This patch implements support for sampling of a touchscreen into
the MXS LRADC driver. The LRADC block allows configuring some of
it's channels into special mode where they either output the drive
voltage or sample it, allowing it to operate a 4-wire or 5-wire
resistive touchscreen.
In case the touchscreen mode is enabled, the LRADC slot #7 is
reserved for touchscreen only, therefore it is not possible to
sample 8 LRADC channels at time, but only 7 channels.
The touchscreen controller is configured such that the PENDOWN event
disables touchscreen interrupts and triggers execution of worker
thread, which then polls the touchscreen controller for X, Y and
Pressure values. This reduces the overhead of interrupt-driven
operation. Upon the PENUP event, the worker thread re-enables the
PENDOWN detection interrupt and exits.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The relation between PIN_BANK numbers and pio letters wasn't made very
clear.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7Dk+AAoJEFBXWFqHsHzOUugIAJZblDy7ORFZhW0R8L4Be541
pS5aBGFY7VYCrL9BGUKGsLuITI+arbYFHc+H4nqhNMBAvgChPxJZMnaG4kp1Q5Vm
AVr9tNrwsauVHLlryUk4ekut4G4WWo1NDcFq4S6rxD/jxA/uP6rnMUCY6PX4LLL9
ZpGDb3BWQ2bbUaANu3cjc1I1/Gle1ir9LObm6ZC6l8MHTTG7hyTMHvS8eCZzmDbc
9z01ZrvTKn1AneeHOpArd2/jo14b6Kap8ykx2hdVUeBhIbZp3pomezZau9ya8/kB
+1BQVODdkOMzBm6gkIkfU3HbUPnIPL18MG/uKyD+f67YkX5YODinUVdq63upLxc=
=7yrS
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mx5: Fix MX53 flexcan2 clock
ARM: dts: imx31-bug: Fix manufacturer compatible string
clk: imx: Remove 'clock-output-names' from the examples
Improve the documentation to clarify level vs edge triggered power off.
Improve the comments for level vs edge triggered power off.
Make use of gpio_is_valid().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
'clock-output-names' is not used in any of the dts/dtsi files for i.mx.
Remove it from the examples, so that the example and the real usage in the
dtsi files can match.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory
corruption in the at91 driver
- Add the missing device tree binding doc for the
SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration
from the device tree, it was previously retired
from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin
controller.
- Provide the prcm_base from the device tree in the
DT boot path for the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ca6M
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"A first round of pinctrl fixes for v3.8:
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory corruption in the at91
driver
- Add the missing device tree binding doc for the SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration from the device
tree, it was previously retired from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin controller.
- Provide the prcm_base from the device tree in the DT boot path for
the Nomadik pin controller."
* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
ARM: ux500: add pinctrl address resources
pinctrl: nomadik: return if prcm_base is NULL
pinctrl: sirf: enable GPIO pullup/down configuration from dts
pinctrl: sirf: add missing DT-binding document
pinctrl: fix comment mistake
drivers/pinctrl/pinctrl-at91.c: convert kfree to devm_kfree
pinctrl: imx5: fix GPIO_8 pad CAN1_RXCAN configuration
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
commit 7bec207427 remove sirfsoc_gpio_set_pull function,
this patches takes the feature back by adding sirf,pullups and
sirf,pulldowns prop in dts, and the driver will set the GPIO
pull according to the dts.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While sending email to Linus for reviewing:
"pinctrl: sirf: add DT-binding pinmux mapping support"
https://patchwork.kernel.org/patch/1364361/
i have included the devicetree/bindings/pinctrl/pinctrl-sirf.txt
But while sending pull request with commit 056876f6c7,
i missed the document.
this patch takes the document back.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull watchdog updates from Wim Van Sebroeck:
"This includes some fixes and code improvements (like
clk_prepare_enable and clk_disable_unprepare), conversion from the
omap_wdt and twl4030_wdt drivers to the watchdog framework, addition
of the SB8x0 chipset support and the DA9055 Watchdog driver and some
OF support for the davinci_wdt driver."
* git://www.linux-watchdog.org/linux-watchdog: (22 commits)
watchdog: mei: avoid oops in watchdog unregister code path
watchdog: Orion: Fix possible null-deference in orion_wdt_probe
watchdog: sp5100_tco: Add SB8x0 chipset support
watchdog: davinci_wdt: add OF support
watchdog: da9052: Fix invalid free of devm_ allocated data
watchdog: twl4030_wdt: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
watchdog: remove depends on CONFIG_EXPERIMENTAL
watchdog: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
watchdog: DA9055 Watchdog driver
watchdog: omap_wdt: eliminate goto
watchdog: omap_wdt: delete redundant platform_set_drvdata() calls
watchdog: omap_wdt: convert to devm_ functions
watchdog: omap_wdt: convert to new watchdog core
watchdog: WatchDog Timer Driver Core: fix comment
watchdog: s3c2410_wdt: use clk_prepare_enable and clk_disable_unprepare
watchdog: imx2_wdt: Select the driver via ARCH_MXC
watchdog: cpu5wdt.c: add missing del_timer call
watchdog: hpwdt.c: Increase version string
watchdog: Convert twl4030_wdt to watchdog core
davinci_wdt: preparation for switch to common clock framework
...
error and a missing symbol export.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=srgY
-----END PGP SIGNATURE-----
mergetag object bc1008cf7d
type commit
tag gpio-for-linus
tagger Grant Likely <grant.likely@secretlab.ca> 1355962627 +0000
GPIO device driver bug fixes:
- gpio/mvebu-gpio: Make mvebu-gpio depend on OF_CONFIG
- gpio/ich: Add missing spinlock init
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JGvn
-----END PGP SIGNATURE-----
mergetag object d3601e56cf
type commit
tag spi-for-linus
tagger Grant Likely <grant.likely@secretlab.ca> 1355962904 +0000
SPI device driver bug fixes branch for the v3.8 merge window. Most of
this is bug fixes to the core code and the sh-hspi and s3c64xx device
drivers.
There is also a patch here to add DT support to the Atmel driver. This
one should have been in the first round, but I missed it. It's a low
risk change contained within a single driver and the Atmel maintainer
has requested it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQ0lxNAAoJEEFnBt12D9kBCTMP/0WvS/7iiilM00b5pmclGkRc
Ct3832KnZXn5dDYoSsP1AS2PRJAKbrMzvKMZu+ggjOAlwza87rKJJpt+KdU3r15b
+KElnaStCC88ohxEOwQV4+CJpF3dS1AmrGMQvo9RK8hddpR1dH+FgMdmex104X/A
Ysr0WgqQMY3iGVmnlPxU4EYlR1scnqOpaNADNbMY7ibuJ7LOYk1RYtqmX5yxdnJq
yABILFa10qV9N/cqPBu2Cuhw8Xtp/u70dsQPkALG//pyZnFyhw6rMJ6bowOC2IHM
p3R4IrVqJq1a3nL1IC1XX5/k21b0PBNxfOGqpeU4QoDK4/cIKeiPny1dtoI1UM+2
mpTU99VvitZ0ywolenKnbPdU61UwZ6Sd+ptsZM0Y/wIMiXDWSBDTZqVJRAbINqFb
JwwjtdaFDPgtIb6Yg1WuhLmhcOPfXFIRys7JmnS0VNQCpvvEIdFsR9l5jjMcmluR
W7V69z9FZj5lf7WjNstbAxbCvrw1i65OD6Nr1UBAA17bqNU6a9BCWdNJGwLozraR
k2ZomvfmIMhTP82z5by5UY39M9B5uGOHDxxXZOOvxzB/fxlYgLhiAGPfMY1FMrPH
48gDqQtdOpakL1B/gVELpBLMoKjwEx9jJa/8tJb5wy8EgNSw06BDSN69OclLgmV/
uVnSZWrp62odDLz0qjSR
=trRO
-----END PGP SIGNATURE-----
Merge tags 'dt-for-linus', 'gpio-for-linus' and 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull devicetree, gpio and spi bugfixes from Grant Likely:
"Device tree v3.8 bug fix:
- Fixes an undefined struct device build error and a missing symbol
export.
GPIO device driver bug fixes:
- gpio/mvebu-gpio: Make mvebu-gpio depend on OF_CONFIG
- gpio/ich: Add missing spinlock init
SPI device driver bug fixes:
- Most of this is bug fixes to the core code and the sh-hspi and
s3c64xx device drivers.
- There is also a patch here to add DT support to the Atmel driver.
This one should have been in the first round, but I missed it.
It's a low risk change contained within a single driver and the
Atmel maintainer has requested it."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of: define struct device in of_platform.h if !OF_DEVICE and !OF_ADDRESS
of: Fix export of of_find_matching_node_and_match()
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/mvebu-gpio: Make mvebu-gpio depend on OF_CONFIG
gpio/ich: Add missing spinlock init
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/sh-hspi: fix return value check in hspi_probe().
spi: fix tegra SPI binding examples
spi/atmel: add DT support
of/spi: Fix SPI module loading by using proper "spi:" modalias prefixes.
spi: Change FIFO flush operation and spi channel off
spi: Keep chipselect assertion during one message
This adds OF support for davinci_wdt driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlDSAa4ACgkQdwG7hYl686MMcACeNYa//ghPtccb5L+IRXsqaFDL
Yi4AoLWOaOjN8qM4KUF/bfMEkwNGAePz
=DaAQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
A new driver has been added for the SPEAr platform and the TWL4030/6030
driver has been replaced by two drivers that control the regular PWMs
and the PWM driven LEDs provided by the chips.
The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have all
been improved and the device tree bindings now support the PWM signal
polarity.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=m+7I
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"A new driver has been added for the SPEAr platform and the
TWL4030/6030 driver has been replaced by two drivers that control the
regular PWMs and the PWM driven LEDs provided by the chips.
The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have
all been improved and the device tree bindings now support the PWM
signal polarity."
Fix up trivial conflicts due to __devinit/exit removal.
* tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (21 commits)
pwm: samsung: add missing s3c->pwm_id assignment
pwm: lpc32xx: Set the chip base for dynamic allocation
pwm: lpc32xx: Properly disable the clock on device removal
pwm: lpc32xx: Fix the PWM polarity
pwm: i.MX: eliminate build warning
pwm: Export of_pwm_xlate_with_flags()
pwm: Remove pwm-twl6030 driver
pwm: New driver to support PWM driven LEDs on TWL4030/6030 series of PMICs
pwm: New driver to support PWMs on TWL4030/6030 series of PMICs
pwm: pwm-tiehrpwm: pinctrl support
pwm: tiehrpwm: Add device-tree binding
pwm: pwm-tiehrpwm: Adding TBCLK gating support.
pwm: pwm-tiecap: pinctrl support
pwm: tiecap: Add device-tree binding
pwm: Add TI PWM subsystem driver
pwm: Device tree support for PWM polarity
pwm: vt8500: Ensure PWM clock is enabled during pwm_config
pwm: vt8500: Fix build error
pwm: spear: Staticize spear_pwm_config()
pwm: Add SPEAr PWM chip driver support
...
Fix name of slink binding and address of sflash example to make it
self consistent.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
Pull second round of input updates from Dmitry Torokhov:
"As usual, there are a couple of new drivers, input core now supports
managed input devices (devres), a slew of drivers now have device tree
support and a bunch of fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
Input: walkera0701 - fix crash on startup
Input: matrix-keymap - provide a proper module license
Input: gpio_keys_polled - switch to using gpio_request_one()
Input: gpio_keys - switch to using gpio_request_one()
Input: wacom - fix touch support for Bamboo Fun CTH-461
Input: xpad - add a few new VID/PID combinations
Input: xpad - minor formatting fixes
Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
Input: tca8418-keypad - switch to using managed resources
Input: tca8418_keypad - increase severity of failures in probe()
Input: tca8418_keypad - move device ID tables closer to where they are used
Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
Input: tca8418_keypad - use a temporary variable for parent device
Input: tca8418_keypad - add support for shared interrupt
Input: tca8418_keypad - add support for device tree bindings
Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
Input: bu21013_ts - add support for Device Tree booting
Input: bu21013_ts - move GPIO init and exit functions into the driver
Input: bu21013_ts - request regulator that actually exists
ARM: ux500: Strip out duplicate touch screen platform information
...
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlight is probably some base POWER8 support. There's more
to come such as transactional memory support but that will wait for
the next one.
Overall it's pretty quiet, or rather I've been pretty poor at picking
things up from patchwork and reviewing them this time around and Kumar
no better on the FSL side it seems..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (73 commits)
powerpc+of: Rename and fix OF reconfig notifier error inject module
powerpc: mpc5200: Add a3m071 board support
powerpc/512x: don't compile any platform DIU code if the DIU is not enabled
powerpc/mpc52xx: use module_platform_driver macro
powerpc+of: Export of_reconfig_notifier_[register,unregister]
powerpc/dma/raidengine: add raidengine device
powerpc/iommu/fsl: Add PAMU bypass enable register to ccsr_guts struct
powerpc/mpc85xx: Change spin table to cached memory
powerpc/fsl-pci: Add PCI controller ATMU PM support
powerpc/86xx: fsl_pcibios_fixup_bus requires CONFIG_PCI
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
powerpc/85xx: p1022ds: Use NULL instead of 0 for pointers
powerpc: Disable relocation on exceptions when kexecing
powerpc: Enable relocation on during exceptions at boot
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
powerpc: Add wrappers to enable/disable relocation on exceptions
powerpc: Add set_mode hcall
powerpc: Setup relocation on exceptions for bare metal systems
powerpc: Move initial mfspr LPCR out of __init_LPCR
powerpc: Add relocation on exception vector handlers
...
Add device tree support to the rtc-imxdi driver.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enhance rtc-omap driver with DT capability
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the newly introduce cs-gpios dt support on atmel.
We do not use the hardware cs as it's wired and has bugs and limitations.
As the controller believes that only active-low devices/systems exists.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull DRM updates from Dave Airlie:
"This is the one and only next pull for 3.8, we had a regression we
found last week, so I was waiting for that to resolve itself, and I
ended up with some Intel fixes on top as well.
Highlights:
- new driver: nvidia tegra 20/30/hdmi support
- radeon: add support for previously unused DMA engines, more HDMI
regs, eviction speeds ups and fixes
- i915: HSW support enable, agp removal on GEN6, seqno wrapping
- exynos: IPP subsystem support (image post proc), HDMI
- nouveau: display class reworking, nv20->40 z compression
- ttm: start of locking fixes, rcu usage for lookups,
- core: documentation updates, docbook integration, monotonic clock
usage, move from connector to object properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (590 commits)
drm/exynos: add gsc ipp driver
drm/exynos: add rotator ipp driver
drm/exynos: add fimc ipp driver
drm/exynos: add iommu support for ipp
drm/exynos: add ipp subsystem
drm/exynos: support device tree for fimd
radeon: fix regression with eviction since evict caching changes
drm/radeon: add more pedantic checks in the CP DMA checker
drm/radeon: bump version for CS ioctl support for async DMA
drm/radeon: enable the async DMA rings in the CS ioctl
drm/radeon: add VM CS parser support for async DMA on cayman/TN/SI
drm/radeon/kms: add evergreen/cayman CS parser for async DMA (v2)
drm/radeon/kms: add 6xx/7xx CS parser for async DMA (v2)
drm/radeon: fix htile buffer size computation for command stream checker
drm/radeon: fix fence locking in the pageflip callback
drm/radeon: make indirect register access concurrency-safe
drm/radeon: add W|RREG32_IDX for MM_INDEX|DATA based mmio accesss
drm/exynos: support extended screen coordinate of fimd
drm/exynos: fix x, y coordinates for right bottom pixel
drm/exynos: fix fb offset calculation for plane
...
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming common
display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KVPX
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev changes from Tomi Valkeinen:
"OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming
common display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller"
* tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (191 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
drivers/video/console/softcursor.c: remove redundant NULL check before kfree()
drivers/video: add support for the Solomon SSD1307 OLED Controller
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
...
Conflicts:
arch/arm/mach-davinci/devices-da8xx.c
arch/arm/plat-omap/common.c
drivers/media/platform/omap/omap_vout.c
This is a branch with updates for Marvell's mvebu/kirkwood platforms. They
came in late-ish, and were heavily interdependent such that it didn't
make sense to split them up across the cross-platform topic branches. So
here they are (for the second release in a row) in a branch on their own.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7luC
-----END PGP SIGNATURE-----
Merge tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
This branch contains device-tree updates for the SPEAr platform.
They had dependencies on earlier branches from this merge window,
which is why they were broken out in a separate branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=iK4W
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree updates, take 2, from Olof Johansson:
"This branch contains device-tree updates for the SPEAr platform. They
had dependencies on earlier branches from this merge window, which is
why they were broken out in a separate branch."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/
ARM: SPEAr320: DT: Add SPEAr 320 HMI board support
ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor
ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT
ARM: SPEAr1310: Fix AUXDATA for compact flash controller
ARM: SPEAr13xx: Remove fields not required for ssp controller
ARM: SPEAr1310: Move 1310 specific misc register into machine specific files
ARM: SPEAr: DT: Update device nodes
ARM: SPEAr: DT: add uart state to fix warning
ARM: SPEAr: DT: Modify DT bindings for STMMAC
ARM: SPEAr: DT: Fix existing DT support
ARM: SPEAr: DT: Update partition info for MTD devices
ARM: SPEAr: DT: Update pinctrl list
ARM: SPEAr13xx: DT: Add spics gpio controller nodes
This is the second batch of SoC updates for the 3.8 merge window,
containing parts that had dependencies on earlier branches such that we
couldn't include them with the first branch.
These are general updates for Samsung Exynos, Renesas/shmobile and a
topic branch that adds SMP support to Altera's socfpga platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=77Ct
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Soc updates, take 2, from Olof Johansson:
"This is the second batch of SoC updates for the 3.8 merge window,
containing parts that had dependencies on earlier branches such that
we couldn't include them with the first branch.
These are general updates for Samsung Exynos, Renesas/shmobile and a
topic branch that adds SMP support to Altera's socfpga platform."
Fix up conflicts mostly as per Olof.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
sh: clkfwk: fixup unsed variable warning
Revert "ARM: shmobile: r8a7779: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: sh73a0: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: emev2: Replace modify_scu_cpu_psr with scu_power_mode"
ARM: highbank: use common debug_ll_io_init
ARM: shmobile: sh7372: sh7372_fsiXck_clk become non-global
ARM: shmobile: sh7372: remove fsidivx clock
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
Merging in the smp-on-socfpga branch into soc2 since the topics are similar
and it's a short branch in the first place.
* next/smp:
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
Signed-off-by: Olof Johansson <olof@lixom.net>
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace the
proprietary Nokia BME stack;
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks to
Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers;
- Random fixups and enhancements for a bunch of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQyFGdAAoJEGgI9fZJve1bYy8P/iu4XRL2kNwmPD7fMO+bZSao
xCSi8zRCnOtDutB48MQXIDTi1+I64+Qqq5xTuHW5n/T0zJ88biGBZfmJLjM88oQ4
ZqfO/axT6/MNFXTQtxEvXtn/AoM6lp9ZLmIbs7mkSpcnuG8iY5eovKfeyyNiAoGh
W6ISc9d1zZl8JYZXkkX4y5uxsH/t34rPjWJqygMulJrVdePpC9fNWwDYnul6T7iF
/bbqIH/j88HSYNDN518dv/ot+OfPn0vuxD4WzGAqC7ddHICtuaw8TBfXHmr6j4Mf
o9ytC/dH+AQ6Tcs+h7mbz/dfL4Gs9JK2LgRX2z1DtFa6uTw5jwEtZSuDF4DKovEg
71T67dsHDKJkQgGMDfDw1BrlLjQr8hkaWroF8CdmbRO0rRsfKamLQANG7mGkSu8B
l1W0ZzWEbHDteNB/wCkjoncXlcqoA8YiplyVSqf38aP8YuaeHMR3LRGLFwgXK3pB
lELh3cYSYLVpcqUgkRWcPrCUnLA2CkQy2B4INj5jFZilux7DzyIHMhWI2OuUs2rH
1rwTYO91gTVONuagZn8+lmsjs+Yq1n2BcyrGMG2+ZYzruFaQ+brQsCbQR0hdRuaU
zWLENqwGJ/++XrFgw3/5orMZIZQzL/yq+MbIXtrgKcFRWwoxyzJuH63RMQf3S6yy
hxi7pYQmb9if+HPJZVVg
=Bb5O
-----END PGP SIGNATURE-----
Merge tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6
Pull battery subsystem updates from Anton Vorontsov:
"Highlights:
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace
the proprietary Nokia BME stack
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks
to Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers
- Random fixups and enhancements for a bunch of drivers."
* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
max8925_power: Add support for device-tree initialization
ab8500: Add devicetree support for chargalg
ab8500: Add devicetree support for charger
ab8500: Add devicetree support for btemp
ab8500: Add devicetree support for fuelgauge
twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
jz4740-battery: Use devm_request_and_ioremap
jz4740-battery: Use devm_kzalloc
bq27x00_battery: Fixup nominal available capacity reporting
bq2415x_charger: Fix style issues
bq2415x_charger: Add Kconfig/Makefile entries
power_supply: Add bq2415x charger driver
power_supply: Add new Nokia RX-51 (N900) power supply battery driver
max17042_battery: Fix missing verify_model_lock() return value check
ds2782_battery: Fix signedness bug in ds278x_read_reg16()
lp8788-charger: Fix ADC channel names
lp8788-charger: Fix wrong ADC conversion
lp8788-charger: Use consumer device name on setting IIO channels
power_supply: Register power supply for thermal cooling device
power_supply: Add support for CHARGE_CONTROL_* attributes
...
Primarily SPI device driver bug fixes, one removal of an old driver, and
some new tegra support. There is some core code change too, but all in
all pretty small stuff. The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bvpH
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI updates from Grant Likely:
"Primarily SPI device driver bug fixes, one removal of an old driver,
and some new tegra support. There is some core code change too, but
all in all pretty small stuff.
The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI"
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (36 commits)
spi/sparc: Allow of_register_spi_devices for sparc
spi: Remove HOTPLUG section attributes
spi: Add support for specifying 3-wire mode via device tree
spi: Fix comparison of different integer types
spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood driver.
spi/sh: Add SH Mobile series as dependency to MSIOF controller
spi/sh-msiof: Remove unneeded clock name
spi: Remove SPI_BUFSIZ restriction on spi_write_then_read()
spi/stmp: remove obsolete driver
spi/clps711x: New SPI master driver
spi: omap2-mcspi: remove duplicate inclusion of linux/err.h
spi: omap2-mcspi: Fix the redifine warning
spi/sh-hspi: add CS manual control support
of_spi: add generic binding support to specify cs gpio
spi: omap2-mcspi: remove duplicated include from spi-omap2-mcspi.c
spi/bitbang: (cosmetic) simplify list manipulation
spi/bitbang: avoid needless loop flow manipulations
spi/omap: fix D0/D1 direction confusion
spi: tegra: add spi driver for sflash controller
spi: Dont call master->setup if not populated
...
A fairly quiet release again, a couple of relatively small new features
and a bunch of driver specific work including yet more code elimination
and fixes from Axel Lin.
- Addidion of linear_min_sel for offsetting linear selectors in the
helpers.
- Support for continuous voltage ranges for regulators with extremely
high resolution.
- Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM vexpress.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2d65
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A fairly quiet release again, a couple of relatively small new
features and a bunch of driver specific work including yet more code
elimination and fixes from Axel Lin.
- Addidion of linear_min_sel for offsetting linear selectors in the
helpers.
- Support for continuous voltage ranges for regulators with extremely
high resolution.
- Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM
vexpress."
Fix up trivial conflict (due to typo fix) in palmas-regulator.c
* tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (80 commits)
regulator: core: Fix logic to determinate if regulator can change voltage
regulator: s5m8767: Fix to work even if no DVS gpio present
regulator: s5m8767: Fix to read the first DVS register.
regulator: s5m8767: Fix to work when platform registers less regulators
regulator: gpio-regulator: gpio_set_value should use cansleep
regulator: gpio-regulator: Fix logical error in for() loop
regulator: anatop: Use regulator_[get|set]_voltage_sel_regmap
regulator: anatop: Use linear_min_sel with linear mapping
regulator: max1586: Implement get_voltage_sel callback
regulator: lp8788-buck: Kill _gpio_request function
regulator: tps80031: Convert tps80031_ldo_ops to linear_min_sel and list_voltage_linear
regulator: lp8788-ldo: Remove val array in lp8788_config_ldo_enable_mode
regulator: gpio-regulator: Add ifdef CONFIG_OF guard for regulator_gpio_of_match
regulator: palmas: Convert palmas_ops_smps to regulator_[get|set]_voltage_sel_regmap
regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
regulators: add regulator_can_change_voltage() function
regulator: tps51632: Ensure [base|max]_voltage_uV pdata settings are valid
regulator: wm831x-dcdc: Add MODULE_ALIAS for wm831x-boostp
regulator: wm831x-dcdc: Ensure selected voltage falls within requested range
regulator: tps51632: Use linear_min_sel and regulator_[map|list]_voltage_linear
...
This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=IIsz
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments"
Fix up trivial conflicts. And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: hda - Move runtime PM check to runtime_idle callback
ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
ALSA: hda - Avoid doubly suspend after vga switcheroo
ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
ALSA: hda - Check validity of CORB/RIRB WP reads
ALSA: hda - use usleep_range in link reset and change timeout check
ALSA: HDA: VIA: Add support for codec VT1808.
ALSA: HDA: VIA Add support for codec VT1705CF.
ASoC: codecs: remove __dev* attributes
ASoC: utils: remove __dev* attributes
ASoC: ux500: remove __dev* attributes
ASoC: txx9: remove __dev* attributes
ASoC: tegra: remove __dev* attributes
ASoC: spear: remove __dev* attributes
ASoC: sh: remove __dev* attributes
ASoC: s6000: remove __dev* attributes
ASoC: OMAP: remove __dev* attributes
ASoC: nuc900: remove __dev* attributes
ASoC: mxs: remove __dev* attributes
ASoC: kirkwood: remove __dev* attributes
...
Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is
not quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq. note
that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UJlh
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform conversion patches from Olof Johansson:
"Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is not
quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq.
Note that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled."
Fix up conflicts mostly as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
clocksource/mtu-nomadik: use apb_pclk
clk: ux500: Register mtu apb_pclocks
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
...
Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms have
seen pinctrl-via-devicetree conversions for simpler multiplatform. Tegra
is adding data for new devices/drivers, and Exynos has a bunch of new
bindings and devices added as well.
So, pretty much the same progression in the right direction as the last
few releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rk9v
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree conversions and enablement from Olof Johansson:
"Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms
have seen pinctrl-via-devicetree conversions for simpler
multiplatform. Tegra is adding data for new devices/drivers, and
Exynos has a bunch of new bindings and devices added as well.
So, pretty much the same progression in the right direction as the
last few releases."
Fix up conflicts as per Olof.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sgYz
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals,
etc."
Fix up conflicts mostly as per Olof.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
ARM: mmp: select pinctrl driver
...
This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's also
taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YMKB
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
Pull ARM updates from Russell King:
"Here's the updates for ARM for this merge window, which cover quite a
variety of areas.
There's a bunch of patch series from Will tackling various bugs like
the PROT_NONE handling, ASID allocation, cluster boot protocol and
ASID TLB tagging updates.
We move to a build-time sorted exception table rather than doing the
sorting at run-time, add support for the secure computing filter, and
some updates to the perf code. We also have sorted out the placement
of some headers, fixed some build warnings, fixed some hotplug
problems with the per-cpu TWD code."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (73 commits)
ARM: 7594/1: Add .smp entry for REALVIEW_EB
ARM: 7599/1: head: Remove boot-time HYP mode check for v5 and below
ARM: 7598/1: net: bpf_jit_32: fix sp-relative load/stores offsets.
ARM: 7595/1: syscall: rework ordering in syscall_trace_exit
ARM: 7596/1: mmci: replace readsl/writesl with ioread32_rep/iowrite32_rep
ARM: 7597/1: net: bpf_jit_32: fix kzalloc gfp/size mismatch.
ARM: 7593/1: nommu: do not enable DCACHE_WORD_ACCESS when !CONFIG_MMU
ARM: 7592/1: nommu: prevent generation of kernel unaligned memory accesses
ARM: 7591/1: nommu: Enable the strict alignment (CR_A) bit only if ARCH < v6
ARM: 7590/1: /proc/interrupts: limit the display of IPIs to online CPUs only
ARM: 7587/1: implement optimized percpu variable access
ARM: 7589/1: integrator: pass the lm resource to amba
ARM: 7588/1: amba: create a resource parent registrator
ARM: 7582/2: rename kvm_seq to vmalloc_seq so to avoid confusion with KVM
ARM: 7585/1: kernel: fix nr_cpu_ids check in DT logical map init
ARM: 7584/1: perf: fix link error when CONFIG_HW_PERF_EVENTS is not selected
ARM: gic: use a private mapping for CPU target interfaces
ARM: kernel: add logical mappings look-up
ARM: kernel: add cpu logical map DT init in setup_arch
ARM: kernel: add device tree init map function
...
Pull thermal management update from Zhang Rui:
"Highlights:
- Introduction of thermal policy support, together with three new
thermal governors, including step_wise, user_space, fire_share.
- Introduction of ST-Ericsson db8500_thermal driver and ST-Ericsson
db8500_cpufreq_cooling driver.
- Thermal Kconfig file and Makefile refactor.
- Fixes for generic thermal layer, generic cpucooling, rcar thermal
driver and Exynos thermal driver."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
Thermal: Fix DEFAULT_THERMAL_GOVERNOR
Thermal: fix a NULL pointer dereference when generic thermal layer is built as a module
thermal: rcar: add rcar_zone_to_priv() macro
thermal: rcar: fixup the unit of temperature
thermal: cpu cooling: allow module builds
thermal: cpu cooling: use const parameter while registering
Thermal: Add ST-Ericsson DB8500 thermal properties and platform data.
Thermal: Add ST-Ericsson DB8500 thermal driver.
drivers/thermal/Makefile refactor
Exynos: Add missing dependency
Refactor drivers/thermal/Kconfig
thermal: cpu_cooling: Make 'notify_device' static
Thermal: Remove the cooling_cpufreq_list.
Thermal: fix bug of counting cpu frequencies.
Thermal: add indent for code alignment.
thermal: rcar_thermal: remove explicitly used devm_kfree/iounap()
thermal: user_space: Add missing static storage class specifiers
thermal: fair_share: Add missing static storage class specifiers
thermal: step_wise: Add missing static storage class specifiers
Thermal: Fix oops and unlocking in thermal_sys.c
...
The merge is merely to fix conflicts before sending a pull request.
Conflicts:
drivers/power/ab8500_btemp.c
drivers/power/ab8500_charger.c
drivers/power/ab8500_fg.c
drivers/power/abx500_chargalg.c
drivers/power/max8925_power.c
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers to
all work together nicer, which was a reduction in overall code. We also
deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a nice
thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhIYACgkQMUfUDdst+yk9gACgsZYgMtbrqdbhbjbYkfO7nYkB
iegAoIvj3qwe33TbZ8OJnIkaWcMiT8CW
=u6Bf
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers
to all work together nicer, which was a reduction in overall code. We
also deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a
nice thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (228 commits)
USB: mark uas driver as BROKEN
xhci: Add Lynx Point LP to list of Intel switchable hosts
uwb: fix uwb_dev_unlock() missed at an error path in uwb_rc_cmd_async()
USB: ftdi_sio: Add support for Newport AGILIS motor drivers
MAINTAINERS: remove drivers/block/ub.c
USB: chipidea: fix use after free bug
ezusb: add dependency to USB
usb: ftdi_sio: fixup BeagleBone A5+ quirk
USB: cp210x: add Virtenio Preon32 device id
usb: storage: remove redundant memset() in usb_probe_stor1()
USB: option: blacklist network interface on Huawei E173
USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue
USB: add new zte 3g-dongle's pid to option.c
USB: opticon: switch to generic read implementation
USB: opticon: refactor reab-urb processing
USB: opticon: use usb-serial bulk-in urb
USB: opticon: increase bulk-in size
USB: opticon: use port as urb context
USB: opticon: pass port to get_serial_info
USB: opticon: make private data port specific
...
Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from Jiri and
bugfixes from Alan, along with a number of other tty and serial driver updates
by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the TTY
layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhgwACgkQMUfUDdst+ynI6wCcC+YeBwncnoWHvwLAJOwAZpUL
bysAn28o780/lOsTzp3P1Qcjvo69nldo
=hN/g
-----END PGP SIGNATURE-----
Merge tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/Serial merge from Greg Kroah-Hartman:
"Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from
Jiri and bugfixes from Alan, along with a number of other tty and
serial driver updates by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the
TTY layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up some trivial conflicts in the staging tree, due to the fwserial
driver having come in both ways (but fixed up a bit in the serial tree),
and the ioctl handling in the dgrp driver having been done slightly
differently (staging tree got that one right, and removed both
TIOCGSOFTCAR and TIOCSSOFTCAR).
* tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (146 commits)
staging: sb105x: fix potential NULL pointer dereference in mp_chars_in_buffer()
staging/fwserial: Remove superfluous free
staging/fwserial: Use WARN_ONCE when port table is corrupted
staging/fwserial: Destruct embedded tty_port on teardown
staging/fwserial: Fix build breakage when !CONFIG_BUG
staging: fwserial: Add TTY-over-Firewire serial driver
drivers/tty/serial/serial_core.c: clean up HIGH_BITS_OFFSET usage
staging: dgrp: dgrp_tty.c: Audit the return values of get/put_user()
staging: dgrp: dgrp_tty.c: Remove the TIOCSSOFTCAR ioctl handler from dgrp driver
serial: ifx6x60: Add modem power off function in the platform reboot process
serial: mxs-auart: unmap the scatter list before we copy the data
serial: mxs-auart: disable the Receive Timeout Interrupt when DMA is enabled
serial: max310x: Setup missing "can_sleep" field for GPIO
tty/serial: fix ifx6x60.c declaration warning
serial: samsung: add devicetree properties for non-Exynos SoCs
serial: samsung: fix potential soft lockup during uart write
tty: vt: Remove redundant null check before kfree.
tty/8250 Add check for pci_ioremap_bar failure
tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards
tty/8250 Add XR17D15x devices to the exar_handle_irq override
...
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2XeO
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO updates from Grant Likely:
"GPIO follow up patch and type change for v3.5 merge window
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio: Provide the STMPE GPIO driver with its own IRQ Domain
gpio: add TS-5500 DIO blocks support
gpio: pcf857x: use client->irq for gpio_to_irq()
gpio: stmpe: Add DT support for stmpe gpio
gpio: pl061 depends on ARM
gpio/pl061: remove old comment
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
...
* Introduction of device PM QoS flags.
* ACPI device power management update allowing subsystems other than
PCI to use it more easily.
* ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
* ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
* ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
* Introduction of acpi_handle_<level>() messaging macros and ACPI-based CPU
hot-remove support from Toshi Kani.
* ACPI EC updates from Feng Tang.
* cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
* cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
* Support for using multiple cpuidle drivers at the same time and cpuidle
cleanups from Daniel Lezcano.
* devfreq updates from Nishanth Menon and others.
* cpupower update from Thomas Renninger.
* Fixes and small cleanups all over the place.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=6OEP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Introduction of device PM QoS flags.
- ACPI device power management update allowing subsystems other than
PCI to use it more easily.
- ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
- ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
- ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
- Introduction of acpi_handle_<level>() messaging macros and ACPI-based
CPU hot-remove support from Toshi Kani.
- ACPI EC updates from Feng Tang.
- cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
- cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
- Support for using multiple cpuidle drivers at the same time and
cpuidle cleanups from Daniel Lezcano.
- devfreq updates from Nishanth Menon and others.
- cpupower update from Thomas Renninger.
- Fixes and small cleanups all over the place.
* tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (196 commits)
mmc: sdhci-acpi: enable runtime-pm for device HID INT33C6
ACPI: add Haswell LPSS devices to acpi_platform_device_ids list
ACPI: add documentation about ACPI 5 enumeration
pnpacpi: fix incorrect TEST_ALPHA() test
ACPI / PM: Fix header of acpi_dev_pm_detach() in acpi.h
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
ACPI : do not use Lid and Sleep button for S5 wakeup
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
spi / ACPI: add ACPI enumeration support
gpio / ACPI: add ACPI support
PM / devfreq: remove compiler error with module governors (2)
cpupower: IvyBridge (0x3a and 0x3e models) support
cpupower: Provide -c param for cpupower monitor to schedule process on all cores
cpupower tools: Fix warning and a bug with the cpu package count
cpupower tools: Fix malloc of cpu_info structure
cpupower tools: Fix issues with sysfs_topology_read_file
cpupower tools: Fix minor warnings
cpupower tools: Update .gitignore for files created in the debug directories
...
Bug fixes, little cleanups, and documentation changes. The most invasive
thing here touches a bunch of the arch directories to use a common build
rule for .dtb files. There are no major changes to functionality here
other than a ew new helper functions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LB3n
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull device tree changes from Grant Likely:
"Here are the DT changes I've got queued up for v3.8. As described
below, there are a lot of bug fixes here and documentation updates but
nothing major:
Bug fixes, little cleanups, and documentation changes. The most
invasive thing here touches a bunch of the arch directories to use a
common build rule for .dtb files. There are no major changes to
functionality here other than a few new helper functions."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
arm64: Fix the dtbs target building
mtd: nand: davinci: fix the binding documentation
rtc: rtc-mv: Add the device tree binding documentation
devicetree/bindings: Move gpio-leds binding into leds directory
of/vendor-prefixes: add Imagination Technologies
microblaze: use new common dtc rule
c6x: use new common dtc rule
openrisc: use new common dtc rule
arm64: Add dtbs target for building all the enabled dtb files
arm64: use new common dtc rule
ARM: dt: change .dtb build rules to build in dts directory
kbuild: centralize .dts->.dtb rule
Fix build when CONFIG_W1_MASTER_GPIO=m b exporting "allnodes"
of/spi: Honour "status=disabled" property of device
of_mdio: Honour "status=disabled" property of device
of_i2c: Honour "status=disabled" property of device
powerpc: Fix fallout from device_node->name constification
of: add 'const' for of_parse_phandle parameter *np
Documentation: correct of_platform_populate() argument list
script: dtc: clean generated files
...