Pull Intel Quark SoC support from Ingo Molnar:
"This adds support for Intel Quark X1000 SoC boards, used in the low
power 32-bit x86 Intel Galileo microcontroller board intended for the
Arduino space.
There's been some preparatory core x86 patches for Quark CPU quirks
merged already, but this rounds it all up and adds Kconfig enablement.
It's a clean hardware enablement addition tree at this point"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/quark: Fix simple_return.cocci warnings
x86/intel/quark: Fix ptr_ret.cocci warnings
x86/intel/quark: Add Intel Quark platform support
x86/intel/quark: Add Isolated Memory Regions for Quark X1000
Pull misc x86 fixes from Ingo Molnar:
"This contains:
- EFI fixes
- a boot printout fix
- ASLR/kASLR fixes
- intel microcode driver fixes
- other misc fixes
Most of the linecount comes from an EFI revert"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/ASLR: Avoid PAGE_SIZE redefinition for UML subarch
x86/microcode/intel: Handle truncated microcode images more robustly
x86/microcode/intel: Guard against stack overflow in the loader
x86, mm/ASLR: Fix stack randomization on 64-bit systems
x86/mm/init: Fix incorrect page size in init_memory_mapping() printks
x86/mm/ASLR: Propagate base load address calculation
Documentation/x86: Fix path in zero-page.txt
x86/apic: Fix the devicetree build in certain configs
Revert "efi/libstub: Call get_memory_map() to obtain map and desc sizes"
x86/efi: Avoid triple faults during EFI mixed mode calls
Add Intel Quark platform support. Quark needs to pull down all
unlocked IMRs to ensure agreement with the EFI memory map post
boot.
This patch adds an entry in Kconfig for Quark as a platform and
makes IMR support mandatory if selected.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Andy Shevchenko <andy.schevchenko@gmail.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Cc: dvhart@infradead.org
Link: http://lkml.kernel.org/r/1422635379-12476-3-git-send-email-pure.logic@nexus-software.ie
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Intel's Quark X1000 SoC contains a set of registers called
Isolated Memory Regions. IMRs are accessed over the IOSF mailbox
interface. IMRs are areas carved out of memory that define
read/write access rights to the various system agents within the
Quark system. For a given agent in the system it is possible to
specify if that agent may read or write an area of memory
defined by an IMR with a granularity of 1 KiB.
Quark_SecureBootPRM_330234_001.pdf section 4.5 details the
concept of IMRs quark-x1000-datasheet.pdf section 12.7.4 details
the implementation of IMRs in silicon.
eSRAM flush, CPU Snoop write-only, CPU SMM Mode, CPU non-SMM
mode, RMU and PCIe Virtual Channels (VC0 and VC1) can have
individual read/write access masks applied to them for a given
memory region in Quark X1000. This enables IMRs to treat each
memory transaction type listed above on an individual basis and
to filter appropriately based on the IMR access mask for the
memory region. Quark supports eight IMRs.
Since all of the DMA capable SoC components in the X1000 are
mapped to VC0 it is possible to define sections of memory as
invalid for DMA write operations originating from Ethernet, USB,
SD and any other DMA capable south-cluster component on VC0.
Similarly it is possible to mark kernel memory as non-SMM mode
read/write only or to mark BIOS runtime memory as SMM mode
accessible only depending on the particular memory footprint on
a given system.
On an IMR violation Quark SoC X1000 systems are configured to
reset the system, so ensuring that the IMR memory map is
consistent with the EFI provided memory map is critical to
ensure no IMR violations reset the system.
The API for accessing IMRs is based on MTRR code but doesn't
provide a /proc or /sys interface to manipulate IMRs. Defining
the size and extent of IMRs is exclusively the domain of
in-kernel code.
Quark firmware sets up a series of locked IMRs around pieces of
memory that firmware owns such as ACPI runtime data. During boot
a series of unlocked IMRs are placed around items in memory to
guarantee no DMA modification of those items can take place.
Grub also places an unlocked IMR around the kernel boot params
data structure and compressed kernel image. It is necessary for
the kernel to tear down all unlocked IMRs in order to ensure
that the kernel's view of memory passed via the EFI memory map
is consistent with the IMR memory map. Without tearing down all
unlocked IMRs on boot transitory IMRs such as those used to
protect the compressed kernel image will cause IMR violations and system reboots.
The IMR init code tears down all unlocked IMRs and sets a
protective IMR around the kernel .text and .rodata as one
contiguous block. This sanitizes the IMR memory map with respect
to the EFI memory map and protects the read-only portions of the
kernel from unwarranted DMA access.
Tested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Andy Shevchenko <andy.schevchenko@gmail.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Cc: andy.shevchenko@gmail.com
Cc: dvhart@infradead.org
Link: http://lkml.kernel.org/r/1422635379-12476-2-git-send-email-pure.logic@nexus-software.ie
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtgkACgkQMUfUDdst+ykXbACg14oFAmeYjO9RsdIHPXBvKseO
47QAn0foy91bpNQ5UFOxWS5L6Fzj2ZND
=syx2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as
well. All have been in linux-next with no reported issues"
* tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: 8250: Fix UART_BUG_TXEN workaround
serial: driver for ETRAX FS UART
tty: remove unused variable sprop
serial: of-serial: fetch line number from DT
serial: samsung: earlycon support depends on CONFIG_SERIAL_SAMSUNG_CONSOLE
tty/serial: serial8250_set_divisor() can be static
tty/serial: Add Spreadtrum sc9836-uart driver support
Documentation: DT: Add bindings for Spreadtrum SoC Platform
serial: samsung: remove redundant interrupt enabling
tty: Remove external interface for tty_set_termios()
serial: omap: Fix RTS handling
serial: 8250_omap: Use UPSTAT_AUTORTS for RTS handling
serial: core: Rework hw-assisted flow control support
tty/serial: 8250_early: Add support for PXA UARTs
tty/serial: of_serial: add support for PXA/MMP uarts
tty/serial: of_serial: add DT alias ID handling
serial: 8250: Prevent concurrent updates to shadow registers
serial: 8250: Use canary to restart console after suspend
serial: 8250: Refactor XR17V35X divisor calculation
serial: 8250: Refactor divisor programming
...
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
* Unnecessary buffer size calculation and condition on the lenght
removed from intel_cacheinfo.c::show_shared_cpu_map_func().
* uv_nmi_nr_cpus_pr() got overly smart and implemented "..."
abbreviation if the output stretched over the predefined 1024 byte
buffer. Replaced with plain printk.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy pointed out that if an NMI or MCE is received while we're in the
middle of an EFI mixed mode call a triple fault will occur. This can
happen, for example, when issuing an EFI mixed mode call while running
perf.
The reason for the triple fault is that we execute the mixed mode call
in 32-bit mode with paging disabled but with 64-bit kernel IDT handlers
installed throughout the call.
At Andy's suggestion, stop playing the games we currently do at runtime,
such as disabling paging and installing a 32-bit GDT for __KERNEL_CS. We
can simply switch to the __KERNEL32_CS descriptor before invoking
firmware services, and run in compatibility mode. This way, if an
NMI/MCE does occur the kernel IDT handler will execute correctly, since
it'll jump to __KERNEL_CS automatically.
However, this change is only possible post-ExitBootServices(). Before
then the firmware "owns" the machine and expects for its 32-bit IDT
handlers to be left intact to service interrupts, etc.
So, we now need to distinguish between early boot and runtime
invocations of EFI services. During early boot, we need to restore the
GDT that the firmware expects to be present. We can only jump to the
__KERNEL32_CS code segment for mixed mode calls after ExitBootServices()
has been invoked.
A liberal sprinkling of comments in the thunking code should make the
differences in early and late environments more apparent.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
__FUNCTION__ hasn't been treated as a string literal since gcc 3.4, so
this only helps people who only test-compile using 3.3 (compiler-gcc3.h
barks at anything older than that). Besides, there are almost no
occurrences of __FUNCTION__ left in the tree.
[akpm@linux-foundation.org: convert remaining __FUNCTION__ references]
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel Moorestown platform support was removed few years ago. This is a follow
up which removes Moorestown specific code for the serial devices. It includes
mrst_max3110 and earlyprintk bits.
This was used on SFI (Medfield, Clovertrail) based platforms as well, though
new ones use normal serial interface for the console service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
Use helpers to access irq_cfg data structure associated with IRQ,
instead of accessing irq_data->chip_data directly. Later we can
rewrite those helpers to support hierarchy irqdomain.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414397531-28254-17-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename local APIC related functions in io_apic.c as apic_xxx() instead
of ioapic_xxx(), later they will be moved into separate file.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1414397531-28254-7-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull x86 platform changes from Ingo Molnar:
"A handful of numachip APIC driver updates/fixes, and two small SGI/UV
fixes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: numachip: APIC driver cleanups
x86: numachip: Elide self-IPI ICR polling
x86: numachip: Fix 16-bit APIC ID truncation
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: UV BAU: Increase maximum CPUs per socket/hub
x86: UV BAU: Avoid NULL pointer reference in ptc_seq_show
Pull EFI updates from Ingo Molnar:
"Changes in this cycle are:
- support module unload for efivarfs (Mathias Krause)
- another attempt at moving x86 to libstub taking advantage of the
__pure attribute (Ard Biesheuvel)
- add EFI runtime services section to ptdump (Mathias Krause)"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, ptdump: Add section for EFI runtime services
efi/x86: Move x86 back to libstub
efivarfs: Allow unloading when build as module
* Another attempt at moving x86 to libstub taking advantage of the
__pure attribute - Ard Biesheuvel
* Add EFI runtime services section to ptdump - Mathias Krause
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=he2O
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/efi
Pull EFI updates for v3.19 from Matt Fleming:
- Support module unload for efivarfs - Mathias Krause
- Another attempt at moving x86 to libstub taking advantage of the
__pure attribute - Ard Biesheuvel
- Add EFI runtime services section to ptdump - Mathias Krause
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In commit 3891a04aaf ("x86-64, espfix: Don't leak bits 31:16 of %esp
returning..") the "ESPFix Area" was added to the page table dump special
sections. That area, though, has a limited amount of entries printed.
The EFI runtime services are, unfortunately, located in-between the
espfix area and the high kernel memory mapping. Due to the enforced
limitation for the espfix area, the EFI mappings won't be printed in the
page table dump.
To make the ESP runtime service mappings visible again, provide them a
dedicated entry.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
In init_per_cpu(), when get_cpu_topology() fails, init_per_cpu_tunables()
is not called afterwards. This means that bau_control->statp is NULL.
If a user then reads /proc/sgi_uv/ptc_statistics ptc_seq_show() references
a NULL pointer. Therefore, since uv_bau_init calls set_bau_off when
init_per_cpu() fails, we add code that detects when the bau is off in
ptc_seq_show() to avoid referencing a NULL pointer.
Signed-off-by: James Custer <jcuster@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Link: http://lkml.kernel.org/r/1414952199-185319-2-git-send-email-jcuster@sgi.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 fixes from Ingo Molnar:
"Fixes from all around the place:
- hyper-V 32-bit PAE guest kernel fix
- two IRQ allocation fixes on certain x86 boards
- intel-mid boot crash fix
- intel-quark quirk
- /proc/interrupts duplicate irq chip name fix
- cma boot crash fix
- syscall audit fix
- boot crash fix with certain TSC configurations (seen on Qemu)
- smpboot.c build warning fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, pageattr: Prevent overflow in slow_virt_to_phys() for X86_PAE
ACPI, irq, x86: Return IRQ instead of GSI in mp_register_gsi()
x86, intel-mid: Create IRQs for APB timers and RTC timers
x86: Don't enable F00F workaround on Intel Quark processors
x86/irq: Fix XT-PIC-XT-PIC in /proc/interrupts
x86, cma: Reserve DMA contiguous area after initmem_init()
i386/audit: stop scribbling on the stack frame
x86, apic: Handle a bad TSC more gracefully
x86: ACPI: Do not translate GSI number if IOAPIC is disabled
x86/smpboot: Move data structure to its primary usage scope
Intel MID platforms has no legacy interrupts, so no IRQ descriptors
preallocated. We need to call mp_map_gsi_to_irq() to create IRQ
descriptors for APB timers and RTC timers, otherwise it may cause
invalid memory access as:
[ 0.116839] BUG: unable to handle kernel NULL pointer dereference at
0000003a
[ 0.123803] IP: [<c1071c0e>] setup_irq+0xf/0x4d
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: <stable@vger.kernel.org> # 3.17
Link: http://lkml.kernel.org/r/1414387308-27148-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
function, where an architecture can override it by providing a strong
version.
Some header file declarations included the "weak" attribute. That's
error-prone because it causes every implementation to be weak, with no
strong version at all, and the linker chooses one based on link order.
What we want is the "weak" attribute only on the *definition* of the
default implementation. These changes remove "weak" from the declarations,
leaving it on the default definitions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=P4fi
-----END PGP SIGNATURE-----
Merge tag 'remove-weak-declarations' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull weak function declaration removal from Bjorn Helgaas:
"The "weak" attribute is commonly used for the default version of a
function, where an architecture can override it by providing a strong
version.
Some header file declarations included the "weak" attribute. That's
error-prone because it causes every implementation to be weak, with no
strong version at all, and the linker chooses one based on link order.
What we want is the "weak" attribute only on the *definition* of the
default implementation. These changes remove "weak" from the
declarations, leaving it on the default definitions"
* tag 'remove-weak-declarations' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
uprobes: Remove "weak" from function declarations
memory-hotplug: Remove "weak" from memory_block_size_bytes() declaration
kgdb: Remove "weak" from kgdb_arch_pc() declaration
ARC: kgdb: generic kgdb_arch_pc() suffices
vmcore: Remove "weak" from function declarations
clocksource: Remove "weak" from clocksource_default_clock() declaration
x86, intel-mid: Remove "weak" from function declarations
audit: Remove "weak" from audit_classify_compat_syscall() declaration
Pull x86 EFI updates from Peter Anvin:
"This patchset falls under the "maintainers that grovel" clause in the
v3.18-rc1 announcement. We had intended to push it late in the merge
window since we got it into the -tip tree relatively late.
Many of these are relatively simple things, but there are a couple of
key bits, especially Ard's and Matt's patches"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
rtc: Disable EFI rtc for x86
efi: rtc-efi: Export platform:rtc-efi as module alias
efi: Delete the in_nmi() conditional runtime locking
efi: Provide a non-blocking SetVariable() operation
x86/efi: Adding efi_printks on memory allocationa and pci.reads
x86/efi: Mark initialization code as such
x86/efi: Update comment regarding required phys mapped EFI services
x86/efi: Unexport add_efi_memmap variable
x86/efi: Remove unused efi_call* macros
efi: Resolve some shadow warnings
arm64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
ia64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
x86: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
efi: Introduce efi_md_typeattr_format()
efi: Add macro for EFI_MEMORY_UCE memory attribute
x86/efi: Clear EFI_RUNTIME_SERVICES if failing to enter virtual mode
arm64/efi: Do not enter virtual mode if booting with efi=noruntime or noefi
arm64/efi: uefi_init error handling fix
efi: Add kernel param efi=noruntime
lib: Add a generic cmdline parse function parse_option_str
...
For the following interfaces:
get_penwell_ops()
get_cloverview_ops()
get_tangier_ops()
there is only one implementation, so they do not need to be marked "weak".
Remove the "weak" attribute from their declarations.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
CC: David Cohen <david.a.cohen@linux.intel.com>
CC: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
CC: x86@kernel.org
The 32 bit and 64 bit implementations differ in their __init annotations
for some functions referenced from the common EFI code. Namely, the 32
bit variant is missing some of the __init annotations the 64 bit variant
has.
To solve the colliding annotations, mark the corresponding functions in
efi_32.c as initialization code, too -- as it is such.
Actually, quite a few more functions are only used during initialization
and therefore can be marked __init. They are therefore annotated, too.
Also add the __init annotation to the prototypes in the efi.h header so
users of those functions will see it's meant as initialization code
only.
This patch also fixes the "prelog" typo. ("prologue" / "epilogue" might
be more appropriate but this is C code after all, not an opera! :D)
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Commit 3f4a7836e3 ("x86/efi: Rip out phys_efi_get_time()") left
set_virtual_address_map as the only runtime service needed with a
phys mapping but missed to update the preceding comment. Fix that.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This variable was accidentally exported, even though it's only used in
this compilation unit and only during initialization.
Remove the bogus export, make the variable static instead and mark it
as __initdata.
Fixes: 200001eb14 ("x86 boot: only pick up additional EFI memmap...")
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
If enter virtual mode failed due to some reason other than the efi call
the EFI_RUNTIME_SERVICES bit in efi.flags should be cleared thus users
of efi runtime services can check the bit and handle the case instead of
assume efi runtime is ok.
Per Matt, if efi call SetVirtualAddressMap fails we will be not sure
it's safe to make any assumptions about the state of the system. So
kernel panics instead of clears EFI_RUNTIME_SERVICES bit.
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
noefi kernel param means actually disabling efi runtime, Per suggestion
from Leif Lindholm efi=noruntime should be better. But since noefi is
already used in X86 thus just adding another param efi=noruntime for
same purpose.
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
There should be a generic function to parse params like a=b,c
Adding parse_option_str in lib/cmdline.c which will return true
if there's specified option set in the params.
Also updated efi=old_map parsing code to use the new function
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
noefi param can be used for arches other than X86 later, thus move it
out of x86 platform code.
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Gracefully handle failures to allocate memory for the image, which might
be arbitrarily large.
efi_bgrt_init can fail in various ways as well, usually because the
BIOS-provided BGRT structure does not match expectations. Add
appropriate error messages rather than failing silently.
Reported-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81321
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
We need a way to customize the behaviour of the EFI boot stub, in
particular, we need a way to disable the "chunking" workaround, used
when reading files from the EFI System Partition.
One of my machines doesn't cope well when reading files in 1MB chunks to
a buffer above the 4GB mark - it appears that the "chunking" bug
workaround triggers another firmware bug. This was only discovered with
commit 4bf7111f50 ("x86/efi: Support initrd loaded above 4G"), and
that commit is perfectly valid. The symptom I observed was a corrupt
initrd rather than any kind of crash.
efi= is now used to specify EFI parameters in two very different
execution environments, the EFI boot stub and during kernel boot.
There is also a slight performance optimization by enabling efi=nochunk,
but that's offset by the fact that you're more likely to run into
firmware issues, at least on x86. This is the rationale behind leaving
the workaround enabled by default.
Also provide some documentation for EFI_READ_CHUNK_SIZE and why we're
using the current value of 1MB.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Roy Franz <roy.franz@linaro.org>
Cc: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull x86/apic updates from Thomas Gleixner:
"This is a major overhaul to the x86 apic subsystem consisting of the
following parts:
- Remove obsolete APIC driver abstractions (David Rientjes)
- Use the irqdomain facilities to dynamically allocate IRQs for
IOAPICs. This is a prerequisite to enable IOAPIC hotplug support,
and it also frees up wasted vectors (Jiang Liu)
- Misc fixlets.
Despite the hickup in Ingos previous pull request - caused by the
missing fixup for the suspend/resume issue reported by Borislav - I
strongly recommend that this update finds its way into 3.17. Some
history for you:
This is preparatory work for physical IOAPIC hotplug. The first
attempt to support this was done by Yinghai and I shot it down because
it just added another layer of obscurity and complexity to the already
existing mess without tackling the underlying shortcomings of the
current implementation.
After quite some on- and offlist discussions, I requested that the
design of this functionality must use generic infrastructure, i.e.
irq domains, which provide all the mechanisms to dynamically map linux
interrupt numbers to physical interrupts.
Jiang picked up the idea and did a great job of consolidating the
existing interfaces to manage the x86 (IOAPIC) interrupt system by
utilizing irq domains.
The testing in tip, Linux-next and inside of Intel on various machines
did not unearth any oddities until Borislav exposed it to one of his
oddball machines. The issue was resolved quickly, but unfortunately
the fix fell through the cracks and did not hit the tip tree before
Ingo sent the pull request. Not entirely Ingos fault, I also assumed
that the fix was already merged when Ingo asked me whether he could
send it.
Nevertheless this work has a proper design, has undergone several
rounds of review and the final fallout after applying it to tip and
integrating it into Linux-next has been more than moderate. It's the
ground work not only for IOAPIC hotplug, it will also allow us to move
the lowlevel vector allocation into the irqdomain hierarchy, which
will benefit other architectures as well. Patches are posted already,
but they are on hold for two weeks, see below.
I really appreciate the competence and responsiveness Jiang has shown
in course of this endavour. So I'm sure that any fallout of this will
be addressed in a timely manner.
FYI, I'm vanishing for 2 weeks into my annual kids summer camp kitchen
duty^Wvacation, while you folks are drooling at KS/LinuxCon :) But HPA
will have a look at the hopefully zero fallout until I'm back"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
x86, irq, PCI: Keep IRQ assignment for PCI devices during suspend/hibernation
x86/apic/vsmp: Make is_vsmp_box() static
x86, apic: Remove enable_apic_mode callback
x86, apic: Remove setup_portio_remap callback
x86, apic: Remove multi_timer_check callback
x86, apic: Replace noop_check_apicid_used
x86, apic: Remove check_apicid_present callback
x86, apic: Remove mps_oem_check callback
x86, apic: Remove smp_callin_clear_local_apic callback
x86, apic: Replace trampoline physical addresses with defaults
x86, apic: Remove x86_32_numa_cpu_node callback
x86: intel-mid: Use the new io_apic interfaces
x86, vsmp: Remove is_vsmp_box() from apic_is_clustered_box()
x86, irq: Clean up irqdomain transition code
x86, irq, devicetree: Release IOAPIC pin when PCI device is disabled
x86, irq, SFI: Release IOAPIC pin when PCI device is disabled
x86, irq, mpparse: Release IOAPIC pin when PCI device is disabled
x86, irq, ACPI: Release IOAPIC pin when PCI device is disabled
x86, irq: Introduce helper functions to release IOAPIC pin
x86, irq: Simplify the way to handle ISA IRQ
...
Pull x86 UV TLB update from Ingo Molnar:
"UV TLB shootdown logic updates for version of the UV architecture"
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/uv: Update the UV3 TLB shootdown logic
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle are:
- Intel SOC driver updates, by Aubrey Li.
- TS5500 platform updates, by Vivien Didelot"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pmc_atom: Silence shift wrapping warnings in pmc_sleep_tmr_show()
x86/pmc_atom: Expose PMC device state and platform sleep state
x86/pmc_atom: Eisable a few S0ix wake up events for S0ix residency
x86/platform: New Intel Atom SOC power management controller driver
x86/platform/ts5500: Add support for TS-5400 boards
x86/platform/ts5500: Add a 'name' sysfs attribute
x86/platform/ts5500: Use the DEVICE_ATTR_RO() macro
efi_set_rtc_mmss() is never used to set RTC due to bugs found
on many EFI platforms. It is set directly by mach_set_rtc_mmss().
Hence, remove unused efi_set_rtc_mmss() function.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Remove redundant set_bit(EFI_MEMMAP, &efi.flags) call.
It is executed earlier in efi_memmap_init().
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
