Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9063 RTC and OnKey subnode to DA9063 PMIC node on Silk.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9063 PMIC node to the I2C bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The vin port node does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7794-silk.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef0000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend the Silk board support to include SW3, SW4, SW6 and SW12. They
are all connected via GPIO lines and handled by the gpio-keys driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend the Silk board support to include U14 which is an I2C based EEPROM
hooked up to the I2C1 bus.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Convert the R-Car E2 SoC from the old "Renesas R-Car Gen2 Clock Pulse
Generator (CPG)", "Renesas CPG DIV6 Clock", and "Renesas CPG Module Stop
(MSTP) Clocks" DT bindings to the new unified "Renesas Clock Pulse
Generator / Module Standby and Software Reset" DT bindings.
This simplifies the DTS files, and allows to add support for reset
control later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 84e734f497 ("ARM: dts: silk: add DU DT support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the R8A7794 sound device node.
Add device node for Asahi Kasei AK4643 stereo codec to the I2C1 bus.
Add the "simple-audio-card" device node to interconnect the SoC sound
device and the codec.
This patch is based on the commit 493b4da7c1 ("ARM: dts: porter: add
sound support").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) DU pin data to the SILK board's device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /regulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the silk device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the DU device node.
Add the device nodes for the Analog Devices ADV7511W HDMI transmitter
(connected to DU0) and ADV7123 video DAC (connected to DU1). Add the
necessary subnodes to interconnect DU, HDMI/VDAC devices, and HDMI/VGA
connectors.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support partitions
in a special 'partitions' subnode"), having partitions as direct subnodes
of an mtd device is discouraged. Hence move the SPI FLASH partitions to a
"partitions" subnode.
Based on similar work for the koelsch board by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the SDHI1 (connected to micro-SD
slot) device nodes along with the necessary voltage regulators.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB PHY device for the SILK board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the VIN0 device node.
Add the device node for Analog Devices ADV7180 video decoder to I2C1 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.
Based on the Henninger VIN0/ADV8170 device tree patch by myself.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the I2C1 device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and MTD partitions on it.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the MMCIF device node (the board has
eMMC chip) along with the necessary voltage regulator (note that the Vcc/Vccq
regulator is dummy -- it's required by the MMCIF driver but doesn't actually
exist on the board).
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7794 SoC based SILK low cost board.
SCIF2 serial port support is included, so that the serial console can work.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm