All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add a node enabling the gsl3670 touchscreen controller found on
sun8i-a23-polaroid-mid2809pxe04 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The polaroid-mid2809 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This results in quite a nice cleanup for this dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Polaroid mid2809pxe04 tablet uses an sdio esp8089 wifi chip, so
ehci0 is not used and should be disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked
Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD,
A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard