Until RPI 3 and Zero W the pl011 (uart0) was always on pin 14/15. So in
order to take care of them and other boards in the future,
we need to define UART pinmuxing on board level.
This work based on Eric Anholt's patch "ARM: bcm2385: Don't force pl011
onto pins 14/15." and Fabian Vogt's patch "ARM64: dts: bcm2837: assign
uart0 to BT and uart1 to pin headers".
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
sdcard access with the sdhost controller is faster.
Read access (dd with 64k blocks on rpi2):
CONFIG_MMC_SDHCI_IPROC: 11-12 MB/s
CONFIG_MMC_BCM2835: 19-20 MB/s
Differences on write access are pretty much in the noise.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Eric Anholt <eric@anholt.net>
The modules stay disabled by default, and if you want to enable DSI
you'll need an overlay that connects a panel to it.
Signed-off-by: Eric Anholt <eric@anholt.net>
Enable the VEC IP on all RaspberryPi boards.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As the alt3 group has no pins left drop it from &gpio.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
This file is included from DTS files under arch/arm64 too (via
broadcom/bcm2837-rpi-3-b.dts and broadcom/bcm2837.dtsi). There is a desire
not to have skeleton.dtsi for ARM64. See commit 3ebee5a2e1 ("arm64: dts:
kill skeleton.dtsi") for rationale for its removal.
As well as the addition of #*-cells also requires adding the device_type to
the rpi memory node explicitly.
Note that this change results in the removal of an empty /aliases node from
bcm2835-rpi-a.dtb and bcm2835-rpi-a-plus.dtb. I have no hardware to check
if this is a problem or not.
It also results in some reordering of the nodes in the DTBs (the /aliases
and /memory nodes come later). This isn't supposed to matter but, again,
I've no hardware to check if it is true in this particular case.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: arm@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This connects the USB driver to the USB power domain, so that USB can
actually be turned on at boot if the bootloader didn't do it for us.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
For Raspberry Pi 2, we want to use the same general pin assignment
bits, but need to use bcm2836.dtsi for the CPU instead.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch converts all bcm2835 dts and dtsi files to use the pinctrl
header file.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The model B and B+ differ in the GPIO lines for ACT and PWR leds, and the
I2S interface.
Signed-off-by: Matthias Klein <matthias.klein@linux.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
