Remove the leading zero from unit address to fix the following build
warning with W=1:
arch/arm/boot/dts/imx6dl-hummingboard2.dtb: Warning (unit_address_format): Node /soc/aips-bus@2100000/i2c@21a0000/codec@0a unit name should not have leading 0s
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make the regulators match the schematic - name the regulators after
one of their schematic supply names, and arrange them into their
heirarchy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
eMMC is optional on HB2 boards, and may be implemented by the SOM. Move
it out of the base HB2 include file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Name the regulators according to the voltage rails they are feeding in
the schematic. The USB 2-4 regulators are fixed regulators and are always
on, as they are not a VBUS supply for a single USB host port on the i.MX6,
but supply VBUS to ports behind a USB hub and there is currently no way
to model this in mainline.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PWM nodes are already disabled in the imx6qdl.dtsi, so there
is no need to disable them again in the board DTS.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver always uses active-low, but better describe reality in the DT.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It's disabled by default and the data mapping is supposed to be
retrieved from the attached panel driver in mainline.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VDDD is supplied by VCC_1P8 on HB2.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use proper gpio flag definitions for GPIOs rather than using opaque
uninformative numbers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the SD card detect signal, which was missing the polarity
specification, and the pull-up necessary for proper signalling.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the microsom includes into the .dts files.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename microsom include to imx6qdl-sr-som.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the AR8035 include, the file is now gone.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for the Hummingboard Gate and Edge devices from
SolidRun.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
