Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
This second Kselftest update for Linux 4.18-rc1:
- fixes a signedness bug in cgroups test
- adds ppc support for kprobe args tests
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPZKym/RZuOCGeA/kCwJExA0NQxwFAlshTxYACgkQCwJExA0N
Qxy4ZA//WUeH4DqnpZmFKQ7fYAzyuKGHgilRXZ3kDf7jW+VPzYtxn5/4xIJWzEKZ
76JfnZkL/zd+JgAz86UKLyUNSPEgS0W7wHW+MQgITMTdtjqaks7EW9jLpvsWBf0m
K5Wmzre7BezvpOCO4z91u7N4rsmmfzAgaGmVl2jUleXEkCBtaxQNNgfSkXzkhyua
Q2+WxVqvTcWfPTGSYtxIDNM5OiLAJ/mB+FureVuKTbFGc0aWYNIudldohNBejiLt
sGKwriaD8RMNKQCdKHZxRZoEKZGe3hpKsfxReU+KkUAtzIbmisfwiO5ohjncxp0t
OE42VMQixe2DZO3PfN58DNJeqvzPgGbILRqjRXLRL6jAS23jI5gYYicxyb0Ex8zm
+c7KEEzG4L7yAM4Z8idkKykWritjQTn02Rfwri08OvT84NtESmCadQpXsv3inIOo
6N2Ypm0+Hpe2sPocrQVQQTFO6h6xbS+pDPRR3FkZbLlcjWIAFHC9mqmP2XdvVJdq
D1vuDMfL7bHqCBQoqWcSUhPmAxiBtzEDK7TCP7txNjUguB/MGBhEPf0gailuPFMK
pJdsOY8ynnezrcA5mklKTVIAZd6hbMkdBftJRKigHRZBtZ6em+oyQcoaHhMuxUdr
LjyCDlN4HduHqxzRAx3ytbiVTcT4k12yC6+sv23YHsYZxRfpKqg=
=5i77
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull more Kselftest updates from Shuah Khan:
- fix a signedness bug in cgroups test
- add ppc support for kprobe args tests
* tag 'linux-kselftest-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kselftest/cgroup: fix a signedness bug
selftests/ftrace: Add ppc support for kprobe args tests
fix failures in the 'teardown' stage of test b7b8, probably a leftover of
commit 7c5995b33d ("tc-testing: fixed copy-pasting error in ife tests")
Fixes: a56e6bcd34 ("tc-testing: updated ife test cases")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-06-12
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Avoid an allocation warning in AF_XDP by adding __GFP_NOWARN for the
umem setup, from Björn.
2) Silence a warning in bpf fs when an application tries to open(2) a
pinned bpf obj due to missing fops. Add a dummy open fop that continues
to just bail out in such case, from Daniel.
3) Fix a BPF selftest urandom_read build issue where gcc complains that
it gets built twice, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc complains that urandom_read gets built twice.
gcc -o tools/testing/selftests/bpf/urandom_read
-static urandom_read.c -Wl,--build-id
gcc -Wall -O2 -I../../../include/uapi -I../../../lib -I../../../lib/bpf
-I../../../../include/generated -I../../../include urandom_read.c
urandom_read -lcap -lelf -lrt -lpthread -o
tools/testing/selftests/bpf/urandom_read
gcc: fatal error: input file
‘tools/testing/selftests/bpf/urandom_read’ is the
same as output file
compilation terminated.
../lib.mk:110: recipe for target
'tools/testing/selftests/bpf/urandom_read' failed
To fix this issue remove the urandom_read target and so target
TEST_CUSTOM_PROGS gets used.
Fixes: 81f77fd0de ("bpf: add selftest for stackmap with BPF_F_STACK_BUILD_ID")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull networking fixes from David Miller:
1) Fix several bpfilter/UMH bugs, in particular make the UMH build not
depend upon X86 specific Kconfig symbols. From Alexei Starovoitov.
2) Fix handling of modified context pointer in bpf verifier, from
Daniel Borkmann.
3) Kill regression in ifdown/ifup sequences for hv_netvsc driver, from
Dexuan Cui.
4) When the bonding primary member name changes, we have to re-evaluate
the bond->force_primary setting, from Xiangning Yu.
5) Eliminate possible padding beyone end of SKB in cdc_ncm driver, from
Bjørn Mork.
6) RX queue length reported for UDP sockets in procfs and socket diag
are inaccurate, from Paolo Abeni.
7) Fix br_fdb_find_port() locking, from Petr Machata.
8) Limit sk_rcvlowat values properly in TCP, from Soheil Hassas
Yeganeh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
tcp: limit sk_rcvlowat by the maximum receive buffer
net: phy: dp83822: use BMCR_ANENABLE instead of BMSR_ANEGCAPABLE for DP83620
socket: close race condition between sock_close() and sockfs_setattr()
net: bridge: Fix locking in br_fdb_find_port()
udp: fix rx queue len reported by diag and proc interface
cdc_ncm: avoid padding beyond end of skb
net/sched: act_simple: fix parsing of TCA_DEF_DATA
net: fddi: fix a possible null-ptr-deref
net: aquantia: fix unsigned numvecs comparison with less than zero
net: stmmac: fix build failure due to missing COMMON_CLK dependency
bpfilter: fix race in pipe access
bpf, xdp: fix crash in xdp_umem_unaccount_pages
xsk: Fix umem fill/completion queue mmap on 32-bit
tools/bpf: fix selftest get_cgroup_id_user
bpfilter: fix OUTPUT_FORMAT
umh: fix race condition
net: mscc: ocelot: Fix uninitialized error in ocelot_netdevice_event()
bonding: re-evaluate force_primary when the primary slave name changes
ip_tunnel: Fix name string concatenate in __ip_tunnel_create()
hv_netvsc: Fix a network regression after ifdown/ifup
...
Pull restartable sequence support from Thomas Gleixner:
"The restartable sequences syscall (finally):
After a lot of back and forth discussion and massive delays caused by
the speculative distraction of maintainers, the core set of
restartable sequences has finally reached a consensus.
It comes with the basic non disputed core implementation along with
support for arm, powerpc and x86 and a full set of selftests
It was exposed to linux-next earlier this week, so it does not fully
comply with the merge window requirements, but there is really no
point to drag it out for yet another cycle"
* 'core-rseq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq/selftests: Provide Makefile, scripts, gitignore
rseq/selftests: Provide parametrized tests
rseq/selftests: Provide basic percpu ops test
rseq/selftests: Provide basic test
rseq/selftests: Provide rseq library
selftests/lib.mk: Introduce OVERRIDE_TARGETS
powerpc: Wire up restartable sequences system call
powerpc: Add syscall detection for restartable sequences
powerpc: Add support for restartable sequences
x86: Wire up restartable sequence system call
x86: Add support for restartable sequences
arm: Wire up restartable sequences system call
arm: Add syscall detection for restartable sequences
arm: Add restartable sequences support
rseq: Introduce restartable sequences system call
uapi/headers: Provide types_32_64.h
Pull sparc updates from David Miller:
- a FPE signal fix that was also merged upstream
- privileged ADI driver from Tom Hromatka
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix compat siginfo ABI regression
selftests: sparc64: char: Selftest for privileged ADI driver
char: sparc64: Add privileged ADI driver
* DAX broke a fundamental assumption of truncate of file mapped pages.
The truncate path assumed that it is safe to disconnect a pinned page
from a file and let the filesystem reclaim the physical block. With DAX
the page is equivalent to the filesystem block. Introduce
dax_layout_busy_page() to enable filesystems to wait for pinned DAX
pages to be released. Without this wait a filesystem could allocate
blocks under active device-DMA to a new file.
* DAX arranges for the block layer to be bypassed and uses
dax_direct_access() + copy_to_iter() to satisfy read(2) calls.
However, the memcpy_mcsafe() facility is available through the pmem
block driver. In order to safely handle media errors, via the DAX
block-layer bypass, introduce copy_to_iter_mcsafe().
* Fix cache management policy relative to the ACPI NFIT Platform
Capabilities Structure to properly elide cache flushes when they are not
necessary. The table indicates whether CPU caches are power-fail
protected. Clarify that a deep flush is always performed on
REQ_{FUA,PREFLUSH} requests.
-----BEGIN PGP SIGNATURE-----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=4bfw
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This adds a user for the new 'bytes-remaining' updates to
memcpy_mcsafe() that you already received through Ingo via the
x86-dax- for-linus pull.
Not included here, but still targeting this cycle, is support for
handling memory media errors (poison) consumed via userspace dax
mappings.
Summary:
- DAX broke a fundamental assumption of truncate of file mapped
pages. The truncate path assumed that it is safe to disconnect a
pinned page from a file and let the filesystem reclaim the physical
block. With DAX the page is equivalent to the filesystem block.
Introduce dax_layout_busy_page() to enable filesystems to wait for
pinned DAX pages to be released. Without this wait a filesystem
could allocate blocks under active device-DMA to a new file.
- DAX arranges for the block layer to be bypassed and uses
dax_direct_access() + copy_to_iter() to satisfy read(2) calls.
However, the memcpy_mcsafe() facility is available through the pmem
block driver. In order to safely handle media errors, via the DAX
block-layer bypass, introduce copy_to_iter_mcsafe().
- Fix cache management policy relative to the ACPI NFIT Platform
Capabilities Structure to properly elide cache flushes when they
are not necessary. The table indicates whether CPU caches are
power-fail protected. Clarify that a deep flush is always performed
on REQ_{FUA,PREFLUSH} requests"
* tag 'libnvdimm-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (21 commits)
dax: Use dax_write_cache* helpers
libnvdimm, pmem: Do not flush power-fail protected CPU caches
libnvdimm, pmem: Unconditionally deep flush on *sync
libnvdimm, pmem: Complete REQ_FLUSH => REQ_PREFLUSH
acpi, nfit: Remove ecc_unit_size
dax: dax_insert_mapping_entry always succeeds
libnvdimm, e820: Register all pmem resources
libnvdimm: Debug probe times
linvdimm, pmem: Preserve read-only setting for pmem devices
x86, nfit_test: Add unit test for memcpy_mcsafe()
pmem: Switch to copy_to_iter_mcsafe()
dax: Report bytes remaining in dax_iomap_actor()
dax: Introduce a ->copy_to_iter dax operation
uio, lib: Fix CONFIG_ARCH_HAS_UACCESS_MCSAFE compilation
xfs, dax: introduce xfs_break_dax_layouts()
xfs: prepare xfs_break_layouts() for another layout type
xfs: prepare xfs_break_layouts() to be called with XFS_MMAPLOCK_EXCL
mm, fs, dax: handle layout changes to pinned dax mappings
mm: fix __gup_device_huge vs unmap
mm: introduce MEMORY_DEVICE_FS_DAX and CONFIG_DEV_PAGEMAP_OPS
...
* Test lookup in /proc/self/fd.
"map_files" lookup story showed that lookup is not that simple.
* Test that all those symlinks open the same file.
Check with (st_dev, st_info).
* Test that kernel threads do not have anything in their /proc/*/fd/
directory.
Now this is where things get interesting.
First, kernel threads aren't pinned by /proc/self or equivalent,
thus some "atomicity" is required.
Second, ->comm can contain whitespace and ')'.
No, they are not escaped.
Third, the only reliable way to check if process is kernel thread
appears to be field #9 in /proc/*/stat.
This field is struct task_struct::flags in decimal!
Check is done by testing PF_KTHREAD flags like we do in kernel.
PF_KTREAD value is a part of userspace ABI !!!
Other methods for determining kernel threadness are not reliable:
* RSS can be 0 if everything is swapped, even while reading
from /proc/self.
* ->total_vm CAN BE ZERO if process is finishing
munmap(NULL, whole address space);
* /proc/*/maps and similar files can be empty because unmapping
everything works. Read returning 0 can't distinguish between
kernel thread and such suicide process.
Link: http://lkml.kernel.org/r/20180505000414.GA15090@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Borkmann says:
====================
pull-request: bpf 2018-06-08
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix in the BPF verifier to reject modified ctx pointers on helper
functions, from Daniel.
2) Fix in BPF kselftests for get_cgroup_id_user() helper to only
record the cgroup id for a provided pid in order to reduce test
failures from processes interferring with the test, from Yonghong.
3) Fix a crash in AF_XDP's mem accounting when the process owning
the sock has CAP_IPC_LOCK capabilities set, from Daniel.
4) Fix an issue for AF_XDP on 32 bit machines where XDP_UMEM_PGOFF_*_RING
defines need ULL suffixes and use loff_t type as they are otherwise
truncated, from Geert.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f269099a7e ("tools/bpf: add a selftest for
bpf_get_current_cgroup_id() helper") added a test
for bpf_get_current_cgroup_id() helper. The bpf program
is attached to tracepoint syscalls/sys_enter_nanosleep
and will record the cgroup id if the tracepoint is hit.
The test program creates a cgroup and attachs itself to
this cgroup and expects that the test program process
cgroup id is the same as the cgroup_id retrieved
by the bpf program.
In a light system where no other processes called
nanosleep syscall, the test case can pass.
In a busy system where many different processes can hit
syscalls/sys_enter_nanosleep tracepoint, the cgroup id
recorded by bpf program may not match the test program
process cgroup_id.
This patch fixed an issue by communicating the test program
pid to bpf program. The bpf program only records
cgroup id if the current task pid is the same as
passed-in pid. This ensures that the recorded cgroup_id
is for the cgroup within which the test program resides.
Fixes: f269099a7e ("tools/bpf: add a selftest for bpf_get_current_cgroup_id() helper")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
"len" needs to be signed for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
As commit 28e33f9d78 ("bpf: disallow arithmetic operations on
context pointer") already describes, f1174f77b5 ("bpf/verifier:
rework value tracking") removed the specific white-listed cases
we had previously where we would allow for pointer arithmetic in
order to further generalize it, and allow e.g. context access via
modified registers. While the dereferencing of modified context
pointers had been forbidden through 28e33f9d78, syzkaller did
recently manage to trigger several KASAN splats for slab out of
bounds access and use after frees by simply passing a modified
context pointer to a helper function which would then do the bad
access since verifier allowed it in adjust_ptr_min_max_vals().
Rejecting arithmetic on ctx pointer in adjust_ptr_min_max_vals()
generally could break existing programs as there's a valid use
case in tracing in combination with passing the ctx to helpers as
bpf_probe_read(), where the register then becomes unknown at
verification time due to adding a non-constant offset to it. An
access sequence may look like the following:
offset = args->filename; /* field __data_loc filename */
bpf_probe_read(&dst, len, (char *)args + offset); // args is ctx
There are two options: i) we could special case the ctx and as
soon as we add a constant or bounded offset to it (hence ctx type
wouldn't change) we could turn the ctx into an unknown scalar, or
ii) we generalize the sanity test for ctx member access into a
small helper and assert it on the ctx register that was passed
as a function argument. Fwiw, latter is more obvious and less
complex at the same time, and one case that may potentially be
legitimate in future for ctx member access at least would be for
ctx to carry a const offset. Therefore, fix follows approach
from ii) and adds test cases to BPF kselftests.
Fixes: f1174f77b5 ("bpf/verifier: rework value tracking")
Reported-by: syzbot+3d0b2441dbb71751615e@syzkaller.appspotmail.com
Reported-by: syzbot+c8504affd4fdd0c1b626@syzkaller.appspotmail.com
Reported-by: syzbot+e5190cb881d8660fb1a3@syzkaller.appspotmail.com
Reported-by: syzbot+efae31b384d5badbd620@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support live
patching again.
- Add support for patching barrier_nospec in copy_from_user() and syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu Malaterre.
- Several series optimising various parts of the 32-bit code from Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K" ("GEFanuc,C2K"),
which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by Steve, and
a fix to our powernv cpuidle driver. Then there's a series touching mm, x86 and
fs/proc/task_mmu.c, which cleans up some details around pkey support. It was
ack'ed/reviewed by Ingo & Dave and has been in next for several weeks.
Thanks to:
Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al Viro, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Balbir Singh,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King, Dave
Hansen, Fabio Estevam, Finn Thain, Frederic Barrat, Gautham R. Shenoy, Haren
Myneni, Hari Bathini, Ingo Molnar, Jonathan Neuschäfer, Josh Poimboeuf,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu
Malaterre, Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica Gupta, Ravi
Bangoria, Russell Currey, Sam Bobroff, Samuel Mendoza-Jonas, Segher
Boessenkool, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stewart Smith,
Thiago Jung Bauermann, Torsten Duwe, Vaibhav Jain, Wei Yongjun, Wolfram Sang,
Yisheng Xie, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ZlBf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support
live patching again.
- Add support for patching barrier_nospec in copy_from_user() and
syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu
Malaterre.
- Several series optimising various parts of the 32-bit code from
Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K"
("GEFanuc,C2K"), which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by
Steve, and a fix to our powernv cpuidle driver. Then there's a series
touching mm, x86 and fs/proc/task_mmu.c, which cleans up some details
around pkey support. It was ack'ed/reviewed by Ingo & Dave and has
been in next for several weeks.
Thanks to: Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al
Viro, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd
Bergmann, Balbir Singh, Cédric Le Goater, Christophe Leroy, Christophe
Lombard, Colin Ian King, Dave Hansen, Fabio Estevam, Finn Thain,
Frederic Barrat, Gautham R. Shenoy, Haren Myneni, Hari Bathini, Ingo
Molnar, Jonathan Neuschäfer, Josh Poimboeuf, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu Malaterre,
Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica
Gupta, Ravi Bangoria, Russell Currey, Sam Bobroff, Samuel
Mendoza-Jonas, Segher Boessenkool, Shilpasri G Bhat, Simon Guo,
Souptick Joarder, Stewart Smith, Thiago Jung Bauermann, Torsten Duwe,
Vaibhav Jain, Wei Yongjun, Wolfram Sang, Yisheng Xie, YueHaibing"
* tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (251 commits)
powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
cpuidle: powernv: Fix promotion from snooze if next state disabled
powerpc: fix build failure by disabling attribute-alias warning in pci_32
ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
powerpc/pkeys: Detach execute_only key on !PROT_EXEC
powerpc/powernv: copy/paste - Mask SO bit in CR
powerpc: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove support for Marvell mv64x60 i2c controller
powerpc/boot: Remove support for Marvell MPSC serial controller
powerpc/embedded6xx: Remove C2K board support
powerpc/lib: optimise PPC32 memcmp
powerpc/lib: optimise 32 bits __clear_user()
powerpc/time: inline arch_vtime_task_switch()
powerpc/Makefile: set -mcpu=860 flag for the 8xx
powerpc: Implement csum_ipv6_magic in assembly
powerpc/32: Optimise __csum_partial()
powerpc/lib: Adjust .balign inside string functions for PPC32
...
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
triggers. For example:
# cd /sys/kernel/debug/tracing
# echo 'snapshot' > events/ftrace/print/trigger
# echo 'cause snapshot' > trace_marker
The rest of the changes are various clean ups and also one stable fix that
was added late in the cycle.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCWxftjBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qosyAQCgmhb+/HgRYIbsKa8Q70E2pMx5A/za
4rQ37Q9PhDUJlAD/aWXfrqcMm+buAU0yY4K+eb+f2feKXWXxdZ/fuh7+nA4=
=lpXM
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"One new feature was added to ftrace, which is the trace_marker now
supports triggers. For example:
# cd /sys/kernel/debug/tracing
# echo 'snapshot' > events/ftrace/print/trigger
# echo 'cause snapshot' > trace_marker
The rest of the changes are various clean ups and also one stable fix
that was added late in the cycle"
* tag 'trace-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (21 commits)
tracing: Use match_string() instead of open coding it in trace_set_options()
branch-check: fix long->int truncation when profiling branches
ring-buffer: Fix typo in comment
ring-buffer: Fix a bunch of typos in comments
tracing/selftest: Add test to test simple snapshot trigger for trace_marker
tracing/selftest: Add test to test hist trigger between kernel event and trace_marker
tracing/selftest: Add selftests to test trace_marker histogram triggers
ftrace/selftest: Fix reset_trigger() to handle triggers with filters
ftrace/selftest: Have the reset_trigger code be a bit more careful
tracing: Document trace_marker triggers
tracing: Allow histogram triggers to access ftrace internal events
tracing: Prevent further users of zero size static arrays in trace events
tracing: Have zero size length in filter logic be full string
tracing: Add trigger file for trace_markers tracefs/ftrace/print
tracing: Do not show filter file for ftrace internal events
tracing: Add brackets in ftrace event dynamic arrays
tracing: Have event_trace_init() called by trace_init_tracefs()
tracing: Add __find_event_file() to find event files without restrictions
tracing: Do not reference event data in post call triggers
tracepoints: Fix the descriptions of tracepoint_probe_register{_prio}
...
This Kselftest update for 4.18-rc1 consists of:
- Work to restructure timers test suite to move PIE out of rtctest from
Alexandre Belloni.
- Several minor spelling and bug fixes.
- New cgroup tests from Roman Gushchin and Mike Rapoport.
- Kselftest framework changes to handle and report skipped tests correctly.
Prior to these changes, framework treated all non-zero return codes from
tests as failures. When tests are skipped with non-zero return code, due
to unmet dependencies and/or unsupported configuration, reporting them as
failed lead to false negatives on the tests that couldn't be run.
- Fixes to test Makefiles to remove unnecessary RUN_TESTS and EMIT_TESTS
overrides and use common defines from lib.mk.
- Fixes to several tests to return correct Kselftest skip code.
- Changes to improve test output.
-----BEGIN PGP SIGNATURE-----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=eVzz
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest update from Shuah Khan:
- Work to restructure timers test suite to move PIE out of rtctest from
Alexandre Belloni.
- Several minor spelling and bug fixes.
- New cgroup tests from Roman Gushchin and Mike Rapoport.
- Kselftest framework changes to handle and report skipped tests
correctly.
Prior to these changes, framework treated all non-zero return codes
from tests as failures. When tests are skipped with non-zero return
code, due to unmet dependencies and/or unsupported configuration,
reporting them as failed lead to false negatives on the tests that
couldn't be run.
- Fixes to test Makefiles to remove unnecessary RUN_TESTS and
EMIT_TESTS overrides and use common defines from lib.mk.
- Fixes to several tests to return correct Kselftest skip code.
- Changes to improve test output.
* tag 'linux-kselftest-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (55 commits)
selftests: lib: fix prime_numbers module search and skip logic
selftests: intel_pstate: notification about privilege required to run intel_pstate testing script
selftests: cgroup/memcontrol: add basic test for socket accounting
selftest: intel_pstate: debug support message from aperf.c and return value
kselftest/cgroup: fix variable dereferenced before check warning
selftests/intel_pstate: Enhance table printing
selftests/intel_pstate: Improve test, minor fixes
selftests: cgroup/memcontrol: add basic test for swap controls
selftests: cgroup: add memory controller self-tests
selftests: memfd: split regular and hugetlbfs tests
selftests: net: return Kselftest Skip code for skipped tests
selftests: mqueue: return Kselftest Skip code for skipped tests
selftests: memory-hotplug: return Kselftest Skip code for skipped tests
selftests: memfd: return Kselftest Skip code for skipped tests
selftests: membarrier: return Kselftest Skip code for skipped tests
selftests: media_tests: return Kselftest Skip code for skipped tests
selftests: locking: return Kselftest Skip code for skipped tests
selftests: locking: add Makefile for locking test
selftests: lib: return Kselftest Skip code for skipped tests
selftests: lib: add prime_numbers.sh test to Makefile
...
"param_test" is a parametrizable restartable sequences test. See
the "--help" output for usage.
"param_test_benchmark" is the same as "param_test", but it removes
testing book-keeping code to allow accurate benchmarks.
"param_test_compare_twice" is the same as "param_test", but it performs
each comparison within rseq critical section twice, thus validating
invariants. If any of the second comparisons fails, an error message
is printed and the test aborts.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: linux-kselftest@vger.kernel.org
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Hunter <ahh@google.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: linux-api@vger.kernel.org
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180602124408.8430-16-mathieu.desnoyers@efficios.com
"basic_percpu_ops_test" is a slightly more "realistic" variant,
implementing a few simple per-cpu operations and testing their
correctness.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: linux-kselftest@vger.kernel.org
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Hunter <ahh@google.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: linux-api@vger.kernel.org
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180602124408.8430-15-mathieu.desnoyers@efficios.com
This rseq helper library provides a user-space API to the rseq()
system call.
The rseq fast-path exposes the instruction pointer addresses where the
rseq assembly blocks begin and end, as well as the associated abort
instruction pointer, in the __rseq_table section. This section allows
debuggers may know where to place breakpoints when single-stepping
through assembly blocks which may be aborted at any point by the kernel.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: linux-kselftest@vger.kernel.org
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Hunter <ahh@google.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: linux-api@vger.kernel.org
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180602124408.8430-13-mathieu.desnoyers@efficios.com
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-06-05
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a new BPF hook for sendmsg similar to existing hooks for bind and
connect: "This allows to override source IP (including the case when it's
set via cmsg(3)) and destination IP:port for unconnected UDP (slow path).
TCP and connected UDP (fast path) are not affected. This makes UDP support
complete, that is, connected UDP is handled by connect hooks, unconnected
by sendmsg ones.", from Andrey.
2) Rework of the AF_XDP API to allow extending it in future for type writer
model if necessary. In this mode a memory window is passed to hardware
and multiple frames might be filled into that window instead of just one
that is the case in the current fixed frame-size model. With the new
changes made this can be supported without having to add a new descriptor
format. Also, core bits for the zero-copy support for AF_XDP have been
merged as agreed upon, where i40e bits will be routed via Jeff later on.
Various improvements to documentation and sample programs included as
well, all from Björn and Magnus.
3) Given BPF's flexibility, a new program type has been added to implement
infrared decoders. Quote: "The kernel IR decoders support the most
widely used IR protocols, but there are many protocols which are not
supported. [...] There is a 'long tail' of unsupported IR protocols,
for which lircd is need to decode the IR. IR encoding is done in such
a way that some simple circuit can decode it; therefore, BPF is ideal.
[...] user-space can define a decoder in BPF, attach it to the rc
device through the lirc chardev.", from Sean.
4) Several improvements and fixes to BPF core, among others, dumping map
and prog IDs into fdinfo which is a straight forward way to correlate
BPF objects used by applications, removing an indirect call and therefore
retpoline in all map lookup/update/delete calls by invoking the callback
directly for 64 bit archs, adding a new bpf_skb_cgroup_id() BPF helper
for tc BPF programs to have an efficient way of looking up cgroup v2 id
for policy or other use cases. Fixes to make sure we zero tunnel/xfrm
state that hasn't been filled, to allow context access wrt pt_regs in
32 bit archs for tracing, and last but not least various test cases
for fixes that landed in bpf earlier, from Daniel.
5) Get rid of the ndo_xdp_flush API and extend the ndo_xdp_xmit with
a XDP_XMIT_FLUSH flag instead which allows to avoid one indirect
call as flushing is now merged directly into ndo_xdp_xmit(), from Jesper.
6) Add a new bpf_get_current_cgroup_id() helper that can be used in
tracing to retrieve the cgroup id from the current process in order
to allow for e.g. aggregation of container-level events, from Yonghong.
7) Two follow-up fixes for BTF to reject invalid input values and
related to that also two test cases for BPF kselftests, from Martin.
8) Various API improvements to the bpf_fib_lookup() helper, that is,
dropping MPLS bits which are not fully hashed out yet, rejecting
invalid helper flags, returning error for unsupported address
families as well as renaming flowlabel to flowinfo, from David.
9) Various fixes and improvements to sockmap BPF kselftests in particular
in proper error detection and data verification, from Prashant.
10) Two arm32 BPF JIT improvements. One is to fix imm range check with
regards to whether immediate fits into 24 bits, and a naming cleanup
to get functions related to rsh handling consistent to those handling
lsh, from Wang.
11) Two compile warning fixes in BPF, one for BTF and a false positive
to silent gcc in stack_map_get_build_id_offset(), from Arnd.
12) Add missing seg6.h header into tools include infrastructure in order
to fix compilation of BPF kselftests, from Mathieu.
13) Several formatting cleanups in the BPF UAPI helper description that
also fix an error during rst2man compilation, from Quentin.
14) Hide an unused variable in sk_msg_convert_ctx_access() when IPv6 is
not built into the kernel, from Yue.
15) Remove a useless double assignment in dev_map_enqueue(), from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull RCU updates from Ingo Molnar:
- updates to the handling of expedited grace periods
- updates to reduce lock contention in the rcu_node combining tree
[ These are in preparation for the consolidation of RCU-bh,
RCU-preempt, and RCU-sched into a single flavor, which was
requested by Linus in response to a security flaw whose root cause
included confusion between the multiple flavors of RCU ]
- torture-test updates that save their users some time and effort
- miscellaneous fixes
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
rcu/x86: Provide early rcu_cpu_starting() callback
torture: Make kvm-find-errors.sh find build warnings
rcutorture: Abbreviate kvm.sh summary lines
rcutorture: Print end-of-test state in kvm.sh summary
rcutorture: Print end-of-test state
torture: Fold parse-torture.sh into parse-console.sh
torture: Add a script to edit output from failed runs
rcu: Update list of rcu_future_grace_period() trace events
rcu: Drop early GP request check from rcu_gp_kthread()
rcu: Simplify and inline cpu_needs_another_gp()
rcu: The rcu_gp_cleanup() function does not need cpu_needs_another_gp()
rcu: Make rcu_start_this_gp() check for out-of-range requests
rcu: Add funnel locking to rcu_start_this_gp()
rcu: Make rcu_start_future_gp() caller select grace period
rcu: Inline rcu_start_gp_advanced() into rcu_start_future_gp()
rcu: Clear request other than RCU_GP_FLAG_INIT at GP end
rcu: Cleanup, don't put ->completed into an int
rcu: Switch __rcu_process_callbacks() to rcu_accelerate_cbs()
rcu: Avoid __call_rcu_core() root rcu_node ->lock acquisition
rcu: Make rcu_migrate_callbacks wake GP kthread when needed
...
Several complex trigger tests were added for trace_marker, but not a simple
one. This could be used to help diagnose a problem with the code by giving a
reference between how complex a trigger is that fails.
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The test description is displayed with the PASS/FAIL resolution after
the test is ran. There however already is one other test described
exactly like this, which makes it unclear which of the tests passed or
failed. Make the description unique.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of installing a trap before tests run and uninstalling it after
they run, mirror_vlan.sh installs it twice due to a typo. Fix the typo.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add regression tests for PF_PACKET transmission using packet_snd.
The TPACKET ring interface has tests for transmission and reception.
This is an initial stab at the same for the send call based interface.
Packets are sent over loopback, then read twice. The entire packet is
read from another packet socket and compared. The packet is also
verified to arrive at a UDP socket for protocol conformance.
The test sends a packet over loopback, testing the following options
(not the full cross-product):
- SOCK_DGRAM
- SOCK_RAW
- vlan tag
- qdisc bypass
- bind() and sendto()
- virtio_net_hdr
- csum offload (NOT actual csum feature, ignored on loopback)
- gso
Besides these basic functionality tests, the test runs from a set
of bounds checks, positive and negative. Running over loopback, which
has dev->min_header_len, it cannot generate variable length hhlen.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that udpgso can generate segments smaller than device mtu, down
to the extreme case of 1B gso_size.
Verify that irrespective of gso_size, udpgso restricts the number of
segments it will generate per call (UDP_MAX_SEGMENTS).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing msg_zerocopy test takes additional protocol arguments.
Add a variant that takes no arguments and runs all supported variants.
Call this from kselftest.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syscall name_to_handle_at() can be used to get cgroup id
for a particular cgroup path in user space. The selftest
got cgroup id from both user and kernel, and compare to
ensure they are equal to each other.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add several test cases where the same or different map pointers
originate from different paths in the program and execute a map
lookup or tail call at a common location.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This tests perf hardware breakpoints (ie PERF_TYPE_BREAKPOINT) on
powerpc.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The t->type in BTF_KIND_FWD is not used. It must be 0.
This patch ensures that and also adds a test case in test_btf.c
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch ensures array's t->size is 0.
The array size is decided by its individual elem's size and the
number of elements. Hence, t->size is not used and
it must be 0.
A test case is added to test_btf.c
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Print values of test options like apply, cork, start, end so that
individual failed tests can be identified for manual run
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When data verification is enabled, some tests fail because verification is done
incorrectly. Following changes fix it.
- Identify the size of data block to be verified
- Reset verification counter when data block size is reached
- Fixed the value printed in case of verfication failure
Fixes: 16962b2404 ("bpf: sockmap, add selftests")
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently 10us delay is too low for many tests to succeed. It needs to
be increased. Also, many corked tests are expected to hit rx timeout
irrespective of timeout value.
- This patch sets 1000usec timeout value for corked tests because less
than that causes broken-pipe error in tx thread. Also sets 1 second
timeout for all other tests because less than that results in RX
timeout
- tests with apply=1 and higher number of iterations were taking lot
of time. This patch reduces test run time by reducing iterations.
real 0m12.968s
user 0m0.219s
sys 0m14.337s
Fixes: a18fda1a62 ("bpf: reduce runtime of test_sockmap tests")
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In case of selftest mode, temporary cgroup environment is created but
cgroup is not joined. It causes test failures. Fixed by joining the
cgroup
Fixes: 16962b2404 ("bpf: sockmap, add selftests")
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Test failures are not identified because exit code of RX/TX threads
is not checked. Also threads are not returning correct exit code.
- Return exit code from threads depending on test execution status
- In main thread, check the exit code of RX/TX threads
- Skip error checking for corked tests as they are expected to timeout
Fixes: 16962b2404 ("bpf: sockmap, add selftests")
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
To test offloading of mirror-to-gretap in mlxsw for cases that a
VLAN-unaware bridge is in underlay packet path, test that the STP status
of bridge egress port is reflected.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloading of mirror-to-gretap in mlxsw is tricky especially in cases
when the gretap underlay involves bridges. Add more tests that exercise
the bridge handling code:
- forbidden_egress tests that check vlan removal on bridge port in the
underlay packet path
- untagged_egress tests that similarly check "egress untagged"
- fdb_roaming tests that check whether learning FDB on a different port
is reflected
- stp tests for handling port STP status of bridge egress port
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename test_gretap_forbidden() and test_ip6gretap_forbidden() to a more
specific test_gretap_forbidden_cpu() and test_ip6gretap_forbidden_cpu().
This will make it clearer which is which when further down a patch is
introduced that forbids a VLAN on regular bridge port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds