When rdst of an offloaded FDB entry is replaced, it certainly isn't
offloaded anymore. Drivers are notified about such replacements, and can
re-mark the entry as offloaded again if they so wish. However until a
driver does so explicitly, assume a replaced FDB entry is not offloaded.
Note that replaces coming via vxlan_fdb_external_learn_add() are always
immediately followed by an explicit offload marking.
Fixes: 0efe117333 ("vxlan: Support marking RDSTs as offloaded")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anssi Hannula says:
====================
net: macb: DMA race condition fixes
Here are a couple of race condition fixes for the macb driver. The first
two are for issues observed at runtime on real HW.
v2:
- added received Tested-bys and Acked-bys to the first two patches
- in patch 3/3, moved the timestamp protection barrier closer to the
timestamp reads
- in patch 3/3, removed unnecessary move of the addr assignment in
gem_rx() to keep the patch minimal for maximum clarity
- in patch 3/3, clarified commit message and comments
The 3/3 is the same one I improperly sent last week as a standalone
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.
The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.
A message is logged when the above scenario occurs:
macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor
Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.
This issue was observed on a ZynqMP based system.
Fixes: 4df95131ea ("net/macb: change RX path for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.
The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.
Fix that by adding the necessary DMA memory barrier between the writes.
This corruption was observed on a ZynqMP based system.
Fixes: fff8019a08 ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: Harini Katakam <harini.katakam@xilinx.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herton reports the following error when building a userspace program that
includes net_stamp.h:
In file included from foo.c:2:
/usr/include/linux/net_tstamp.h:158:2: error: unknown type name
‘clockid_t’
clockid_t clockid; /* reference clockid */
^~~~~~~~~
Fix it by using __kernel_clockid_t in place of clockid_t.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Cc: Timothy Redaelli <tredaelli@redhat.com>
Reported-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms (currently detected only on SAMA5D4) TX might stuck
even the pachets are still present in DMA memories and TX start was
issued for them. This happens due to race condition between MACB driver
updating next TX buffer descriptor to be used and IP reading the same
descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted.
GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt
is asserted TX must be restarted. Restart TX if used bit is read and
packets are present in software TX queue. Packets are removed from software
TX queue if TX was successful for them (see macb_tx_interrupt()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function should return an error if create_singlethread_workqueue()
fails.
Fixes: 34877a15f7 ("net: stmmac: Rework and fix TX Timeout code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 143ece654f ("tipc: check tsk->group in tipc_wait_for_cond()")
we have to reload grp->dests too after we re-take the sock lock.
This means we need to move the dsts check after tipc_wait_for_cond()
too.
Fixes: 75da2163db ("tipc: introduce communication groups")
Reported-and-tested-by: syzbot+99f20222fc5018d2b97a@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.
Fixes: d2201a2159 ("qed: No need for LL2 frags indication")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() function sets all modes that are
supported by a given PPv2 port. A recent change made all ports to
advertise they support 10G modes in certain cases. This is not true,
as only the port #0 can do so. This patch fixes it.
Fixes: 01b3fd5ac9 ("net: mvpp2: fix detection of 10G SFP modules")
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some guests OSes (including Windows 10) write to MSR 0xc001102c
on some cases (possibly while trying to apply a CPU errata).
Make KVM ignore reads and writes to that MSR, so the guest won't
crash.
The MSR is documented as "Execution Unit Configuration (EX_CFG)",
at AMD's "BIOS and Kernel Developer's Guide (BKDG) for AMD Family
15h Models 00h-0Fh Processors".
Cc: stable@vger.kernel.org
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by syzkaller:
CPU: 1 PID: 5962 Comm: syz-executor118 Not tainted 4.20.0-rc6+ #374
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:kvm_apic_hw_enabled arch/x86/kvm/lapic.h:169 [inline]
RIP: 0010:vcpu_scan_ioapic arch/x86/kvm/x86.c:7449 [inline]
RIP: 0010:vcpu_enter_guest arch/x86/kvm/x86.c:7602 [inline]
RIP: 0010:vcpu_run arch/x86/kvm/x86.c:7874 [inline]
RIP: 0010:kvm_arch_vcpu_ioctl_run+0x5296/0x7320 arch/x86/kvm/x86.c:8074
Call Trace:
kvm_vcpu_ioctl+0x5c8/0x1150 arch/x86/kvm/../../../virt/kvm/kvm_main.c:2596
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x1de/0x1790 fs/ioctl.c:696
ksys_ioctl+0xa9/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The reason is that the testcase writes hyperv synic HV_X64_MSR_SINT14 msr
and triggers scan ioapic logic to load synic vectors into EOI exit bitmap.
However, irqchip is not initialized by this simple testcase, ioapic/apic
objects should not be accessed.
This patch fixes it by also considering whether or not apic is present.
Reported-by: syzbot+39810e6c400efadfef71@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
nested_get_vmcs12_pages() processes the posted_intr address in vmcs12. It
caches the kmap()ed page object and pointer, however, it doesn't handle
errors correctly: it's possible to cache a valid pointer, then release
the page and later dereference the dangling pointer.
I was able to reproduce with the following steps:
1. Call vmlaunch with valid posted_intr_desc_addr but an invalid
MSR_EFER. This causes nested_get_vmcs12_pages() to cache the kmap()ed
pi_desc_page and pi_desc. Later the invalid EFER value fails
check_vmentry_postreqs() which fails the first vmlaunch.
2. Call vmlanuch with a valid EFER but an invalid posted_intr_desc_addr
(I set it to 2G - 0x80). The second time we call nested_get_vmcs12_pages
pi_desc_page is unmapped and released and pi_desc_page is set to NULL
(the "shouldn't happen" clause). Due to the invalid
posted_intr_desc_addr, kvm_vcpu_gpa_to_page() fails and
nested_get_vmcs12_pages() returns. It doesn't return an error value so
vmlaunch proceeds. Note that at this time we have a dangling pointer in
vmx->nested.pi_desc and POSTED_INTR_DESC_ADDR in L0's vmcs.
3. Issue an IPI in L2 guest code. This triggers a call to
vmx_complete_nested_posted_interrupt() and pi_test_and_clear_on() which
dereferences the dangling pointer.
Vulnerable code requires nested and enable_apicv variables to be set to
true. The host CPU must also support posted interrupts.
Fixes: 5e2f30b756 "KVM: nVMX: get rid of nested_get_page()"
Cc: stable@vger.kernel.org
Reviewed-by: Andy Honig <ahonig@google.com>
Signed-off-by: Cfir Cohen <cfir@google.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If you register a kvm_coalesced_mmio_zone with '.pio = 0' but then
unregister it with '.pio = 1', KVM_UNREGISTER_COALESCED_MMIO will try to
unregister it from KVM_PIO_BUS rather than KVM_MMIO_BUS, which is a
no-op. But it frees the kvm_coalesced_mmio_dev anyway, causing a
use-after-free.
Fix it by only unregistering and freeing the zone if the correct value
of 'pio' is provided.
Reported-by: syzbot+f87f60bb6f13f39b54e3@syzkaller.appspotmail.com
Fixes: 0804c849f1 ("kvm/x86 : add coalesced pio support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a server side socket is bound to an address, but not in the listening
state yet, incoming connection requests should receive a reset control
packet in response. However, the function used to send the reset
silently drops the reset packet if the sending socket isn't bound
to a remote address (as is the case for a bound socket not yet in
the listening state). This change fixes this by using the src
of the incoming packet as destination for the reset packet in
this case.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-12-18
1) Fix error return code in xfrm_output_one()
when no dst_entry is attached to the skb.
From Wei Yongjun.
2) The xfrm state hash bucket count reported to
userspace is off by one. Fix from Benjamin Poirier.
3) Fix NULL pointer dereference in xfrm_input when
skb_dst_force clears the dst_entry.
4) Fix freeing of xfrm states on acquire. We use a
dedicated slab cache for the xfrm states now,
so free it properly with kmem_cache_free.
From Mathias Krause.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Three fixes: The t10-pi one is a regression from the 4.19 release, the
qla2xxx one is a 4.20 merge window regression and the bnx2fc is a very
old bug.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXBkYeCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishblqAQCN7IcX
hQZcCrtoq6UukGywBtchLangKpFYz96A6VfRqwEAoFDLY72Roi7fsC9Gpll/8Y8H
RmkqIhNzBTODO3L8fiE=
=KFU4
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes: The t10-pi one is a regression from the 4.19 release, the
qla2xxx one is a 4.20 merge window regression and the bnx2fc is a very
old bug"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: t10-pi: Return correct ref tag when queue has no integrity profile
scsi: bnx2fc: Fix NULL dereference in error handling
Revert "scsi: qla2xxx: Fix NVMe Target discovery"
Ido Schimmel says:
====================
mlxsw: VXLAN and firmware flashing fixes
Patch #1 fixes firmware flashing failures by increasing the time period
after which the driver fails the transaction with the firmware. The
problem is explained in detail in the commit message.
Patch #2 adds a missing trap for decapsulated ARP packets. It is
necessary for VXLAN routing to work.
Patch #3 fixes a memory leak during driver reload caused by NULLing a
pointer before kfree().
Please consider patch #1 for 4.19.y
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After a packet was decapsulated it is classified to the relevant FID
based on its VNI and undergoes L2 forwarding.
Unlike regular (non-encapsulated) ARP packets, Spectrum does not trap
decapsulated ARP packets during L2 forwarding and instead can only trap
such packets in the underlay router during decapsulation.
Add this missing packet trap, which is required for VXLAN routing when
the MAC of the target host is not known.
Fixes: b02597d513 ("mlxsw: spectrum: Add NVE packet traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the firmware flash process, some of the EMADs get timed out, which
causes the driver to send them again with a limit of 5 retries. There are
some situations in which 5 retries is not enough and the EMAD access fails.
If the failed EMAD was related to the flashing process, the driver fails
the flashing.
The reason for these timeouts during firmware flashing is cache misses in
the CPU running the firmware. In case the CPU needs to fetch instructions
from the flash when a firmware is flashed, it needs to wait for the
flashing to complete. Since flashing takes time, it is possible for pending
EMADs to timeout.
Fix by increasing EMADs' timeout while flashing firmware.
Fixes: ce6ef68f43 ("mlxsw: spectrum: Implement the ethtool flash_device callback")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the years, xprt_connect_status() has been superseded by
call_connect_status(), which now handles all the errors that
xprt_connect_status() does and more. Since the latter converts
all errors that it doesn't recognise to EIO, then it is time
for it to be retired.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Ensure that we clear XPRT_CONNECTING before releasing the XPRT_LOCK so that
we don't have races between the (asynchronous) socket setup code and
tasks in xprt_connect().
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
When the socket is closed, we need to call xprt_disconnect_done() in order
to clean up the XPRT_WRITE_SPACE flag, and wake up the sleeping tasks.
However, we also want to ensure that we don't wake them up before the socket
is closed, since that would cause thundering herd issues with everyone
piling up to retransmit before the TCP shutdown dance has completed.
Only the task that holds XPRT_LOCKED needs to wake up early in order to
allow the close to complete.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Reported-by: Scott Mayhew <smayhew@redhat.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Recently TXQ teardown was moved earlier in ieee80211_unregister_hw(),
to avoid a use-after-free of the netdev data. However, interfaces
aren't fully removed at the point, and cfg80211_shutdown_all_interfaces
can for example, TX a deauth frame. Move the TXQ teardown to the
point between cfg80211_shutdown_all_interfaces and the free of
netdev queues, so we can be sure they are torn down before netdev
is freed, but after there is no ongoing TX.
Fixes: 77cfaf52ec ("mac80211: Run TXQ teardown code before de-registering interfaces")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn says:
====================
net: SO_TIMESTAMPING fixes
Fix two omissions:
- tx timestamping is missing for AF_INET6/SOCK_RAW/IPPROTO_RAW
- SOF_TIMESTAMPING_OPT_ID is missing for IPPROTO_RAW, PF_PACKET, CAN
Discovered while expanding the selftest in
tools/testing/selftests/networking/timestamping/txtimestamp.c
Will send the test patchset to net-next once the fixes make it to that
branch. For now, it is available at
https://github.com/wdebruij/linux/commits/txtimestamp-test-1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SOF_TIMESTAMPING_OPT_ID is supported on TCP, UDP and RAW sockets.
But it was missing on RAW with IPPROTO_IP, PF_PACKET and CAN.
Add skb_setup_tx_timestamp that configures both tx_flags and tskey
for these paths that do not need corking or use bytestream keys.
Fixes: 09c2d251b7 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raw sockets support tx timestamping, but one case is missing.
IPPROTO_RAW takes a separate packet construction path. raw_send_hdrinc
has an explicit call to sock_tx_timestamp, but rawv6_send_hdrinc does
not. Add it.
Fixes: 11878b40ed ("net-timestamp: SOCK_RAW and PING timestamping")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start the policy_tokens and the associated enumeration from zero,
simplifying the pt macro.
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code uses a bitmap to check for duplicate tokens during parsing, and
that doesn't work at all for the negative Opt_err token case.
There is absolutely no reason to make Opt_err be negative, and in fact
it only confuses things, since some of the affected functions actually
return a positive Opt_xyz enum _or_ a regular negative error code (eg
-EINVAL), and using -1 for Opt_err makes no sense.
There are similar problems in ima_policy.c and key encryption, but they
don't have the immediate bug wrt bitmap handing, and ima_policy.c in
particular needs a different patch to make the enum values match the
token array index. Mimi is sending that separately.
Reported-by: syzbot+a22e0dc07567662c50bc@syzkaller.appspotmail.com
Reported-by: Eric Biggers <ebiggers@kernel.org>
Fixes: 5208cc8342 ("keys, trusted: fix: *do not* allow duplicate key options")
Fixes: 00d60fd3b9 ("KEYS: Provide keyctls to drive the new key type ops for asymmetric keys [ver #2]")
Cc: James Morris James Morris <jmorris@namei.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make my Gmail address the primary one from now on.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c895f6f703 ("bpf: correct broken uapi for
BPF_PROG_TYPE_PERF_EVENT program type"), all architectures
(except um) are required to have bpf_perf_event.h in uapi/asm.
Add it to mandatory-y so "make headers_install" can check it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The dma_direct_supported() function intends to check the DMA mask against
specific values. However, the phys_to_dma() function includes the SME
encryption mask, which defeats the intended purpose of the check. This
results in drivers that support less than 48-bit DMA (SME encryption mask
is bit 47) from being able to set the DMA mask successfully when SME is
active, which results in the driver failing to initialize.
Change the function used to check the mask from phys_to_dma() to
__phys_to_dma() so that the SME encryption mask is not part of the check.
Fixes: c1d0af1a1d ("kernel/dma/direct: take DMA offset into account in dma_direct_supported")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode
again") makes a change to FIFO clearing code which its commit message
suggests was intended to be specific to use with RS485 mode, however:
1) The change made does not just affect __do_stop_tx_rs485(), it also
affects other uses of serial8250_clear_fifos() including paths for
starting up, shutting down or auto-configuring a port regardless of
whether it's an RS485 port or not.
2) It makes the assumption that resetting the FIFOs is a no-op when
FIFOs are disabled, and as such it checks for this case & explicitly
avoids setting the FIFO reset bits when the FIFO enable bit is
clear. A reading of the PC16550D manual would suggest that this is
OK since the FIFO should automatically be reset if it is later
enabled, but we support many 16550-compatible devices and have never
required this auto-reset behaviour for at least the whole git era.
Starting to rely on it now seems risky, offers no benefit, and
indeed breaks at least the Ingenic JZ4780's UARTs which reads
garbage when the RX FIFO is enabled if we don't explicitly reset it.
3) By only resetting the FIFOs if they're enabled, the behaviour of
serial8250_do_startup() during boot now depends on what the value of
FCR is before the 8250 driver is probed. This in itself seems
questionable and leaves us with FCR=0 & no FIFO reset if the UART
was used by 8250_early, otherwise it depends upon what the
bootloader left behind.
4) Although the naming of serial8250_clear_fifos() may be unclear, it
is clear that callers of it expect that it will disable FIFOs. Both
serial8250_do_startup() & serial8250_do_shutdown() contain comments
to that effect, and other callers explicitly re-enable the FIFOs
after calling serial8250_clear_fifos(). The premise of that patch
that disabling the FIFOs is incorrect therefore seems wrong.
For these reasons, this reverts commit f6aa5beb45 ("serial: 8250: Fix
clearing FIFOs in RS485 mode again").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode again").
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # 4.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old firmware versions don't support this command. Sending it
to any firmware before -41.ucode will crash the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201975
Fixes: 66e839030f ("iwlwifi: fix wrong WGDS_WIFI_DATA_SIZE")
CC: <stable@vger.kernel.org> #4.19+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While booting with rootfs on MMC, the following warning is encountered
on OMAP4430:
omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536]
This is because the DMA engine has a default maximum segment size of 64K
but HSMMC sets:
mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
which ends up telling the block layer that we support a maximum segment
size of 65535*512, which exceeds the advertised DMA engine capabilities.
Fix this by clamping the maximum segment size to the lower of the
maximum request size and of the DMA engine device used for either DMA
channel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the SDMMC pads auto calibration values parsed from
devicetree are assigned incorrectly. This patch fixes it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Fixes: 51b77c8ea7 ("mmc: tegra: Program pad autocal offsets from dt")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
V4_MODE is Bit-15 of SDHCI_HOST_CONTROL2 register.
Need to perform word access to this register.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Fixes: b3f80b434f ("mmc: sdhci: Add sd host v4 mode")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the documentation in include/uapi/asm-generic/ioctl.h,
_IOW means userspace is writing and kernel is reading, and
_IOR means userspace is reading and kernel is writing.
In case of these two ioctls, kernel is writing and userspace is reading,
so they have to be _IOR instead of _IOW.
Fixes: 72cd87576d ("block: Introduce BLKGETZONESZ ioctl")
Fixes: 65e4e3eee8 ("block: Introduce BLKGETNRZONES ioctl")
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Recent changes in the mvneta driver reworked allocation
and handling of the ingress buffers to use entire pages.
Apart from that in SW BM scenario the HW must be informed
via PRXDQS about the biggest possible incoming buffer
that can be propagated by RX descriptors.
The BufferSize field was filled according to the MTU-dependent
pkt_size value. Later change to PAGE_SIZE broke RX operation
when usin 64K pages, as the field is simply too small.
This patch conditionally limits the value passed to the BufferSize
of the PRXDQS register, depending on the PAGE_SIZE used.
On the occasion remove now unused frag_size field of the mvneta_port
structure.
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li says:
====================
net: hns: Code improvements & fixes for HNS driver
This patchset introduces some code improvements and fixes
for the identified problems in the HNS driver.
Every patch is independent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata