commit ebc68cedec upstream.
The Acer Aspire 5738z has a button to disable (and re-enable) the
touchpad next to the touchpad.
When this button is pressed a LED underneath indicates that the touchpad
is disabled (and an event is send to userspace and GNOME shows its
touchpad enabled / disable OSD thingie).
So far so good, but after re-enabling the touchpad it no longer works.
The laptop does not have an external ps2 port, so mux mode is not needed
and disabling mux mode fixes the touchpad no longer working after toggling
it off and back on again, so lets add this laptop model to the nomux list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200331123947.318908-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da32890448 ]
The Coreriver TouchCore 360 is like the midas board touchkey, but it is
using a fixed regulator.
Signed-off-by: Nick Reitemeyer <nick.reitemeyer@web.de>
Link: https://lore.kernel.org/r/20200121141525.3404-3-nick.reitemeyer@web.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1369d0abe4 upstream.
This laptop (and perhaps other variants of the same model) reports an
SMBus-capable Synaptics touchpad. Everything (including suspend and
resume) works fine when RMI is enabled via the kernel command line, so
let's add it to the whitelist.
Signed-off-by: Yussuf Khalil <dev@pp3345.net>
Link: https://lore.kernel.org/r/20200307213508.267187-1-dev@pp3345.net
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32cf3a610c upstream.
These functions are supposed to return negative error codes but instead
it returns true on failure and false on success. The error codes are
eventually propagated back to user space.
Fixes: 48a2b78348 ("Input: add Raydium I2C touchscreen driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200303101306.4potflz7na2nn3od@kili.mountain
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e112324cc0 ]
The EP0700MLP1 returns bogus data on the first register read access
(reading the threshold parameter from register 0x00):
edt_ft5x06 2-0038: crc error: 0xfc expected, got 0x40
It ignores writes until then. This patch adds a dummy read after which
the number of sensors and parameter read/writes work correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5179a9dfa9 upstream.
The Yoga 11e is using LEN0049, but it doesn't have a trackstick.
Thus, there is no need to create a software top buttons row.
However, it seems that the device works under SMBus, so keep it as part
of the smbus_pnp_ids.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115013023.9710-1-benjamin.tissoires@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf50239135 upstream.
This supports RMI4 and everything seems to work, including the touchpad
buttons. So, let's enable this by default.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200204194322.112638-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce535a2efb ]
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the onkey driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f439bc2d7 ]
We observed a large(order-3) allocation in evdev_open() and it may
cause an OOM kernel panic in kzalloc(), before we getting to the
vzalloc() fallback.
Fix it by converting kzalloc()/vzalloc() to kvzalloc() to avoid the
OOM killer logic as we have a vmalloc fallback.
InputReader invoked oom-killer: gfp_mask=0x240c2c0
(GFP_KERNEL|__GFP_NOWARN|__GFP_COMP|__GFP_ZERO), nodemask=0, order=3,
oom_score_adj=-900
...
(dump_backtrace) from (show_stack+0x18/0x1c)
(show_stack) from (dump_stack+0x94/0xa8)
(dump_stack) from (dump_header+0x7c/0xe4)
(dump_header) from (out_of_memory+0x334/0x348)
(out_of_memory) from (__alloc_pages_nodemask+0xe9c/0xeb8)
(__alloc_pages_nodemask) from (kmalloc_order_trace+0x34/0x128)
(kmalloc_order_trace) from (__kmalloc+0x258/0x36c)
(__kmalloc) from (evdev_open+0x5c/0x17c)
(evdev_open) from (chrdev_open+0x100/0x204)
(chrdev_open) from (do_dentry_open+0x21c/0x354)
(do_dentry_open) from (vfs_open+0x58/0x84)
(vfs_open) from (path_openat+0x640/0xc98)
(path_openat) from (do_filp_open+0x78/0x11c)
(do_filp_open) from (do_sys_open+0x130/0x244)
(do_sys_open) from (SyS_openat+0x14/0x18)
(SyS_openat) from (__sys_trace_return+0x0/0x10)
...
Normal: 12488*4kB (UMEH) 6984*8kB (UMEH) 2101*16kB (UMEH) 0*32kB
0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 139440kB
HighMem: 206*4kB (H) 131*8kB (H) 42*16kB (H) 2*32kB (H) 0*64kB
0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2608kB
...
Kernel panic - not syncing: Out of memory and no killable processes...
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97e24b0953 upstream.
The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.
Fixes: e28d0c9cd3 ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcfcb7f9b4 upstream.
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could be used by a
malicious device (or USB descriptor fuzzer) to trigger a NULL-pointer
dereference.
Fixes: 1afca2b66a ("Input: add Pegasus Notetaker tablet driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-2-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3111491fca upstream.
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-3-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8eeb74df5 upstream.
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 162f98dea4 ("Input: gtco - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-5-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b32391ed6 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 996d5d5f89 upstream.
Setting the vibrator enable_mask is not implemented correctly:
For regmap_update_bits(map, reg, mask, val) we give in either
regs->enable_mask or 0 (= no-op) as mask and "val" as value.
But "val" actually refers to the vibrator voltage control register,
which has nothing to do with the enable_mask.
So we usually end up doing nothing when we really wanted
to enable the vibrator.
We want to set or clear the enable_mask (to enable/disable the vibrator).
Therefore, change the call to always modify the enable_mask
and set the bits only if we want to enable the vibrator.
Fixes: d4c7c5c96c ("Input: pm8xxx-vib - handle separate enable register")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200114183442.45720-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ff771f8c8 upstream.
This reverts commit a284e11c37.
This causes problems (drifting cursor) with at least the F11 function that
reads more than 32 bytes.
The real issue is in the F54 driver, and so this should be fixed there, and
not in rmi_smbus.c.
So first revert this bad commit, then fix the real problem in F54 in another
patch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Fixes: a284e11c37 ("Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115124819.3191024-2-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba9a103f40 upstream.
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 99f83c9c9a ("[PATCH] USB: add driver for Keyspan Digital Remote")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 2.6.13
Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f729a1b0f8 upstream.
Going through all uses of timeval, I noticed that we screwed up
input_event in the previous attempts to fix it:
The time fields now match between kernel and user space, but all following
fields are in the wrong place.
Add the required padding that is implied by the glibc timeval definition
to fix the layout, and use a struct initializer to avoid leaking kernel
stack data.
Fixes: 141e5dcaa7 ("Input: input_event - fix the CONFIG_SPARC64 mixup")
Fixes: 2e746942eb ("Input: input_event - provide override for sparc64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191213204936.3643476-2-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43f06a4c63 ]
input_mt_init_slots() may fail and we need to handle such failures.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efd7bb08a7 ]
We should not be putting the chip into reset while interrupts are enabled
and ISR may be running. Fix this by installing a custom devm action and
powering off the device/resetting GPIO line from there. This ensures proper
ordering.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 463fa44eec ]
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
In the implementation of psxpad_spi_probe() the allocated memory for
pdev is leaked if psxpad_spi_init_ff() or input_register_polled_device()
fail. The solution is using device managed allocation, like the one used
for pad. Perform the allocation using
devm_input_allocate_polled_device().
Fixes: 8be193c7b1 ("Input: add support for PlayStation 1/2 joypads connected via SPI")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df5b5e555b upstream.
The touchscreen on the Teclast X89 is mounted upside down in relation to
the display orientation (the touchscreen itself is mounted upright, but the
display is mounted upside-down). Add a quirk for this so that we send
coordinates which match the display orientation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20191202085636.6650-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a284e11c37 upstream.
This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.
The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.
I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.
It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.
With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/8dd22e21-4933-8e9c-a696-d281872c8de7@xs4all.nl
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86bcd3a129 upstream.
F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.
The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.
Fixes: 363c53875a (Input: synaptics-rmi4 - avoid processing unknown IRQs)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191129133514.23224-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull input fix from Dmitry Torokhov:
"Just a single revert as RMI mode should not have been enabled for this
model [yet?]"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - enable RMI mode for X1 Extreme 2nd Generation"
This reverts commit 68b9c5066e39af41d3448abfc887c77ce22dd64d.
Ugh, I really dropped the ball on this one :\. So as it turns out RMI4
works perfectly fine on the X1 Extreme Gen 2 except for one thing I
didn't notice because I usually use the trackpoint: clicking with the
touchpad. Somehow this is broken, in fact we don't even seem to indicate
BTN_LEFT as a valid event type for the RMI4 touchpad. And, I don't even
see any RMI4 events coming from the touchpad when I press down on it.
This only seems to work for PS/2 mode.
Since that means we have a regression, and PS/2 mode seems to work fine
for the time being - revert this for now. We'll have to do a more
thorough investigation on this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191119234534.10725-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input fixes from Dmitry Torokhov:
"A couple of fixes in driver teardown paths and another ID for
Synaptics RMI mode"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - enable RMI mode for X1 Extreme 2nd Generation
Input: synaptics-rmi4 - destroy F54 poller workqueue when removing
Input: ff-memless - kill timer in destroy()
Just got one of these for debugging some unrelated issues, and noticed
that Lenovo seems to have gone back to using RMI4 over smbus with
Synaptics touchpads on some of their new systems, particularly this one.
So, let's enable RMI mode for the X1 Extreme 2nd Generation.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191115221814.31903-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver forgets to destroy workqueue in remove() similarly to what is
done when probe() fails. Add a call to destroy_workqueue() to fix it.
Since unregistration will wait for the work to finish, we do not need to
cancel/flush the work instance in remove().
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191114023405.31477-1-hslester96@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Fixes to the Synaptics RMI4 driver and fix for use after free in error
path handling of the Cypress TTSP driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyttsp4_core - fix use after free bug
Input: synaptics-rmi4 - clear IRQ enables for F54
Input: synaptics-rmi4 - remove unused result_bits mask
Input: synaptics-rmi4 - do not consume more data than we have (F11, F12)
Input: synaptics-rmi4 - disable the relative position IRQ in the F12 driver
Input: synaptics-rmi4 - fix video buffer size
The device md->input is used after it is released. Setting the device
data to NULL is unnecessary as the device is never used again. Instead,
md->input should be assigned NULL to avoid accessing the freed memory
accidently. Besides, checking md->si against NULL is superfluous as it
points to a variable address, which cannot be NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1572936379-6423-1-git-send-email-bianpan2016@163.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver for F54 just polls the status and doesn't even have a IRQ
handler registered. Make sure to disable all F54 IRQs, so we don't crash
the kernel on a nonexistent handler.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191105114402.6009-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, rmi_f11_attention() and rmi_f12_attention() functions update
the attn_data data pointer and size based on the size of the expected
size of the attention data. However, if the actual valid data in the
attn buffer is less then the expected value then the updated data
pointer will point to memory beyond the end of the attn buffer. Using
the calculated valid_bytes instead will prevent this from happening.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191025002527.3189-3-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes an issue seen on HID touchpads which report finger
positions using RMI4 Function 12. The issue manifests itself as
spurious button presses as described in:
https://www.spinics.net/lists/linux-input/msg58618.html
Commit 24d28e4f12 ("Input: synaptics-rmi4 - convert irq distribution
to irq_domain") switched the RMI4 driver to using an irq_domain to handle
RMI4 function interrupts. Functions with more then one interrupt now have
each interrupt mapped to their own IRQ and IRQ handler. The result of
this change is that the F12 IRQ handler was now getting called twice. Once
for the absolute data interrupt and once for the relative data interrupt.
For HID devices, calling rmi_f12_attention() a second time causes the
attn_data data pointer and size to be set incorrectly. When the touchpad
button is pressed, F30 will generate an interrupt and attempt to read the
F30 data from the invalid attn_data data pointer and report incorrect
button events.
This patch disables the F12 relative interrupt which prevents
rmi_f12_attention() from being called twice.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Simon Wood <simon@mungewell.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191025002527.3189-2-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The video buffer used by the queue is a vb2_v4l2_buffer, not a plain
vb2_buffer. Using the wrong type causes the allocation of the buffer
storage to be too small, causing a out of bounds write when
__init_vb2_v4l2_buffer initializes the buffer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191104114454.10500-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fix from Dmitry Torokhov:
"A fix for st1232 driver to properly report coordinates for 2nd and
subsequent fingers when more than one is on the surface"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: st1232 - fix reporting multitouch coordinates
Pull input fixes from Dmitry Torokhov:
"The main change is that we are reverting blanket enablement of SMBus
mode for devices with Elan touchpads that report BIOS release date as
2018+ because there are older boxes with updated BIOSes that still do
not work well in SMbus mode.
We will have to establish whitelist for SMBus mode it looks like"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: elantech - enable SMBus on new (2018+) systems"
Input: synaptics-rmi4 - avoid processing unknown IRQs
Input: soc_button_array - partial revert of support for newer surface devices
Input: goodix - add support for 9-bytes reports
Input: da9063 - fix capability and drop KEY_SLEEP
This reverts commit 883a2a80f7.
Apparently use dmi_get_bios_year() as manufacturing date isn't accurate
and this breaks older laptops with new BIOS update.
So let's revert this patch.
There are still new HP laptops still need to use SMBus to support all
features, but it'll be enabled via a whitelist.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191001070845.9720-1-kai.heng.feng@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rmi_process_interrupt_requests() calls handle_nested_irq() for
each interrupt status bit it finds. If the irq domain mapping for
this bit had not yet been set up, then it ends up calling
handle_nested_irq(0), which causes a NULL pointer dereference.
There's already code that masks the irq_status bits coming out of the
hardware with current_irq_mask, presumably to avoid this situation.
However current_irq_mask seems to more reflect the actual mask set
in the hardware rather than the IRQs software has set up and registered
for. For example, in rmi_driver_reset_handler(), the current_irq_mask
is initialized based on what is read from the hardware. If the reset
value of this mask enables IRQs that Linux has not set up yet, then
we end up in this situation.
There appears to be a third unused bitmask that used to serve this
purpose, fn_irq_bits. Use that bitmask instead of current_irq_mask
to avoid calling handle_nested_irq() on IRQs that have not yet been
set up.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20191008223657.163366-1-evgreen@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit c394159310 ("Input: soc_button_array - add support for newer
surface devices") not only added support for the MSHW0040 ACPI HID,
but for some reason it also makes changes to the error handling of the
soc_button_lookup_gpio() call in soc_button_device_create(). Note ideally
this seamingly unrelated change would have been made in a separate commit,
with a message explaining the what and why of this change.
I guess this change may have been added to deal with -EPROBE_DEFER errors,
but in case of the existing support for PNP0C40 devices, treating
-EPROBE_DEFER as any other error is deliberate, see the comment this
commit adds for why.
The actual returning of -EPROBE_DEFER to the caller of soc_button_probe()
introduced by the new error checking causes a serious regression:
On devices with so called virtual GPIOs soc_button_lookup_gpio() will
always return -EPROBE_DEFER for these fake GPIOs, when this happens
during the second call of soc_button_device_create() we already have
successfully registered our first child. This causes the kernel to think
we are making progress with probing things even though we unregister the
child before again before we return the -EPROBE_DEFER. Since we are making
progress the kernel will retry deferred-probes again immediately ending
up stuck in a loop with the following showing in dmesg:
[ 124.022697] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6537
[ 124.040764] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6538
[ 124.056967] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6539
[ 124.072143] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6540
[ 124.092373] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6541
[ 124.108065] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6542
[ 124.128483] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6543
[ 124.147141] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6544
[ 124.165070] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6545
[ 124.179775] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6546
[ 124.202726] input: gpio-keys as /devices/platform/INTCFD9:00/gpio-keys.0.auto/input/input6547
<continues on and on and on>
And 1 CPU core being stuck at 100% and udev hanging since it is waiting
for the modprobe of soc_button_array to return.
This patch reverts the soc_button_lookup_gpio() error handling changes,
fixing this regression.
Fixes: c394159310 ("Input: soc_button_array - add support for newer surface devices")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205031
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20191005105551.353273-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some variants of Goodix touchscreen firmwares use 9-bytes finger
report format instead of common 8-bytes format.
This report format may be present as:
struct goodix_contact_data {
uint8_t unknown1;
uint8_t track_id;
uint8_t unknown2;
uint16_t x;
uint16_t y;
uint16_t w;
}__attribute__((packed));
Add support for such format and use it for Lenovo Yoga Book notebook
(which uses a Goodix touchpad as a touch keyboard).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit f889beaaab ("Input: da9063 - report KEY_POWER instead of
KEY_SLEEP during power key-press") KEY_SLEEP isn't supported anymore. This
caused input device to not generate any events if "dlg,disable-key-power"
is set.
Fix this by unconditionally setting KEY_POWER capability, and not
declaring KEY_SLEEP.
Fixes: f889beaaab ("Input: da9063 - report KEY_POWER instead of KEY_SLEEP during power key-press")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>