Currently the bridge multicast snooping feature periodically issues
IPv6 general multicast listener queries to sense the absence of a
listener.
For this, it uses :: as its source address - however RFC 2710 requires:
"To be valid, the Query message MUST come from a link-local IPv6 Source
Address". Current Linux kernel versions seem to follow this requirement
and ignore our bogus MLD queries.
With this commit a link local address from the bridge interface is being
used to issue the MLD query, resulting in other Linux devices which are
multicast listeners in the network to respond with a MLD response (which
was not the case before).
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Map the IPv6 header's destination multicast address to an ethernet
source address instead of the MLD queries multicast address.
For instance for a general MLD query (multicast address in the MLD query
set to ::), this would wrongly be mapped to 33:33:00:00:00:00, although
an MLD queries destination MAC should always be 33:33:00:00:00:01 which
matches the IPv6 header's multicast destination ff02::1.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the multicast bridge snooping support is not active for
link local multicast. I assume this has been done to leave
important multicast data untouched, like IPv6 Neighborhood Discovery.
In larger, bridged, local networks it could however be desirable to
optimize for instance local multicast audio/video streaming too.
With the transient flag in IPv6 multicast addresses we have an easy
way to optimize such multimedia traffic without tempering with the
high priority multicast data from well-known addresses.
This patch alters the multicast bridge snooping for IPv6, to take
effect for transient multicast addresses instead of non-link-local
addresses.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nsrcs number is 2 Byte wide, therefore we need to call ntohs()
before using it.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We actually want a pointer to the grec_nsrcr and not the following
field. Otherwise we can get very high values for *nsrcs as the first two
bytes of the IPv6 multicast address are being used instead, leading to
a failing pskb_may_pull() which results in MLDv2 reports not being
parsed.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol type for IPv6 entries in the hash table for multicast
bridge snooping is falsely set to ETH_P_IP, marking it as an IPv4
address, instead of setting it to ETH_P_IPV6, which results in negative
look-ups in the hash table later.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct tmp is copied from userspace. It is not checked whether the "name"
field is NULL terminated. This may lead to buffer overflow and passing
contents of kernel stack as a module name to try_then_request_module() and,
consequently, to modprobe commandline. It would be seen by all userspace
processes.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
As it turns out we never need to walk through the list of multicast
groups subscribed by the bridge interface itself (the only time we'd
want to do that is when we shut down the bridge, in which case we
simply walk through all multicast groups), we don't really need to
keep an hlist for mp->mglist.
This means that we can replace it with just a single bit to indicate
whether the bridge interface is subscribed to a group.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of spots where we are supposed to modify the port
group timer (p->timer) we instead modify the bridge interface
group timer (mp->timer).
The effect of this is mostly harmless. However, it can cause
port subscriptions to be longer than they should be, thus making
snooping less effective.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list mp->mglist is used to indicate whether a multicast group
is active on the bridge interface itself as opposed to one of the
constituent interfaces in the bridge.
Unfortunately the operation that adds the mp->mglist node to the
list neglected to check whether it has already been added. This
leads to list corruption in the form of nodes pointing to itself.
Normally this would be quite obvious as it would cause an infinite
loop when walking the list. However, as this list is never actually
walked (which means that we don't really need it, I'll get rid of
it in a subsequent patch), this instead is hidden until we perform
a delete operation on the affected nodes.
As the same node may now be pointed to by more than one node, the
delete operations can then cause modification of freed memory.
This was observed in practice to cause corruption in 512-byte slabs,
most commonly leading to crashes in jbd2.
Thanks to Josef Bacik for pointing me in the right direction.
Reported-by: Ian Page Hands <ihands@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fdb_create() puts a new fdb into hash with only addr set. This is
not good, since there are callers, that search the hash w/o the lock
and access all the other its fields.
Applies to current netdev tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce printk() levels to KERN_INFO in netdev_fix_features() as this will
be used by ethtool and might spam dmesg unnecessarily.
This converts the function to use netdev_info() instead of plain printk().
As a side effect, bonding and bridge devices will now log dropped features
on every slave device change.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.
Occurences found by `grep -r` on net/, drivers/net, include/
[ Move features and vlan_features next to each other in
struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid adding a new match revision icmp type/code are stored
in the sport/dport area.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Holger Eitzenberger <holger@eitzenberger.org>
Reviewed-by: Bart De Schuymer<bdschuym@pandora.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
One iptables invocation with 135000 rules takes 35 seconds of cpu time
on a recent server, using a 32bit distro and a 64bit kernel.
We eventually trigger NMI/RCU watchdog.
INFO: rcu_sched_state detected stall on CPU 3 (t=6000 jiffies)
COMPAT mode has quadratic behavior and consume 16 bytes of memory per
rule.
Switch the xt_compat algos to use an array instead of list, and use a
binary search to locate an offset in the sorted array.
This halves memory need (8 bytes per rule), and removes quadratic
behavior [ O(N*N) -> O(N*log2(N)) ]
Time of iptables goes from 35 s to 150 ms.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since nf_bridge_maybe_copy_header() may change the length of skb,
we should check the length of skb after it to handle the ppoe skbs.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/bridge//br_stp_if.c:148:66: warning: conversion of
net/bridge//br_stp_if.c:148:66: int to
net/bridge//br_stp_if.c:148:66: int enum umh_wait
net/bridge//netfilter/ebtables.c:1150:30: warning: Using plain integer as NULL pointer
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bf9ae5386b
(llc: use dev_hard_header) removed the
skb_reset_mac_header call from llc_mac_hdr_init.
This seems fine itself, but br_send_bpdu() invokes ebtables LOCAL_OUT.
We oops in ebt_basic_match() because it assumes eth_hdr(skb) returns
a meaningful result.
Cc: acme@ghostprotocols.net
References: https://bugzilla.kernel.org/show_bug.cgi?id=24532
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a missing ntohs() for bridge IPv6 multicast snooping.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_pre_routing functions in bridging have collected two
distinct ways of returning NF_DROP over the years, inline and
via goto. There is no reason for preferring either one.
So this patch arbitrarily picks the inline variant and converts
the all the gotos.
Also removes a redundant comment.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If br_multicast_new_group returns NULL, we would return 0 (no error) to
the caller of br_multicast_add_group, which is not what we want. Instead
br_multicast_new_group should return ERR_PTR(-ENOMEM) in this case.
Also propagate the error number returned by br_mdb_rehash properly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to hide all direct accesses, especially writes,
to dst_entry metrics values.
This will allow us to:
1) More easily change how the metrics are stored.
2) Implement COW for metrics.
In particular this will help us put metrics into the inetpeer
cache if that is what we end up doing. We can make the _metrics
member a pointer instead of an array, initially have it point
at the read-only metrics in the FIB, and then on the first set
grab an inetpeer entry and point the _metrics member there.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_port_get() renamed to br_port_get_rtnl() to make clear RTNL is held.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro br_port_exists() is not enough protection when only
RCU is being used. There is a tiny race where other CPU has cleared port
handler hook, but is bridge port flag might still be set.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add br_should_route_hook_t typedef, this is the only way we can
get a clean RCU implementation for function pointer.
Move route_hook to location where it is used.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add modern __rcu annotatations to bridge multicast table.
Use newer hlist macros to avoid direct access to hlist internals.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all frames sent to reserved group MAC addresses (01:80:c2:00:00:00 to
01:80:c2:00:00:0f) be forwarded if STP is disabled. This enables
forwarding EAPOL frames, among other things.
Signed-off-by: Benjamin Poirier <benjamin.poirier@polymtl.ca>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If some of the underlying devices support it, enable vlan offload on
transmit for bridge devices. This allows senders to take advantage of the
hardware support, similar to other forms of acceleration.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An upcoming commit will allow packets with hardware vlan acceleration
information to be passed though more parts of the network stack, including
packets trunked through the bridge. This adds support for matching and
filtering those packets through ebtables.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct dst_ops tracks number of allocated dst in an atomic_t field,
subject to high cache line contention in stress workload.
Switch to a percpu_counter, to reduce number of time we need to dirty a
central location. Place it on a separate cache line to avoid dirtying
read only fields.
Stress test :
(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE, SLUB/NUMA)
Before:
real 0m51.179s
user 0m15.329s
sys 10m15.942s
After:
real 0m45.570s
user 0m15.525s
sys 9m56.669s
With a small reordering of struct neighbour fields, subject of a
following patch, (to separate refcnt from other read mostly fields)
real 0m41.841s
user 0m15.261s
sys 8m45.949s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Related dicussion here : http://lkml.org/lkml/2010/9/3/16
Introduce a function br_parse_ip_options that will audit the
skb and possibly refill IP options before a packet enters the
IP stack. If no options are present, the function will zero out
the skb cb area so that it is not misinterpreted as options by some
unsuspecting IP layer routine. If packet consistency fails, drop it.
Signed-off-by: Bandan Das <bandan.das@stratus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar vain to commit 17762060c2
("bridge: Clear IPCB before possible entry into IP stack")
Any time we call into the IP stack we have to make sure the state
there is as expected by the ipv4 code.
With help from Eric Dumazet and Herbert Xu.
Reported-by: Bandan Das <bandan.das@stratus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bridge port is offline, don't call ethtool to query speed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The carrier check is not called from work queue in current code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_bridge_alloc() always reset the skb->nf_bridge, so we should always
put the old one.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at using netdev_rx_handler_register for openvswitch Jesse
Gross suggested that an unlikely() might be worthwhile in that code.
I'm interested to see if its appropriate for the bridge code.
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently you cannot disable multicast snooping while a device is
down. There is no good reason for this restriction and this patch
removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the bridge TX path we're leaking an skb when br_multicast_rcv
returns an error.
Reported-by: David Lamparter <equinox@diac24.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long ago, when bridge was converted to RCU, rcu lock was equivalent
to having preempt disabled. RCU has changed a lot since then and
bridge code was still assuming the since transmit was called with
bottom half disabled, it was RCU safe.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new netpoll code in bridging contains use-after-free bugs
that are non-trivial to fix.
This patch fixes this by removing the code that uses skbs after
they're freed.
As a consequence, this means that we can no longer call bridge
from the netpoll path, so this patch also removes the controller
function in order to disable netpoll.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_skip_exthdr() can return error code that is below zero.
'offset' is unsigned, so it makes no sense.
ipv6_skip_exthdr() returns 'int' so we can painlessly change type of
offset to int.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge protocol lives dangerously by having incestuous relations
with the IP stack. In this instance an abomination has been created
where a bogus IPCB area from a bridged packet leads to a crash in
the IP stack because it's interpreted as IP options.
This patch papers over the problem by clearing the IPCB area in that
particular spot. To fix this properly we'd also need to parse any
IP options if present but I'm way too lazy for that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
On Tue, Jul 06, 2010 at 08:48:35AM +0800, Herbert Xu wrote:
>
> bridge: Restore NULL check in br_mdb_ip_get
Resend with proper attribution.
bridge: Restore NULL check in br_mdb_ip_get
Somewhere along the line the NULL check in br_mdb_ip_get went
AWOL, causing crashes when we receive an IGMP packet with no
multicast table allocated.
This patch restores it and ensures all br_mdb_*_get functions
use it.
Reported-by: Frank Arnold <frank.arnold@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
Support more fine grained control of bridge netfilter iptables invocation
by adding seperate brnf_call_*tables parameters for each device using the
sysfs interface. Packets are passed to layer 3 netfilter when either the
global parameter or the per bridge parameter is enabled.
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Use u64_stats_sync infrastructure to provide 64bit rx/tx
counters even on 32bit hosts.
It is safe to use a single u64_stats_sync for rx and tx,
because BH is disabled on both, and we use per_cpu data.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is common in end-node, non STP bridges to set forwarding
delay to zero; which causes the forwarding database cleanup
to run every clock tick. Change to run only as soon as needed
or at next ageing timer interval which ever is sooner.
Use round_jiffies_up macro rather than attempting round up
by changing value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version of br_netpoll_send_skb used when netpoll is off is
missing a const thus causing a warning.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge multicast patches introduced an OOM crash in the forward
path, when deliver_clone fails to clone the skb.
Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register net_bridge_port pointer as rx_handler data pointer. As br_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a bridge port. Also rcuized pointers are now correctly
dereferenced in br_fdb.c and in netfilter parts.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add possibility to register rx_handler data pointer along with a rx_handler.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple problems with the newly added netpoll support:
1) Use-after-free on each netpoll packet.
2) Invoking unsafe code on netpoll/IRQ path.
3) Breaks when netpoll is enabled on the underlying device.
This patch fixes all of these problems. In particular, we now
allocate proper netpoll structures for each underlying device.
We only allow netpoll to be enabled on the bridge when all the
devices underneath it support netpoll. Once it is enabled, we
do not allow non-netpoll devices to join the bridge (until netpoll
is disabled again).
This allows us to do away with the npinfo juggling that caused
problem number 1.
Incidentally this patch fixes number 2 by bypassing unsafe code
such as multicast snooping and netfilter.
Reported-by: Qianfeng Zhang <frzhang@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netpoll always zaps npinfo we no longer need to do it
in bridge.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What this patch does is it removes two receive frame hooks (for bridge and for
macvlan) from __netif_receive_skb. These are replaced them with a single
hook for both. It only supports one hook per device because it makes no
sense to do bridging and macvlan on the same device.
Then a network driver (of virtual netdev like macvlan or bridge) can register
an rx_handler for needed net device.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid dirtying bridge_parent_rtable refcount, using new dst noref
infrastructure.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build when CONFIG_SYSFS is not enabled:
net/bridge/br_if.c:136: error: 'struct net_bridge_port' has no member named 'sysfs_name'
Note: dev->name == sysfs_name except when change name is in
progress, and we are protected from that by RTNL mutex.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Links for each port are created in sysfs using the device
name, but this could be changed after being added to the
bridge.
As well as being unable to remove interfaces after this
occurs (because userspace tools don't recognise the new
name, and the kernel won't recognise the old name), adding
another interface with the old name to the bridge will
cause an error trying to create the sysfs link.
This fixes the problem by listening for NETDEV_CHANGENAME
notifications and renaming the link.
https://bugzilla.kernel.org/show_bug.cgi?id=12743
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one set of macro's for all bridge messages.
Note: can't use netdev_XXX macro's because bridge is purely
virtual and has no device parent.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move code around so that the ifdef for NETPOLL_CONTROLLER don't have to
show up in main code path. The control functions should be in helpers
that are only compiled if needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since xt_action_param is writable, let's use it. The pointer to
'bool hotdrop' always worried (8 bytes (64-bit) to write 1 byte!).
Surprisingly results in a reduction in size:
text data bss filename
5457066 692730 357892 vmlinux.o-prev
5456554 692730 357892 vmlinux.o
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
In future, layer-3 matches will be an xt module of their own, and
need to set the fragoff and thoff fields. Adding more pointers would
needlessy increase memory requirements (esp. so for 64-bit, where
pointers are wider).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The structures carried - besides match/target - almost the same data.
It is possible to combine them, as extensions are evaluated serially,
and so, the callers end up a little smaller.
text data bss filename
-15318 740 104 net/ipv4/netfilter/ip_tables.o
+15286 740 104 net/ipv4/netfilter/ip_tables.o
-15333 540 152 net/ipv6/netfilter/ip6_tables.o
+15269 540 152 net/ipv6/netfilter/ip6_tables.o
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Based on the previous patch, make bridge support netpoll by:
1) implement the 2 methods to support netpoll for bridge;
2) modify netpoll during forwarding packets via bridge;
3) disable netpoll support of bridge when a netpoll-unabled device
is added to bridge;
4) enable netpoll support when all underlying devices support netpoll.
Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some declarations around to make it clearer which variables
are being used inside loop.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recently introduced bridge mulitcast port group list was only
partially using RCU correctly. It was missing rcu_dereference()
and missing the necessary barrier on deletion.
The code should have used one of the standard list methods (list or hlist)
instead of open coding a RCU based link list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unsafe usage of RCU. Would never work on Alpha SMP because
of lack of rcu_dereference()
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By coding slightly differently, there are only two cases
to deal with: add at head and add after previous entry.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ff65e8275f.
As explained by Stephen Hemminger, the traversal doesn't require
RCU handling as we hold a lock.
The list addition et al. calls, on the other hand, do.
Signed-off-by: David S. Miller <davem@davemloft.net>
I prefer that the hlist be only accessed through the hlist macro
objects. Explicit twiddling of links (especially with RCU) exposes
the code to future bugs.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a report from Stephen Rothwell:
--------------------
net/bridge/br_multicast.c: In function 'br_ip6_multicast_alloc_query':
net/bridge/br_multicast.c:469: error: implicit declaration of function 'csum_ipv6_magic'
Introduced by commit 08b202b672 ("bridge
br_multicast: IPv6 MLD support") from the net tree.
csum_ipv6_magic is declared in net/ip6_checksum.h ...
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with commit 32dec5dd02 ("bridge
br_multicast: Don't refer to BR_INPUT_SKB_CB(skb)->mrouters_only
without IGMP snooping."), BR_INPUT_SKB_CB(skb)->mrouters_only is
not appropriately initialized if IGMP/MLD snooping support is
compiled and disabled, so we can see garbage.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce struct br_ip{} to store ip address and protocol
and make functions more generic so that we can support
both IPv4 and IPv6 with less pain.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Sparse can help us find endianness bugs, but we need to make some
cleanups to be able to more easily spot real bugs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
grec_nsrcs is in network order, we should convert to host horder in
br_multicast_igmp3_report()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU for IP traffic encapsulated inside PPPoE traffic is smaller
than the MTU of the Ethernet device (1500). Connection tracking
gathers all IP packets and sometimes will refragment them in
ip_fragment(). We then need to subtract the length of the
encapsulating header from the mtu used in ip_fragment(). The check in
br_nf_dev_queue_xmit() which determines if ip_fragment() has to be
called is also updated for the PPPoE-encapsulated packets.
nf_bridge_copy_header() is also updated to make sure the PPPoE data
length field has the correct value.
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
- fix IP DNAT on vlan- or pppoe-encapsulated traffic: The functions
neigh_hh_output() or dst->neighbour->output() overwrite the complete
Ethernet header, although we only need the destination MAC address.
For encapsulated packets, they ended up overwriting the encapsulating
header. The new code copies the Ethernet source MAC address and
protocol number before calling dst->neighbour->output(). The Ethernet
source MAC and protocol number are copied back in place in
br_nf_pre_routing_finish_bridge_slow(). This also makes the IP DNAT
more transparent because in the old scheme the source MAC of the
bridge was copied into the source address in the Ethernet header. We
also let skb->protocol equal ETH_P_IP resp. ETH_P_IPV6 during the
execution of the PF_INET resp. PF_INET6 hooks.
- Speed up IP DNAT by calling neigh_hh_bridge() instead of
neigh_hh_output(): if dst->hh is available, we already know the MAC
address so we can just copy it.
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Remove br_netfilter.c::br_nf_local_out(). The function
br_nf_local_out() was needed because the PF_BRIDGE::LOCAL_OUT hook
could be called when IP DNAT happens on to-be-bridged traffic. The
new scheme eliminates this mess.
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
ip_refrag isn't used anymore in the bridge-netfilter code
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
bridge-netfilter: cleanup br_netfilter.c
- remove some of the graffiti at the head of br_netfilter.c
- remove __br_dnat_complain()
- remove KERN_INFO messages when CONFIG_NETFILTER_DEBUG is defined
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The IGMP3 report parsing is looking at the wrong address for
group records. This patch fixes it.
Reported-by: Banyeer <banyeer@yahoo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Restore function signatures from bool to int so that we can report
memory allocation failures or similar using -ENOMEM rather than
always having to pass -EINVAL back.
// <smpl>
@@
type bool;
identifier check, par;
@@
-bool check
+int check
(struct xt_tgchk_param *par) { ... }
// </smpl>
Minus the change it does to xt_ct_find_proto.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Restore function signatures from bool to int so that we can report
memory allocation failures or similar using -ENOMEM rather than
always having to pass -EINVAL back.
This semantic patch may not be too precise (checking for functions
that use xt_mtchk_param rather than functions referenced by
xt_match.checkentry), but reviewed, it produced the intended result.
// <smpl>
@@
type bool;
identifier check, par;
@@
-bool check
+int check
(struct xt_mtchk_param *par) { ... }
// </smpl>
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The first argument to NF_HOOK* is an nfproto since quite some time.
Commit v2.6.27-2457-gfdc9314 was the first to practically start using
the new names. Do that now for the remaining NF_HOOK calls.
The semantic patch used was:
// <smpl>
@@
@@
(NF_HOOK
|NF_HOOK_THRESH
)(
-PF_BRIDGE,
+NFPROTO_BRIDGE,
...)
@@
@@
NF_HOOK(
-PF_INET6,
+NFPROTO_IPV6,
...)
@@
@@
NF_HOOK(
-PF_INET,
+NFPROTO_IPV4,
...)
// </smpl>
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Supplement to 1159683ef4.
Downgrade the log level to INFO for most checkentry messages as they
are, IMO, just an extra information to the -EINVAL code that is
returned as part of a parameter "constraint violation". Leave errors
to real errors, such as being unable to create a LED trigger.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
We never actually use iph again so this assignment can be removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not desired for underlaying devices to change type. At the time,
there is for example possible to have bond with changed type from
Ethernet to Infiniband as a port of a bridge. This patch fixes this.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENOMEM is a very obvious error code (cf. EINVAL), so I think we do not
really need a warning message. Not to mention that if the allocation
fails, the user is most likely going to get a stack trace from slab
already.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The shared packet statistics are a potential source of slow down
on bridged traffic. Convert to per-cpu array, but only keep those
statistics which change per-packet.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_BRIDGE_IGMP_SNOOPING,
BR_INPUT_SKB_CB(skb)->mrouters_only is not appropriately
initialized, so we can see garbage.
A clear option to fix this is to set it even without that
config, but we cannot optimize out the branch.
Let's introduce a macro that returns value of mrouters_only
and let it return 0 without CONFIG_BRIDGE_IGMP_SNOOPING.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Michael Braun <michael-dev@fami-braun.de>
bridge: Fix br_forward crash in promiscuous mode
It's a linux-next kernel from 2010-03-12 on an x86 system and it
OOPs in the bridge module in br_pass_frame_up (called by
br_handle_frame_finish) because brdev cannot be dereferenced (its set to
a non-null value).
Adding some BUG_ON statements revealed that
BR_INPUT_SKB_CB(skb)->brdev == br-dev
(as set in br_handle_frame_finish first)
only holds until br_forward is called.
The next call to br_pass_frame_up then fails.
Digging deeper it seems that br_forward either frees the skb or passes
it to NF_HOOK which will in turn take care of freeing the skb. The
same is holds for br_pass_frame_ip. So it seems as if two independent
skb allocations are required. As far as I can see, commit
b33084be19 ("bridge: Avoid unnecessary
clone on forward path") removed skb duplication and so likely causes
this crash. This crash does not happen on 2.6.33.
I've therefore modified br_forward the same way br_flood has been
modified so that the skb is not freed if skb0 is going to be used
and I can confirm that the attached patch resolves the issue for me.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all callers of br_mdb_ip_get need to check whether the
hash table is NULL, this patch moves the check into the function.
This fixes the two callers (query/leave handler) that didn't
check it.
Reported-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Paul McKenny for pointing out that it is incorrect to use
synchronize_rcu_bh to ensure that pending callbacks have completed.
Instead we should use rcu_barrier_bh.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Paul McKenney correctly pointed out, __br_mdb_ip_get needs
to use the RCU list walking primitive in order to work correctly
on platforms where data-dependency ordering is not guaranteed.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereference "port" on the lines immediately before and immediately
after the test so port should hopefully never be null here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast calls ip_send_check(), so it should depend on INET.
built-in:
br_multicast.c:(.text+0x88cf4): undefined reference to `ip_send_check'
or modular:
ERROR: "ip_send_check" [net/bridge/bridge.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build error when IGMP_SNOOPING is not enabled.
In file included from net/bridge/br.c:24:
net/bridge/br_private.h: In function 'br_multicast_is_router':
net/bridge/br_private.h:361: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:362: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:363: error: 'struct net_bridge' has no member named 'multicast_router_timer'
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to the IGMP parameters related to the
snooping function of the bridge. This includes various time
values and retransmission limits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to control the hash elasticity/max
parameters. The elasticity setting does not take effect until
the next new multicast group is added. At which point it is
checked and if after rehashing it still can't be satisfied then
snooping will be disabled.
The max setting on the other hand takes effect immediately. It
must be a power of two and cannot be set to a value less than the
current number of multicast group entries. This is the only way
to shrink the multicast hash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to disable IGMP snooping completely
through a sysfs toggle. It also allows the user to reenable
snooping when it has been automatically disabled due to hash
collisions. If the collisions have not been resolved however
the system will refuse to reenable snooping.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to forcibly enable/disable ports as
having multicast routers attached. A port with a multicast router
will receive all multicast traffic.
The value 0 disables it completely. The default is 1 which lets
the system automatically detect the presence of routers (currently
this is limited to picking up queries), and 2 means that the port
will always receive all multicast traffic.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finally hooks up the multicast snooping module to the
data path. In particular, all multicast packets passing through
the bridge are fed into the module and switched by it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch hooks up the bridge start/stop and add/delete/disable
port functions to the new multicast module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to perform selective multicast forwarding.
We forward multicast traffic to a set of ports plus all multicast
router ports. In order to avoid duplications among these two
sets of ports, we order all ports by the numeric value of their
pointers. The two lists are then walked in lock-step to eliminate
duplicates.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the core functionality of IGMP snooping support
without actually hooking it up. So this patch should be a no-op
as far as the bridge's external behaviour is concerned.
All the new code and data is controlled by the Kconfig option
BRIDGE_IGMP_SNOOPING. A run-time toggle is also available.
The multicast switching is done using an hash table that is
lockless on the read-side through RCU. On the write-side the
new multicast_lock is used for all operations. The hash table
supports dynamic growth/rehashing.
The hash table will be rehashed if any chain length exceeds a
preset limit. If rehashing does not reduce the maximum chain
length then snooping will be disabled.
These features may be added in future (in no particular order):
* IGMPv3 source support
* Non-querier router detection
* IPv6
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the main loop body in br_flood into the function
may_deliver. The code that clones an skb and delivers it is moved
into the deliver_clone function.
This allows this to be reused by the future multicast forward
function.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch makes BR_INPUT_SKB_CB available on the xmit path so
that we could avoid passing the br pointer around for the purpose
of collecting device statistics.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the packet is delivered to the local bridge device we may
end up cloning it unnecessarily if no bridge port can receive
the packet in br_flood.
This patch avoids this by moving the skb_clone into br_flood.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows tail-call on the call to br_pass_frame_up
in br_handle_frame_finish. This is now possible because of the
previous patch to call br_pass_frame_up last.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment we deliver to the local bridge port via the function
br_pass_frame_up before all other ports. There is no requirement
for this.
For the purpose of IGMP snooping, it would be more convenient if
we did the local port last. Therefore this patch rearranges the
bridge input processing so that the local bridge port gets to see
the packet last (if at all).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the required handlers to convert 32 bit
ebtables mark match and match target structs to 64bit layout.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
ebt_limit structure is larger on 64 bit systems due
to "long" type used in the (kernel-only) data section.
Setting .compatsize is enough in this case, these values
have no meaning in userspace.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
ebtables can be compiled to perform userspace-side padding of
structures. In that case, all the structures are already in the
'native' format expected by the kernel.
This tries to determine what format the userspace program is
using.
For most set/getsockopts, this can be done by checking
the len argument for sizeof(compat_ebt_replace) and
re-trying the native handler on error.
In case of EBT_SO_GET_ENTRIES, the native handler is tried first,
it will error out early when checking the *len argument
(the compat version has to defer this check until after
iterating over the kernel data set once, to adjust for all
the structure size differences).
As this would cause error printks, remove those as well, as
recommended by Bart de Schuymer.
Signed-off-by: Florian Westphal <fw@strlen.de>
Main code for 32 bit userland ebtables binary with 64 bit kernels
support.
Tested on x86_64 kernel only, using 64bit ebtables binary
for output comparision.
At least ebt_mark, m_mark and ebt_limit need CONFIG_COMPAT hooks, too.
remaining problem:
The ebtables userland makefile has:
ifeq ($(shell uname -m),sparc64)
CFLAGS+=-DEBT_MIN_ALIGN=8 -DKERNEL_64_USERSPACE_32
endif
struct ebt_replace, ebt_entry_match etc. then contain userland-side
padding, i.e. even if we are called from a 32 bit userland, the
structures may already be in the right format.
This problem is addressed in a follow-up patch.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
allows to call do_update_counters() from upcoming CONFIG_COMPAT
code instead of copy&pasting the same code.
Signed-off-by: Florian Westphal <fw@strlen.de>
once CONFIG_COMPAT support is added to ebtables, the new
copy_counters_to_user function can be called instead of duplicating
code.
Also remove last use of MEMPRINT, as requested by Bart De Schuymer.
Signed-off-by: Florian Westphal <fw@strlen.de>
once CONFIG_COMPAT support is merged this allows
to call do_replace_finish() after doing the CONFIG_COMPAT conversion
instead of copy & pasting this.
Signed-off-by: Florian Westphal <fw@strlen.de>
This will cause trouble once CONFIG_COMPAT support is added to ebtables.
xt_compat_*_offset() calculate the kernel/userland structure size delta
using:
XT_ALIGN(size) - COMPAT_XT_ALIGN(size)
If the match/target sizes are aligned at registration time,
delta is always zero.
Should have zero effect for existing systems: xtables uses
XT_ALIGN() whenever it deals with match/target sizes.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
next_offset must be > 0, otherwise this loops forever.
The offset also contains the size of the ebt_entry structure
itself, so anything smaller is invalid.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch removes the unused age_list member from the net_bridge
structure.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ->net to match destructor list like ->net in constructor list.
Make sure it's set in ebtables/iptables/ip6tables, this requires to
propagate netns up to *_unregister_table().
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Some complex match modules (like xt_hashlimit/xt_recent) want netns
information at constructor and destructor time. We propably can play
games at match destruction time, because netns can be passed in object,
but I think it's cleaner to explicitly pass netns.
Add ->net, make sure it's set from ebtables/iptables/ip6tables code.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
__net_init/__net_exit are apparently not going away, so use them
to full extent.
In some cases __net_init was removed, because it was called from
__net_exit code.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
normal users are currently allowed to set/modify ebtables rules.
Restrict it to processes with CAP_NET_ADMIN.
Note that this cannot be reproduced with unmodified ebtables binary
because it uses SOCK_RAW.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
* transmitter, which must be equal to the sender (origin)
* receiver (on the wireless medium), which is the AP in
the case of managed mode
* the recipient (destination), which is on the APs local
network segment
In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.
To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.
Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resolve the conflict between v2.6.32-rc7 where dn_def_dev_handler
gets a small bug fix and the sysctl tree where I am removing all
sysctl strategy routines.
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
add_del_if() is called with RTNL, we can use __dev_get_by_index()
instead of [dev_get_by_index() + dev_put()]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge code assumes ethernet addressing, so be more strict in
the what is allowed. This showed up when GRE had a bug and was not
using correct address format.
Add some more comments for increased clarity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speedup module unloading by factorizing synchronize_rcu() calls
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow enable/disable UFO on bridge device via ethtool
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential double-kfree in net/bridge/br_if.c. If br_fdb_insert
fails, then the kobject is put back (which calls kfree due to the kobject
release), and then kfree is called again on the net_bridge_port. This
patch fixes the crash.
Thanks to Stephen Hemminger for the one-line fix.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 19eda87 (netfilter: change return types of check functions for
Ebtables extensions) broke the ebtables ulog module by missing a return
value conversion.
Signed-off-by: Patrick McHardy <kaber@trash.net>
commit f216f082b2
([NETFILTER]: bridge netfilter: deal with martians correctly)
added a refcount leak on in_dev.
Instead of using in_dev_get(), we can use __in_dev_get_rcu(),
as netfilter hooks are running under rcu_read_lock(), as pointed
by Patrick.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The inputted table is never modified, so should be considered const.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds a 'hairpin' (also called 'reflective relay') mode
port configuration to the Linux Ethernet bridge kernel module.
A bridge supporting hairpin forwarding mode can send frames back
out through the port the frame was received on.
Hairpin mode is required to support basic VEPA (Virtual
Ethernet Port Aggregator) capabilities.
You can find additional information on VEPA here:
http://tech.groups.yahoo.com/group/evb/http://www.ieee802.org/1/files/public/docs2009/new-hudson-vepa_seminar-20090514d.pdfhttp://www.internet2.edu/presentations/jt2009jul/20090719-congdon.pdf
An additional patch 'bridge-utils: Add 'hairpin' port forwarding mode'
is provided to allow configuring hairpin mode from userspace tools.
Signed-off-by: Paul Congdon <paul.congdon@hp.com>
Signed-off-by: Anna Fischer <anna.fischer@hp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ebt_log uses its own implementation of print_mac to print MAC addresses.
This patch converts it to use the %pM conversion specifier for printk.
Signed-off-by: Tobias Klauser <klto@zhaw.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
String literals are constant, and usually, we can also tag the array
of pointers const too, moving it to the .rodata section.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
kobject_init_and_add will alloc memory for kobj->name, so in br_add_if
error path, simply use kobject_del will not free memory for kobj->name.
Fix by using kobject_put instead, kobject_put will internally calls
kobject_del and frees memory for kobj->name.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No functional change -- just for easier reading.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unloading modules that uses call_rcu() callbacks, then we must
use rcu_barrier(). This module uses syncronize_net() which is not
enough to be sure that all callback has been completed.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes FDB entry check for ATM LANE bridge integration.
There's no point in holding a FDB entry around SKB building.
br_fdb_get()/br_fdb_put() pair are changed into single br_fdb_test_addr()
hook that checks if the addr has FDB entry pointing to other port
to the one the request arrived on.
FDB entry refcounting is removed as it's not used anywhere else.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holding rtnl_lock when we are unregistering the sysfs files can
deadlock if we unconditionally take rtnl_lock in a sysfs file. So fix
it with the now familiar patter of: rtnl_trylock and syscall_restart()
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bridge is configured with no STP and forwarding delay of 0 (which
is typical for virtualization) then when link starts it will flood all
packets for the first 20 seconds.
This bug was introduced by a combination of earlier changes:
* forwarding database uses hold time of zero to indicate
user wants to always flood packets
* optimzation of the case of forwarding delay of 0 avoids the initial
timer tick
The fix is to just skip all the topology change detection code if
kernel STP is not being used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge catches all STP packets; even if STP is turned
off. This prevents other systems (which do have STP turned on)
from being able to detect loops in the network.
With this patch, if STP is off, then any packet sent to the STP
multicast group address is forwarded to all ports.
Based on earlier patch by Joakim Tjernlund with changes
to go through forwarding (not local chain), and optimization
that only last octet needs to be checked.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_nf_dev_queue_xmit only checks for ETH_P_IP packets for fragmenting but not
VLAN packets. This results in dropping of large VLAN packets. This can be
observed when connection tracking is enabled. Connection tracking re-assembles
fragmented packets, and these have to re-fragmented when transmitting out. Also,
make sure only refragmented packets are defragmented as per suggestion from
Patrick McHardy.
Signed-off-by: Saikiran Madugula <hummerbliss@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch renames the ebt_ulog nf_logger from "ulog" to "ebt_ulog" to
be in sync with other modules naming. As this name was currently only
used for informational purpose, the renaming should be harmless.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ebt_ulog module does not follow the fixed convention about function
return. Loading the module is triggering the following message:
sys_init_module: 'ebt_ulog'->init suspiciously returned 1, it should follow 0/-E convention
sys_init_module: loading module anyway...
Pid: 2334, comm: modprobe Not tainted 2.6.29-rc5edenwall0-00883-g199e57b #146
Call Trace:
[<c0441b81>] ? printk+0xf/0x16
[<c02311af>] sys_init_module+0x107/0x186
[<c0202cfa>] syscall_call+0x7/0xb
The following patch fixes the return treatment in ebt_ulog_init()
function.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the declaration of the logger structure in ebt_log
and ebt_ulog: I forgot to remove the const option from their declaration
in the commit ca735b3aaa ("netfilter:
use a linked list of loggers").
Pointed-out-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an crash when empty bond device is added to a bridge.
If an interface with invalid ethernet address (all zero) is added
to a bridge, then bridge code detects it when setting up the forward
databas entry. But the error unwind is broken, the bridge port object
can get freed twice: once when ref count went to zeo, and once by kfree.
Since object is never really accessible, just free it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initialization of the lock element is not needed
since the lock is always initialized in ebt_register_table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8cc784ee (netfilter: change return types of match functions
for ebtables extensions) broke ebtables matches by inverting the
sense of match/nomatch.
Reported-by: Matt Cross <matthltc@us.ibm.com>
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPPOE/VLAN processing code in the bridge netfilter is broken
by design. The VLAN tag and the PPPOE session ID are an integral
part of the packet flow information, yet they're completely
ignored by the bridge netfilter. This is potentially a security
hole as it treats all VLANs and PPPOE sessions as the same.
What's more, it's actually broken for PPPOE as the bridge netfilter
tries to trim the packets to the IP length without adjusting the
PPPOE header (and adjusting the PPPOE header isn't much better
since the PPPOE peer may require the padding to be present).
Therefore we should disable this by default.
It does mean that people relying on this feature may lose networking
depending on how their bridge netfilter rules are configured.
However, IMHO the problems this code causes are serious enough to
warrant this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge FORWARD/POST_ROUTING chains treats all
non-IPv4 packets as IPv6. This packet fixes that by returning
NF_ACCEPT on non-IP packets instead, just as is done in PRE_ROUTING.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As GRE tries to call the update_pmtu function on skb->dst and
bridge supplies an skb->dst that has a NULL ops field, all is
not well.
This patch fixes this by giving the bridge device an ops field
with an update_pmtu function. For the moment I've left all
other fields blank but we can fill them in later should the
need arise.
Based on report and patch by Philip Craig.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to net_device_ops function table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ebt_unregister_table() can be called during netns stop, and module
pinning scheme can't prevent netns stop, do table cleanup by hand.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* return ebt_table from ebt_register_table(), module code will save it into
per-netns data for unregistration
* duplicate ebt_table at the very beginning of registration -- it's added into
list, so one ebt_table wouldn't end up in many lists (and each netns has
different one)
* introduce underscored tables in individial modules, this is temporary to not
break bisection.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* propagate netns from userspace, register table in passed netns
* remporarily register every ebt_table in init_net
P. S.: one needs to add ".netns_ok = 1" to igmp_protocol to test with
ebtables(8) in netns.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open code NIP6_FMT in the one call inside sscanf and one user
of NIP6() that could use %p6 in the netfilter code.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My change
commit e2a6b85247
net: Enable TSO if supported by at least one device
didn't do what was intended because the netdev_compute_features
function was designed for conjunctions. So what happened was that
it would simply take the TSO status of the last constituent device.
This patch extends it to support both conjunctions and disjunctions
under the new name of netdev_increment_features.
It also adds a new function netdev_fix_features which does the
sanity checking that usually occurs upon registration. This ensures
that the computation doesn't result in an illegal combination
since this checking is absent when the change is initiated via
ethtool.
The two users of netdev_compute_features have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Supplements: ee999d8b95)
NFPROTO_ARP actually has a different value from NF_ARP, so ensure all
callers use the new value so that packets _do_ get delivered to the
registered hooks.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller