of_match_device could return NULL, and so cause a NULL pointer
dereference later at line 199:
priv->flags = of_id->data;
Reported-by: coverity (CID 1324140)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now GPIO syscon driver produces bunch of warnings during the
boot of Kesytone 2 SoCs:
gpio-syscon soc:keystone_dsp_gpio@02620240: can't read the dir register offset!
gpio-syscon soc:keystone_dsp_gpio@2620244: can't read the dir register offset!
This message unintentionally was added using dev_err(), but its
actual log level is debug, because third cell of "ti,syscon-dev" is
optional.
Hence change it to dev_dbg() as it should be.
This patch fixes commit:
5a3e3f8 ("gpio: syscon: retriave syscon node and regs offsets from dt")
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Keystone SOCs, ARM host can send interrupts to DSP cores using the
DSP GPIO controller IP. Each DSP GPIO controller provides 28 IRQ signals for
each DSP core. This is one of the component used by the IPC mechanism used
on Keystone SOCs.
Keystone 2 DSP GPIO controller has specific features:
- each GPIO can be configured only as output pin;
- setting GPIO value to 1 causes IRQ generation on target DSP core;
- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still
pending.
This patch updates gpio-syscon driver to be reused by Keystone 2 SoCs,
because the Keystone 2 DSP GPIO controller is controlled through Syscon
devices and, as requested by Linus Walleij, such kind of GPIO controllers
should be integrated with drivers/gpio/gpio-syscon.c driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds handling of new "gpio,syscon-dev" DT property,
which allows to specify syscon node and data/direction registers
offsets in DT.
"gpio,syscon-dev" has following format:
gpio,syscon-dev = <&syscon_dev data_reg_offset [direction_reg_offset]>;
where
- syscon_dev - phandle on syscon node
- data_reg_offset - offset of data register (in bytes)
- direction_reg_offset - offset of dirrection register (optional, in bytes)
for example:
gpio,syscon-dev = <&devctrl 0x254>;
In such way, the support of multiple Syscon GPIO devices is added.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs (like Keystone) may require to perform special
sequence of operations to assign output GPIO value, so default
implementation of .set() callback from gpio-syscon driver
can't be used.
Hence, add optional, SoC specific callback to assign output
gpio value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SYSCON driver was designed for using memory areas (registers)
that are used in several subsystems. There are systems (CPUs)
which use bits in one register for various purposes and thus
should be handled by various kernel subsystems. This driver
allows you to use the individual SYSCON bits as GPIOs.
ARM CLPS711X SYSFLG1 input lines has been added as first user
of this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
