Add support for SCDC Setup for TMDS Clock > 3.4GHz and enable TMDS
Scrambling when supported or mandatory.
This patch also adds an helper to setup the control bit to support
the high TMDS Bit Period/TMDS Clock-Period Ratio as required with
TMDS Clock > 3.4GHz for HDMI2.0 3840x2160@60/50 modes.
These changes were based on work done by Huicong Xu <xhc@rock-chips.com>
and Nickey Yang <nickey.yang@rock-chips.com> to support HDMI2.0 modes
on the Rockchip 4.4 BSP kernel at [1]
[1] https://github.com/rockchip-linux/kernel/tree/release-4.4
Cc: Nickey Yang <nickey.yang@rock-chips.com>
Cc: Huicong Xu <xhc@rock-chips.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1549022873-40549-2-git-send-email-narmstrong@baylibre.com
UAPI Changes:
- New fourcc identifier for ARM Framebuffer Compression v1.3
Cross-subsystem Changes:
Core Changes:
- Reorganisation of drm_device and drm_framebuffer headers
- Cleanup of the drmP inclusion
- Fix leaks in the fb-helpers
- Allow for depth different from bpp in fb-helper fbdev emulation
- Remove drm_mode_object from drm_display_mode
Driver Changes:
- Add reflection properties to rockchip
- a bunch of fixes for virtio
- a bunch of fixes for dp_mst and drivers using it, and introduction of a
new refcounting scheme
- Convertion of bochs to atomic and generic fbdev emulation
- Allow meson to remove the firmware framebuffers
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXD+OHgAKCRDj7w1vZxhR
xe3IAP4s59sFVMZseVJpwSe41OJ1ipD/cyIbtXU94X6nFd6zCAD+Jm4q+XIIS+uv
7ElmJ2BD7rwicqSViWNG8tteHYfjrAU=
=XPsb
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-01-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
- New fourcc identifier for ARM Framebuffer Compression v1.3
Cross-subsystem Changes:
Core Changes:
- Reorganisation of drm_device and drm_framebuffer headers
- Cleanup of the drmP inclusion
- Fix leaks in the fb-helpers
- Allow for depth different from bpp in fb-helper fbdev emulation
- Remove drm_mode_object from drm_display_mode
Driver Changes:
- Add reflection properties to rockchip
- a bunch of fixes for virtio
- a bunch of fixes for dp_mst and drivers using it, and introduction of a
new refcounting scheme
- Convertion of bochs to atomic and generic fbdev emulation
- Allow meson to remove the firmware framebuffers
[airlied: patch rcar-du to add drm_modes.h]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190116200428.u2n4jbk4mzza7n6e@flea
The mode and ajusted_mode passed to the bridge .mode_set() operation
should never be modified by the bridge (and are not in any of the
existing bridge drivers). Make them const to make this clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drmP.h is an relic from the days when there was a single header file.
To enable the removal of drmP.h from all users drop include
of drmP.h from bridge/dw_hdmi.h.
A few files relied on the file included in drmP.h - add explicit
include statements or forward declarations to these files.
Build tested with arm and x86.
v2:
- prefer forward declarations when possible (Laurent Pinchart)
- sort include files (Laurent Pinchart)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-7-sam@ravnborg.org
Allow to also drive a slave dw-mipi-dsi controller in a dual-dsi
setup. This will require additional implementation-specific
code to look up the slave instance and do specific setup.
Also will probably need code in the specific crtcs as dual-dsi
does not equal two separate dsi outputs.
To activate, the implementation-specific code should set the slave
using dw_mipi_dsi_set_slave() before calling __dw_mipi_dsi_bind().
v2:
- expect real interface number of lanes
- keep links to both master and slave
v3:
- remove unneeded separate variables
- remove unneeded second slave settings
- disable slave before master
- lane-sum calculation comments
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-7-heiko@sntech.de
With the regular means of adding the dsi-component in probe it creates
a race condition with the panel probing, as the panel device only gets
created after the dsi-bus got created.
When the panel-driver is build as a module it currently fails hard as the
panel cannot be probed directly:
dw_mipi_dsi_bind()
__dw_mipi_dsi_probe()
creates dsi bus
creates panel device
triggers panel module load
panel not probed (module not loaded or panel probe slow)
drm_bridge_attach
fails with -EINVAL due to empty panel_bridge
Additionally the panel probing can run concurrently with dsi bringup
making it possible that the panel can already be found but dsi-attach
hasn't finished running.
To solve that cleanly we may want to only create the component after
the panel has finished probing, by calling component_add from the
host-attach dsi callback.
As that is specific to glue drivers, add a new struct for host_ops
so that glue drivers can tell the bridge to call specific functions
after the common host-attach and before the common host-detach run.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-4-heiko@sntech.de
__dw_mipi_dsi_probe() does all the grabbing of resources and does it using
devm-helpers. So this is happening on each try of master bringup possibly
slowing down things a lot.
Drivers using the component framework may instead want to call
dw_mipi_dsi_probe separately in their probe function to setup resources
early. That way the dsi bus also gets created earlier and also not
recreated on each bind-try, so that attached panels can load their modules
and be probed way before the bridge-attach in the bind call.
So drop the call to __dw_mipi_dsi_probe and modify the function to take
a struct dw_mipi_dsi instead of the platform-device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-3-heiko@sntech.de
In some IP implementations the reading of the phy-type may be broken.
One example are the Rockchip rk3228 and rk3328 socs that use a separate
vendor-type phy from Innosilicon but still report the HDMI20_TX type.
So allow the glue driver to force the vendor-phy for these cases.
In the future it may be necessary to allow forcing other types, but
for now we'll keep it simply to the case actually seen in the wild.
changes in v3:
- only allow forcing vendor type, as suggested by Laurent
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Zheng Yang <zhengyang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-2-heiko@sntech.de
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-3-heiko@sntech.de
-----BEGIN PGP SIGNATURE-----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=twst
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This starts to support NVIDIA volta hardware with nouveau, and adds
amdgpu support for the GPU in the Kabylake-G (the intel + radeon
single package chip), along with some initial Intel icelake enabling.
Summary:
New Drivers:
- v3d - driver for broadcom V3D V3.x+ hardware
- xen-front - XEN PV display frontend
core:
- handle zpos normalization in the core
- stop looking at legacy pointers in atomic paths
- improved scheduler documentation
- improved aspect ratio validation
- aspect ratio support for 64:27 and 256:135
- drop unused control node code.
i915:
- Icelake (ICL) enabling
- GuC/HuC refactoring
- PSR/PSR2 enabling and fixes
- DPLL management refactoring
- DP MST fixes
- NV12 enabling
- HDCP improvements
- GEM/Execlist/reset improvements
- GVT improvements
- stolen memory first 4k fix
amdgpu:
- Vega 20 support
- VEGAM support (Kabylake-G)
- preOS scanout buffer reservation
- power management gfxoff support for raven
- SR-IOV fixes
- Vega10 power profiles and clock voltage control
- scatter/gather display support on CZ/ST
amdkfd:
- GFX9 dGPU support
- userptr memory mapping
nouveau:
- major refactoring for Volta GV100 support
tda998x:
- HDMI i2c CEC support
etnaviv:
- removed unused logging code
- license text cleanups
- MMU handling improvements
- timeout fence fix for 50 days uptime
tegra:
- IOMMU support in gr2d/gr3d drivers
- zpos support
vc4:
- syncobj support
- CTM, plane alpha and async cursor support
analogix_dp:
- HPD and aux chan fixes
sun4i:
- MIPI DSI support
tilcdc:
- clock divider fixes for OMAP-l138 LCDK board
rcar-du:
- R8A77965 support
- dma-buf fences fixes
- hardware indexed crtc/du group handling
- generic zplane property support
atmel-hclcdc:
- generic zplane property support
mediatek:
- use generic video mode function
exynos:
- S5PV210 FIMD variant support
- IPP v2 framework
- more HW overlays support"
* tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm: (1286 commits)
drm/amdgpu: fix 32-bit build warning
drm/exynos: fimc: signedness bug in fimc_setup_clocks()
drm/exynos: scaler: fix static checker warning
drm/amdgpu: Use dev_info() to report amdkfd is not supported for this ASIC
drm/amd/display: Remove use of division operator for long longs
drm/amdgpu: Update GFX info structure to match what vega20 used
drm/amdgpu/pp: remove duplicate assignment
drm/sched: add rcu_barrier after entity fini
drm/amdgpu: move VM BOs on LRU again
drm/amdgpu: consistenly use VM moved flag
drm/amdgpu: kmap PDs/PTs in amdgpu_vm_update_directories
drm/amdgpu: further optimize amdgpu_vm_handle_moved
drm/amdgpu: cleanup amdgpu_vm_validate_pt_bos v2
drm/amdgpu: rework VM state machine lock handling v2
drm/amdgpu: Add runtime VCN PG support
drm/amdgpu: Enable VCN static PG by default on RV
drm/amdgpu: Add VCN static PG support on RV
drm/amdgpu: Enable VCN CG by default on RV
drm/amdgpu: Add static CG control for VCN on RV
drm/exynos: Fix default value for zpos plane property
...
The dw_hdmi_setup_rx_sense exported function should not use struct device
to recover the dw-hdmi context using drvdata, but take struct dw_hdmi
directly like other exported functions.
This caused a regression using Meson DRM on S905X since v4.17-rc1 :
Internal error: Oops: 96000007 [#1] PREEMPT SMP
[...]
CPU: 0 PID: 124 Comm: irq/32-dw_hdmi_ Not tainted 4.17.0-rc7 #2
Hardware name: Libre Technology CC (DT)
[...]
pc : osq_lock+0x54/0x188
lr : __mutex_lock.isra.0+0x74/0x530
[...]
Process irq/32-dw_hdmi_ (pid: 124, stack limit = 0x00000000adf418cb)
Call trace:
osq_lock+0x54/0x188
__mutex_lock_slowpath+0x10/0x18
mutex_lock+0x30/0x38
__dw_hdmi_setup_rx_sense+0x28/0x98
dw_hdmi_setup_rx_sense+0x10/0x18
dw_hdmi_top_thread_irq+0x2c/0x50
irq_thread_fn+0x28/0x68
irq_thread+0x10c/0x1a0
kthread+0x128/0x130
ret_from_fork+0x10/0x18
Code: 34000964 d00050a2 51000484 9135c042 (f864d844)
---[ end trace 945641e1fbbc07da ]---
note: irq/32-dw_hdmi_[124] exited with preempt_count 1
genirq: exiting task "irq/32-dw_hdmi_" (124) is an active IRQ thread (irq 32)
Fixes: eea034af90 ("drm/bridge/synopsys: dw-hdmi: don't clobber drvdata")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1527673438-20643-1-git-send-email-narmstrong@baylibre.com
Some of the platform-specific stuff in rockchip_dp_poweron() needs to
happen before the generic code. Some needs to happen after. Let's
split the callback in two.
Specifically we can't start doing PSR work until _after_ the whole
controller is up, so don't set the enable until the end.
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[seanpaul added exynos change]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-23-enric.balletbo@collabora.com
There is a race between AUX CH bring-up and enabling bridge which will
cause link training to fail. To avoid hitting it, don't change psr state
while enabling the bridge.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[seanpaul fixed up the commit message a bit and renamed *_supported to *_enabled]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-4-enric.balletbo@collabora.com
If there is another bridge after analogix_dp, then the connector object
should not be created. This fixes following timeouts on Exynos5420-based
Chromebook2 Peach-PIT board during boot:
exynos-dp 145b0000.dp-controller: AUX CH cmd reply timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305085741.18896-4-m.szyprowski@samsung.com
The driver that instantiates the bridge should own the drvdata, as all
driver model callbacks (probe, remove, shutdown, PM ops, etc.) are also
owned by its driver struct. Moreover, storing two different pointer
types in driver data depending on driver initialization status is barely
a good practice and in fact has led to many bugs in this driver.
Let's clean up this mess and change Analogix entry points to simply
accept some opaque struct pointer, adjusting their users at the same
time to avoid breaking the compilation.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110162348.22765-2-thierry.escande@collabora.com
dw_hdmi shouldn't set drvdata since some drivers might need to store
it's own data there. Rework dw_hdmi in a way to return struct dw_hdmi
instead to store it in drvdata. This way drivers are responsible to
store and pass structure when needed.
Idea was taken from the following commit:
8242ecbd59 ("drm/bridge/synopsys: stop clobbering drvdata")
Cc: p.zabel@pengutronix.de
Cc: Laurent.pinchart@ideasonboard.com
Cc: hjc@rock-chips.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-6-jernej.skrabec@siol.net
Parts of PHY code could be useful also for custom PHYs. For example,
Allwinner A83T has custom PHY which is probably Synopsys gen2 PHY
with few additional memory mapped registers, so most of the Synopsys PHY
related code could be reused.
Functions exported here are actually not specific to Synopsys PHYs but
to DWC HDMI controller PHY interface. This means that even if the PHY is
completely custom, i.e. not designed by Synopsys, exported functions can
be useful.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-5-jernej.skrabec@siol.net
Bridge drivers/helpers shouldn't be clobbering the drvdata, since a
parent driver might need to own this. Instead, let's return our
'dw_mipi_dsi' object and have callers pass that back to us for removal.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171128010538.119114-1-briannorris@chromium.org
MHL specification defines Remote Control Protocol(RCP) to
send input events between MHL devices.
The driver now recognizes RCP messages and reacts to them
by reporting key events to input subsystem, allowing
a user to control a device using TV remote control.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Acked-by: Sean Young <sean@mess.org>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503565087-19730-1-git-send-email-m.purski@samsung.com
I need this to be able to apply the deferred fbdev setup patches, I
need the relevant prep work that landed through the drm-intel tree.
Also squash in conflict fixup from Laurent Pinchart.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The "supported input formats" table in dw_hdmi.h was incorrectly formatted,
using "+" signs where "|" needs to be. That, in turn, causes the PDF build
to fail.
Fixes: def23aa7e9 ("drm: bridge: dw-hdmi: Switch to V4L bus format and encodings")
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170623140013.0703107a@lwn.net
Now that we have a callback to check if bridge supports a given mode
we can use it in Synopsys Designware HDMI bridge so that we restrict
the number of probbed modes to the ones we can actually display.
Also, there is no need to use mode_fixup() callback as mode_valid()
will handle the mode validation.
NOTE: I also had to change the pdata declaration of mode_valid
custom callback so that the passed modes are const. I also changed
in the platforms I found. Not even compiled it though.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/3d8d449e4d13d2535fa292c75f5fa931de4a4fa8.1495720737.git.joabreu@synopsys.com
The HDMI TX controller support HPD and RXSENSE signaling from the PHY
via it's STAT0 PHY interface, but some vendor PHYs can manage these
signals independently from the controller, thus these STAT0 handling
should be moved to PHY specific operations and become optional.
The existing STAT0 HPD and RXSENSE handling code is refactored into
a supplementaty set of default PHY operations that are used automatically
when the platform glue doesn't provide its own operations.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491309119-24220-2-git-send-email-narmstrong@baylibre.com
Switch code to use the newly introduced V4L bus formats IDs instead of custom
defines. Also use the V4L encoding defines.
Some display pipelines can only provide non-RBG input pixels to the HDMI TX
Controller, this patch takes the pixel format from the plat_data if provided.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Synopsys Designware HDMI TX Controller does not enforce register
access on platforms instanciating it. The current driver supports two
different types of memory-mapped flat register access, but in order to
support the Amlogic Meson SoCs integration, and provide a more generic
way to handle all sorts of register mapping, switch the register access
to use the regmap infrastructure.
In the case of registers that are not flat memory-mapped or do not
conform to the current driver implementation, a regmap struct can be
given in the plat_data and be used at probe or bind.
Since the AHB audio driver is only available with direct memory access,
only allow the I2S audio driver to be registered is directly
memory-mapped.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-10-laurent.pinchart+renesas@ideasonboard.com
The device type isn't used anymore now that workarounds and PHY-specific
operations are performed based on version information read at runtime.
Remove it.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-9-laurent.pinchart+renesas@ideasonboard.com
The DWC HDMI TX controller interfaces with a companion PHY. While
Synopsys provides multiple standard PHYs, SoC vendors can also integrate
a custom PHY.
Modularize PHY configuration to support vendor PHYs through platform
data. The existing PHY configuration code was originally written to
support the DWC HDMI 3D TX PHY, and seems to be compatible with the DWC
MLP PHY. The HDMI 2.0 PHY will require a separate configuration
function.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-8-laurent.pinchart+renesas@ideasonboard.com
The HDMI TX controller support different PHYs whose programming
interface can vary significantly, especially with vendor PHYs that are
not provided by Synopsys. To support them, create a PHY operation
structure that can be provided by the platform glue layer. The existing
PHY handling code (limited to Synopsys PHY support) is refactored into a
set of default PHY operations that are used automatically when the
platform glue doesn't provide its own operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170305233615.11993-1-laurent.pinchart+renesas@ideasonboard.com
Add two simple functions that just take the drm_dp_aux from our struct
and calls the corresponding DP helpers with it.
v6: Pass to the DP helper the drm_crtc of the current connector (Sean Paul)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-4-tomeu.vizoso@collabora.com
As an option for drivers not based on the component framework, register
the bridge with the DRM core with the DRM bridge API. Existing drivers
based on dw_hdmi_bind() and dw_hdmi_unbind() are not affected as those
functions are preserved with their current behaviour.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-11-laurent.pinchart+renesas@ideasonboard.com
There's no need to duplicate identical code in multiple drivers (two at
the moment, one more to come soon). Move it to the dw-hdmi core where it
can be shared. If resource allocation ever becomes device-specific later
we'll always have the option of splitting it out again.
While it at pass the platform device to the bind function to avoid
having to cast struct device to struct platform_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-8-laurent.pinchart+renesas@ideasonboard.com
The master argument isn't used. The data argument, a void pointer, is
used by the bind function only where it's cast to a drm_device pointer,
which can easily be obtained from the encoder argument instead. Remove
them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-3-laurent.pinchart+renesas@ideasonboard.com
The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.
This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
It's better to pass the connector to platform driver in .get_modes()
callback, just like what the .get_modes() helper function designed.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
RK3399 and RK3288 shared the same eDP IP controller, only some light
difference with VOP configure and GRF configure.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.
But due to IC PHY layout mistaken, some chips need to flip this
bit(like RK3288), and unfortunately they didn't indicate in the
DP version register. That's why we have to make this little hack.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Rockchip have three clocks for dp controller, we leave pclk_edp
to analogix_dp driver control, and keep the sclk_edp_24m and
sclk_edp in platform driver.
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Here are some development updates for the Synopsis Designware HDMI driver,
which clean up some of the code, and start preparing to add audio support
to the driver. This series of patches are based on a couple of dependent
commits from the ALSA tree.
Briefly, the updates are:
- move comments which should have moved with the phy values to the IMX
part of the driver.
- clean up the phy configuration: to all lookups before starting to
program the phy.
- clean up the HDMI clock regenerator code
- use the drm_hdmi_avi_infoframe_from_display_mode() helper which allows
the code to be subsequently simplified
- remove the unused 'regmap' pointer in struct dw_hdmi
- use the bridge drm device rather than the connector (we're the bridge
code)
- remove private hsync/vsync/interlaced flags, getting them from the
DRM mode structure instead.
- implement interface functions to support audio - setting the audio
sample rate, and enabling the audio clocks.
- removal of broken pixel repetition support
- cleanup DVI vs HDMI sink handling
- enable audio only if connected device supports audio
- avoid double-enabling bridge in the sink path (once in mode_set, and
again in commit)
- rename mis-named dw_hdmi_phy_enable_power()
- fix bridge enable/disable handing, so a plug-in event doesn't
reconfigure the bridge if DRM has disabled the output
- fix from Vladimir Zapolskiy for the I2CM_ADDRESS macro name
These are primerily preparitory patches for the AHB audio driver and
the I2S audio driver (from Rockchip) for this IP.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: bridge/dw_hdmi: fix register I2CM_ADDRESS register name
drm: bridge/dw_hdmi: fix phy enable/disable handling
drm: bridge/dw_hdmi: rename dw_hdmi_phy_enable_power()
drm: bridge/dw_hdmi: avoid enabling interface in mode_set
drm: bridge/dw_hdmi: enable audio only if sink supports audio
drm: bridge/dw_hdmi: clean up HDMI vs DVI mode handling
drm: bridge/dw_hdmi: don't support any pixel doubled modes
drm: bridge/dw_hdmi: remove pixel repetition setting for all VICs
drm: bridge/dw_hdmi: introduce interfaces to enable and disable audio
drm: bridge/dw_hdmi: introduce interface to setting sample rate
drm: bridge/dw_hdmi: remove mhsyncpolarity/mvsyncpolarity/minterlaced
drm: bridge/dw_hdmi: use our own drm_device
drm: bridge/dw_hdmi: remove unused 'regmap' struct member
drm: bridge/dw_hdmi: simplify hdmi_config_AVI() a little
drm: bridge/dw_hdmi: use drm_hdmi_avi_infoframe_from_display_mode()
drm: bridge/dw_hdmi: clean up hdmi_set_clk_regenerator()
drm: bridge/dw_hdmi: clean up phy configuration
drm: imx/dw_hdmi: move phy comments
drm/edid: add function to help find SADs
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This header file declares prototypes of functions that are no longer
used. Remove this file and all references to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Because of iMX6 & Rockchip have differnet mpll config parameter,
the VLEVCTRL parameter would be different. In this case we should
separate VLEVCTRL setting from the common dw_hdmi driver, config
this parameter in platform driver(dw_hdmi-imx and dw_hdmi-rockchip)
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rockchip RK3288 hdmi is compatible with dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
