AMD CPUs affected by the E400 erratum suffer from the issue that the
local APIC timer stops when the CPU goes into C1E. Unfortunately there
is no way to detect the affected CPUs on early boot. It's only possible
to determine the range of possibly affected CPUs from the family/model
range.
The actual decision whether to enter C1E and thus cause the bug is done
by the firmware and we need to detect that case late, after ACPI has
been initialized.
The current solution is to check in the idle routine whether the CPU is
affected by reading the MSR_K8_INT_PENDING_MSG MSR and checking for the
K8_INTP_C1E_ACTIVE_MASK bits. If one of the bits is set then the CPU is
affected and the system is switched into forced broadcast mode.
This is ineffective and on non-affected CPUs every entry to idle does
the extra RDMSR.
After doing some research it turns out that the bits are visible on the
boot CPU right after the ACPI subsystem is initialized in the early
boot process. So instead of polling for the bits in the idle loop, add
a detection function after acpi_subsystem_init() and check for the MSR
bits. If set, then the X86_BUG_AMD_APIC_C1E is set on the boot CPU and
the TSC is marked unstable when X86_FEATURE_NONSTOP_TSC is not set as it
will stop in C1E state as well.
The switch to broadcast mode cannot be done at this point because the
boot CPU still uses HPET as a clockevent device and the local APIC timer
is not yet calibrated and installed. The switch to broadcast mode on the
affected CPUs needs to be done when the local APIC timer is actually set
up.
This allows to cleanup the amd_e400_idle() function in the next step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-4-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The workaround for the AMD Erratum E400 (Local APIC timer stops in C1E
state) is a two step process:
- Selection of the E400 aware idle routine
- Detection whether the platform is affected
The idle routine selection happens for possibly affected CPUs depending on
family/model/stepping information. These range of CPUs is not necessarily
affected as the decision whether to enable the C1E feature is made by the
firmware. Unfortunately there is no way to query this at early boot.
The current implementation polls a MSR in the E400 aware idle routine to
detect whether the CPU is affected. This is inefficient on non affected
CPUs because every idle entry has to do the MSR read.
There is a better way to detect this before going idle for the first time
which requires to seperate the bug flags:
X86_BUG_AMD_E400 - Selects the E400 aware idle routine and
enables the detection
X86_BUG_AMD_APIC_C1E - Set when the platform is affected by E400
Replace the current X86_BUG_AMD_APIC_C1E usage by the new X86_BUG_AMD_E400
bug bit to select the idle routine which currently does an unconditional
detection poll. X86_BUG_AMD_APIC_C1E is going to be used in later patches
to remove the MSR polling and simplify the handling of this misfeature.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-3-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
apm_bios_call() can fail, and return a status in its argument structure.
If that status however is zero during a call from
apm_get_power_status(), we end up using data that may have never been
set, as reported by "gcc -Wmaybe-uninitialized":
arch/x86/kernel/apm_32.c: In function ‘apm’:
arch/x86/kernel/apm_32.c:1729:17: error: ‘bx’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/kernel/apm_32.c:1835:5: error: ‘cx’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/kernel/apm_32.c:1730:17: note: ‘cx’ was declared here
arch/x86/kernel/apm_32.c:1842:27: error: ‘dx’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/kernel/apm_32.c:1731:17: note: ‘dx’ was declared here
This changes the function to return "APM_NO_ERROR" here, which makes the
code more robust to broken BIOS versions, and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent changes, which forced the registration of the boot cpu on UP
systems, which do not have ACPI tables, have been fixed for systems w/o
local APIC, but left a wreckage for systems which have neither ACPI nor
mptables, but the CPU has an APIC, e.g. virtualbox.
The boot process crashes in prefill_possible_map() as it wants to register
the boot cpu, which needs to access the local apic, but the local APIC is
not yet mapped.
There is no reason why init_apic_mapping() can't be invoked before
prefill_possible_map(). So instead of playing another silly early mapping
game, as the ACPI/mptables code does, we just move init_apic_mapping()
before the call to prefill_possible_map().
In hindsight, I should have noticed that combination earlier.
Sorry for the churn (also in stable)!
Fixes: ff8560512b ("x86/boot/smp: Don't try to poke disabled/non-existent APIC")
Reported-and-debugged-by: Michal Necasek <michal.necasek@oracle.com>
Reported-and-tested-by: Wolfgang Bauer <wbauer@tmo.at>
Cc: prarit@redhat.com
Cc: ville.syrjala@linux.intel.com
Cc: michael.thayer@oracle.com
Cc: knut.osmundsen@oracle.com
Cc: frank.mehnert@oracle.com
Cc: Borislav Petkov <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1610282114380.5053@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Specifics:
- Fix three ACPICA issues related to the interpreter locking and
introduced by recent changes in that area (Lv Zheng).
- Fix a PCI IRQ management regression introduced during the 4.7
cycle and related to the configuration of shared IRQs on systems
with an ISA bus (Sinan Kaya).
- Fix up a return value of one function in the APEI code (Punit
Agrawal).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJYE+wwAAoJEILEb/54YlRxe0wQAKIyO3ktsxxbz2iACxFPZGmn
ML1+OTBIGQKYDSGCINhMV5PGd98IMBaVCB9RllG/B9iALb8VCGiJ6AuJKoR7q2pZ
6mr7ioXNfTNlLISykt63cD/Lp/YobZMG6WhoNWzoKslVUQrSWAISV+wGpBxoj08i
8X7t/QtvRIVWfy4H4reDgpQMIKUeDhk6REeb8FESiXYboOvNhbXZpPS+bv8XXEfD
bu/ASQIZs3Z9YB2uTij16Tx95eJETHhr9zYIxbi848YDxjelpZNs1QuVoYxq3GO2
S7vbGHZITMLSEz4jD0w98YvDcb0jywfSXX53NBMaSJqOAleVKNH1rE8KvywG6H0s
2298yBc0o0ldBb+4nszoL7NyGQKDrmxMEGBRFlk67gZ1LA4cpk+Usv9Q0GmNx38H
KQfuA144n9ICaM9Kw9CKD8xrQ+PtpoTIBXzKGsdqIwHsS+2XSwzgp4IWEuMRfZNu
5ermtO2tRz47UDnQ5UxdweB0n2pEMrZXDDzBONdqp3ds4aOvOvVqQP3OB+iMaMrT
rPvVlYLr2Q+ekIzHPCpB7uBwI//bJ3L2cLqHxp9hlbNeFQWdv/NlMlmbWgYVVpn3
tCvqqpH+jtof8lnmWZtBdc4M0GhwM+CP6TYd65n2yDqVCfPraXokE0UdNBW+je4Z
BRuhjVEi0vBsrc3M4IC9
=wjnL
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix recent ACPICA regressions, an older PCI IRQ management
regression, and an incorrect return value of a function in the APEI
code.
Specifics:
- Fix three ACPICA issues related to the interpreter locking and
introduced by recent changes in that area (Lv Zheng).
- Fix a PCI IRQ management regression introduced during the 4.7 cycle
and related to the configuration of shared IRQs on systems with an
ISA bus (Sinan Kaya).
- Fix up a return value of one function in the APEI code (Punit
Agrawal)"
* tag 'acpi-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ACPI / APEI: Fix incorrect return value of ghes_proc()
ACPI/PCI: pci_link: Include PIRQ_PENALTY_PCI_USING for ISA IRQs
ACPI/PCI: pci_link: penalize SCI correctly
ACPI/PCI/IRQ: assign ISA IRQ directly during early boot stages
We needed the physical address of the container in order to compute the
offset within the relocated ramdisk. And we did this by doing __pa() on
the virtual address.
However, __pa() does checks whether the physical address is within
PAGE_OFFSET and __START_KERNEL_map - see __phys_addr() - which fail
if we have CONFIG_RANDOMIZE_MEMORY enabled: we feed a virtual address
which *doesn't* have the randomization offset into a function which uses
PAGE_OFFSET which *does* have that offset.
This makes this check fire:
VIRTUAL_BUG_ON((x > y) || !phys_addr_valid(x));
^^^^^^
due to the randomization offset.
The fix is as simple as using __pa_nodebug() because we do that
randomization offset accounting later in that function ourselves.
Reported-by: Bob Peterson <rpeterso@redhat.com>
Tested-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm <linux-mm@kvack.org>
Cc: stable@vger.kernel.org # 4.9
Link: http://lkml.kernel.org/r/20161027123623.j2jri5bandimboff@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 784d5699ed ("x86: move exports to actual definitions") removed the
EXPORT_SYMBOL(__fentry__) and EXPORT_SYMBOL(mcount) from x8664_ksyms_64.c,
and added EXPORT_SYMBOL(function_hook) in mcount_64.S instead. The problem
is that function_hook isn't a function at all, but a macro that is defined
as either mcount or __fentry__ depending on the support from gcc.
Originally, I thought this was a macro issue, like what __stringify()
is used for. But the problem is a bit deeper. The Makefile.build has
some magic that does post processing of files to create the CRC
bindings. It does some searches for EXPORT_SYMBOL() and because it
finds a macro name and not the actual functions, this causes
function_hook not to be converted into mcount or __fentry__ and they
are missed.
Instead of adding more magic to Makefile.build, just add
EXPORT_SYMBOL() for mcount and __fentry__ where the ifdef is used.
Since this is assembly and not C, it doesn't require being set after
the function is defined.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Borislav Petkov <bp@alien8.de>
Cc: Gabriel C <nix.or.die@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Link: http://lkml.kernel.org/r/20161024150148.4f9d90e4@gandalf.local.home
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gcc -Wmaybe-uninitialized detects that quirk_intel_brickland_xeon_ras_cap
uses uninitialized data when CONFIG_PCI is not set:
arch/x86/kernel/quirks.c: In function ‘quirk_intel_brickland_xeon_ras_cap’:
arch/x86/kernel/quirks.c:641:13: error: ‘capid0’ is used uninitialized in this function [-Werror=uninitialized]
However, the function is also not called in this configuration, so we
can avoid the warning by moving the existing #ifdef to cover it as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20161024153325.2752428-1-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Vince Waver reported the following bug:
WARNING: CPU: 0 PID: 21338 at arch/x86/mm/fault.c:435 vmalloc_fault+0x58/0x1f0
CPU: 0 PID: 21338 Comm: perf_fuzzer Not tainted 4.8.0+ #37
Hardware name: Hewlett-Packard HP Compaq Pro 6305 SFF/1850, BIOS K06 v02.57 08/16/2013
Call Trace:
<NMI> ? dump_stack+0x46/0x59
? __warn+0xd5/0xee
? vmalloc_fault+0x58/0x1f0
? __do_page_fault+0x6d/0x48e
? perf_log_throttle+0xa4/0xf4
? trace_page_fault+0x22/0x30
? __unwind_start+0x28/0x42
? perf_callchain_kernel+0x75/0xac
? get_perf_callchain+0x13a/0x1f0
? perf_callchain+0x6a/0x6c
? perf_prepare_sample+0x71/0x2eb
? perf_event_output_forward+0x1a/0x54
? __default_send_IPI_shortcut+0x10/0x2d
? __perf_event_overflow+0xfb/0x167
? x86_pmu_handle_irq+0x113/0x150
? native_read_msr+0x6/0x34
? perf_event_nmi_handler+0x22/0x39
? perf_ibs_nmi_handler+0x4a/0x51
? perf_event_nmi_handler+0x22/0x39
? nmi_handle+0x4d/0xf0
? perf_ibs_handle_irq+0x3d1/0x3d1
? default_do_nmi+0x3c/0xd5
? do_nmi+0x92/0x102
? end_repeat_nmi+0x1a/0x1e
? entry_SYSCALL_64_after_swapgs+0x12/0x4a
? entry_SYSCALL_64_after_swapgs+0x12/0x4a
? entry_SYSCALL_64_after_swapgs+0x12/0x4a
<EOE> ^A4---[ end trace 632723104d47d31a ]---
BUG: stack guard page was hit at ffffc90008500000 (stack is ffffc900084fc000..ffffc900084fffff)
kernel stack overflow (page fault): 0000 [#1] SMP
...
The NMI hit in the entry code right after setting up the stack pointer
from 'cpu_current_top_of_stack', so the kernel stack was empty. The
'guess' version of __unwind_start() attempted to dereference the "top of
stack" pointer, which is not actually *on* the stack.
Add a check in the guess unwinder to deal with an empty stack. (The
frame pointer unwinder already has such a check.)
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 7c7900f897 ("x86/unwind: Add new unwind interface and implementations")
Link: http://lkml.kernel.org/r/20161024133127.e5evgeebdbohnmpb@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ondrej reported that IRQs stopped working in v4.7 on several
platforms. A typical scenario, from Ondrej's VT82C694X/694X, is:
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: No IRQ available for PCI Interrupt Link [LNKA]
8139too 0000:00:0f.0: PCI INT A: no GSI
We're using PIC routing, so acpi_irq_balance == 0, and LNKA is already
active at IRQ 11. In that case, acpi_pci_link_allocate() only tries
to use the active IRQ (IRQ 11) which also happens to be the SCI.
We should penalize the SCI by PIRQ_PENALTY_PCI_USING, but
irq_get_trigger_type(11) returns something other than
IRQ_TYPE_LEVEL_LOW, so we penalize it by PIRQ_PENALTY_ISA_ALWAYS
instead, which makes acpi_pci_link_allocate() assume the IRQ isn't
available and give up.
Add acpi_penalize_sci_irq() so platforms can tell us the SCI IRQ,
trigger, and polarity directly and we don't have to depend on
irq_get_trigger_type().
Fixes: 103544d869 (ACPI,PCI,IRQ: reduce resource requirements)
Link: http://lkml.kernel.org/r/201609251512.05657.linux@rainbow-software.org
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull x86 fixes from Ingo Molnar:
"Three fixes, a hw-enablement and a cross-arch fix/enablement change:
- SGI/UV fix for older platforms
- x32 signal handling fix
- older x86 platform bootup APIC fix
- AVX512-4VNNIW (Neural Network Instructions) and AVX512-4FMAPS
(Multiply Accumulation Single precision instructions) enablement.
- move thread_info back into x86 specific code, to make life easier
for other architectures trying to make use of
CONFIG_THREAD_INFO_IN_TASK_STRUCT=y"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/smp: Don't try to poke disabled/non-existent APIC
sched/core, x86: Make struct thread_info arch specific again
x86/signal: Remove bogus user_64bit_mode() check from sigaction_compat_abi()
x86/platform/UV: Fix support for EFI_OLD_MEMMAP after BIOS callback updates
x86/cpufeature: Add AVX512_4VNNIW and AVX512_4FMAPS features
x86/vmware: Skip timer_irq_works() check on VMware
Apparently trying to poke a disabled or non-existent APIC
leads to a box that doesn't even boot. Let's not do that.
No real clue if this is the right fix, but at least my
P3 machine boots again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: dyoung@redhat.com
Cc: kexec@lists.infradead.org
Cc: stable@vger.kernel.org
Fixes: 2a51fe083e ("arch/x86: Handle non enumerated CPU after physical hotplug")
Link: http://lkml.kernel.org/r/1477102684-5092-1-git-send-email-ville.syrjala@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The recent introduction of SA_X32/IA32 sa_flags added a check for
user_64bit_mode() into sigaction_compat_abi(). user_64bit_mode() is true
for native 64-bit processes and x32 processes.
Due to that the function returns w/o setting the SA_X32_ABI flag for X32
processes. In consequence the kernel attempts to deliver the signal to the
X32 process in native 64-bit mode causing the process to segfault.
Remove the check, so the actual check for X32 mode which sets the ABI flag
can be reached. There is no side effect for native 64-bit mode.
[ tglx: Rewrote changelog ]
Fixes: 6846351052 ("x86/signal: Add SA_{X32,IA32}_ABI sa_flags")
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: linux-mm@kvack.org
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Link: http://lkml.kernel.org/r/CAJwJo6Z8ZWPqNfT6t-i8GW1MKxQrKDUagQqnZ%2B0%2B697%3DMyVeGg@mail.gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge the gup_flags cleanups from Lorenzo Stoakes:
"This patch series adjusts functions in the get_user_pages* family such
that desired FOLL_* flags are passed as an argument rather than
implied by flags.
The purpose of this change is to make the use of FOLL_FORCE explicit
so it is easier to grep for and clearer to callers that this flag is
being used. The use of FOLL_FORCE is an issue as it overrides missing
VM_READ/VM_WRITE flags for the VMA whose pages we are reading
from/writing to, which can result in surprising behaviour.
The patch series came out of the discussion around commit 38e0885465
("mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing"),
which addressed a BUG_ON() being triggered when a page was faulted in
with PROT_NONE set but having been overridden by FOLL_FORCE.
do_numa_page() was run on the assumption the page _must_ be one marked
for NUMA node migration as an actual PROT_NONE page would have been
dealt with prior to this code path, however FOLL_FORCE introduced a
situation where this assumption did not hold.
See
https://marc.info/?l=linux-mm&m=147585445805166
for the patch proposal"
Additionally, there's a fix for an ancient bug related to FOLL_FORCE and
FOLL_WRITE by me.
[ This branch was rebased recently to add a few more acked-by's and
reviewed-by's ]
* gup_flag-cleanups:
mm: replace access_process_vm() write parameter with gup_flags
mm: replace access_remote_vm() write parameter with gup_flags
mm: replace __access_remote_vm() write parameter with gup_flags
mm: replace get_user_pages_remote() write/force parameters with gup_flags
mm: replace get_user_pages() write/force parameters with gup_flags
mm: replace get_vaddr_frames() write/force parameters with gup_flags
mm: replace get_user_pages_locked() write/force parameters with gup_flags
mm: replace get_user_pages_unlocked() write/force parameters with gup_flags
mm: remove write/force parameters from __get_user_pages_unlocked()
mm: remove write/force parameters from __get_user_pages_locked()
mm: remove gup_flags FOLL_WRITE games from __get_user_pages()
AVX512_4VNNIW - Vector instructions for deep learning enhanced word
variable precision.
AVX512_4FMAPS - Vector instructions for deep learning floating-point
single precision.
These new instructions are to be used in future Intel Xeon & Xeon Phi
processors. The bits 2&3 of CPUID[level:0x07, EDX] inform that new
instructions are supported by a processor.
The spec can be found in the Intel Software Developer Manual (SDM) or in
the Instruction Set Extensions Programming Reference (ISE).
Define new feature flags to enumerate the new instructions in /proc/cpuinfo
accordingly to CPUID bits and add the required xsave extensions which are
required for proper operation.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20161018150111.29926-1-piotr.luc@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The timer_irq_works() boot check may sometimes fail in a VM, when
the Host is overcommitted or when the Guest is running nested.
Since the intended check is unnecessary on VMware's virtual
hardware, by-pass it.
Signed-off-by: Renat Valiullin <rvaliullin@vmware.com>
Acked-by: Alok N Kataria <akataria@vmware.com>
Cc: virtualization@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20161013184539.GA11497@rvaliullin-vm
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This removes the 'write' argument from access_process_vm() and replaces
it with 'gup_flags' as use of this function previously silently implied
FOLL_FORCE, whereas after this patch callers explicitly pass this flag.
We make this explicit as use of FOLL_FORCE can result in surprising
behaviour (and hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit:
917db484dc ("x86/boot: Fix kdump, cleanup aborted E820_PRAM max_pfn manipulation")
... fixed up the broken manipulations of max_pfn in the presence of
E820_PRAM ranges.
However, it also broke the sanitize_e820_map() support for not merging
E820_PRAM ranges.
Re-introduce the enabling to keep resource boundaries between
consecutive defined ranges. Otherwise, for example, an environment that
boots with memmap=2G!8G,2G!10G will end up with a single 4G /dev/pmem0
device instead of a /dev/pmem0 and /dev/pmem1 device 2G in size.
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Zhang Yi <yizhan@redhat.com>
Cc: linux-nvdimm@lists.01.org
Fixes: 917db484dc ("x86/boot: Fix kdump, cleanup aborted E820_PRAM max_pfn manipulation")
Link: http://lkml.kernel.org/r/147629530854.10618.10383744751594021268.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kprobes save and restore raw stack chunks with memcpy().
With KASAN these chunks can contain poisoned stack redzones,
as the result memcpy() interceptor produces false
stack out-of-bounds reports.
Use __memcpy() instead of memcpy() for stack copying.
__memcpy() is not instrumented by KASAN and does not lead
to the false reports.
Currently there is a spew of KASAN reports during boot
if CONFIG_KPROBES_SANITY_TEST is enabled:
[ ] Kprobe smoke test: started
[ ] ==================================================================
[ ] BUG: KASAN: stack-out-of-bounds in setjmp_pre_handler+0x17c/0x280 at addr ffff88085259fba8
[ ] Read of size 64 by task swapper/0/1
[ ] page:ffffea00214967c0 count:0 mapcount:0 mapping: (null) index:0x0
[ ] flags: 0x2fffff80000000()
[ ] page dumped because: kasan: bad access detected
[...]
Reported-by: CAI Qian <caiqian@redhat.com>
Tested-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kasan-dev@googlegroups.com
[ Improved various details. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
===============================
[ INFO: suspicious RCU usage. ]
4.8.0+ #24 Not tainted
-------------------------------
./arch/x86/include/asm/msr-trace.h:47 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
no locks held by swapper/1/0.
[<ffffffff9d492b95>] do_trace_write_msr+0x135/0x140
[<ffffffff9d06f860>] native_write_msr+0x20/0x30
[<ffffffff9d065fad>] native_apic_msr_eoi_write+0x1d/0x30
[<ffffffff9d05bd1d>] smp_reschedule_interrupt+0x1d/0x30
[<ffffffff9d8daec6>] reschedule_interrupt+0x96/0xa0
Reschedule interrupt may be called in cpu idle state. This causes lockdep
check warning above.
Add irq_enter/exit() in smp_reschedule_interrupt(), irq_enter() tells the RCU
subsystems to end the extended quiescent state, so the following trace call in
ack_APIC_irq() works correctly.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Link: http://lkml.kernel.org/r/1476409733-5133-1-git-send-email-wanpeng.li@hotmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull drm updates from Dave Airlie:
"Core:
- Fence destaging work
- DRIVER_LEGACY to split off legacy drm drivers
- drm_mm refactoring
- Splitting drm_crtc.c into chunks and documenting better
- Display info fixes
- rbtree support for prime buffer lookup
- Simple VGA DAC driver
Panel:
- Add Nexus 7 panel
- More simple panels
i915:
- Refactoring GEM naming
- Refactored vma/active tracking
- Lockless request lookups
- Better stolen memory support
- FBC fixes
- SKL watermark fixes
- VGPU improvements
- dma-buf fencing support
- Better DP dongle support
amdgpu:
- Powerplay for Iceland asics
- Improved GPU reset support
- UVD/VEC powergating support for CZ/ST
- Preinitialised VRAM buffer support
- Virtual display support
- Initial SI support
- GTT rework
- PCI shutdown callback support
- HPD IRQ storm fixes
amdkfd:
- bugfixes
tilcdc:
- Atomic modesetting support
mediatek:
- AAL + GAMMA engine support
- Hook up gamma LUT
- Temporal dithering support
imx:
- Pixel clock from devicetree
- drm bridge support for LVDS bridges
- active plane reconfiguration
- VDIC deinterlacer support
- Frame synchronisation unit support
- Color space conversion support
analogix:
- PSR support
- Better panel on/off support
rockchip:
- rk3399 vop/crtc support
- PSR support
vc4:
- Interlaced vblank timing
- 3D rendering CPU overhead reduction
- HDMI output fixes
tda998x:
- HDMI audio ASoC support
sunxi:
- Allwinner A33 support
- better TCON support
msm:
- DT binding cleanups
- Explicit fence-fd support
sti:
- remove sti415/416 support
etnaviv:
- MMUv2 refactoring
- GC3000 support
exynos:
- Refactoring HDMI DCC/PHY
- G2D pm regression fix
- Page fault issues with wait for vblank
There is no nouveau work in this tree, as Ben didn't get a pull
request in, and he was fighting moving to atomic and adding mst
support, so maybe best it waits for a cycle"
* tag 'drm-for-v4.9' of git://people.freedesktop.org/~airlied/linux: (1412 commits)
drm/crtc: constify drm_crtc_index parameter
drm/i915: Fix conflict resolution from backmerge of v4.8-rc8 to drm-next
drm/i915/guc: Unwind GuC workqueue reservation if request construction fails
drm/i915: Reset the breadcrumbs IRQ more carefully
drm/i915: Force relocations via cpu if we run out of idle aperture
drm/i915: Distinguish last emitted request from last submitted request
drm/i915: Allow DP to work w/o EDID
drm/i915: Move long hpd handling into the hotplug work
drm/i915/execlists: Reinitialise context image after GPU hang
drm/i915: Use correct index for backtracking HUNG semaphores
drm/i915: Unalias obj->phys_handle and obj->userptr
drm/i915: Just clear the mmiodebug before a register access
drm/i915/gen9: only add the planes actually affected by ddb changes
drm/i915: Allow PCH DPLL sharing regardless of DPLL_SDVO_HIGH_SPEED
drm/i915/bxt: Fix HDMI DPLL configuration
drm/i915/gen9: fix the watermark res_blocks value
drm/i915/gen9: fix plane_blocks_per_line on watermarks calculations
drm/i915/gen9: minimum scanlines for Y tile is not always 4
drm/i915/gen9: fix the WaWmMemoryReadLatency implementation
drm/i915/kbl: KBL also needs to run the SAGV code
...
KASLR memory randomization can randomize the base of the physical memory
mapping (PAGE_OFFSET), vmalloc (VMALLOC_START) and vmemmap
(VMEMMAP_START). Adding these variables on VMCOREINFO so tools can easily
identify the base of each memory section.
Link: http://lkml.kernel.org/r/1471531632-23003-1-git-send-email-thgarnie@google.com
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Eugene Surovegin <surovegin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Walker reported problems which happens when
crash_kexec_post_notifiers kernel option is enabled
(https://lkml.org/lkml/2015/6/24/44).
In that case, smp_send_stop() is called before entering kdump routines
which assume other CPUs are still online. As the result, for x86, kdump
routines fail to save other CPUs' registers and disable virtualization
extensions.
To fix this problem, call a new kdump friendly function,
crash_smp_send_stop(), instead of the smp_send_stop() when
crash_kexec_post_notifiers is enabled. crash_smp_send_stop() is a weak
function, and it just call smp_send_stop(). Architecture codes should
override it so that kdump can work appropriately. This patch only
provides x86-specific version.
For Xen's PV kernel, just keep the current behavior.
NOTES:
- Right solution would be to place crash_smp_send_stop() before
__crash_kexec() invocation in all cases and remove smp_send_stop(), but
we can't do that until all architectures implement own
crash_smp_send_stop()
- crash_smp_send_stop()-like work is still needed by
machine_crash_shutdown() because crash_kexec() can be called without
entering panic()
Fixes: f06e5153f4 (kernel/panic.c: add "crash_kexec_post_notifiers" option)
Link: http://lkml.kernel.org/r/20160810080948.11028.15344.stgit@sysi4-13.yrl.intra.hitachi.co.jp
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Reported-by: Daniel Walker <dwalker@fifo99.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Xunlei Pang <xpang@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: "Steven J. Hill" <steven.hill@cavium.com>
Cc: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all callers to randomize_range() set the length to 0 and
calculate end by adding a constant to the start address. We can simplify
the API to remove a bunch of needless checks and variables.
Use the new randomize_addr(start, range) call to set the requested
address.
Link: http://lkml.kernel.org/r/20160803233913.32511-3-jason@lakedaemon.net
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull protection keys syscall interface from Thomas Gleixner:
"This is the final step of Protection Keys support which adds the
syscalls so user space can actually allocate keys and protect memory
areas with them. Details and usage examples can be found in the
documentation.
The mm side of this has been acked by Mel"
* 'mm-pkeys-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pkeys: Update documentation
x86/mm/pkeys: Do not skip PKRU register if debug registers are not used
x86/pkeys: Fix pkeys build breakage for some non-x86 arches
x86/pkeys: Add self-tests
x86/pkeys: Allow configuration of init_pkru
x86/pkeys: Default to a restrictive init PKRU
pkeys: Add details of system call use to Documentation/
generic syscalls: Wire up memory protection keys syscalls
x86: Wire up protection keys system calls
x86/pkeys: Allocation/free syscalls
x86/pkeys: Make mprotect_key() mask off additional vm_flags
mm: Implement new pkey_mprotect() system call
x86/pkeys: Add fault handling for PF_PK page fault bit
Pull x86 updates from Thomas Gleixner:
"A pile of regression fixes and updates:
- address the fallout of the patches which made the cpuid - nodeid
relation permanent: Handling of invalid APIC ids and preventing
pointless warning messages.
- force eager FPU when protection keys are enabled. Protection keys
are not generating FPU exceptions so they cannot work with the lazy
FPU mechanism.
- prevent force migration of interrupts which are not part of the CPU
vector domain.
- handle the fact that APIC ids are not updated in the ACPI/MADT
tables on physical CPU hotplug
- remove bash-isms from syscall table generator script
- use the hypervisor supplied APIC frequency when running on VMware"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pkeys: Make protection keys an "eager" feature
x86/apic: Prevent pointless warning messages
x86/acpi: Prevent LAPIC id 0xff from being accounted
arch/x86: Handle non enumerated CPU after physical hotplug
x86/unwind: Fix oprofile module link error
x86/vmware: Skip lapic calibration on VMware
x86/syscalls: Remove bash-isms in syscall table generator
x86/irq: Prevent force migration of irqs which are not in the vector domain
Markus reported that he sees new warnings:
APIC: NR_CPUS/possible_cpus limit of 4 reached. Processor 4/0x84 ignored.
APIC: NR_CPUS/possible_cpus limit of 4 reached. Processor 5/0x85 ignored.
This comes from the recent persistant cpuid - nodeid changes. The code
which emits the warning has been called prior to these changes only for
enabled processors. Now it's called for disabled processors as well to get
the possible cpu accounting correct. So if the kernel is compiled for the
number of actual available/enabled CPUs and the BIOS reports disabled CPUs
as well then the above warnings are printed.
That's a pointless exercise as it only makes sense if there are more CPUs
enabled than the kernel supports.
Nake the warning conditional on enabled processors so we are back to the
state before these changes.
Fixes: 8f54969dc8 ("x86/acpi: Introduce persistent storage for cpuid <-> apicid mapping")
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: linux-acpi@vger.kernel.org
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1610071549330.19804@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Yinghai reported that the recent changes to make the cpuid - nodeid
relationship permanent causes a cpuid ordering regression on a system which
has 2apic enabled..
The reason is that the ACPI local APIC parser has no sanity check for
apicid 0xff, which is an invalid id. So a CPU id for this invalid local
APIC id is allocated and therefor breaks the cpuid ordering.
Add a sanity check to acpi_parse_lapic() which ignores the invalid id.
Fixes: 8f54969dc8 ("x86/acpi: Introduce persistent storage for cpuid <-> apicid mapping")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>,
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: douly.fnst@cn.fujitsu.com,
Cc: zhugh.fnst@cn.fujitsu.com
Cc: Tony Luck <tony.luck@intel.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Lv Zheng <lv.zheng@intel.com>,
Cc: robert.moore@intel.com
Cc: linux-acpi@vger.kernel.org
Link: https://lkml.kernel.org/r/CAE9FiQVQx6FRXT-RdR7Crz4dg5LeUWHcUSy1KacjR+JgU_vGJg@mail.gmail.com
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "improvements to the nmi_backtrace code" v9.
This patch series modifies the trigger_xxx_backtrace() NMI-based remote
backtracing code to make it more flexible, and makes a few small
improvements along the way.
The motivation comes from the task isolation code, where there are
scenarios where we want to be able to diagnose a case where some cpu is
about to interrupt a task-isolated cpu. It can be helpful to see both
where the interrupting cpu is, and also an approximation of where the
cpu that is being interrupted is. The nmi_backtrace framework allows us
to discover the stack of the interrupted cpu.
I've tested that the change works as desired on tile, and build-tested
x86, arm, mips, and sparc64. For x86 I confirmed that the generic
cpuidle stuff as well as the architecture-specific routines are in the
new cpuidle section. For arm, mips, and sparc I just build-tested it
and made sure the generic cpuidle routines were in the new cpuidle
section, but I didn't attempt to figure out which the platform-specific
idle routines might be. That might be more usefully done by someone
with platform experience in follow-up patches.
This patch (of 4):
Currently you can only request a backtrace of either all cpus, or all
cpus but yourself. It can also be helpful to request a remote backtrace
of a single cpu, and since we want that, the logical extension is to
support a cpumask as the underlying primitive.
This change modifies the existing lib/nmi_backtrace.c code to take a
cpumask as its basic primitive, and modifies the linux/nmi.h code to use
the new "cpumask" method instead.
The existing clients of nmi_backtrace (arm and x86) are converted to
using the new cpumask approach in this change.
The other users of the backtracing API (sparc64 and mips) are converted
to use the cpumask approach rather than the all/allbutself approach.
The mips code ignored the "include_self" boolean but with this change it
will now also dump a local backtrace if requested.
Link: http://lkml.kernel.org/r/1472487169-14923-2-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull livepatching updates from Jiri Kosina:
- fix for patching modules that contain .altinstructions or
.parainstructions sections, from Jessica Yu
- make TAINT_LIVEPATCH a per-module flag (so that it's immediately
clear which module caused the taint), from Josh Poimboeuf
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch/module: make TAINT_LIVEPATCH module-specific
Documentation: livepatch: add section about arch-specific code
livepatch/x86: apply alternatives and paravirt patches after relocations
livepatch: use arch_klp_init_object_loaded() to finish arch-specific tasks
When a CPU is physically added to a system then the MADT table is not
updated.
If subsequently a kdump kernel is started on that physically added CPU then
the ACPI enumeration fails to provide the information for this CPU which is
now the boot CPU of the kdump kernel.
As a consequence, generic_processor_info() is not invoked for that CPU so
the number of enumerated processors is 0 and none of the initializations,
including the logical package id management, are performed.
We have code which relies on the correctness of the logical package map and
other information which is initialized via generic_processor_info().
Executing such code will result in undefined behaviour or kernel crashes.
This problem applies only to the kdump kernel because a normal kexec will
switch to the original boot CPU, which is enumerated in MADT, before
jumping into the kexec kernel.
The boot code already has a check for num_processors equal 0 in
prefill_possible_map(). We can use that check as an indicator that the
enumeration of the boot CPU did not happen and invoke generic_processor_info()
for it. That initializes the relevant data for the boot CPU and therefore
prevents subsequent failure.
[ tglx: Refined the code and rewrote the changelog ]
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 1f12e32f4c ("x86/topology: Create logical package id")
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: dyoung@redhat.com
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: kexec@lists.infradead.org
Link: http://lkml.kernel.org/r/1475514432-27682-1-git-send-email-prarit@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All architectures:
Move `make kvmconfig` stubs from x86; use 64 bits for debugfs stats.
ARM:
Important fixes for not using an in-kernel irqchip; handle SError
exceptions and present them to guests if appropriate; proxying of GICV
access at EL2 if guest mappings are unsafe; GICv3 on AArch32 on ARMv8;
preparations for GICv3 save/restore, including ABI docs; cleanups and
a bit of optimizations.
MIPS:
A couple of fixes in preparation for supporting MIPS EVA host kernels;
MIPS SMP host & TLB invalidation fixes.
PPC:
Fix the bug which caused guests to falsely report lockups; other minor
fixes; a small optimization.
s390:
Lazy enablement of runtime instrumentation; up to 255 CPUs for nested
guests; rework of machine check deliver; cleanups and fixes.
x86:
IOMMU part of AMD's AVIC for vmexit-less interrupt delivery; Hyper-V
TSC page; per-vcpu tsc_offset in debugfs; accelerated INS/OUTS in
nVMX; cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJX9iDrAAoJEED/6hsPKofoOPoIAIUlgojkb9l2l1XVDgsXdgQL
sRVhYSVv7/c8sk9vFImrD5ElOPZd+CEAIqFOu45+NM3cNi7gxip9yftUVs7wI5aC
eDZRWm1E4trDZLe54ZM9ThcqZzZZiELVGMfR1+ZndUycybwyWzafpXYsYyaXp3BW
hyHM3qVkoWO3dxBWFwHIoO/AUJrWYkRHEByKyvlC6KPxSdBPSa5c1AQwMCoE0Mo4
K/xUj4gBn9eMelNhg4Oqu/uh49/q+dtdoP2C+sVM8bSdquD+PmIeOhPFIcuGbGFI
B+oRpUhIuntN39gz8wInJ4/GRSeTuR2faNPxMn4E1i1u4LiuJvipcsOjPfe0a18=
=fZRB
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"All architectures:
- move `make kvmconfig` stubs from x86
- use 64 bits for debugfs stats
ARM:
- Important fixes for not using an in-kernel irqchip
- handle SError exceptions and present them to guests if appropriate
- proxying of GICV access at EL2 if guest mappings are unsafe
- GICv3 on AArch32 on ARMv8
- preparations for GICv3 save/restore, including ABI docs
- cleanups and a bit of optimizations
MIPS:
- A couple of fixes in preparation for supporting MIPS EVA host
kernels
- MIPS SMP host & TLB invalidation fixes
PPC:
- Fix the bug which caused guests to falsely report lockups
- other minor fixes
- a small optimization
s390:
- Lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups and fixes
x86:
- IOMMU part of AMD's AVIC for vmexit-less interrupt delivery
- Hyper-V TSC page
- per-vcpu tsc_offset in debugfs
- accelerated INS/OUTS in nVMX
- cleanups and fixes"
* tag 'kvm-4.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (140 commits)
KVM: MIPS: Drop dubious EntryHi optimisation
KVM: MIPS: Invalidate TLB by regenerating ASIDs
KVM: MIPS: Split kernel/user ASID regeneration
KVM: MIPS: Drop other CPU ASIDs on guest MMU changes
KVM: arm/arm64: vgic: Don't flush/sync without a working vgic
KVM: arm64: Require in-kernel irqchip for PMU support
KVM: PPC: Book3s PR: Allow access to unprivileged MMCR2 register
KVM: PPC: Book3S PR: Support 64kB page size on POWER8E and POWER8NVL
KVM: PPC: Book3S: Remove duplicate setting of the B field in tlbie
KVM: PPC: BookE: Fix a sanity check
KVM: PPC: Book3S HV: Take out virtual core piggybacking code
KVM: PPC: Book3S: Treat VTB as a per-subcore register, not per-thread
ARM: gic-v3: Work around definition of gic_write_bpr1
KVM: nVMX: Fix the NMI IDT-vectoring handling
KVM: VMX: Enable MSR-BASED TPR shadow even if APICv is inactive
KVM: nVMX: Fix reload apic access page warning
kvmconfig: add virtio-gpu to config fragment
config: move x86 kvm_guest.config to a common location
arm64: KVM: Remove duplicating init code for setting VMID
ARM: KVM: Support vgic-v3
...
When compiling on x86 with CONFIG_OPROFILE=m and CONFIG_FRAME_POINTER=n,
the oprofile module fails to link:
ERROR: ftrace_graph_ret_addr" [arch/x86/oprofile/oprofile.ko] undefined!
The problem was introduced when oprofile was converted to use the new
x86 unwinder. When frame pointers are disabled, the "guess" unwinder's
unwind_get_return_address() is an inline function which calls
ftrace_graph_ret_addr(), which is not exported.
Fix it by converting the "guess" version of unwind_get_return_address()
to an exported out-of-line function, just like its frame pointer
counterpart.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: ec2ad9ccf1 ("oprofile/x86: Convert x86_backtrace() to use the new unwinder")
Link: http://lkml.kernel.org/r/be08d589f6474df78364e081c42777e382af9352.1475731632.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In a virtualized environment the APIC timer calibration can go wrong when
the host is overcommitted or the guest is running nested. This results
in the APIC timers operating at an incorrect frequency.
Since VMware supports a mechanism to retrieve the local APIC frequency we
can ask the hypervisor for it and skip the APIC calibration loop.
Signed-off-by: Renat Valiullin <rvaliullin@vmware.com>
Acked-by: Alok N Kataria <akataria@vmware.com>
Cc: virtualization@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20161004201148.GA1421@uu64vm
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When a CPU is about to be offlined we call fixup_irqs() that resets IRQ
affinities related to the CPU in question. The same thing is also done when
the system is suspended to S-states like S3 (mem).
For each IRQ we try to complete any on-going move regardless whether the
IRQ is actually part of x86_vector_domain. For each IRQ descriptor we fetch
its chip_data, assume it is of type struct apic_chip_data and manipulate it
by clearing old_domain mask etc. For irq_chips that are not part of the
x86_vector_domain, like those created by various GPIO drivers, will find
their chip_data being changed unexpectly.
Below is an example where GPIO chip owned by pinctrl-sunrisepoint.c gets
corrupted after resume:
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in hi
# rtcwake -s10 -mmem
<10 seconds passes>
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in ?
Note '?' in the output. It means the struct gpio_chip ->get function is
NULL whereas before suspend it was there.
Fix this by first checking that the IRQ belongs to x86_vector_domain before
we try to use the chip_data as struct apic_chip_data.
Reported-and-tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org # 4.4+
Link: http://lkml.kernel.org/r/20161003101708.34795-1-mika.westerberg@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
Pull x86 vdso updates from Ingo Molnar:
"The main changes in this cycle centered around adding support for
32-bit compatible C/R of the vDSO on 64-bit kernels, by Dmitry
Safonov"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Use CONFIG_X86_X32_ABI to enable vdso prctl
x86/vdso: Only define map_vdso_randomized() if CONFIG_X86_64
x86/vdso: Only define prctl_map_vdso() if CONFIG_CHECKPOINT_RESTORE
x86/signal: Add SA_{X32,IA32}_ABI sa_flags
x86/ptrace: Down with test_thread_flag(TIF_IA32)
x86/coredump: Use pr_reg size, rather that TIF_IA32 flag
x86/arch_prctl/vdso: Add ARCH_MAP_VDSO_*
x86/vdso: Replace calculate_addr in map_vdso() with addr
x86/vdso: Unmap vdso blob on vvar mapping failure
Pull x86 timer updates from Ingo Molnar:
"This tree includes a HPET overhead micro-optimization plus new TSC
frequencies for newer Intel CPUs"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Add additional Intel CPU models to the crystal quirk list
x86/tsc: Use cpu id defines instead of hex constants
x86/hpet: Reduce HPET counter read contention
Pull x86 cleanups from Ingo Molnar:
"Header file and a wrapper functions cleanup"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Migrate exception table users off module.h and onto extable.h
x86: Clean up various simple wrapper functions
Pull x86 boot updates from Ingo Molnar:
"The changes in this cycle were:
- Save e820 table RAM footprint on larger kernel configurations.
(Denys Vlasenko)
- pmem related fixes (Dan Williams)
- theoretical e820 boundary condition fix (Wei Yang)"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix kdump, cleanup aborted E820_PRAM max_pfn manipulation
x86/e820: Use much less memory for e820/e820_saved, save up to 120k
x86/e820: Prepare e280 code for switch to dynamic storage
x86/e820: Mark some static functions __init
x86/e820: Fix very large 'size' handling boundary condition
Pull low-level x86 updates from Ingo Molnar:
"In this cycle this topic tree has become one of those 'super topics'
that accumulated a lot of changes:
- Add CONFIG_VMAP_STACK=y support to the core kernel and enable it on
x86 - preceded by an array of changes. v4.8 saw preparatory changes
in this area already - this is the rest of the work. Includes the
thread stack caching performance optimization. (Andy Lutomirski)
- switch_to() cleanups and all around enhancements. (Brian Gerst)
- A large number of dumpstack infrastructure enhancements and an
unwinder abstraction. The secret long term plan is safe(r) live
patching plus maybe another attempt at debuginfo based unwinding -
but all these current bits are standalone enhancements in a frame
pointer based debug environment as well. (Josh Poimboeuf)
- More __ro_after_init and const annotations. (Kees Cook)
- Enable KASLR for the vmemmap memory region. (Thomas Garnier)"
[ The virtually mapped stack changes are pretty fundamental, and not
x86-specific per se, even if they are only used on x86 right now. ]
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
x86/asm: Get rid of __read_cr4_safe()
thread_info: Use unsigned long for flags
x86/alternatives: Add stack frame dependency to alternative_call_2()
x86/dumpstack: Fix show_stack() task pointer regression
x86/dumpstack: Remove dump_trace() and related callbacks
x86/dumpstack: Convert show_trace_log_lvl() to use the new unwinder
oprofile/x86: Convert x86_backtrace() to use the new unwinder
x86/stacktrace: Convert save_stack_trace_*() to use the new unwinder
perf/x86: Convert perf_callchain_kernel() to use the new unwinder
x86/unwind: Add new unwind interface and implementations
x86/dumpstack: Remove NULL task pointer convention
fork: Optimize task creation by caching two thread stacks per CPU if CONFIG_VMAP_STACK=y
sched/core: Free the stack early if CONFIG_THREAD_INFO_IN_TASK
lib/syscall: Pin the task stack in collect_syscall()
x86/process: Pin the target stack in get_wchan()
x86/dumpstack: Pin the target stack when dumping it
kthread: Pin the stack via try_get_task_stack()/put_task_stack() in to_live_kthread() function
sched/core: Add try_get_task_stack() and put_task_stack()
x86/entry/64: Fix a minor comment rebase error
iommu/amd: Don't put completion-wait semaphore on stack
...
Pull x86 apic updates from Ingo Molnar:
"The main changes are:
- Persistent CPU/node numbering across CPU hotplug/unplug events.
This is a pretty involved series of changes that first fetches all
the information during bootup and then uses it for the various
hotplug/unplug methods. (Gu Zheng, Dou Liyang)
- IO-APIC hot-add/remove fixes and enhancements. (Rui Wang)
- ... various fixes, cleanups and enhancements"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86/apic: Fix silent & fatal merge conflict in __generic_processor_info()
acpi: Fix broken error check in map_processor()
acpi: Validate processor id when mapping the processor
acpi: Provide mechanism to validate processors in the ACPI tables
x86/acpi: Set persistent cpuid <-> nodeid mapping when booting
x86/acpi: Enable MADT APIs to return disabled apicids
x86/acpi: Introduce persistent storage for cpuid <-> apicid mapping
x86/acpi: Enable acpi to register all possible cpus at boot time
x86/numa: Online memory-less nodes at boot time
x86/apic: Get rid of apic_version[] array
x86/apic: Order irq_enter/exit() calls correctly vs. ack_APIC_irq()
x86/ioapic: Ignore root bridges without a companion ACPI device
x86/apic: Update comment about disabling processor focus
x86/smpboot: Check APIC ID before setting up default routing
x86/ioapic: Fix IOAPIC failing to request resource
x86/ioapic: Fix lost IOAPIC resource after hot-removal and hotadd
x86/ioapic: Fix setup_res() failing to get resource
x86/ioapic: Support hot-removal of IOAPICs present during boot
x86/ioapic: Change prototype of acpi_ioapic_add()
x86/apic, ACPI: Fix incorrect assignment when handling apic/x2apic entries
...
