sound/soc/soc-core.c: In function ‘snd_soc_put_volsw_sx’:
sound/soc/soc-core.c:2600: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some codecs namely Cirrus Logic Codecs have a way of wrapping the dB scale around 0dB without 0dB being in the middle.
Rework of SOC_DOUBLE_R_SX_TLV to be more consistent with other asoc tlv macros.
Add single register macro : SOC_SINGLE_SX_TLV.
Use snd_soc_info_volsw for .info
Use snd_soc_get_volsw_sx, snd_soc_put_volsw_sx for single and double.
kcontrols for CS42L51 and CS42L73 are adjusted to these new TLV Macros.
The max value is determined by: (number of steps) +1 for 0dB +max from codec datasheet.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In version 3.4 the driver core acquired probe deferral which is a core way
of doing essentially the same thing as ASoC has been doing since forever
to make sure that all the devices needed to make up the card are present
without needing open coding in the subsystem.
Make basic use of this probe deferral mechanism for the cards, removing the
need to handle partially instantiated cards. We should be able to remove
even more code than this, though some of the checks we're currently doing
should stay since they're about things like suppressing unneeded DAPM runs
rather than deferring probes.
In order to avoid robustness issues with our teardown paths (which do need
quite a bit of TLC) add a check for aux_devs prior to attempting to set
things up, this means that we've got a reasonable idea that everything will
be there before we start. As with the removal of partial instantiation
support more work will be needed to make this work neatly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently stream events are only perfomed on codec stream widgets only.
There is now a need to be able to perform stream events on platform
widgets too.
e.g. we have the ABE platform driver with several DAI links
to dummy codecs. We need to be able to perform stream events on any
of the dummy codec DAI links.
This patch also removes the snd_soc_dai * parameter since it's already
contained within the rtd * parameter.
Finally makle stream event return void since no one checks it anyway.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add platform driver support for CPU DAI DAPM widgets.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has now become necessary to use a DAPM mutex instead of the codec
mutex to lock the DAPM operations. This is due to the recent multi
component support and forth coming Dynamic PCM updates.
Currently we lock DAPM operations with the codec mutex of the calling
RTD context. However, DAPM operations can span the whole card context
and all components.
This patch updates the DAPM operations that use the codec mutex to
now use the DAPM mutex PCM subclass for all DAPM ops.
We also add a mutex subclass for DAPM init and PCM operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the first part of a change that is intended to improve
ASoC locking protection for DAPM and PCM operations.
This part of the series adds a mutex class for the soc_card mutex. The
SND_SOC_CARD_CLASS_INIT class is used for card initialisation only whilst the
SND_SOC_CARD_CLASS_PCM class is used for the forth coming Dynamic
PCM operations. The new mutex classes are required otherwise we will see a false
positive mutex deadlock warning between the card initialisation and the PCM
operations (something that would never deadlock in real life).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're currently not freeing card->rtd in cases where the card is
unregistered before being instantiated - convert it to devm_kzalloc() to
make sure that happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Not having a DAI link set_fmt operation is perfectly normal and
should not be complaint.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add mutex support for platform IO operations. e.g. can be used
for platform DAPM widget IO ops.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_register_card() has been available and strongly preferred since
2.6.38 but we're still seeing new drivers using it and the conversion rate
for older machines has been low. Help address both issues by logging a
warning when the soc-audio device probes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Make sure we cleanup the platform debugfs when probe fails.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SET_SYSTEM_SLEEP_PM_OPS writes .poweroff = *_resume once. Then we overwrite it
again explicitly as .poweroff = snd_soc_poweroff. Even though it works, as the
second one overwrites the first one, this is not the correct way. Fix this by
expanding SET_SYSTEM_SLEEP_PM_OPS in our structure.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Chip designers frequently include things like the enable and disable
controls for algorithms in the register blocks which also hold the
coefficients. Since it's desirable to split out the enable/disable
control from userspace the plain SND_SOC_BYTES() isn't optimal for
these devices.
Add a SND_SOC_BYTES_MASK() which allows a bitmask from the first word
of the block to be excluded from the control. This supports the needs
of devices I've looked at and lets us have a reasonably simple API.
Further controls can be added in future if that's needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow devices to export blocks of registers to the application layer,
intended for use for reading and writing coefficient data which can't
usefully be worked with by the kernel at runtime (for example, due to
requiring complex and expensive calculations or being the results of
callibration procedures). Currently drivers are using platform data to
provide configurations for coefficient blocks which isn't at all
convenient for runtime management or configuration development.
Currently only devices using regmap are supported, an error will be
generated for any attempt to work with a byte control on a non-regmap
device. There's no fundamental block to other devices so support could
be added if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Showing the returned values on error messages is useful information.
While at it, use pr_err/pr_warn whenever possible.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to allow us to do smarter things with DAI links create DAPM
widgets which directly represent the DAIs in the DAPM graph. These are
automatically created from the DAIs as we probe the card with references
held in both directions between the widget and the DAI.
The widgets are not made available for direct instantiation by drivers,
they are created automatically from the DAIs. Drivers should be updated
to create stream routes using DAPM maps rather than by annotating AIF
and DAC widgets with streams.
In order to ease transition to this model from existing drivers we
automatically create DAPM routes between the DAI widgets and the existing
stream widgets which are started and stopped by the DAI widgets, though
the old stream handling mechanism is still in place. This also has the
nice effect of removing non-DAPM devices as any device with a DAI
acquires a widget automatically which will allow future simplifications
to the core DAPM logic.
The intention is that in future the AIF and DAI widgets will gain the
ability to interact such that we are able to manage activity on
individual channels independantly rather than powering up and down the
entire AIF as we do currently.
Currently we only generate these for CODECs, mostly as I have no systems
with non-CODEC DAPM to integrate with. It should be a simple matter of
programming to add the additional hookup for these.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Neater and avoids warnings when used in other places where const strings
are desired.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow us to do something smarter than iterate through widgets
doing strcmp() to work out what to power up for stream events change the
interface used to generate them to be based on the combination of a DAI
and a stream direction rather than just a simple string identifying the
stream.
At some point we'll probably want a set of channels too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow platform widgets to be visible in debugfs like codec widgets.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the codec debugfs initialisation to use dev_warn() instead of
printk(KERN_WARNING).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. the number of the half-beast?
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPMzv8AAoJEHm+PkMAQRiGgeYIAJxxGCxSMLRIiPaGRmQbWifs
eE3z6AUWitGfYvhmYdWVz+C/aa4pPCVWr3bAFxUQhu+ESmiFIiqiefvlTRf5f84e
pcoJFobkFfhtK4gLvUr75WxXDFq/1HhKqW1OLzIW4gQsnhMdjGJ3lLK6ZoRYH8h4
cGoN3DRII9mVLFcB2sgbeRvbQBA/O4n0aOQ2ryZkCcPQQMIKhR/rUEEV2pe/ovHE
rumQgI3PVey816P4e5YnOvrEAllFZlaZ/F0ClJgNdfeQCVTZx9KNRbiNxHi6fcC5
6Zgg7e5EvQTAy7QqQZ0hmS4k4CFmnswX3Nm+ZabRNqBdLSjPEDD9hk1o1dodYCg=
=BBLC
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc3' as we've got several bugfixes in there which are
colliding annoyingly with development.
Linux 3.3-rc3
.. the number of the half-beast?
Conflicts:
sound/soc/codecs/wm5100.c
sound/soc/codecs/wm8994.c
This is usually not a use case dependant flag anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the same pm_ops for all system suspend and resume paths. This isn't
ideal for suspend to disk with older CODECs as we'll suspend and then
resume the CODEC before powering off all of which takes a long time due
to VMID ramps but it's very simple to implement and for modern CODECs the
overhead should be minimal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If an idle_bias_off device is in any state other than off then it is still
active for some reason (typically a low power function such as accessory
detection). This wasn't an issue when the feature was implemented as we
always went to _ON for any active function, subsequent power improvements
have changed things.
With the modern way of doing things we should overhaul the infrastructure
to allow devices to explicitly take references for these functions but
that's a much more invasive change and will require driver updates to
deploy, this will bring the framework into line with the existing driver
set before we do that work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Print out the offending DAI link entry when a naming error occurs. Makes
thing easier to debug for machines with a large number of DAI links.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix platform removal by freeing the platform DAPM resources and remove
it from the DAPM list.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device model needs a release() function so it can free devices when
they become dereferenced. Do that for rtds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that everything is seeing the same declaration by moving it to
a header file rather than putting the declaration in soc-core.c
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
DAI link endpoints and platform (DMA) devices are currently specified
by name. When instantiating sound cards from device tree, it may be more
convenient to refer to these devices by phandle in the device tree, and
for code to describe DAI links using the "struct device_node *"
("of_node") those phandles map to.
This change adds new fields to snd_soc_dai_link which can "name" devices
using of_node, enhances soc_bind_dai_link() to allow binding based on
of_node, and enhances snd_soc_register_card() to ensure that illegal
combinations of name and of_node are not used.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement snd_soc_of_parse_audio_routing(), a utility function that can
parses a simple DAPM route table from device tree.The machine driver
specifies the DT property to use, since this is binding-specific.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement snd_soc_of_parse_card_name(), a utility function that sets a
card's name from device tree. The machine driver specifies the DT
property to use, since this is binding-specific.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The message was obviously copied from soc_init_codec_debugfs()
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Transform some loops from:
for_each(x) {
if (f(x)) {
work_on(x);
}
}
to new structure:
for_each(x) {
if (!f(x))
continue;
work_on(x);
}
This will allow future modification of f(x) with less impact to the code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to enumerate all the CODECs that are part of the card we're
instantiating, not all the CODECs that are in the system as the system
may have multiple cards.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A card is fully routed if the DAPM route table describes all connections on
the board.
When a card is fully routed, some operations can be automated by the ASoC
core. The first, and currently only, such operation is described below, and
implemented by this patch.
Codecs often have a large number of external pins, and not all of these pins
will be connected on all board designs. Some machine drivers therefore call
snd_soc_dapm_nc_pin() for all the unused pins, in order to tell the ASoC core
never to activate them.
However, when a card is fully routed, the information needed to derive the
set of unused pins is present in card->dapm_routes. In this case, have
the ASoC core automatically call snd_soc_dapm_nc_pin() for each unused
codec pin.
This has been tested with soc/tegra/tegra_wm8903.c and soc/tegra/trimslice.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are cases where there is no working codec on the soc-audio devices,
and snd_soc_suspend() will skip such device when suspending. Yet its
counterpart snd_soc_resume() does not check this, causing complaints
about spinlock lockup:
[ 176.726087] BUG: spinlock lockup on CPU#0, kworker/0:2/1067, d8ab82a8
[ 176.732539] [<80014a14>] (unwind_backtrace+0x0/0xec) from [<805b3fc8>] (dump_stack+0x20/0x24)
[ 176.741082] [<805b3fc8>] (dump_stack+0x20/0x24) from [<80322208>] (do_raw_spin_lock+0x118/0x158)
[ 176.749882] [<80322208>] (do_raw_spin_lock+0x118/0x158) from [<805b7874>] (_raw_spin_lock_irqsave+0x5c/0x68)
[ 176.759723] [<805b7874>] (_raw_spin_lock_irqsave+0x5c/0x68) from [<8002a020>] (__wake_up+0x2c/0x5c)
[ 176.768781] [<8002a020>] (__wake_up+0x2c/0x5c) from [<804a6de8>] (soc_resume_deferred+0x3c/0x2b0)
[ 176.777666] [<804a6de8>] (soc_resume_deferred+0x3c/0x2b0) from [<8004ee20>] (process_one_work+0x2e8/0x50c)
[ 176.787334] [<8004ee20>] (process_one_work+0x2e8/0x50c) from [<8004fd08>] (worker_thread+0x1c8/0x2e0)
[ 176.796566] [<8004fd08>] (worker_thread+0x1c8/0x2e0) from [<80053ec8>] (kthread+0xa4/0xb0)
[ 176.804843] [<80053ec8>] (kthread+0xa4/0xb0) from [<8000ea70>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't want to clear the prefix while we're creating the DAPM controls
for the device as the prefix is applied during control creation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Ensure we only have one sync during the initial startup of the card by
making snd_soc_dapm_sync() a noop on non-instantiated cards. This avoids
any bounces due to things like jacks reporting their initial state on
partially initialised cards. The callers that don't also get called at
runtime should just be removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the put_volsw/put_volsw_2r in one function.
To avoid build breakage in twl6040 keep the
snd_soc_put_volsw_2r as define, and map it snd_soc_put_volsw.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the get_volsw/get_volsw_2r in one function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the info_volsw/info_volsw_2r in one function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to reduce the number of DAPM power checks we run keep a list of
widgets which have been changed since the last DAPM run and iterate over
that rather than the full widget list. Whenever we change the power state
for a widget we add all the source and sink widgets it has to the dirty
list, ensuring that all widgets in the path are checked.
This covers more widgets than we need to as some of the neighbour widgets
won't be connected but it's simpler as a first step. On one system I tried
this gave:
Power Path Neighbour
Before: 207 1939 2461
After: 114 1066 1327
which seems useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Brian Austin