
This patch enables beep to be sounding from right channel only, and
also give correct result back to userspace (e g amixer).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function returns its own error codes instead of normal negative
error codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
