So far we've enabled pull-up and pull-down resistors on GPIOs using a
pinctrl node. Now that the GPIO binding allows for a flag to declare this,
let's switch to it.
This brings us closer to removing all the GPIO pinctrl nodes, which will in
turn allow us to switch the pinctrl strict mode on.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
While the USB PHY Device Tree mandates that the name of the VBUS detect pin
should be usb0_vbus_det-gpios, a significant number of device tree use
usb0_vbus_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
While the USB PHY Device Tree mandates that the name of the ID detect pin
should be usb0_id_det-gpios, a significant number of device tree use
usb0_id_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The I2C's, MMC0 and EMAC controllers have only one muxing option in the
SoC. In such a case, we can just move the muxing into the DTSI, and remove
it from the DTS.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As part of our effort to move pinctrl/GPIO interlocking into the
driver where it belongs, this patch drops the definition and usage
of the mmc0_cd_pin_reference_design pinmux setting for the default
mmc0 card detect GPIO pin.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add a node describing the focaltech ft5306de4 touchscreen found on
chuwi-v7-cw0825 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c1 has a freescale mma7660 accelerometer connected to it at addr 0x4c,
i2c2 has a ft5x touchscreen connected to it at addr 0x38.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the Chuwi V7 CW0825 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the lradc controlled tablet keys on the Chuwi V7 CW0825 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.
It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard