Since not all platforms are using the same offset 0x10 in
musb_save/restore_context() eg Blackfin the offset is 0x40,
Change the indexed address to direct.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB stack maps the buffer for DMA if the controller supports DMA.
MUSB controller can perform DMA as well as PIO transfers.
The buffer needs to be unmapped before CPU can perform
PIO data transfers.
Export unmap_urb_for_dma() so that drivers can perform
the DMA unmapping in a sane way.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB's DMA controller max channel length was set to 64k.
Transfer length greater than this max value is being truncated.
Signed-off-by: Anil Shetty <anil@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch has been tested OK on beagle B5 board and
use usbtest #15 and #16 as testcase.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enabling CONFIG_USB_MUSB_DEBUG option causes -DDEBUG to be added to gcc's
command line, however the DBG() macro doesn't depend on DEBUG, so that the
debugging messages get printed regardless of the option, and I don't think
that this was intended. Get rid of otherwise unused xprintk() macro and make
DBG() macro directly call pr_debug() which only results in the actual code
generated if DEBUG is defined.
This change makes musb_hdrc.o ~30% less in size with CONFIG_USB_MUSB_DEBUG
disabled (in host mode).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the memory leak on disconnecting the device.
In addition, it fixes some messages corrupted by incorrect encoding.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This assigns the minor number 192 to the yurex driver.
We also fix up the previous usb minor number entry, it was wrong.
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Meywa-Denki/Kayac YUREX is a leg-shakes sensor device.
See http://bbu.kayac.com/en/about/ for further information.
This driver support read/write the leg-shakes counter in the device
via a device file /dev/yurex[0-9]*.
[minor coding style cleanups fixed by gregkh]
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit changes storage_common.c and file_storage.c to
reuse definitions from linux/usb/storage.h header file.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Attached SCSI is a new protocol specified jointly by the SCSI T10
committee and the USB Implementors Forum.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
[mina86@mina86.com: updated to use new USB_ prefix]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The libusual header file is hard to use from code that isn't part
of libusual. As the comment suggests, these definitions are moved to
their own header file, paralleling other USB classes.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
[mina86@mina86.com: updated to use USB_ prefix and added #include guard]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
index 0000000..d7fc910
This commit changes prefix for some of the USB mass storage
class related macros (ie. USB_SC_ for subclass and USB_PR_
for class).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch to qcserial.c enables the Diagnostics Monitor
and NMEA GPS ports on Qualcomm Gobi 2000 devices.
A Gobi 2000 device will provide 3 serial ports:
# /dev/ttyUSB0 -> Diagnostics
# /dev/ttyUSB1 -> 3G Modem
# /dev/ttyUSB2 -> NMEA GPS port
* The Diagnostics Monitor uses Qualcomm's DM protocol; I used
libqcdm (ModemManager) to talk to it, found it working, but at
least DM commands 12 and 64 are not implemented on my device
(Gobi 2000 built into Thinkpad x100e).
* Functionality of the 3G Modem port remains unchanged.
* The GPS port and how to enable it has been confirmed now in the
Gobi 3000 source code at:
https://www.codeaurora.org/patches/quic/gobi/
Enable/disable GPS via:
echo "\$GPS_START" > /dev/ttyUSB2
# use GPS
echo "\$GPS_STOP" > /dev/ttyUSB2
Signed-off-by: Matthias G. Eckermann <mge@arcor.de>
In usb_cdc_ncm_dpe32 the fields are 32 bit long and according
to usb style (hungarian notation) should be called dwDatagramIndex
and dwDatagramLength (see CDC NCM subclass spec, 3.3.2). Actually,
they were called wDatagramIndex, wDatagramLength.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 6a1a82df91.
RTS and DTR should not be modified based on CRTSCTS when calling
set_termios.
Modem control lines are raised at port open by the tty layer and should stay
raised regardless of whether hardware flow control is enabled or not.
This is in conformance with the way serial ports work today and many
applications depend on this behaviour to be able to talk to hardware
implementing hardware flow control (without the applications actually using
it).
Hardware which expects different behaviour on these lines can always
use TIOCMSET/TIOCMBI[SC] after port open to change them.
Reported-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Dave Mielke <dave@mielke.cc>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make a dedicated structure for datagram pointer entry. There is no
explicit declaration in the spec, but it's used by the host
implementation and makes the structure more clear.
Add some missed constants from the spec
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 65e0b49910.
Since the host and gadget implementations are different, there is
no common code for the file, remove for now.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some typos were in the initial commit, make the spelling
according to the spec.
Add some more comments.
Also change constant names according to the style of the rest
of the file
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, adds to the option driver the Onda Communication
(http://www.ondacommunication.com) vendor id, and the MT825UP modem
device id.
Note that many variants of this same device are being release here in
Italy (at least one or two per telephony operator).
These devices are perfectly equivalent except for some predefined
settings (which can be changed of course).
It should be noted that most ONDA devices are allready supported (they
used other vendor's ids in the past). The patch seems working fine here,
and the rest of the driver seems uninfluenced.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The un-registration of OHCI driver was not done in the ohci_hcd_mod_exit
function. This was affecting rmmod command not to work for OMAP3
platforms. The platform driver un-registration for OMAP3 platforms is
perfomed while removing the OHCI module from kernel.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for Accesio USB to Serial adapters, which are built around
FTDI FT232 UARTs. Tested with the Accesio USB-COM-4SM.
Signed-off-by: Rich Mattes <richmattes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The /sys/kernel/debug/usb/devices file doesn't know about Wireless or
SuperSpeed USB. This patch (as1416b) teaches it, and updates the
Documentation/usb/proc_sub_info.txt file accordingly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Vrabel <david.vrabel@csr.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are lots of ZTE USB id's currently not covered by usb/serial. Adds them,
to allow those devices to work properly on Linux.
While here, put the USB ID's for 0x2002/0x2003 at the sorted order.
This patch is based on zte.c file found on MF645.
PS.: The ZTE driver is commenting the USB ID for 0x0053. It also adds, commented,
an USB ID for 0x0026.
Not sure why, but I think that 0053 is used by their devices in storage mode only.
So, I opted to keep the comment on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile error on usb/host/isp1362-hcd:
drivers/usb/host/isp1362-hcd.c: In function ‘isp1362_hub_control’:
drivers/usb/host/isp1362-hcd.c:1680: error: ‘ohci’ undeclared (first use in this function)
The problem is when the CONFIG_USB_OTG option is enabled.
ohci variable is never declared and there isn't any CONFIG_USB_OTG dependent code
besides the portion defined in isp1362_hub_control.
So I think that maybe USB OTG support is not needed/supported.
This patch removes the CONFIG_USB_OTG dependent block so the driver can compile cleanly.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The composite gadget will OOPS if the host sends a control request
targetted to an interface of an un-configured composite device. This patch
prevents this.
The OOPS was observed during WHQL USB CV tests. With this patch, the device
STALLs as per requirement.
Failing test case: From host do the following. I used libusb-1.0
1) Set configuration to zero.
libusb_control_transfer(device_handle,
0, /* standard OUT */
0x9, /* setConfiguration */
0, 0, NULL, 0, 0);
2) Query current configuratioan.
libusb_control_transfer(device_handle,
0x80, /* standard IN*/
0x8, /* getConfiguration */
0, 0, data, 1, 0);
3) Send the non-standard ctrl transfer targetted to interface
libusb_control_transfer(device_handle,
0x81, /* standard IN to interface*/
0x6, /* getDescriptor */
0x2300, 0, data, 0x12, 0);
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Cc: stable <stable@kernel.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Robert Lukassen <robert.lukassen@tomtom.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets. When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports. This prevents attached devices from going
to low power. Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.
The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled. However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.
The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware. As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The protocol code is set 00 in IAD and it's set to 01 in ACM control
interface descriptor in f_acm.c file. Due to this, windows is unable to
install the modem(ACM) driver based on class-subclass-protocol matching.
This patch corrects the protocol code in ACM IAD to the same as in
acm_control_interface_desc protocol code.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile warning due a possible uninitialized variable
This patch solves the issue initializing the variable
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <damm@opensource.se>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updated Kconfig for langwell otg transceiver driver.
Add ipc driver(INTEL_SCU_IPC) as a dependency. Driver version is
updated too.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds one new header file for the common data structure used in
Intel Penwell/Langwell MID Platform OTG Transceiver drivers. After switched
to the common data structure, Langwell/Penwell OTG Transceiver driver will
provide an unified interface to host/client driver.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "mutex" ftdi->sw_lock is used as a lock and a completion. Convert
it to a real semaphore which allows both.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.
Make ehci_halt a nop if the controller is not in host mode (otherwise it
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt
knows we are a tdi device.
Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset
Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset
PS : now we handle correctly the device -> host transition.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's spelled "Function Filesystem" / "FunctionFS". This patch
fixes some typos (FunctioFS->FunctionFS, Funcion->Function,
funcion->function, redundant "as") in the Kconfig description of
USB_FUNCTIONFS*.
Signed-off-by: Michael Prokop <mika@grml.org>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1413) changes g_file_storage to avoid generating a bogus
automatic serial-number string descriptor. If the user doesn't provide
a valid serial number via a module parameter then a warning is logged
and the gadget won't have any serial string descriptor at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
CC: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit f661c6f8c6 adds a check of the pipe type if
CONFIG_USB_DEBUG is enabled, but it doesn't output anything if this scenario
occurs.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The same expression is tested twice and the result is the same each time.
Instead test for use_dma_ppb as in the test above.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The __ref* tags may have been confusing for new kernel
developers (I was confused by them for sure) so adding a few
more sentences to comment to clear things up for people who
see those for the first time.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the configuration structure.
This fixes many section mismatches reported by modpost.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: updated for -next]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the composite driver structure.
This fixes many section mismatches reported by modpost.
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To accomplish this the function to register a gadget driver takes the bind
function as a second argument. To make things clearer rename the function
to resemble platform_driver_probe.
This fixes many section mismatches like
WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in
reference from the variable printer_driver to the function
.init.text:printer_bind()
The variable printer_driver references
the function __init printer_bind()
All callers are fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: added dbgp]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>